AirLink AICAP650W surveillance camera
Contents
1. Cable Modem N Local Computer Wireless Router IP Camera Section 2 Installing the Setup Wizard Step 1 Insert the provided CD and wait for the autorun screen to appear Step 2 Click on Install Setup Wizard Install Setup Wizard Install IP View Pro View User Manual View Quick Installation Guide Install Adobe Acrobat Browse CD Exit Note If the autorun screen does not appear automatically go to Start gt Run gt and type D Setup Setup exe where D is the letter of your CD drive and click OK Step 3 Click Next InstallShield Wizard Welcome to the InstallShield Wizard for Setup Wizard The Install hield Wizard will install Setup Wizard on your computer To continue click Next lt Back n Cancel Step 4 Click Yes to accept the License Agreement InstallShield Wizard License Agreement Please read the following license agreement carefully Press the PAGE DOWN key to see the rest of the agreement End User License Agreement NOTICE TO USER THIS IS A CONTRACT BY INSTALLING DOWNLOADING OR USING THIS SOFTWARE YOU ACCEPT THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT 1 Intellectual Property Rights The software is copyrighted The software is also protected by United States Copyright Law and International Treaty provisions Trademarks shall be used in accordance with accepted trademark practice including identification of trademark ownerl s name Do you accept2. IP Address DHCP Static IP IP Address 192 168 1 240 Subnet Mask Default Gateway Primary DNS Secondary DNS Back Next Enter the SSID of your wireless router in the SSID field and click Next If you have encryption enabled for your wireless network follow the subsequent steps otherwise skip to Wireless Interface SSID default No Encryption WEP Key Format Code key WPA Share key l Back Next WEP Step 9a Select the appropriate Key Format and enter the same WEP Code Key as your wireless router Click Next and skip to Step 10 SkyIPCam IP Camera Wireless Interface SSID No Encryption WEP Key Format ASCII 64 bit Code key WPA Back Next Exit WPA Step 9b Enter the same WPA Share Key as your wireless router and click Next SkyIPCam IP Camera Wireless Interface SSID default No Encryption WEP Key Format ASCII 64 bit v Code key Share key WPA Back Next Exit Step 10 Verify that all the fields are correct and click Restart to save the settings and reboot the camera Zia SkyIPCam Re IP Camera Admin ID admin Password AAKAAOK IP Address 192 168 1 240 Subnet Mask 255 255 255 0 SSID default WEP Key Share key Primary DNS 192 168 1 1 Secondary DNS 0 0 0 0 The Setup Wizard has completed Click on Back to modify your settings Click Restart to save your current setting and reboot the Inte
3. all the terme of the preceding License Agreement If you choose No the setup will close To install Setup Wizard you must accept this agreement InstallShield Mo Step 5 Click Next to accept the default Destination Folder InstallShield Wizard Choose Destination Location Select folder where Setup will install files Setup will install Setup Wizard in the following folder To install to this folder click Nest To install to a different folder click Browse and select another folder Destination Folder C Program Files 4nrLink 101 4lPCamera Browse InstallShield lt Back New Cancel Step 6 Click Finish to complete the installation InstallShield Wizard InstallShield Wizard Complete Setup has finished installing Setup Wizard on your computer lt Back Fish Cancel Using the Setup Wizard Step 1 Go to Start gt All Programs gt AirLink101 IP Camera Setup Wizard gt AirLink101 IP Camera Setup Wizard Windows XP Professional a oie fg AirLink101 IP Camera Setup Wizard Sy GirLink 101 IP Camera Setup Wizard Documents Uninstall Setup Wizard Settings Search Help and Support RUM Log OFF Shut Down Step 2 Select the IP Camera you want to configure from the list and click on the Wizard button SkyIPCam IP Camera tetworkingsolutians Wizard Mac Address Current IP Address Device Name 00 6i 07 71 03 A3 192 166 1 240 ALI APESO WW Search Web Confi
4. PRat nx 101 Ax A S S DMAIL SkylPCam650W Model AICAP650W Quick Installation Guide Getting Started This Quick Installation Guide only provides the basic instructions For more detailed information please refer to the User s Manual in the supplied CD Caution The IP Camera is designed for indoor use only Direct exposure to sunlight may cause permanent damage to the CMOS sensor When operating in extremely bright environment an iris lens or sun visor is recommended to protect the IP Camera System Requirement Before you begin please review the following system requirement OS Windows 98SE ME 2000 XP e CPU 650MHz or above 2 4 GHz recommended when monitoring multiple cameras simultaneously e Memory Size 256MB e Resolution 1024x768 or above Web Browser Internet Explorer 5 0 or above Step 1 Align the camera stand with the bottom part of the camera Then secure the camera stand with the screw Step 2 Connect one end of a network cable to the IP Camera and connect the other end to one of the LAN ports of the wireless router E Connect to LAN e Connect to Power Step 3 Power on the IP Camera by connecting one end of the supplied power adapter to the power jack of the Camera and connecting the other end to an electrical outlet Step 4 Verify that the LED lights on the Camera are lit If not verify that all the connections are secure and try again e o gt DSL
5. camera at the desired location a fo us DSL Cable Modem Wireless Computer Wired Computer Wireless Router IP Camera To access the camera from a wireless computer open the web browser Internet Explorer enter the IP Address of the camera default is 192 168 1 240 and press Enter Fie Edit View Favorites Q lx Address 192 168 1 240 Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Theoretical maximum wireless signal rate based on IEEE standard 802 119 specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction mix of wireless products used radio frequency interference e g cordless telephones and microwaves as well as network overhead lower actual data throughput rate Specifications are subject to change without notice All products and trademarks are the property of their respective owners Copyright 2006 AirLink1017M
6. ctiveX controls marked safe For scripting Disable Enable O Prompt fate mld lt i Reset custom settings Reset custom settings Lok IIL cancel Step 4 Close Internet Explorer and re launch the Web Config screen SkyIPCam IP Camera Wizard Ya E HoH e 00 gl Of 7105 45 192 168 1 240 AICAPESON ala tanita Search r Web Config ri About EEE Exit Step 5 Click on the ActiveX Control prompt A PAN TILT LAN Camera Microsoft Internet Explorer Fie Edit View Favorites Tools Help sek Ned x z f po Search SIP Favorites 4 Address http 192 168 1 240 finde html i This site might require the Following Actives control PlugLite3 Class from Airlink Plus Information Bar Help Step 7 Click on Install to install the ActiveX Control Internet Explorer Security Warning Do you want to install this software Name XPlugLite3 Class Publisher Airlink Plus More options Install Bont Install While Files from the Internet can be useful this file type can potentially harm vour computer Only install software From publishers you trust What s the risk Step 8 After the ActiveX Control is installed you should see the live video on Internet Explorer Wireless Connection After you have configured the IP Camera from the Setup Wizard you may unplug the Camera s network cable from the wireless router and place the
7. g About Step 3 If the Camera s default IP address is on a different subnet the following message will appear Click Yes to continue If you do not receive this message skip to Step 6 AirLink101 IP Camera Setup Wizard Your camera s IP Address may be invalid Please change your cameras IP Address to match your network settings or you will be Unable to connect to the camera Would you like to change the IP Address now Cancel Enter amp 4dmin ID admin Enter Password E E OK Cancel Step 5 The Wizard will automatically generate an IP address for the camera if this address is not in use by any other device in your local network click OK Otherwise enter an available IP address ex 192 168 x 240 and click OK Change IP Address Change IP IP Address 192 168 2 240 Subnet Mask 255 255 255 0 Gateway 192 168 2 1 The above mentioned suggestion Address does not guarantee its usability In some cases may still be with the address conflict of IP of other equipment OK Cancel Enter admin for both the Admin ID and Password field and click Next Optionally you can change the password by checking on the Change box and entering the new password Set up an Admin ID and Password to secure your camera Click Next to continue If you need to change the Camera s IP address because another network device is already using the same address you can assign a new address here and click Next Set
8. low the steps below to enable and install Activex Step 1 Open Internet Explorer and go to Tools gt Internet Options A PAN TILT LAN Camera Microsoft Internet Explo File Edit View Favorites ie Help O Back x Mail and Mews Pop up Blocker d Manage Add ons Address Synchronize Windows Update Sun Java Console Step 2 Select the Security tab and click on Custom Level Internet Properties General Privacy Content Connections Programs Advanced Select a Web content zone to specify its security settings lt 0O Internet Local intranet Trusted sites Restricted sites Internet This zone contains all Web sites you haven t placed in other zones Security level for this zone Cuztom Custom settings To change the settings click Custom Level To use the recommended settings click Default Level Custom Level Default Level Step 3 Verify the following settings are selected Click OK when done Automatic prompting for ActiveX controls Enable Download signed ActiveX controls Prompt e Run ActiveX controls and plug ins Enable Security Settings cd Ed Security Settings Settings Settings gi Initialize and script ActiveX controls not marked as safe A Disable B Enable Prompt script behaviors j Run Actives controls and plug ins Administrator approved Disable Enable Download signed Actives controls Promp Disable m Script A
9. rnet Camera Video Server e e Back Restart Viewing Images Note The following steps describe how to view images from within the same local area network as the IP Camera To view images from an external network such as the Internet please refer to the User s Manual on the provided CD for further instructions Step 1 At the Setup Wizard select the desired camera from the list and click on the Web Config button SkyIPCam IP Camera Wizard Mac Addre er PaO ore Je e Mane 006107 7103 43 192 168 1 240 AICAPESOW a Search fe Web Config About Exit Step 2 Enter the password for the camera Default is admin and click OK CameraServet User name admin _ Remember my password Step 3 The welcome page appears If you did not change the default password you will be prompted to do so before accessing the camera Camera Server Welcome Achrurustrator password setup Hew password Hew password contin Step 4 The Main menu along with the live video appears on screen The IP camera is ready for use now Camera LL 2006 06 18 20 24 25 Any Admin mode peg Setting menu Note ActiveX must be installed and enabled on your Web Browser Internet Explorer before you can view the live videos For more information please refer to the next section Section 5 Enabling and Installing Activex If no image appears on the web browser Internet Explorer fol
Download Pdf Manuals
Related Search