NEC NP600CM project mount
Contents
1. To adjust pitch forward and backward tilt Turn knob on back of mount as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn To adjust roll side to side tilt Turn knob on side of mount as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn ARROW INDICATES FRONT OF MOUNT KNOB FORPITCH ADJUSTMENT ACCESS SLOT FOR OPEN END WRENCH ALLOWS TIGHTENING OF WOOD SCREW F WITHOUT REMOVING PROJECTOR BACK OF MOUNT SCREW FOR YAW SWIVEL STOP REFERTOSTEP 2 INSTALLATION TO EXTENSION COLUMNS FIG 2 3 KNOB FOR ROLL ADJUSTMENT ye To prevent tampering with the pitch and roll adjustments Tighten the two tamper resistant security screws on the projector mount assembly using 4 mm security allen wrench B to lock the pitch and roll adjustments as shown below Note Tighten screws firmly but do not overtighten Overtightening can damage the mount CAUTION e Do not adjust pitch or roll while tamper resistant security screws are fully engaged e Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or damage may occur TOLOCK PITCH TIGHTEN TAMPER RESISTANT SECURITY SCREW A L gt La d SIDE VIEW 10 of 10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerle2. a E E A E avian ETT O E T A E A 10 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Before you start check the parts list to insure all of the parts shown are included Parts List Description projector mount assembly 4 mm security allen wrench 10 32 x 3 8 serrated washer head socket pin screw 10 32 x 1 4 socket pin screw flat washer 14 x 2 5 phillips hex head wood screw concrete anchor adapter plate M4 x 16 mm serrated socket pin screw retaining spacer 2 mm allen wrench 055 2803 560 9646 520 2151 520 2196 540 1078 5S 1 015 C04 590 0097 055 2869 510 2087 590 2009 560 1097 PO PD PO PD S Disengage connection block from projector mount assembly A by unscrewing captive screw and sliding out connection block as shown CONNECTION BLOCK CAPTIVE SCREW 3 of 10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Installation to Extension Column Ceiling Plate NOTE Refer to accompanying instructions with ceiling plates sold separately for installing these models to 2 ceiling Screw projector mount assembly A onto extension column as shown in figure 2 1 NOTE For 3 4 extension columns reducer ACC 913 not included will be required as shown in figure 2 2 Tighten swivel stop screw against extension column flush
3. mount tube or reducer using 4 mm security allen wrench B as shown in figure 2 3 NOTE Swivel stop screw is used to jam against threads of extension column flush mount tube or reducer to prevent any excess movement of projector mount assembly A Do not overtighten screw overtightening screw will damage threads making it difficult to separate products Skip to step 3 1 1 2 EXTENSION 3 4 EXTENSION COLUMN p COLUMN SOLD SEPARATELY SOLD SEPARATELY ULLISTED EXT OR ADJ SERIES ACC 913 J NOTULLISTED x SOLD SEPARATELY l l l ARROW ARROW INDICATES INDICATES FRONT OF FRONT OF MOUNT MOUNT fig 2 1 1g 2 2 ee L_____ F i 7 CMJ 455 l SOLD SEPARATELY SWIVEL STOP SCREW fig 2 3 4of10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Installation To Wood Joist Ceilings A WARNING Tighten wood screws so that projector mount assembly is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power e Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the studs The use of an edge to edge stud finder is highly recommended Place projector mount assembly A on ceiling as a templ
4. NEC NEC Display Solutions of America Inc Installation and Assembly Manual Custom Ceiling Mount for NEC NP400 NP500 NP500W and NP600 Projectors Model NP600CM Maximum Load Capacity 50 Ib 22 7 kg Features e ImageLock alignment prevents picture sag or drift e Wrench access slot for easier flush mount installations e Exclusive aluminum track quick release 1 of 10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 NOTE Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings con tained in this Installation Sheet If you have any questions regarding any of the instructions or warnings call Peerless customer care at 1 800 729 0307 This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Never exceed the Maximum Load Capacity Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holdi
5. ate and mark the center of the two mounting holes Make sure that the mounting holes are in the center of the wood joist Drill two 5 32 4 mm dia holes to a minimum depth of 2 5 64 mm Attach projector mount assembly A with two 14 x 2 5 6 mm x 65 mm wood screws F and two flat washers E as shown in figure 2 4 or figure 2 5 depending on joist orientation Tighten wood screws F using 3 8 10 mm socket wrench phillips screwdriver or 10mm open end wrench until projector mount assembly A is firmly attached Skip to step 3 ACCESS SLOT FOR OPEN END WRENCH ALLOWS TIGHTENING OF WOOD SCREW F WOOD JOIST WITHOUT REMOVING PROJECTOR WOOD JOIST FRONT OF MOUNT fig 2 4 fig 2 5 5 of 10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Installation to Concrete Ceilings A WARNING Tighten wood screws firmly but do not overtighten Overtightening can damage the screws greatly reducing their holding power e Never tighten in excess of 80 in Ib 9 N M template and mark the center of the two mounting holes Drill two 1 4 6 mm dia holes to a minimum depth of 2 5 64 mm Attach projector mount assembly A using two concrete anchors G two flat washers E and two 14 x 2 5 wood screws F as shown in fig 2 6 and 1 2 and 3 right Tighten wood screws F using 3 8 10 mm sock
6. e additional man power or mechanical lifting equipment to safely handle placement of the screen QO Slide connection block with projector into projector mount assembly A as shown Tighten captive screw to secure projector to projector mount assembly A ARROW INDICATES FRONTOF MOUNT FRONT OF ie MOUNT A A CONNECTION BLOCK pp CAPTIVE SCREW IMPORTANT For security installations insert one 10 32 x 1 4 socket pin screw D through projector mount assembly A and into connection block as shown in detail 1 Tighten screw using 4mm security allen wrench B A CONNECTIONBLOCK 9of10 ISSUED 08 05 08 SHEET 056 9008 1 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Projector Alignment To adjust yaw swivel for wood stud concrete ceiling and threaded rod mounting applications Loosen wood screws F if flush mounted to wood joists page 5 or concrete ceilings page 6 or loosen locknuts on threaded rods page 7 until projector mount can be rotated Rotate mount to desired position and retighten screws or locknuts To adjust yaw swivel for extension column applications Loosen screw on projector mount assembly A indicated below until projector mount can be rotated Rotate mount to desired position and retighten screw
7. et wrench phillips screwdriver or 10mm open end wrench until projector mount assembly A is firmly attached 2 Place projector mount assembly A on ceiling as a NOTE It is the responsibility of the installer to verify that the ceiling will safely support the combined load of all attached hardware and components Skip to step 3 e Concrete anchors are not intended for attachment to concrete ceiling covered with a layer of plaster drywall or other finishing material If mounting to concrete ceiling covered with plaster drywall is un concrete ceiling G avoidable plaster drywall up to 5 8 thick must be Tighten all fasteners counterbored as shown below If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer INCORRECT CORRECT 2 concrete ie concrete oa i Sean CUTAWAY VIEW CONCRETE CEILING 6 of 10 Visit the Peerless Web Site at www peerlessmounts com ISSUED 08 05 08 SHEET 056 9008 1 For customer care call 1 800 865 2112 or 708 865 8870 Installation to Threaded Rod Thread two 1 4 20 hex thin nylon insert locknuts not included on two 1 4 20 threaded rods not included to the desired height of projector mount assembly Attach projector mount assembly A to the two 1 4 20 threaded rods using two 1 4 20 hex
8. ng power See suggested torque values where applicable within these instructions This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury CAUTION e Itis the responsibility of the installer to ensure that the projector is properly ventilated Tools Needed for Assembly stud finder edge to edge stud finder is recommended phillips screwdriver drill 1 4 bit for concrete surface 5 32 bit for wood studs open end wrench level Table of Contents Pans Mle ee ee ee a a Installation to Extension Columns Ceiling Plate ccccceeccceeeeeeeeeeeeeeeeeceaeeeeceeeeeeeaaeeeceaaaeesecaeeeeseaeeeeseaaeeseeeeeeeeaeees 4 Installation to Wood Joist Ceilings sissisodan onian dinaan N i aaia SAAT VAa EANA UNa AE AAEE naaa ISNA niwa 5 Installation to Concrete CeilINGS 2 0 ccecceccenceeeceneeeeeeeeeeeeeaaeeeceaaeeeecaeeeeseaaeeeecaaaeeseeaeeeeseeeeeecaaaeeseaeeeeseseeeesiaeeseeueeeeeeeees 6 Installation to Threaded ROS c ceceecceeeeneeeceeneeeeeeeeeeeeeeaeeeeeeaeeeeceeeeeeeeaaeeseeaaeeeeceeeeeseaaeesscaaeeeseaeeeeseaeeessaaeeseeueeeseeaeees 7 Attaching Adapter Plate to Projector eccccceceeeencneeee eee eenne tees ee eeaaaeeeeeeeeeaaaeeeeeeeeeaaaeeeeeeeeeaaaeeeeeeeeeaaeeeeeseeeaaeeeeeeeeeaaes 8 Attaching Adapter Plate to Projector MOUNM cccceeeeeeecteeeee eee eeenneeeeeeeeeaaeeeeeeeeeaaaeeeeeeeeeeaaaeeeeeseeeaaeeeeeseeeiaeeeeeeeeeaaes 9 aea a
9. ss Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 2008 Peerless Industries Inc All rights reserved Allother brand and product names are trademarks or registered trademarks of their respective owners
10. thin nylon insert locknuts as shown in figure 2 7 or figure 2 8 1 4 20 THREADED ROD NOT INCLUDED 1 4 20 THREADED ROD NOT INCLUDED 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED ARROW ARROW INDICATES INDICATES FRONT OF FRONT OF MOUNT MOUNT 1 4 20 HEX THIN 1 4 20 HEX THIN 2 8 NYLON INSERT NYLON INSERT LOCKNUT LOCKNUT NOT INCLUDED NOT INCLUDED Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 or 708 865 8870 Attaching Adapter Plate to Projector Align shoulder on connection block opposite notch in adapter plate AA Attach adapter plate to connection block from projector mount assembly A using two 10 32 x 3 8 serrated sreepIORics washer head socket pin screws C as shown in figure 3 1 Tighten using 4 mm allen wrench B PCE ee CONNECTIONBLOCK SHOULDER Flip projector upside down and attach adapter plate AA using three serrated socket pin screws BB and retain ing spacers CC as shown below Tighten using 4 mm allen wrench B NOTE Retaining spacers CC go between the projector and adapter plate AA 8 of 10 ISSUED 08 05 08 SHEET 056 9008 1 For customer care call 1 800 865 2112 or 708 865 8870 Visit the Peerless Web Site at www peerlessmounts com Attaching Adapter Plate to Projector Mount A WARNING Do not lift more weight than you can handle Us
Download Pdf Manuals
Related Search