JBL GTO1004 audio amplifier
Contents
1. JB GTO1004 OWNER S MANUAL BEDIENUNGS ANLEITUNG MODE D EMPLOI MANUAL DE USO HANDLEIDING MANUALE UTENTE ANV NDAR HANDBOK BRUGSVEJLEDNING OMISTAJAN K SIKIRJA PODR CZNIK UZYTKOWNIKA sinn BRIDGED FRONT lt INPUT BASS NN AUX OUT PUT BPS YN S forse X OVER L Installation Warnings and Tips e Disconnect the negative lead from your vehicle s battery At the installation sites locate and make a note of all fuel lines hydraulic brake lines vacuum lines and electrical wiring Use extreme caution when cutting or drilling in and around these areas Choose a safe mounting location away from moisture Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself Mount the amplifier using the supplied hardware Specifications 100W RMS x 4 channels 4 ohms and lt 1 THD e 150W RMS x 4 channels 2 ohms and lt 1 THD e THD 0 05 rated power 4 ohms Signal to noise ratio 85dB reference 1W into 4 ohms Signal to noise ratio 104dB referenc2. YA EN 55020 2002 1 2003 Klaus Lebherz Harman Consumer Group Inc Chateau du Loir Frankreich 8 07 Declaration of Conformity We Harman Consumer Group Inc 2 route de Tours 72500 Chateau du Loir France declare in own responsibility that the product described in this owner s manual is in compliance with technical standards EN 55013 2001 A1 2003 4 op EN 55020 2002 1 2003 2 Ms Klaus Lebherz Harman Consumer Group Inc Chateau du Loir France 8 07
3. OWNER S MANUAL Setting Input Level Turn all Input Level controls counterclockwise to 6V minimum With a dynamic music track playing turn the head unit s volume control to the 3 4 position Turn Front Input Level control clockwise until the music is so loud that it no longer sounds clear distortion is present in the output Turn Front Input Level contro counterclock wise gradually just until the music sounds clear once again Front Level input is now adjusted correctly 9 Adjust Rear Input Level control so that the level of the rear speakers is proportionate to the level of the front speakers according to your preference Setting the Crossover Crossover setting for 5 or larger full range speakers when no subwoofer is included in the system Crossover setting for full range speakers when a subwoofer is included in the system Crossover setting for subwoofers Crossover setting for systems that include separate mid bass speakers driven by the rear channels with the BP switch set to BP Note Acceptable frequency ranges are indicated in gray This product is designed for mobile applications and is not intended for connection to the mains A valid serial number is required for warranty coverage Features specifications and appearance are subject to change without notice www jbi com Harman Deutschland GmbH HiinderstraBe 1 74080 Heilbron
4. e rated power into 4 ohms e Frequency response 10Hz 100kHz 3dB Max power 600 watts CEA 2006A compliant Speaker Output Connectors Connect the speakers to these terminals observing proper polarity e Four channel operation Connect the front left speaker to the Front L and L terminals and the front right speaker to the Front R terminals Repeat for the rear speakers using the Rear L and L terminals and the Rear and R terminals Three channel operation Connect the stereo speakers to the Front terminals as above Connect the single speaker into which the amplifier s rear channels will be bridged to the Rear and Rear L terminals Two channel bridged operation Connect one speaker to the Front and Front L terminals Connect the other speaker to the Rear R and Rear L terminals e Minimum speaker impedance for stereo operation is 2 ohms Minimum speaker impedance for bridged operation is 4 ohms Fuses e Replace only with the same type and rating Power Input Connectors 12V Connect to the positive terminal of the vehicle s battery 8 AWG wire is recommended Install an appropriate fuse holder and fuse 75A minimum within 18 inches of the battery Make sure the wire is not damaged or pinched during installation Install protective grommets when routing wires through the firewall or other sheet metal e GND Connect to the vehicle s chassis Refer to t
5. he picture below Factory Bolt Ring Connector Ground Wire Note Remove any paint Star Washer below ring connector REM Connect to the Remote Out lead from the source unit or to a source of switched 12V ACC Aux Output Connectors RCA Summed nonfiltered pass through output Front right and rear right inputs are combined and sent to the right AUX output Front left and rear left inputs are combined and sent to the left AUX output Connect to the input of an additional subwoofer amplifier Front Input Connectors RCA Connect to the front RCA outputs from the source unit or signal processor Front Input Level Control Used to match the front input level of the amplifier to the output level of the source unit See for the adjustment procedure Front Crossover Frequency Control e 12dB octave crossover variable from 32Hz to 320Hz See for the adjustment procedure Front Crossover Filter Selector e LPF Select for subwoofer s e FLAT Select for full range speakers when no subwoofer will be used in the system HPF Select for midrange speakers full range speakers when a subwoofer is used in the system Rear Bass Boost Control Set the Bass Boost control according to your preference being careful not to apply enough boost to damage your speaker s Rear Band Pass BP Switch If you will use the rear channels to drive a pair of separate mid bas
6. n Telefon 07131 480 0 www jbl audio de 2007 Harman International Industries Incorporated Alle Rechte vorbehalten JBL ist eine Marke von Harman International Industries Incorporated eingetragen in den Vereinigten Staaten und oder anderen L ndern Teile Nr 6 010040 8 07 Harman Consumer Group Inc 250 Crossways Park Drive Woodbury NY 11797 www jbl com 2007 Harman International Industries Incorporated All rights reserved JBL is a trademark of Harman International Industries Incorporated registered in the United States and or other countries a Part No GTO10040M 8 07 Harman International Company 4 Harman Consumer Group Inc 2 route de Tours 72500 Chateau du Loir France 1 UY 55013 2001 1 2003 26 55020 2002 1 2003 Klaus Lebherz Harman Consumer Group Inc Chateau du Loir France 7 07 Konformitatserklarung Wir Harman Consumer Group Inc 2 route de Tours 72500 Chateau du Loir Frankreich erklaren in eigener Verantwortung dass das hier beschriebene Produkt folgenden Standards entspricht EN 55013 2001 A1 2003 l
7. s speakers place this switch in the BP position The front crossover frequency control will set the low pass filter frequency and the rear crossover control will set the high pass frequency In BP mode the rear crossover filter switch has no effect Only the front inputs should be used in BP mode Rear Crossover Filter Selector e LPF Select for subwoofer s e FLAT Select for full range speakers when no subwoofer will be used in the system HPF Select for midrange speakers full range speakers when a subwoofer is used in the system Rear Crossover Frequency Control e 12dB octave crossover variable from 32Hz to 320Hz e See the adjustment procedure Rear Input Level Control Used to match the input level of the amplifier to the output level of the source unit e See for the adjustment procedure Also used to adjust the level of the mid bass speakers when the BP switch is in the BP positon Rear Input Connectors Connect to the rear RCA outputs from the source unit or signal processor Not used when the BP switch is in the BP position Power On LED e Illuminated when the amplifier is Protect LED e Illuminated under of the following fault conditions battery over under voltage short circuit in speaker wires amplifier is too hot amplifier s output circuit has failed DC voltage is present the amplifier s output W amp I GTO1004 CAR AUDIO POWER AMPLIFIER
Download Pdf Manuals
Related Search