NEC MultiSync LCD175M
Contents
1. 640 x 480 at 60 Hz to 75 Hz 800 x 600 at 56 Hz to 75 Hz 832 x 624 at 75 Hz 1024 x 768 at 60 Hz to 75 Hz 1152 x 864 at 75 Hz 1152 x 870 at 75 Hz 1280 x 960 at 60 Hz to 75 Hz 1280 x 1024 at 60 Hz to 75 H 337 9 mm 270 3 mm 1 0W 1 0W 100 240 V 50 60 Hz 0 5 0 3 A with Audio 27 W 19 W Notes Active matrix thin film transistor TFT liquid crystal display LCD 0 264 mm dot pitch 250 cd m white luminance 1000 1 contrast ratio typical 0 7 Vp p 75 Ohms Separate sync TTL Level Positive Negative DVI HDCP 1 Vrms input Depends on display card used Automatically Automatically Some systems may not support all modes listed Recommended resolution is 60 Hz for optimal display performance 368 0 mm W x 358 5 408 5 mm H x 230 0 mm D 14 5 inches W x 14 1 16 1 inches 5 2 kg 11 5 Ibs 5 C to 35 C 41 F to 95 F 20 to 80 0 to 2 000 m 0 to 6 562 Feet 10 C to 60 C 14 F to 140 F 10 to 85 0 to 12 192 m 0 to 40 000 Feet H x 9 1 inches D 1 Interpolated Resolutions When resolutions are shown that are lower than the pixel count of the LCD module text may appear different This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be don2. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation 19 W Default setting Audio sleeping Green Energy Saving Mode 0 40 W Orange Off Mode 0 35 W Unlit WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidan
3. and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Declaration of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Blvd Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Models MultiSync LCD175M L174F1 FE We hereby declare that the equipment specified above conforms to the technical standards as specified
4. ensures that your display is designed manufactured and tested according to some of the strictest quality and environmental requirements in the world This makes for a high performance product designed with the user in focus that also minimizes the impact on the climate and our natural environment TCO Certified is a third party verified program where every product model 1s tested by an accredited impartial test laboratory TCO Certified represents one of the toughest certifications for displays worldwide Some of the Usability features of the TCO Certified for displays e Good visual ergonomics and image quality is tested to ensure top performance and reduce sight and strain problems Important parameters are luminance contrast resolution black level gamma curve color and luminance uniformity color rendition and image stability e Product have been tested according to rigorous safety standards at an impartial laboratory e Electric and magnetic fields emissions as low as normal household background levels e Low acoustic noise emissions Some of the Environmental features of the TCO Certified for displays e The brand owner demonstrates corporate social responsibility and has a certified environmental management system EMAS or ISO 14001 e Very low energy consumption both in on and standby mode minimize climate impact e Restrictions on chlorinated and brominated flame retardants plasticizers plastics and heavy metals
5. NEC MultiSync LCD175M User s Manual Index Wam ng COR E E English 1 Registration MORN OW EE English 1 FCCOMMENGCd USD o ean a E E rain ir English 3 BE e E EE EAS EE A een ine English 5 OO e e T EE E EE EEEE T EEEO EAE A EAEE E English 5 CONTOS e do er English 8 DOC ORS ee e a A ne 0 English 11 DEC LU ESS nia ione English 12 LOUIS SOI a na D ae alii English 13 TCODI DOY lan English 14 Manufacturer s Recycling and Energy Information English 15 WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit A This symbol alerts the user that important literature concerning the operation and maintenance of this un
6. P Press JH w o p SELECT mi LD Fi ll SELECT mon E BI Hl key WE R G B key MIE R G 8B EAT gt An 1 D SUE YOLUME 31 5kHz 60 0Hz 640X480 HEE MUTE Press SELECT key Adjust by using or Example Tool AUT D ES Hll B q5 AUTO 3 11 NATIVE i nDe 92 Di Press SELECT key y 1 D SUB 31 5kHz 60 0Hz 640X480 Press SELECT key TOOL TOOL E2 ETODL i Press n Press ___ Ad er xyO Doc SR ILL Ad E Gm xy DICO ia Fd E Go xy0 DC SA Or 2 Oor Z dpm fo ee NECDISPLAYSOLUTIONS COM NECDISPLAYSOLUTIONS COM Sub Menu Icon Select Press SELECT key TOOL NECDISPLAYSOLUTIONS COM Adjust by using Or 32 E fam xy D E D OSD TURN OFF g 45SEC Sub Menu Adjust English 8 AUTO D AUTO 3 1 H NATIVE d AUDIO Controls the volume of the speakers or headphones To mute the speaker output press the 142 RESET button BRIGHTNESS Adjusts the overall image and background screen brightness To enter the ECO MODE press the 1 2 RESET button ECO MODE OFF Sets brightness variable to 100 ECO MODE1 Sets brightness to 80 This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement conditions ECO MODE2 Sets brightness to 30 This setting can adjust brightness to a range in which power is reduced by 30 compared to the maximum brigh
7. ally optimizing display performance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts monitor to the display card s scanning frequency thus displaying the resolution required FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size VESA Standard Mounting Interface Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket Allows for the monitor to be mounted on a wall or an arm using any third party compliant device Environmental Impact Annual typical maximum operating carbon footprint of this monitor world wide average is approximately 24 5 kg calculated by rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power to Carbon conversion factor conversion factor is based on OECD publication of global CO2 emissions 2008 Edition This monitor has a manufacturing carbon footprint of approximately 15 8 kg Note The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors English 12 Troubleshooting No picture e The signal cable should be c
8. are available in nine languages OSD TURN OFF The OSD control menu will stay on as long as it is in use In the OSD Turn OFF submenu you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu The preset choices are 10 120 seconds by 5 second steps OSD LOCK OUT This control completely locks out access to all OSD control functions with the exception of Brightness and Contrast When attempting to activate OSD controls while in the Lock Out mode a screen will appear indicating the OSD is locked out To activate the OSD Lock Out function press 142 RESET then button and hold down simultaneously To de activate the OSD Lock Out press 12 RESET then button and hold down simultaneously DDC CI Turns ON or OFF the two way communication and control of the monitor MONITOR INFO Indicates the model and serial numbers of your monitor CARBON SAVINGS Display the estimated carbon saving information in kg The carbon footprint factor in the carbon saving calculation is based on the OECD 2008 Edition The carbon saving information can be reset by pressing the 12 RESET button OSD Warning OSD Warning menus disappear with SELECT button NO SIGNAL This function gives a warning when there is no signal present After power is turned on or when there is a change of input signal or video is inactive the No Signal window will appear RESOLUTION NOTIFIER This functi
9. ce of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 15
10. e NOTE Technical specifications are subject to change without notice English 11 Features Reduced Footprint Provides the ideal solution for environments requiring superior image quality but with size and weight limitations The small footprint and light weight allow it to be moved or transported easily from one location to another Colour Control Systems Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards OSD On Screen Display Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus NaViSet software Offers an expanded and intuitive graphical interface allowing you to more easily adjust OSD display settings via mouse and keyboard No touch Auto Adjust No touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup ErgoDesign Features Enhance human ergonomics to improve the working environment protect the health of the user and save money Examples include OSD controls for quick and easy image adjustments tilt base for preferred angle of vision small footprint and compliance with MPRII and TCO guidelines for lower emissions Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatic
11. erformance allow 20 minutes for warm up e Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen e Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes The optimal distance is 50 cm e Rest your eyes periodically by focusing on an object at least 6 m away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen e If reflected light makes it hard for you to see your screen use an antiglare filter e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness and contrast controls to enhance readability e Use a document holder placed close to the screen e Position whatever you are looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomics benefits we recommend the following e Use the preset Size and Position controls with standard signals e Use the preset Colour Setti
12. h care e If you notice any structural damage such as cracks or unnatural wobbling e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor ONE The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Image Persistence Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English 3 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR e For optimum p
13. in the FCC Rules Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation ErgoDesign is a registered trademark of NEC Display Solutions Ltd in Austria Benelux Denmark France Germany Italy Norway Spain Sweden U K All other brands and product names are trademarks or registered trademarks of their respective owners ENERGY STAR is a U S registered trademark As an ENERGY StAR Partner NEC Display Solutions of America Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency The ENercy Star emblem does not represent EPA endorsement of any product or service English 2 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping o
14. it has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this display in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC E I of the power outlet and has been approved by and Ts with the safety standard of your particular country E 1 Puy Type North America America E 1 Chinese FRAI Country U USA Canada A Canada EU except UK EU except UK K Ching om gm rm e a When operating the MultiSync LCD175M monitor with its AC 125 240V power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE This product can only be serviced in the country where it was purchased Registration Information Declaration Declaration of the Manufacturer We hereby certify that the colour monitor MultiSync and marked with LCD175M L174F 1 is in compliance with Council Directive 2006 95 EC EN 60950 1 Council Directive 2004 108 EC EN 55022 _ EN 61000 3 2 NEC Display Solutions Ltd EN 61000 3 3 4 13 23 Shibaura Minato Ku EN 55024 Tokyo 108 0023 Japan ENERGY STAR English 1 Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus mee
15. ith tilt base e Audio Cable e Power Cord e Video Signal Cable 15 pin mini D SUB male to 15 pin mini D SUB male e Setup Manual e CD ROM only EU e Cable management cover Setup Manual lee Setup Manual Audio Cable Power Cord 15 pin mini D SUB Cable management mens male to 15 pin mini cover MultiSync LCD monitor D SUB male Remember to save your original box and packing material to transport or ship the monitor Quick Start To pull the stand follow these instructions 1 Place monitor face down on a non abrasive surface Figure 1 2 Pull the stand holding the monitor with the other hand until the stand clicks Figure 2 NOTE Handle with care when pulling the stand Figure 1 Figure 2 NOTE Reverse this procedure if you need to re pack the monitor To attach the Multisync LCD monitor to your system follow these instructions 1 Turn off the power to your computer 2 For the PC or MAC with DVI digital output Connect the DVI D signal cable to the connector of the display card in your system Figure A 1 Tighten all screws For the PC with Analog output Connect the 15 pin mini D SUB signal cable to the connector of the display card in your system Figure A 2 Tighten all screws For the Mac Connect the MultiSync Macintosh cable adapter not included to the computer Attach the 15 pin mini D SUB signal cable to the MultiSync Macintosh cable adapter Figure A 3 Tighten all screws NOTE Some Macin
16. l cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total When the display mode is changed the OSD Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e lf your text is garbled change the video mode to non interlace and use 60 Hz refresh rate Picture is not as bright e Make sure ECO MODE is turned off LED on monitor is not lit no green or amber colour can be seen e Power Switch should be in the ON position and power cord should be connected Display image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the H SIZE e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode No Video e f no video is present on the screen turn the Power button off and on again e Make certain the computer is not in a power saving mode touch the keyboard or mouse No Sound e Check to see if speaker cable is properly connected e Check to see if mute is activated e Check to see if volume in OSD is set at minimum English 13 TCO Displays 5 0 Congratulations This display is designed for both you and the planet The display you have just purchased carries the TCO Certified label This
17. ng e Use non interlaced signals with a vertical refresh rate between 60 75 Hz e Do not use primary colour blue on a dark background as it is difficult to see and may produce eye fatigue to insufficient contrast Cleaning the LCD Panel e When the liquid crystal panel becomes dusty or dirty wipe gently with a soft cloth e Do not rub the LCD panel with coarse or hard material e Do not apply pressure to the LCD surface e Do not use OA cleaner as it will cause deterioration or discoloration to the LCD surface Cleaning the Cabinet e Unplug the power supply e Dampen a soft cloth with water and a neutral detergent Gently wipe the cabinet then dry gently with a soft cloth NOTE Many plastics are used on the surface of the cabinet DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Do not touch rubber or vinyl to the cabinet for a long period of time These types of fluids and fabrics can cause the paint to deteriorate crack or peel For more detailed information on setting up a healthy work environment write to the American National Standard for Human Factors Engineering of Visual Display Terminal Workstations ANSI HFS Standard No 100 1988 The Human Factors Society Inc PO Box 1369 Santa Monica California 90406 English 4 Contents Your new NEC MultiSync LCD monitor box should contain the following e MultiSync LCD monitor w
18. ompletely connected to the display card computer e The display card should be completely seated in its slot e Check front power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins e Check the signal input Power Button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor Image persistence e Image persistence is when a ghost of an image remains on the screen even after the monitor has been turned off Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn the monitor off for as long as an image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Image is unstable unfocused or swimming is apparent e Signa
19. on gives a warning of use with optimized resolution After power is turned on or when there is a change of input signal or the video signal doesn t have proper resolution the Resolution Notifier window will open This function can be disabled in the TOOL menu OUT OF RANGE This function gives a recommendation of the optimized resolution and refresh rate After the power is turned on or there is a change of input signal or the video signal doesn t have proper timing the Out Of Range menu will appear English 10 Specifications Monitor Specifications LCD Module Diagonal Viewable Image Size Native Resolution Pixel Count Input Signal 15 pin Mini D Sub DVI D Audio input Output Signal Headphones Display Colours Viewing Angle Left Right Up Down Synchronization Range Horizontal Vertical Resolutions Supported Landscape Active Display Area Horizontal Vertical Speakers Practical Audio Output Power Supply Current Rating Power Consumption Dimensions Weight Environmental Considerations Operating Temperature Humidity Altitude Storage Temperature Humidity Altitude Maximun Operation Normal Operation Landscape MultiSync LCD175M Monitor 43 cm 17 inches 43 cm 17 inches 1280 x 1024 Analog RGB Sync Digital RGB Stereo Mini Jack Stereo Mini Jack 16 7 M 80 80 CR gt 10 80 80 CR gt 10 31 5 KHZ to 81 1 kHz 56 Hz to 76 Hz 720 x 400 VGA text
20. optimal settings upon initial setup for most timings For further adjustments use the following OSM controls e Auto Adjust Contrast e Auto Adjust Refer to the Controls section of this User s Manual for a full description of these OSM controls NOTE If you have any problem please refer to the Troubleshooting section of this User s Manual Raise and Lower Monitor Screen The monitor may be raised or lowered To raise or lower screen place hands on each side of the monitor and lift or lower to the desired height Figure RL 1 NOTE Handle with care when raising or lowering the monitor screen Figure RL 1 Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired LY Figure TS 1 Figure TS 1 English 6 Remove Monitor Stand for Mounting To prepare the monitor for alternative mounting purposes 1 Disconnect all cables 2 Place monitor face down on a non abrasive surface Figure R 1 3 Remove the 4 screws connecting the monitor to the stand and remove the stand as indicated Figure R 2 The monitor is now ready for mounting in an alternative manner 4 Connect the AC cord and signal cables to the back of the monitor Figure R 3 5 Reverse this process to re attach stand NOTE Use only VESA compatible alternative mounting method Ro TI NOTE Handle with care when removing monitor stand Non abrasive
21. r unstable cart stand or table as the monitor may fall causing serious damage to the monitor e When operating the LCD monitor with its AC 125 240V power supply use a power supply aord that matches the power supply voltage of the AC power outlet being used The power supply cord you use must have been approved by and comply with the safety standards of your country Type HO5VV F should be used in Europe e In U K use a BS approved power cord with molded plug having a black 5A fuse installed for use with this monitor If a power cord is not supplied with this monitor please contact your supplier e Do not place any objects onto the monitor and do not use the monitor outdoors e The lamps in this product contain mercury Please dispose according to state local or federal law e Do not bend power cord e Do not use monitor in high temperature humid dusty or oily areas e Do not cover vent on monitor Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the monitor e lf the monitor has been exposed to rain or water e lf the monitor has been dropped or the cabinet damaged e If the monitor does not operate normally by following operating instructions e lf monitor or glass is broken do not come in contact with the liquid crystal and handle wit
22. such as cadmium mercury and lead RoHS compliance e Both product and product packaging is prepared for recycling e The brand owner offers take back options The requirements can be downloaded from our web site The requirements included in this label have been developed by TCO Development in co operation with scientists experts users as well as manufacturers all over the world Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labeling system started with displays in 1992 and is now requested by users and IT manufacturers all over the world About 50 of all displays worldwide are TCO certified Technology for you and the planet For more information please visit www tcodevelopment com English 14 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material
23. surface Figure R 1 Figure R 2 Figure R 3 Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm Please use the attached screws 4pcs as shown in the picture when installing To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor The LCD monitor shall only be used with an approved arm e g GS mark Replace screws Thickness of Bracket Arm 2 0 3 2 mm Tighten all screws Specifications 4 SCREWS M4 MAX depth 7 0 mm If use other screw check depth of hole ey n Weight of LCD assembly 4 2 kg MAX English 7 Controls OSD On Screen Display control buttons on the front of the monitor function as follows 1 Basic function at pressing each key At No OSD Showing OSD Shortcut to Bright adjust Shortcut to Volume adjust Input signal select showing window window At OSD showing Go to Adjustment stage Cursor goes to left Cursor goes to right Icon selection stage At OSD showing Go to Icon selection stage Adjust value decrease or Adjust value increase or Reset operation Adjustment stage Cursor for adjust goes to left Cursor for adjust goes to Mute off on switch on Volume right adjustment window 2 OSD structure Main Menu Icon Select Main Menu Adjust oO Press o TE
24. tness setting CONTRAST Adjusts the image brightness in relation to the background AUTO CONTRAST Adjusts the image displayed for non standard video inputs AUTO ADJUST Automatically adjusts the Image Position the H Size and Fine setting LEFT RIGHT Controls Horizontal Image Position within the display area of the LCD DOWN UP Controls Vertical Image Position within the display area of the LCD H SIZE Adjusts the horizontal size by increasing or decreasing this setting FINE Improves focus clarity and image stability by increasing or decreasing this setting COLOUR CONTROL SYSTEMS Five colour presets 9300 7500 sRGB USER NATIVE select the desired colour setting COLOUR RED Increase or decreases Red The change will appear on screen COLOUR GREEN Increase or decreases Green The change will appear on screen COLOUR BLUE Increase or decreases Blue The change will appear on screen TOOL Selecting TOOL allows you to get into the sub menu FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings The 1 2 RESET button will need to be held down for several seconds to take effect Individual settings can be reset by highlighting the control to be reset and pressing the 12 RESET button EXIT Selecting EXIT allows you exit OSD menu sub menu English 9 Sal H La He D n O LANGUAGE OSD control menus
25. tosh systems do not require a Macintosh cable adapter es al Macintosh i e Cable Adapter not included Figure A 1 Figure A 2 Figure A 3 English 5 3 To attach the Cable management cover Insert the tabs of the Cable management cover into the holes of Stand neck and slide the Cable management cover downward into place Figure A 4 NOTE Please confirm that the tabs are completely secure 4 Connectall cables to the appropriate connector on the back of the monitor Figure B 1 Connect the Headphone not included to the appropriate connector at the rear side of the monitor Figure C 1 5 Connect one end of the power cord to the monitor and the other end to the power outlet Place the Video Signal Cable Audio cable and power cord to the Cable management cover Figure B 1 Cable management cover Figure A 4 NOTE Adjust position of cable that place under the Cable management cover to avoid damage for cable or monitor NOTE Please refer to Caution section of this manual for proper selection of power cord 6 Turn on the monitor with the front power button and the computer Figure C 1 AUDIO INPUT DVI D Input2 D Power Button S Cable management cover d Figure B 1 Figure C 1 Connect to Computer audio output 7 No touch Auto Adjust automatically adjusts the monitor to
26. ts all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync LCD175M L174F1 color monitor so as not to interfere with radio and television reception 1 The power supply cord you use must have been approved by and comply with the safety standards of U S A and meet the following condition Power supply cord Non shield type 3 conductor Plug shape a a U S A 2 Please use the supplied shielded video signal cable 15 pin mini D SUB to D SUB cable or DVI D to DVI D cable Use of other cables and adapters may cause interference with radio and television reception 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off
Download Pdf Manuals
Related Search