PocketWizard MiniTT1-Nikon
Contents
1. Auto Relay Mode A FlexTT5 radio in camera s shoe and connected with motor drive cord to P1 can receive a radio trigger and trigger the camera s motor drive which in turn triggers a remote flash The channel used for relay transmit is 1 higher than receive channel unless set differently via PocketWizard Utility Example f you taught FlexTT5 radio Standard channel 2 then relay transmit occurs on Standard channel 3 Press TEST on hand held trigger radio to begin relay sequence For Auto relay with remote i TTL Speedlights triggered by the remote camera an ACC cable is required For Auto Relay with manual flashes engage Basic Trigger Mode in the PocketWizard Utility any PocketWizard motor drive cable can be used Status LED Normal waiting for trigger operation short blink every 2 seconds Normal short blink color indicates Battery Level Green Good battery Amber Warning battery low Red Very low battery change immediately Steady red LED in sync with TEST indicates normal transmission Hold for 10 seconds to teach see Learn mode Short red blink in sync with trigger indicates normal reception Rapid red blinking when not triggering or half pressing camera indicates error condition Power off the unit reseat all connections and power back on RESET RESET A CHANNEL RESET To reset learned channels to channels last set in Utility hold TEST on power up LED blinks green twice to indicate reset Rel2. your MiniTT1 and FlexTT5 CLS i TTL for DSLRs only not for D TTL or film TTL PocketWizard com Warranty This PocketWizard product is covered under a two year limited manufacturer s warranty For warranty details and to register your product please go to www PocketWizard com support or contact your local PocketWizard Distributor Distributor contact information can also be found at www PocketWizard com To receive a copy of the two year limited manufacturer s warranty on this PocketWizard product e mail us at warranty lpadesign com or write to us at LPA Design Inc 21 Gregory Drive Suite 140 South Burlington VT 05403 United States of America Attn Warranty Frequency IMPORTANT US FCC Canada frequency radios are NOT compatible with CE frequency radios or Japan frequency radios and vice versa For more information on frequency please go to www PocketWizard com wheretobuy frequency 2010 LPA Design Inc All rights reserved Product features and specifications are subject to change without notice PocketWizard ControlTL MiniTT1 FlexTT5 PowerST4 AC3 AC9 HyperSync Plus Il and MultiMAX are either trademarks or registered trademarks of LPA Design Inc All other trademarks contained herein are the property of their respective owners For more information on this product including detailed features specifications and extended documentation go to www PocketWizard com US Patent 5 359 375 7 437 063 7 702 228 amp U
3. Mode Learn Mode is not required for normal operation of the radios IMPORTANT Hold radios at least 2 feet apart when teaching learning 1 Turn MiniTT1 or FlexTT5 radio ON and select channel to be taught C 1 or C 2 2 Press and hold TEST for several seconds until LED blinks amber then release TEST 3 Quickly press and hold TEST on teaching transmitting radio MiniTT1 FlexTT5 Plus II or MultiMAX When LED blinks green channel is learned Connected flash may trigger during Learn e 1 green blink Low Standard channel learned 1 through 16 including Plus 1 through 4 e 2 green blinks High Standard channel learned MultiMAX 17 through 32 e 3 green blinks ControlTL channel learned For remote i TTL systems teach MiniTT1 radio to be used as primary transmitter first then use it to teach all FlexTT5 units MiniTT1 and FlexTT5 radios send out both ControlTL and Standard triggers every time they are triggered For remote i TTL to function ControlTL channel must be learned If you see only 1 or 2 green blinks and you desire i TTL teach again with MiniTT1 or FlexTT5 radio Look for 3 green blinks to verify ControlTL is learned To teach all radios Standard channels use Standard transmitter as teaching radio for all learning radios including MiniTT1 radio to be used as primary transmitter To avoid inadvertent flashing turn OFF remote radios that have already been taught or have already had the channel set Other Functions
4. Nikon remote group zone via remote FlexT T5 zone switch PocketWizard channel is used instead of Nikon channel ISO aperture flash exposure compensation FEC and other settings will work with exposure normally via the PocketWizard ControlTL system Note Changes made on camera will not display on back of remote flash s LCD MiniTT1 Plus II MultiMAX Integrated or FlexTT5 connected to manual flash Remote flash with or without CLS i TTL flash on camera 1 Slide MiniTT1 Transmitter onto camera 2 If desired slide Nikon i TTL Speedlight onto MiniTT1 radio Speedlight must be in master mode as non master operation disables remote triggers 3 Make sure all your PocketWizard radios are on the same channel and take pictures normally Note Manual remote flashes are not calculated as part of the i TTL exposure Adjust your exposure or FEC to compensate accordingly Use PocketWizard Utility to engage HyperSync and explore faster than X sync shutter speeds Visit www PocketWizard com for more information Learn about the AC3 ZoneController PowerTracking and controlling your Speedlights and select studio flashes by reading the extended documentation for the following PocketWizard radios and accessories e AC3 ZoneController for Nikon e PowerST4 for Elinchrom e AC9 AlienBees Adapter for Nikon Learn Mode Channels can be set via PocketWizard Utility recommended or taught from any PocketWizard transmitter using Learn
5. PocketWizard Quick Guide Mini TT1 FIlexTT5 for Nikon 340 00 354 00 MHz US FCC IC 433 42 434 42 MHz CE UPDATE FIRMWARE Be sure ALL your PocketWizard ControlTL radios including this one are updated to the latest firmware for proper functionality Latest firmware version can be found at www PocketWizard com support downloads Please read this Quick Guide thoroughly before operating Visit www PocketWizard com support to download extended documentation and the PocketWizard Utility All information in this Quick Guide is subject to change Internal Antenna Battery Compartment on bottom Configuration Channel 1 Configuration Channel 2 Power Off Mini USB Connector on side TEST LEARN Button y Nikon style Hot Shoe Status LED Locking Ring A READ ME FIRST _ Mini USB Connector behind antenna Lanyard Loop Adjustable Antenna Batteries 2 AA IEC LR6 Zone Switch 1 4 20 Mount Configuration Channel 1 on bottom Configuration Channel 2 Power Off Nikon style Hot Shoe TEST LEARN Button Remote Flash Triggering Port Locking Ring Remote Camera Triggering Port Status LED CLS i TTL Basic Wireless CLS i TTL MiniTT1 FlexTT5 No flash on Camera 1 Slide MiniTT1 Transmitter onto camera 2 Slide Speedlight onto remote FlexTT5 Transceiver Set the Speedlight for standard i TTL mode not REMOTE or MASTER Repeat for each remote Speedlight All r
6. S and other patents pending PocketWizard LPF612 v2 2 MAKE IT POSSIBLE
7. ease TEST Advanced features set via Utility are retained RESET B FACTORY DEFAULTS To reset all advanced features and channels to FACTORY DEFAULTS hold TEST on power up for longer than 10 seconds When LED blinks green 4 times release e All settings may be configured using the PocketWizard Utility available from www PocketWizard com See the online extended documentation or the help text in the Utility for detailed descriptions of these settings Factory defaults Channel C 1 ControlTL channel 1 Standard channel 1 C 2 ControlTL channel 2 Standard channel 2 Use ControlTL for Rx Channel enabled For FlexTT5 Only Modeling Non Speedlight Modeling Light Mode Camera Wake Modeling Light Active Autotrack enabled Modeling Light Active 100 inactive due to Autotrack setting Modeling Light Sleep 10 Modeling Light Delayed Sleep enabled Modeling Light Delay After Camera Sleeps 30 secs Exposure Speedlight Flash Control Normal i TTL Non TTL Flash Control Auto ISO and Aperture Tracking Non TTL Exposure Compensation Value f stops 3 0 Sync Timing HyperSync Offset 0 microseconds High Speed Sync FP Flash Sync Disable Mode not enabled High Speed Sync FP Flash Sync Begins At 1 400 Flash Remote Beeper No Change On Wakeup Optical Trigger No Change On Wakeup Remote TTL Flash Sleep Mode disabled Flash Idle Time Out Mode disabled For FlexTT5 Only Misc Basic Tr
8. emote i TTL Speedlights will be treated as one zone of light 3 Make sure all your PocketWizard radios are on the same channel and take pictures normally This mode is like using the SU 800 in TTL Commander mode or the SB 800 or SB 900 as MASTER in Advanced Wireless Lighting TTL Mode with master flash cancelled and a remote group zone selected as TTL with 0 0 FEC Advanced Wireless CLS i TTL MiniTT1 gt FlexTT5 Flash on Camera 1 Slide MiniTT1 Transmitter onto camera 2 Slide Nikon SB 800 or SB 900 Speedlight onto MiniTT1 radio Set Speedlight for MASTER ON Enable remote groups zones per flash instructions Nikon SU 800 Wireless Speedlight Commander may also be used 3 Set remote FlexTT5 radio to desired remote group zone A B C using FlexTT5 zone switch 4 Slide Speedlight onto remote FlexTT5 Transceiver Set Speedlight for standard i TTL mode not REMOTE or MASTER Repeat for each remote Speedlight All remote i TTL Speedlights on the same group zone will be treated as one zone of light 5 Adjust flash output level compensation using MASTER Speedlight flash controls 6 Make sure all your PocketWizard radios are on the same channel and take pictures normally IMPORTANT Nikon Speedlights set to REMOTE ON and connected to remote FlexTT5 radios will not function properly as remotes You must be in normal i TTL mode for remotes to operate properly Turn off REMOTE or MASTER for your remote Speedlights Set desired
9. igger Mode disabled Force TTL Master Mode enabled Transmitter Only Mode disabled For FlexTT5 Only Bottom Shoe Disable Mode not enabled For FlexTT5 Only Specifications Specifications Trigger Delay 0 seconds faster than a wire when using compatible Nikon cameras approximately 900 microseconds in Basic Trigger Mode Batteries FlexTT5 2 x AA IEC LR6 60 hours MiniTT1 CR2450 or CR2354 e Approximately 30 hours of camera awake time varies with camera and Speedlight models e Low temperature operation and used batteries will have reduced battery life Always use fresh batteries when working in the cold e Basic Trigger Mode consumes the battery more quickly and is not recommended when using the MiniTT1 for Nikon on a Nikon camera Maximum FPS Up to 12 varies with camera i TTL usage reduces FPS Operating Temperature Above 15 C 5 F and below 50 C 120 F for FlexTT5 Above 12 C 109 F and below 50 C 120 F for MiniTT1 e Low temperature affects coin cell performance Always use fresh batteries in cold temperatures Storage Temperature without battery Above 30 C 22 F and below 85 C 185 F Compatibility This MiniTT1 FlexTT5 is compatible with most Nikon CLS i TTL compatible cameras and Speedlights Visit PocketWizard com for compatibility information specific to your cameras and Speedlights Some features may not be available or may be implemented via firmware updates to
Download Pdf Manuals
Related Search