APC NetShelter SX
Contents
1. ns1548b Airflow Management Blanking Panel AR8136BLK Qty 10 AR8136BLK200 Qty 200 Covers an empty vertical enclosure space to maintain proper airflow 19 inch 1 U cable pass through with brush strip AR8429 Assists with containing air in the enclosure and providing an aesthetic solution for cable routing NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 21 Accessory Part Number Description KoldLok raised floor grommet AR7720 Qty 10 AR7730 Qty 10 AR7740 Qty 10 Designed to seal openings in new raised floor cutouts prior to the installation of communications or power cabling 22 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Cable Routing and Cable Management The NetShelter SX Networking Enclosure has cable access openings on its roof sides and bottom Four vertical cable managers and two Vertical 0 U Accessory Channels are included with the enclosure and APC offers a variety of other cable management accessories Adjusting the Vertical 0 U Accessory Channels The vertical 0 U accessory channels provide toolless mounting capabilities for APC Rack Power Distribution Units PDUs and APC cable containment brackets They also provide tie off locations for cables The factory default position for2. 42U 48 U ns1845a NetShelter SX AR7510 For NetShelter SX 42 U 23 inch EIA Networking 42 U a Mounting Rails 750 mm wide enclosures AR3140 and AR3340 only the mounting rails accommodate 23 in rack mountable equipment Ech Ss ns0814a Fixed shelf 50 lb AR8105BLK Cantilever fixed shelf to enable the mounting of a monitor or other equipment into the rack environment or to allow cable pass through from the front to rear of the enclosure NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Airflow Management Caution Improper airflow could damage installed components Installing Airflow Management Panels 1 U and 3 U foam airflow management panels help isolate hot air and prevent it from entering the cold aisle Install airflow management panels in the channel along the right vertical mounting flange next to inactive equipment such as patch panels The left side of the enclosure does not require panels Note To ensure proper airflow into networking switches keep open the networking switch air intake areas as well as the inlets of the side airflow duct kit Note Install the airflow management panels before
3. D patch panel d 2 0 B 8 B g L 0 U data AR8457 Installs in a vertical distribution 0 U accessory panel channel Holds four data distribution cables for a total of 24 ports 24 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Accessory Part Number Description 19 inch AR8602 1U Routes cables horizontal horizontally on the cable AR8600 2 U front or back of the organizers 19 inch EIA AR8601 enclosure 2 U double sided AR8603 2 U high density Cable AR7710 Contains cables containment Qty 6 along the vertical 0 U brackets accessory channel Installs without tools Side panel AR7305 For a NetShelter SX with access Qty 2 Networking 42 U holes 1070 mm deep enclosure AR3140 only Allows cable pass through to adjacent enclosures Openings contain a brushes to restrict airflow E Zero U AR7711 Zero U multi accessory purpose accessory mounting mounting bracket for bracket 1 U and 2 U equipment including Rack PDUs NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 25 Accessory Part Number Description Vertical cable manager AR7717 Qty 4 Installs in the vertical mounting flanges and in the vertical 0 U accessory channels The vertical cable manager has smooth plastic cable guides at U increments to allow patch cords to enter and exit
4. Installation and Customization Manual APC Limited Factory Warranty The limited warranty provided by American Power Conversion APC in this Statement of Limited Factory Warranty applies only to Products you purchase for your commercial or industrial use in the ordinary course of your business Terms of Warranty American Power Conversion warrants its products to be free from defects in materials and workmanship for a period of five years two years in Japan from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its sole discretion any such defective products This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way Repair or replacement of a defective product or part thereof does not extend the original warranty period Any parts furnished under this warranty may be new or factory remanufactured Non transferable Warranty This warranty applies only to the original purchaser who must have properly registered the product Product may be registered at http www warranty apc com Exclusions APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user s or any third person s misuse negligence improper installation or testing Further APC shall not be liable under the warranty for unauthorized att
5. Reversing the Front Door You can reverse the front door so the door is hinged on the opposite side Required tools Torx T30 2 Phillips wrench provided in hardware bag 1 Remove the handle s Il 2 Disconnect the ground wire and then remove the door ns1758b NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual ns1752b 3 Remove and reinstall the hinges on the enclosure frame 5 Reinstall door and reconnect the ground wire ns1824a 6 Remove and reinstall the latch and washer oriented as shown The washer is rotated 90 degrees from its original orientation and the latch is rotated 180 degrees ns1766b NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 11 12 7 Reinstall the handle on the door ns1779b 8 Remove and reinstall the APC nameplate at the location shown 241 3 mm 9 5 in 335 02 mm 13 19 in ns1253b NetShelter SX Networking Enclosure Unpacking Instal
6. firm level surface in an open area Inspect for visible signs of shipping damage If you detect shipping damage contact APC Customer Support using the contact information on the back cover of this manual 2 See the label on the packaging to determine where to cut the wrapping Using sturdy shears or a utility knife carefully remove the plastic stretch wrap surrounding the enclosure 3 Remove the four cardboard corner protectors 4 Remove and retain the two pallet mounting brackets with mounting hardware that anchor the enclosure to the shipping pallet Use a 13 mm wrench not provided Note Save the pallet mounting brackets if you plan to bolt the enclosure to the floor 5 With one person on each side of the enclosure carefully roll it toward the rear of the pallet until the rear casters clear the back edge of the pallet Continue to slide the enclosure until the rear casters touch the floor 6 While one person carefully tips the enclosure slightly away from the pallet have the other person pull the pallet away from the enclosure Set the enclosure gently on its casters Warning Use caution when moving an empty enclosure on its casters the enclosure may be unstable when pushed or pulled from the side Push the enclosure from the front or back when moving it on its casters For extra stability load 158 kg 350 lbs of equipment into the bottom of the enclosure before moving it on its casters 2 NetShelter SX Networking Enclosur
7. 0 in Ib Do not ground one enclosure to another enclosure in a cascading style ns1617b 14 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Equipment Installation Adjusting Vertical Mounting Flanges Vertical mounting flanges come factory installed on the enclosure in the proper position for use with rack mountable equipment that has a depth of e 558 8 mm 22 in for a 1070 mm deep enclosure 749 3 mm 29 5 in for a 1200 mm deep enclosure The mounting flanges are adjustable towards the front or the rear of the enclosure to accommodate different rails or equipment with other depths The flanges can be adjusted to be as close as 279 4 mm 11 in or as far apart as 819 mm 32 25 in for a 1070 mm deep enclosure 959 mm 37 75 in for a 1200 mm deep enclosure ns1453a To adjust a vertical mounting flange Warning To avoid personal injury or damage to N the enclosure perform this procedure without any equipment installed on the mounting flanges 1 Remove the cable manager from the front left vertical mounting flange ns1561a NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 15 16 2 Use the Torx T30 2 Phillips wrench provided to loosen but not remove the three Torx Sc
8. R ANY FORM OF INDIRECT SPECIAL CONSEQUENTIAL OR PUNITIVE DAMAGES ARISING OUT OF THE USE SERVICE OR INSTALLATION OF THE PRODUCTS WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT IRRESPECTIVE OF FAULT NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBLY OF SUCH DAMAGES SPECIFICALLY APC IS NOT LIABLE FOR ANY COSTS SUCH AS LOST PROFITS OR REVENUE LOSS OF EQUIPMENT LOSS OF USE OF EQUIPMENT LOSS OF SOFTWARE LOSS OF DATA COSTS OF SUBSTITUANTS CLAIMS BY THIRD PARTIES OR OTHERWISE NO SALESMAN EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY WARRANTY TERMS MAY BE MODIFIED IF AT ALL ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL DEPARTMENT Warranty Claims 32 Customers with warranty claims issues may access the APC worldwide customer support network by visiting http www apc com support Select your country from the country selection pull down menu Open the Support tab at the top of the web page to obtain contact information for customer support in your region NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests www apc com Corporate Headquarters Connect to loc
9. RENDA ETE 6 Enclosure Installation Moving the Enclosure llleeeeeen nnn 7 Leveling the Enclosure lleeeeeeeeeennl 8 Joining Enclosures vest o E we eee Fae FREUE EY eee EC 9 Reversing the Front Door anssanaasannnnnnnnnannne 10 Securing the Enclosure 000 eee cece ence cece eens 13 Grounding the Enclosure 000 cece eee eee 14 Equipment Installation Adjusting Vertical Mounting Flanges eee eens 15 Installing Equipment ge een Gea eek eee eee 18 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Airflow Management eeeeeeeeeeen Installing Airflow Management Panels 20 Airflow Management Accessories sess 21 Cable Routing and Cable Management Adjusting the Vertical 0 U Accessory Channels 23 Removing Vertical Cable Managers 000 cee eee eee 23 Cable Management Accessories llu 24 Specifications 4 oie eie ei aes APC Limited Factory Warranty ii NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Introduction The American Power Conversion APC NetShelter SX Networking 750 mm wide enclosures are high quality enclosures for storag
10. al cable managers or can be used in the middle of the enclosure for cable tie off In addition keyholes are provided to mount one vertical Rack PDU per organizer Ege Me DLT TT E gaol 7 247225 7 Ca Ee ee EE 24 E7 2 ETT BETA ns1754b NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 27 Accessory Part Number Description Vertical fiber AR8443A The vertical fiber organizer organizer provides a method to manage fiber cabling within an enclosure and mounts toollessly into the vertical 0 U accessory channel Fiber AR8444 Can be mounted organizer Qty 4 toollessly to the CH spools vertical fiber E organizer or a ar vertical 0 U CH accessory channel i fi ch aSN cg EN d di fin Aa dH 718 28 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Accessory Part Number Description Toolless AR8621 Includes ten 457 mm hook and Qty 10 18 in hook and Loop cable loop black cable manager straps that install in the square mounting holes of vertical 0 U accessory channels or vertical mounting flanges ns1855a NetShelter SX Networking Enclosure Unpacking Instal
11. alized APC Web sites for specific countries each of which provides customer support information www apc com support Global support searching APC Knowledge Base and using e support Contact the APC Customer Support Center by telephone or e mail Local country specific centers go to www apc com support contact for contact information For information on how to obtain local customer support contact the APC representative or other distributors from whom you purchased your APC product O 2010 APC by Schneider Electric APC the APC logo and NetShelter are owned by Schneider Electric Industries S A S American Power Conversion Corporation or their affiliated companies All other trademarks are property of their respective owners 990 3548B 001 11 2010
12. e Unpacking Installation and Customization Manual Component Identification Enclosure 090006000 e Adjustable vertical 0 U accessory channel Removable rear split doors Key for doors and side panels Removable side panels with locks Enclosure frame Adjustable leveling feet Hardware bag see page 4 Airflow management kit see page 4 0000000 Casters Removable and reversible front door APC nameplate Vertical cable managers Mounting flange cable manager Vertical mounting flanges Roof NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Hardware bag contents Plastic cup M6x 16 M5x12 Cage nuts 7 mm hole washers 60 Phillips slot screws 4 60 plugs 4 screws 60 m v Torx T30 42 Phillips wrench Cage nut tool Airflow management kit 3 U foam airflow management panel 12 included 1 U foam airflow management panel 4 with 42 U enclosures AR3140 and AR3340 14 included with the 48 U enclosure AR3347 4 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Removing and Reinstalling Side Panels Roof and Doors Side Panels Roof NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Doors Q Note Doors self align on hinge pi
13. e of industry standard EIA 310 19 inch rack mount hardware which includes servers and voice data networking internetworking and APC power protection equipment This manual covers the three APC NetShelter SX Networking 750 mm wide enclosures NetShelter SX Networking 42 U 750 mm wide 1070 mm deep enclosure AR3140 NetShelter SX Networking 42 U 750 mm wide 1200 mm deep enclosure AR3340 NetShelter SX Networking 48 U 750 mm wide 1200 mm deep enclosure AR3347 Safety Warnings and Cautions Observe all Warnings and Cautions in this manual plus the following Tip Hazard This equipment is easily tipped Use extreme caution when unpacking or moving Heavy Use at least two people to unpack the enclosure N Warning To avoid damage or injury do not use the roof as a walkway NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Unpacking the Enclosure Disclaimer American Power Conversion is not responsible for damage sustained during reshipment of this product Receiving inspection Inspect the package and contents for shipping damage and make sure that all parts were sent Report any damage immediately to the shipping agent Report missing contents damage or other problems immediately to APC or your APC reseller Please Recycle The shipping materials are recyclable Save them for later use or dispose of them fs appropriately Procedure 1 Move the shipping pallet to a
14. empts to repair or modify wrong or inadequate electrical voltage or connection inappropriate on site operation conditions corrosive atmosphere repair installation start up by non APC designated personnel a change in location or operating use exposure to the elements Acts of God fire theft or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been altered defaced or removed or any other cause beyond the range of the intended use THERE ARE NO WARRANTIES EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE OF PRODUCTS SOLD SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH APC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE APC EXPRESS WARRANTIES WILL NOT BE ENLARGED DIMINISHED OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND PURCHASER S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES APC WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 31 IN NO EVENT SHALL APC ITS OFFICERS DIRECTORS AFFILIATES OR EMPLOYEES BE LIABLE FO
15. es e e m u Unpacking Installation iut and Customization Sr Manual NetShelter SX Networking Enclosure U S Patent No 7 293 666 B2 Date of Patent November 13 2007 4 wa Au A S T A SLE Es This manual is available in English on the enclosed CD Dieses Handbuch ist in Deutsch auf der beiliegenden CD ROM verf gbar Este manual est disponible en espa ol en el CD ROM adjunto Ce manuel est disponible en francais sur le CD ROM ci inclus Questo manuale disponibile in italiano nel CD ROM allegato ALY a TIVO ARREA CD ROM 2 5 TERNET Instrukcja obs ugi w j zyku polskim jest dost pna na CD O manual em Portugu s est dispon vel no CD ROM em anexo lanHoe PyKOBOACTBO Ha pycckom A3bIKe WMeercs Ha nipATniaraeMoM KOMTTaKT AMCKe Bu kullanim kilavuzunun T rkce s alaxakte g nder len CD er s nde mevcuttur EAT AM BR HS CD ERIT ER A SCHR AS Contents Introd CEIOTEG ai arsenic if reu Veo aci Pa C RR av vel QU SMS Safety Warnings and Cautions Unpacking the Enclosure Component Identification Removing and Reinstalling Side Panels Roof and DOOFS eege Neue dee ee Side lt TEE EE 5 ROOF us vuestros rb Nd ee e i wa ee PUR Vd a Gee etes ut ees 5 DOO jg B
16. in an organized manner TAPPA Vertical cable organizer for NetShelter 0 U accessory channel AR8442 Qty 2 Eliminates cable stress by organizing cable layout within the rear channels of the enclosure Uses 0 U space within the enclosure Consists of two pieces of equal size When stacked both pieces span the entire height of the enclosure Two pieces can be installed side by side in the vertical 0 U accessory channel Can be used in any APC enclosure 26 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Accessory Part Number Description NetShelter SX AR7502 Installs in the 42 U vertical Qty 2 enclosure along the cable side braces Provides organizer toolless mounting capabilities for APC NetShelter SX AR7572 Rack Power 48 U vertical Qty 2 Distribution Units cable PDU and APC organizer cable containment brackets Provides tie off locations for cables f Da NetShelter SX AR7511 For NetShelter SX 42 U narrow Qty 2 Networking 42 U vertical 0 U enclosures AR3140 B cable and AR3340 only R organizer The narrow vertical A 0 U accessory channel complements the standard vertical 0 U accessory channel by offering additional cable management options The narrow channel can be used in the front of the enclosure to mount fiber cable spools and vertic
17. installing any cabling ol Rigged ERR E Ek n M LEER a olio EE kai ob oko GRE E Kok Eoo EGER E DEGERE TUE KEE EIE EEG PER Dn ERE Eo AGRE PGR Se KEE LIEGE RHR Sdn ERE BR PR Se KE dae RGR Hideki oko EIE EEG EGER EU EE TE KEE EGER E BEIGE TE GRIGG Ad EIE EGER DEGERE TUE KEE LIEGE RR KKH ERE BE PR EGER EE KEE LIEGE RHR DECIR TUE ERE GRE PE Oe GRR GAGE EK KEE Riga Hideki GEER GRE EH KEE oboe E GE E EECH KR SH o EE ps U Al i a Pia So ia Si Ela Si A ns1497a Eg 2 H o gong E z a g ZS Sea S305 ns1562a Sm a Cua cm a cm a cma cm ll a cmm ES 20 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Airflow Management Accessories Accessory Part Number Description Side Airflow Duct Kit ART715 The NetShelter Side Airflow Duct Kit is intended for use with Cisco Catalyst 6509 6509 E and 6513 Switches and Cisco MDS 9509 and 9513 Multilayer Switches For networking switch applications the Side Airflow Duct Kit allows for improved cable management solutions while maintaining adequate airflow and separation of hot and cold aisles to cool switches The Side Airflow Duct Kit maintains separation of hot and cold aisles via ducts and baffle panels a ene mma Sm Sm ene mm Al a m 5 n zm i
18. lation and Customization Manual 29 Specifications Height Width Depth Net weight Total open area front door Total open area rear door Open area per U front door Open area per U rear door Perforation pattern percentage Percent of perforated area front Percent of perforated area rear Clearance for wiring between front door and vertical mounting flange Weight rating static load Weight rating rolling AR3140 1991 mm 78 40 in 42U 750 mm 29 53 in 1070 mm 42 13 in 155 95 kg 343 10 Ib 788 972 mm 1 222 91 in 866 920 mm 1 343 73 in 18 787 mm 29 12 in 20 645 mm 32 i 69 88 96 238 76 mm 9 40 in 1361 kg 3 000 Ib 1021 kg 2 250 Ib AR3340 1991 mm 78 40 in 42U 750 mm 29 53 in 1200 mm 47 24 in 161 36 kg 355 00 Ib 788 972 mm 1 222 91 in 866 920 mm 1 343 73 in 18 787 mn 29 12 in 20 645 mm 32 in 69 88 96 216 9 mm 8 5 in 1361 kg 3 000 Ib 1021 kg 2 250 Ib Lower the leveling feet if the static weight is over 1020 58 kg 2 250 Ib 30 AR3347 2258 mm 88 90 in 48 U 750 mm 29 53 in 1200 mm 47 24 in 185 45 kg 408 00 Ib 900 417 mm 1 395 65 in 989 243 mm 1 533 33 in 18 787 mm 29 12 in 20 645 mm 32 in 69 87 96 216 9 mm 8 5 in 1361 kg 3 000 Ib 1021 kg 2 250 Ib NetShelter SX Networking Enclosure Unpacking
19. lation and Customization Manual Securing the Enclosure For additional stabilization secure the enclosure to the floor Use fastener locations on the outside or inside of the enclosure and choose from the accessories shown below brackets the enclosure Part NA Accessory Number Description Bolt down kit AR7701 Attaches to rack and floor internally or externally to provide additional stability without blocking cable access NetShelter SX AR7700 Attaches externally to the stabilizer plate rack and floor to provide additional stability Pallet bolt down provided with Attaches to rack and floor internally or externally to provide additional stability without blocking cable access With the appropriate mounting hardware meets IBC CBC seismic requirements NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual ns1780b Grounding the Enclosure Each enclosure should be grounded directly to the building ground using one of the designated grounding locations two M6 threaded inserts at the top or bottom of the enclosure Use a Common Bonding Network Jumper kit for example Listed KDER Panduit RGCBNJ660PY or equivalent Use paint piercing washers between ground terminal and enclosure frame or remove paint on frame under ground terminals per NEC NFPA 70 Article 250 12 Torque screws to 6 9 N m 6
20. nclosure from becoming top heavy Do not extend equipment on sliding rails until you have installed three or more pieces of similar sized equipment or until you have installed the stabilizer plate or bolt down brackets Do not extend more than one piece of equipment on sliding rails at a time To install rack mount equipment in the enclosure 7L 1 Review the equipment manufacturer s installation instructions L 2 Locate the top and bottom U space on the vertical mounting rails HE Every third hole on the mounting rails is numbered to indicate the middle of a U space 1U e 3 Install the cage nuts on the interior of the vertical mounting rail C then install the equipment KE How to install a cage nut sC ns0014a Warning To ensure equipment installs N securely install cage nuts with tabs x wi engaging the left and right sides of the square hole Do NOT install cage nuts with tabs engaging the top and bottom of the square hole Note To remove a cage nut squeeze the sides to release it from the square hole ns1788a 18 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Equipment Installation Accessories Accessory Part Number Description Recessed rail kit AR7508 for a Use the recessed rail kit to 42 Uenclosure install equipment that has a different mounting depth AR7578 for a from the other equipment 48 Uenclosure in the enclosure 15 U
21. ns when properly reinstalled 1 With the door at a 90 degree angle to the front of the enclosure position the door over the hinge pins ns1750b 2 Use slight pressure to pull the door away from enclosure then lower the door ns1751b 3 Connect the ground wire ns1752b NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Enclosure Installation Moving the Enclosure Caution To avoid damaging the enclosure and causing a tip hazard make sure the leveling N feet are up before moving the enclosure Casters The enclosure can be moved on its casters with up to 1021 kg 2 250 lbs of equipment installed Tip Hazard Use caution when moving an empty enclosure on its casters Push the enclosure from the front or back only the enclosure may be unstable if pushed or pulled from the side For extra stability load 158 kg 350 Ibs of equipment into the bottom of the enclosure before moving it on its casters Eye bolts The enclosure can be lifted using eye bolts with up to 567 kg 1 250 Ibs of equipment installed Use M10 eye bolts with a shoulder rated for 181 kg 400 lbs ns0882b NetShelter SX Networking Enclosure Unpacking In
22. rews 3 Lower the three flat brackets and move the mounting flange to the desired location NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual ns0977b ns0717c 4 To align the vertical mounting flanges properly note the symbol for example a diamond visible through one of the three holes on the top of the flange and ensure that the same symbol is visible through the corresponding hole at the bottom of the flange Only one symbol is visible at a time through any of the holes In the factory standard position diamonds are visible Note Vertical mounting flanges adjust in 6 mm 1 4 in increments Vertical mounting flanges placed across from each other must have the same visible symbol ns0718c 5 When the vertical mounting flange is in the proper location at the top middle and bottom raise the flat bracket until the teeth in the bracket engage fully with the teeth in the side brace and then tighten the Torx screws NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Installing Equipment f Warning To prevent the enclosure from tipping over after equipment installation e Make sure you have secured the enclosure to the floor before installing equipment Install the heaviest equipment first toward the bottom of the enclosure to prevent the e
23. stallation and Customization Manual Leveling the Enclosure Required tools CAE Phillips screwdriver Level 13 mm open ended wrench 803 513C Warning The leveling feet at the corners provide a stable base if the floor is uneven N but they cannot compensate for a badly sloped surface To adjust the leveling feet after equipment has been installed use the 13 mm open ended wrench not provided na1572a 8 NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual Joining Enclosures Enclosures can be joined with or without side panels installed to provide for alignment and some stability N Caution Joining enclosures provides limited stability to the enclosures 1 Remove the front and rear doors 2 Choose between 24 in centers or 600 mm centers see the detail view below 3 Align the enclosures and join them using one M5 x 12 flat head screw provided in the hardware bag per bracket two brackets for the front and two brackets for the rear 4 Reinstall the doors ns1594b Accessory Part Number Description 42 U 48U AR7600 Fills the gap between the Baying Trim enclosures spaced on 24 in centers providing finished look NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 10
24. the vertical 0 U accessory channels is in the rear of the enclosure but you can move them anywhere along the side braces in a similar manner to the mounting flanges See Adjusting Vertical Mounting Flanges on page 15 If needed the channels can be removed completely Additional vertical 0 U accessory channels can be ordered from APC see Cable Management Accessories on page 24 for details Removing Vertical Cable Managers You can remove vertical cable managers if needed to meet your cable routing needs If removed vertical cable managers can be reinstalled in the vertical 0 U accessory channels NOSSA ns1511c NetShelter SX Networking Enclosure Unpacking Installation and Customization Manual 23 Cable Management Accessories Accessory Part Number Description U data AR8451 Holds four data g distribution shown distribution cables T panel for a total of 24 ports p z gon g 2 U data AR8452 Holds eight data Boo SE distribution distribution cables 8 panel for a total of 48 ports g Wl CAT 6 Patch CAT6PNL 24 24 port RJ45 to 110 Panel shown 568 A B color coded 7 Ls patch panel 3 ol a T s n gt 5008 CATGPNL 48 48 port RJ45 to 110 d Fe 568 A B color coded s d
Download Pdf Manuals
Related Search