Chief JPP210S mounting kit
Contents
1. 2008 Milestone AV Technologies www chiefmfg com 06 08 A P F A P F A 570 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang Buji Town Shenzhen CHINA JT 6 2 RN BE RES ER 86 755 8996 9226 86 755 8996 9217 x 2 4 Wen o o SP CopsumERS2. INSTALLATION INSTRUCTIONS Interface Bracket for J Series CHIEF JSB210 Our Mounts Your Vision JSB210 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations CAUTION A CAUTION alerts you to the possibility of and subsidiaries intend to make this manual accurate and damage or destruction of equipment if you do not follow the complete However Milestone makes no claim that the corresponding instructions information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The WARNING Failure to read thoroughly understand and information contained in this document is subject to change follow all instructions can result in serious personal injury without notice or obligation of any kind Milestone makes no damage to equipment or voiding of factory warranty It is the representation of warranty expressed or implied regarding the installer s responsibility to make sure all components are information contained herein Milestone assumes no properly assembled and installed using the instructions responsibility for accuracy completeness or sufficiency of the provided information contained in this document WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s
3. JSB210 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 2 22 Provided Provided Q A 1 e e 8 BAGI 4 Sai eg B 4 C 4 D 6 E 4 M4 x 8mm M4 x 12mm M4 x 16mm M4 x 20mm BAG2 e e ei 4 G 4 H 4 J 6 K 4 M5 x 20mm M5 x 30mm M5 x 45mm 194x 625x 125 10 24 BAG 3 GE e 2 L 4 M 4 N 4 P 4 M6 x 20mm M6 x 30mm M6 x 45mm 740x 250x 250 Q 1 1 802 3 16 Installation Instructions JSB210 INSTALLATION WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT substitute hardware Only use hardware provided or specified by manufacturer 1 Determine pattern of mounting holes in back of display WARNING IMPROPER INSTALLATION CAN LEAD TO DAMAGE TO EQUIPMENT OR TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY Use proper size and length hardware depending on display 200mm x 100mm Mounting Hole Pattern 2 Use six nylon spacers J and six flat head screws D to attach JSB210 interface bracket to the display back See Figure 1 aS Figure 1 200mm x 200mm Mounting Hole Pattern 3 Use four nylon spacers J or P and four Phillips cap head screws E through H L through N to attach JSB210 interface bracket to the display back See Figure 2 NOTE Phillips cap head screws should be placed throug
4. h either the square or round holes in the interface bracket corners Use M4 cap head screws through SQUARE holes Use M6 cap head screws through ROUND holes 4 screws placed through square holes o J or P x 4 M6 screws placed through Re round holes E through lt gt L through N x 4 Figure 2 CAUTION PREVENT EQUIPMENT DAMAMGE Tighten each screw carefully but do NOT overtighten Attach Display to Mount 1 Start two Phillips pan head screws into top mounting holes on interface bracket A See Figure 3 2 Align two screws in interface bracket A with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes See Figure 3 Figure 3 JSB210 Installation Instructions 3 Hold display so that display back is against Centris cup and install two Phillips pan head machine screws through lower mounting holes in Centris cup and into lower mounting holes in interface bracket A See Figure 4 Figure 4 4 Complete installation of mount to display following instructions included with the mount Installation Instructions JSB210 JSB210 Installation Instructions E USA International Our Mounts Your Vision Europe Chief Manufacturing a division of Milestone AV Technologies Asia Pacific 8832 000251
5. nto de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand mano Von Hand Com a mao A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y 4 9 2 Hex Head Wrench Llave de cabeza hexagonal Q Sechskantschl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit
6. responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the A IMPORTANT WARNINGS AND component CAUTIONS Chief and Centris TM are registered trademarks of Milestone AV Technologies All rights reserved WARNING Exceeding the weight capacity of the mount can result in serious personal injury or damage to equipment WARNING A WARNING alerts you to the possibility of It is the installer s responsibility to make sure the combined serious injury or death if you do not follow the instructions weight of the mount and all attached components does not exceed 75 lbs 34 kg DIMENSIONS 228 60 9 00 200 7 87 100 3 94 OF 200 228 60 7 87 100 9 00 ALL MEASUREMENTS ARE IN 63 50 THE FOLLOWING FORMAT 2 50 MILLIMETERS 4X M4 X 0 7 TAPPED HOLE ees Installation Instructions JSB210 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar eleme
Download Pdf Manuals
Related Search