Chief KTA1005B mounting kit
Contents
1. 5 KTA1005 Installation Instructions Installation Instructions KTA1005 KTA1005 a CHIEF Our Mounts Your Vision Chief Manufacturing a division of Milestone AV Technologies 8832 000257 2008 Milestone AV Technologies www chiefmfg com 07 08 Installation Instructions USA International 8401 Eagle Creek Parkway Savage 55378 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA JR I rh A STRANE XE D ER24F 86 755 8996 9226 86 755 8996 9217 P os Asia Pacific Consumer2. INSTALLATION INSTRUCTIONS J x 4 CA 2 1 F WM 12 D 22 Y os WO Array Centris Accessory S CHIEF KTA1005 Our Mounts Your Vision KTA1005 DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND Tighten Fastener Serrez les fixations Loosen Fastener Installation Instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the cor
3. ON The following procedure assumes a base and pole have been purchased and are available The procedure also assumes that no displays are mounted to the array 1 Assemble pole and base following instructions included with those kits 2 Slide display with Centris bracket onto mounting rail See Figure 1 Tighten to mounting rail Square Nut KTA 1005 End Lock Figure 1 3 Install end locks into mounting rail See Figure 1 4 Tighten inner knob to tighten array head to mounting rail 5 Determine mounting pattern on display WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only hardware supplied by manufacturer WARNING IMPROPER INSTALLATION CAN LEAD TO ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT Screw length must not exceed the depth of threaded mounting insert in display WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes Ensure that screws are not too long WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of mounting plate Install
4. ation Instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Support and arrange existing monitors or devices along with those being installed to ensure an overall balanced weight distribution This is especially important in free standing units Display Installation Flush Mount Display 1 Start two M4 x 12mm Phillips pan head screws B into upper mounting holes in display back See Figure 2 NOTE Leave at least 1 8 of each screw protruding out back of display 5 Figure 2 Align two screws in display back with upper teardrop mounting holes in KTA 1005 Place two screws in display back into upper teardrop mounting holes in KTA 1005 and lower display until screws are seated in lower area of teardrop mounting holes See Figure 3 Install two screws through display mounting plate and into lower mounting holes in display back See Figure 3 Figure 3 Tighten all hardware Installation Instructions KTA1005 Display Installation Recessed Mount Display 1 Secure display to Centris head using four 3 8 E or 3 4 F nylon spacers and four M4 x 20mm or four M4 x 30mm D Phillips pan head screws into four mounting holes in display back See Figure 4 Figure 4 Adjustments 1 Tighten the outer knob to adjust pitch tension See Figure 5 Adjust pitch Figure
5. responding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment See the installation instructions that came with the array onto which this accessory is being installed for weight limits The accessory s weight capacity is 40 Ibs 18 1 kg Adjust Ajustar E Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Installation Instructions KTA1005 TOOLS REQUIRED FOR INSTALLATION AND PARTS N C 22 E RS LO eg i p 3 SS 2 77 11 4 D 4 M4 x 12mm M4 x 20mm M4 x 30mm F 4 50 x 194 x 375 50 x 194 x 750 E 4 KTA1005 ASSEMBLY and INSTALLATI
Download Pdf Manuals
Related Search