Digi Hubport/4c
Contents
1. East Minnetonka MN 55343 declares that the product Hubport Installation Guide 90000664 Rev D Page 4 Product Hubport 4 Model Numbers North America International 301 1010 04 301 2010 04 Product Name Hubport 4c Model Numbers North America International 301 1010 45 301 2010 24 Product Name Hubport 4c DC Model Numbers North America International 301 1010 42 301 2010 42 Product Name Hubport 7 Model Numbers North America International 301 1010 07 301 2010 07 Product Name Hubport 7c Model Numbers North America International 301 1010 75 301 2010 27 Product Hubport 7c DC Model Numbers North America International 301 1010 72 301 2010 72 Product Name Hubport 4 DC Model Numbers North America International 301 1010 30 301 2010 30 Product Name Hubport 7 DC Model Numbers North America International 301 1010 70 301 2010 70 Product Options All conforms to the relevant EU Directives listed here EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC R amp TTE 1999 5 using the relevant section of the following EU standards and other normative documents EMC EN55022 Class B 2006 EN55024 1998 A1 A2 EN61000 3 2 2000 A2 EN61000 3 3 1995 A1 A2 Safety EN 60950 2001 The following summarizes the specifications and requirements for EN55024 EN55022 Class B amp CISPR 22 Class B emission and immunity tests If the actual test levels are higher or different t2. of the publication For U S Government use Any provision of this document and associated computer programs to the U S Government is with Restricted Rights Use duplication or disclosure by the government is subject to the restrictions set forth in subparagraph 1 1 of the Rights in Technical Data and Computer Software clause of DFARS 52 277 7013 For non U S Government use These programs are supplied under a license They may be used disclosed and or copied only as supplied under such license agreement Any copy must contain the above copyright notice and restricted rights notice Use copying and or disclosure of the programs is strictly prohibited unless otherwise provided for in the license agreement Federal Communications Commission FCC Regulatory Information USA only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be d
3. table above if used in the U S and Canada or power supply with similar rating and approved by your local safety code if it is used elsewhere 1 Some units may be equipped with pigtail connection Follow the polarity markings on the cable 2 For polarity on Hubports with threaded locking connector use center positive as follows Le 3 For polarity on all other Hubports use the following _ D Hubport Installation Guide 90000664 Rev D Page 2 Installing Hubport Drivers For Windows 98 2000 and XP Users After following the instructions described in Connecting Your Hubport in the previous section installation will be complete For Windows NT 4 0 Users Because Microsoft does not support USB in NT4 0 Digi International supplies a set of USB drivers that will be installed along with the necessary Hubport drivers NOTE You must install the drivers using an account that has administrative privileges To install the USB stack and Hubport drivers 1 Insert the Edgeport Driver CD Version 2 60 or above into your CD ROM drive 2 When the welcome dialog appears click the Install Driver button Once the driver installation program has begun follow the on screen instructions 3a If you are installing drivers for the first time An Information dialog informs you that the installation was successful After clicking OK the installation is complete 3b If you are replacing existing Edgeport drivers Follo
4. Hubport USB HUB Installation Guide Models Hubport 4 Hubport 7 lc Models Hubport 4c Hubport 7c Hubport 4c DC Hubport 7c DC www digi com Table of Contents to HS Connecting Your Hubport rrrrrnnnrrrrrrrrrnnnnnnnnnnnrrrrrrrnnnnn Installing Hubport Drivers rrrrrrrrrrrrrrrrnnnnnnnnnnnrrrrrrrnnnnn Interpreting the System Status Regulatory Other Introduction to Hubs Thank you for purchasing the Hubport a self powered Universal Serial Bus USB hub designed to provide a convenient and effective means of bringing USB connectivity to your PC server or laptop The Hubport also delivers the potential of Digi International s Edgeport USB to Serial RS 232 expansion module Hubs critical components in the USB architecture are wiring concentrators that enable the attachment of multiple devices thus converting a single attachment point into multiple attachment points USB architecture allows a cascaded multiple hub configuration with certain power limitations explained later in this section See figure 1 PC Host Hub port OOO ewe tot Edge port joystick mouse Figure 1 Example ofa Typic al Hub Configuration Each hub has an upstream port connecting to the host and multiple downstream p
5. etermined by turning the equipment off and on the user is encouraged to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver Connect the equipment into an outlet that is on a circuit different from the receiver Consult the dealer or an experienced radio TV technician for help Warning The connection of a non shielded interface cable to this equipment will invalidate the FCC Certification for this device FCC Regulation Part 15 Declaration of Conformity DoC This device complies with the requirements of the Code of Federal Regulations listed below FCC Title 47 CFR Part 15 Class B for a digital device Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation Department of Communication DOC Notice Canada only This Class B digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la Classe B respecte toutes les exigences du R glement sur le mat riel brouiller du Canada European Community CE Mark Declaration of Conformity DOC According to ISO IEC Guide 22 and EN 45014 Manufacturer s Name Digi International Manufacturer s Addr 11001 Bren Road
6. han required these levels are listed in the appropriate tables EN55022 Test Specification Requirement EN55022 Radiated Class B Emissions Conducted CISPR 22 Class B Emissions EN 55024 Test Specification Requirement 55024 Electrostatic EN61000 4 2 2 4 direct contact Discharge 2 4 kV and 8 air insulated surfaces 2 4 kV HCP amp VCP indirect Radiated EN61000 4 3 3 V m 80Mhz Immunity 1000Mhz amp mod 1kHz sine wave at 80 Electrical Fast EN61000 4 4 0 5kV IkV A C Transient Burst 0 5kV EN61000 4 5 0 5kV IkV 1kV Conducted EN61000 4 6 3Vrms 150Mhz to Immunity 80Mhz amp mod IkHz wave at 80 Magnetic EN61000 4 8 1 A m Not Applicable Immunity Voltage Dips amp Interrupts EN61000 4 11 gt 95 10ms 30 500ms amp gt 95 Ssec reduction at rated voltage European Contact Digi International Joseph von Fraunhofer Str 23 44227 Dortmund GERMANY 49 23 1 9747 0 UL CSA Safety Information This device complies with the requirements of following safety standards below UL 1950 3rd edition Hubport Installation Guide 90000664 Rev D Page 5 CSA No 950 July 2006 Quality Manager Austin Texas Digi International 11001 Bren Road East Minnetonka MN 55343 digi info digi com www digi com Corporate Headquarters 952 912 3444 877 912 3444 Fax 952 912 4952 Digi Europe 49 23 1 9747 0 Digi Hong Kong 852 2833 1008 D
7. igi North America 877 912 3444 Hubport Installation Guide 90000664 Rev D Page 6
8. mbered 1 4 or 1 7 each indicate that the corresponding port is powered For Hubport Models The green Power Light located next to the power connector indicates that the Hubport has power The green Port Status Lights numbered 1 4 or 1 7 each indicate that the attached USB device is connected and enumerated Hubport Installation Guide 90000664 Rev D Page 3 Regulatory amp Other Information 2006 Digi Digi International the Digi logo the Digi Connectware logo Edgeport and Hubport are either trademarks or registered trademarks of Digi International Inc in the United States and or other countries All other trademarks are the property of their respective holders Information in this documentation is subject to change without notice and does not represent a commitment on the part of Digi International Digi International provides this document as is without warranty of any kind expressed or implied including but not limited to the particular purpose Digi International may at any time make improvements and or changes to this documentation the product s and or program s described in this documentation Digi International assumes no responsibility of any errors technical inaccuracies or typographical errors that may appear in this documentation nor liability for any damages arising out of its use Changes are made periodically to the information herein these changes may be incorporated in new editions
9. orts connecting to downstream devices possibly including other hubs A hub can detect attachment and detachment of downstream devices and enable and monitor the distribution of the power to downstream devices via their integral hardware and the operating system Each USB device reports its power requirements to the operating system which then enables and disables the device as a function of its power requirements and the amount of available power High powered devices typically need to be connected to a self powered hub such as the Hubport which obtains power from its external power supply and provides up to 500 mA for each downstream port Only low powered devices such as a mouse can be connected to a bus powered hub which obtains power from its upstream host and provides up to 100 mA for each downstream port Due to the limited available power for bus powered hubs cascading two bus powered hubs is an illegal topology and devices connected to the second hub will not function USB specifications limit the connection of a bus powered hub to a self powered hub or host only All Hubports except the Hubport 4c in bus powered mode operate as self powered hubs and are not affected by this limitation According to the USB Specification the maximum limit of hubs cascaded in series cannot exceed five In other words you may have a maximum of five hubs between any device and the host This does NOT mean that the maximum number of hubs in a system i
10. s five Indeed up to seven hubs can be connected parallel at any given level You must tally both external and embedded hubs when counting downstream hubs Hubport Installation Guide 90000664 Rev D Page 1 Specifications USB Powering Power Product Downstream Method Ports Requirements Hubport4 s m 4 SVDC 2A osses 2 af Variable 5 5 30VDC 15W Hubport 4c DC Self 50001326 20 Yes 50001326 21 Hubport SVDC 3A gone SVDC 3A Hubport 7c DC Variable 10 28DC 24W Hubport 4c DC 50001326 22 50001326 23 Self 4 5VDC 2A kar Variable 10 28VDC 0 15W Connecting Your Hubport Type Type B Note that Windows NT 4 0 users must install the drivers before connecting Hubport To connect the cables included with your Hubport 1 Plug one end of the power supply into the back of your Hubport and the other end into an AC outlet 2a To connect your Hubport to a PC plug the Type A end of the USB cable into one of the PC s USB A slots and the Type B end of the USB cable into the back of the Hubport OR 2b To connect standard USB device to your Hubport plug the Type end of the USB cable into the Hubport and the Type B end into the device t USB 2 0 High Speed is not supported by Windows 98 Power to this product may be supplied by UL Listed Direct Plug In Power Unit marked Class 2 with minimum rating listed in the Specifications
11. w the on screen instructions Note that before beginning the installation of the drivers all applications with open ports must be closed and all USB devices unplugged If you Close all the applications and unplug all the USB devices then you will not need to reboot for the new drivers to take effect immediately If any applications are left open or USB devices plugged in you may choose to abort the installation or to continue and be required to reboot before the upgrade can take effect Follow the instructions described in Connecting Your Hubport in the previous section When finished with the instructions your new communication ports numbered sequentially following the existing ports in your system are ready Note that because Windows NT 4 0 15 not Plug and Play you will not see a pop up dialog box indicating that new hardware has been found You may verify correct installation with the USB Status Utility The USB Status Utility Viewer can be accessed by clicking the USB icon in your system tray or by clicking on Start Programs Digi USB USB Status Utility This utility lists all the USB devices installed on your PC and provides other relevant information for each device You may also use this utility to create a log file Interpreting the Status Lights For Hubport 4 and Hubport 7 The green System Status Light indicates that the USB ports are successfully set up and the Hubport is operating normally The green Port Status Lights nu
Download Pdf Manuals
Related Search