Tecnoware FGCEVO3 uninterruptible power supply (UPS)
Contents
1. TECNOWARE Dos oer S EVO Uninterruptible Power Supply EVO 1 0 EVO 2 0 EVO 3 0 USER S MANUAL INDEX SECURI TY NOTI CE INTRODUCTI ON UPS EVO 1 MAIN CHARACTERI STI CS 2 EXTERNAL DESCRIPTION FRONT PANEL REAR SIDE 3 RUNNING OPERATIONS SWITCHING ON LINE MODE BATTERY MODE LOW BATTERY AND AUTOMATIC RESTART LOAD TEST 4 INSTALLATION INSTRUCTIONS RECEIPT OF UPS PLACEMENT FIRST START UP COMPUTER I NTERFACE 6 TECHNICAL CHARACTERI STI CS SUGGESTI ONS FOR A CORRECT USE MAI NTENANCE BATTERY MAINTENANCE SAFETY FOR THE OPERATOR ANOMALIES AND TROUBLESHOOTING 9 FIGURES Copyright 2006 TECNOWARE s r l All rights reserved All trademark are property of their respective owners TECNOWARE s r l www service tecnoware com This manual has been printed and edited by TECNOWARE s r l November 2006 Edition version 3 0 User s manual 1 page page page page page page page page page page page 11 12 13 14 15 17 UPS EVO SECURI TY NOTI CE Read this manual carefully before installing and using TECNOWARE EVO Uninterruptible Power Supply which will be referred to as UPS from hereafter The UPS must be used only by properly trained personnel To ensure correct and safe operation it is necessary that operators and maintenance personnel observe the general Safety Standards as well as the specific instructions included in this manual Risk of electric shock d2. 180 degrees and plug in the power receptacle again I NVERTER led This led blue is on when the Inverter is regularly working BATTERY led This led blue is on when the UPS is working in BATTERY mode during a blackout or overvoltage brownout BYPASS led This led blue is on when the UPS is working in BYPASS mode the AC input line is connected directly with the UPS outlets FAULT led This led red is turned on whenever the UPS detects a FAULT condition and needs a technical intervention as soon as possible User s manual 5 UPS EVO LOAD LEVEL led bar Refer figure 2 Front Panel The led bar has 6 leds 5 leds are blue and one led is red This bar indicates the output power percentage LOAD LEVEL proportional to the number of switched on leds The greater the load the more LED indicators will light on There are the following LOAD LEVEL percentages 0 20 only one led is on led13 21 40 two leds are on led13 and led12 41 60 three leds led13 12 and 11 61 80 four leds are on led13 12 11 and 10 81 100 five leds are on led13 12 11 10 and 9 The OVERLOAD red led led8 is on to warn of an OVERLOAD condition BAT LEVEL led bar Refer figure 2 Front Panel The led bar has 6 leds 5 leds are blue and one is yellow This bar indicates the battery capacity percentage BAT LEVEL proportional to the number of switched on leds The higher the battery
3. EN 36VDC 4 SN 5 lt x vd ON Ds 0 g S X Ka SS A MANUAL BYPAS XN x X X 7 N 2 SN 7 B S M NS S 215 8 x Figure 3 Rear side On the left EVO 1 0 on the right EVO 2 0 and EVO 3 0 Grounded AC Input socket Input Circuit Breaker Grounded output socket Grounded power output socket EVO 2 0 and EVO 3 0 Computer I nterface RS 232 RJ 11 RJ45 I N OUT plugs Slot for external batteries connector Dty contacts board Slot for SNMP adapter Manual BYPASS switch 10 Remote ON OFF contacts 11 EPO Emergency Power OFF 5 20 User s manual 24 MONTHS WARRANTY valid in all UE countries TECNOWARE S r l guarantees the product for a period of 24 months from the original date of purchase The date of purchase is proved with the receipt of account released by the authorised reseller which clearly indicates the date in which the product was sold and the product identification code model and serial number Upon request of Technical assistance a copy of your receipt must be surrendered This guarantee implies free reparation or free substitution of any products parts or components which result faulty due to defective manufacture In such case the transportation costs are covered by the guarantee service In the event of irreparable fault or should the same malfunct
4. line for example blackouts brownouts overvoltages micro interruptions which often cause damage to hardware and software During a power failure EVO continues supplying adequate AC power with a true sinewave to all connected devices by its internal battery and by its DC AC converter Inverter Under normal AC line condition EVO provides an automatic output voltage regulation by the Rectifier and Inverter blocks and filters out frequently occurring electrical disturbances high voltage transients spikes interferences etc thus protecting the devices connected to its outlets EVO protects the devices from accidental overload or Inverter fault by an AUTOMATIC BYPASS that directly connects the AC input line with its outlets EVO is supplied with an RS 232 communication port and USB port which can be used to signal to a generic processor or computer the absence of mains condition or the end of autonomy condition This permits to carry out an automatic data saving operation during a long black out with the most spread Operating Systems Windows Linux Novell etc Furthermore the communication ports permit EVO to communicate with the computer transferring various measurements such as input output voltage battery voltage output power frequency and can also be programmed for automatic operations such as switching ON OFF in a preset time WARNING Please read this manual before using EVO because it contains important safety in
5. EVO requires at least 20 cm of unobstructed space all around in order to be properly ventilated Do not obstruct ventilation holes and do not insert objects or liquids in the ventilation holes Do not place any object on top of the EVO UPS Do not pour liquids flammable gases or corrosive substances near or on the unit UPS EVO 12 User s manual FI RST START UP The first start up procedure is very simple We advise you to follow the steps below explained 1 Through the supplied cable connect the UPS to the AC line outlet It is mandatory to ground the outlet according to the Safety Standards Carefully check the grounding make sure that the utility power is available and that its range falls within the UPS specifications 2 Switch the UPS ON and see that it operates correctly Check that the UPS does not signal any sort of anomaly Wait for the correct switching to LINE mode and make sure that the cooling fans are set in motion Leave the UPS in LINE mode for at least 8 hours in order to completely recharge the batteries 3 Switch the UPS OFF 4 Connect the devices to be supplied to the UPS output sockets Then put all the main switch of each device in the ON position 5 Restart the UPS and see that it operates correctly wait for the UPS to start working properly in LINE mode and that no overload signal or any other form of anomalies are present Then make sure that all equipments switch on correctly In case of Overload immed
6. TTERY mode EVO indicates the LOW BATTERY condition whenever the battery reaches a charge level allowing connected devices to operate for approximately one more minute The UPS warns the user of this LOW BATTERY condition by increasing the acoustic alarm signal there is an acoustic signal every second and by turning on the yellow led of the BAT LEVEL If the AC utility power is not restored within one minute of this condition the UPS will automatically switch OFF This will protect the batteries from a sudden deep discharge EVO stops supplying output power will deactivate the alarm signals and will place itself in a stand by mode When the AC utility power is restored the UPS automatically switches ON and returns to work in LINE mode After a complete discharge the UPS will need around 8 hours to completely recharge the batteries The recharge is automatic in either two ways The UPS is ON and running in LINE MODE e The UPS is OFF and connected to an AC input line LOAD TEST EVO indicates the output power percentage by the LOAD LEVEL bar The output power is proportional to the number of the leds switched on as described into the chapter External description The UPS warns of an OVERLOAD condition by lighting up the red OVERLOAD led at the top of the LOAD LEVEL bar In LINE mode EVO has the capability to accept an overload from 11096 to 15096 for about 30 seconds the UPS indicated the OVERLOAD condition by lighting up the red O
7. VERLOAD led and by an acoustic signal every second and after it switches automatically to the BYPASS MODE In LINE mode EVO switches automatically to the BYPASS mode as soon as the overload is higher than 15096 Once the requested power is back within range EVO switches automatically to the LINE mode again In BATTERY mode EVO has the capability to accept an overload from 11096 to 15096 for about 30 seconds the UPS indicated the OVERLOAD condition by lighting up the red OVERLOAD led and by an acoustic signal every second and after it turns automatically off In BATTERY mode EVO switches automatically off as soon as the overload is higher than 15096 After removing the cause for the overload condition in order to switch the UPS ON again it is necessary to press the OFF button in order to switch the UPS OFF Wait for a few seconds and then press the ON TEST ALARM button It is possible to carry out a LOAD TEST in the following way Make sure that UPS is working in LINE mode with all powered equipment switched ON and absorbing MAXIMUM POWER e Press the ON TEST ALARM button for more than 1 second to start the TEST EVO begins operating in BATTERY mode The TEST is overcome if all equipments keep on working and if the UPS does not signal any anomalies overload or other After a few seconds the TEST is finished and the UPS returns in LINE mode We advise you to carry out the LOAD TEST periodically in order to check the UPS effi
8. VO 6 User s manual EMERGENCY POWER OFF EPO Remote Button EPO The EVO models have the EPO Emergency Power OFF connector 2 terminals connector on the rear This permits to immediately switch the UPS OFF from a distance in case of emergency To use EPO function is very simple it is sufficient to connect an external switch to the EPO terminal see Figure 3 Rear Side if the switch is CLOSED the UPS works normally If on the contrary the switch is OPEN then the UPS turns OFF immediately To switch ON the UPS again it is necessary to close the EPO switch and then manually restart the UPS from the front panel The EPO terminals are isolated and do not need an external feeding voltage REMOTE ON OFF Remote Button ON Remote Button OFF The EVO models have remote ON OFF terminals connector on the rear side see figure 3 this permits to switch the UPS ON and OFF from a distance Using the ON OFF external button as described in the above picture the frontal panel button capacity can be used from a distance Evo is on pressing the OFF button connected to terminal 1 and 2 for at least 3 seconds EVO turns OFF EVO is off pressing the ON button connected to terminal 4 and 5 for at least 3 seconds EVO turns ON The remote ON function is disabled when the UPS is off and the AC input line voltage is not present User s manual 7 UPS EVO DRY CONTACTS BOARD ONAL Common Fault By
9. cally to BYPASS mode in consequence of accidental overload or Inverter fault thus protecting the supplied devices The BYPASS mode is characterized by The BYPASS led and LINE led switched on e The LOAD LEVEL and BAT LEVEL led bars switched on The UPS can be transferred in BYPASS mode even through a manual operation First of all it must be sure that the UPS is working properly in LINE mode On the rear side of the product see figure 3 it is positioned the manual BYPASS switch If this switch is in position ON BYPASS the UPS changes in BYPASS mode and indicates this condition with The BYPASS led and LINE led switched on All the LOAD LEVEL led bar switched on the red OVERLOAD and FAULT Leds switched on e Continuous acoustic alarm The UPS starts working again normally if it moves the switch in OFF NORMAL position Acoustic alarm stops immediately and the UPS effectuates then an operating SELF TEST during which the red FAULT and OVERLOAD Leds are switched on After some seconds more the BYPASS led is switched off and the INVERTER led is switched on this indicates that the UPS has started working normally in LINE mode During the above mentioned operations the devices powered by UPS will continue working regularly WARNING BYPASS operations must be carried out ONLY by qualified Technical personnel specialised and authorised by Tecnoware UPS EVO 10 User s manual LOW BATTERY AND AUTOMATIC RESTART In BA
10. capacity the more LED indicators will light on There are the following battery capacity percentages 100 8196 five leds on led15 16 17 18 and 19 e 80 61 four leds are on led15 16 17 and 18 60 41 three leds are on led15 16 and 17 e 40 21 two leds are on led15 and led16 e 20 096 only one led is led15 The LOW BAT yellow led led14 is on to warn of a LOW BATTERY condition during BATTERY mode REAR SIDE The following are located on the rear side see figure 3 1 Grounded AC Input power socket to connect the UPS to AC utility line by the supplied input cord 2 Input Circuit Breaker it goes off in overload or short circuit condition push the external 3 Grounded output socket for connecting equipments to be protected 4 Only EVO 2 0 and EVO 3 0 Grounded power output socket for connecting an output power line to supply all the equipments to be protected 5 RS 232 Computer Interface female connector 9 poles DB9 it is the interface port RS 232 to communicate with a computer 6 RJ11 RJ45 IN OUT plugs to protect and filter a phone line an ADSL or a LAN 7 Slot for external batteries connector to connect the UPS to an external Box Battery optional 8 Dry contact board Slot for SNMP adapter optional 9 Manual BYPASS switch to force the UPS into BYPASS mode see chapter Running Operations 10 Remote ON OFF contact 11 EPO Emergency Power OFF UPS E
11. ciency WARNING Make sure that the UPS never indicates OVERLOAD when running Do not connect a load greater than the rated nominal value on the UPS label see POWER specifications in the TECHNICAL CHARACTERISTICS chapter as this may damage the unit this case the warranty is void User s manual 11 UPS EVO I NSTALLATI ON NSTRUCTI ONS RECEI PT OF UPS Inspect the UPS upon receipt If the UPS has been damaged during shipment keep the box and packing material for the carrier Notify the carrier and dealer immediately Make sure the following is in the box e EVO UPS UPS output cable AC input power cord Phone cable User s manual UPSILON 2000 software for UPS management including CD rom and RS 232 cable User s manual We advise you to keep the original box in a safe place and use it in case the UPS needs to be sent to the service for maintenance PLACEMENT We advise you to place the EVO as close as possible to the AC input line and to the equipment that needs to be powered The UPS is designed to operate in protected environments for example offices This UPS should be installed indoors with adequate airflow and free of contamination Locate it in a clean and indoor environment free from moisture flammable liquids and direct sunlight In all circumstances see the TECHNICAL CHARACTERISTICS chapter for environmental specifications and check that the selected area meets these criteria
12. e internal specifications Before you go on to the next operations switch the UPS OFF and remove the UPS input voltage Check the Input Circuit Breaker Should it be snapped OFF position check if the UPS is overloaded then try to rearm the breaker by bringing it in the ON position keep it pressed e Check the feeding cable and all connections Equipments connected to the UPS do not switch ON Before you go on to the next operations switch the UPS OFF and remove the UPS input voltage Check the condition of every feeding cables and their right connection The UPS indicates OVERLOAD e Check which dispositives are feeding by the UPS and if it is really overloaded Bring the power request within the specifications and disconnect the dispositives that cause the overload The UPS autonomy is lower than the specified one Recharge the batteries for at least 8 hours and then check the autonomy again UPS EVO 16 User s manual WARNING Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded If the described anomalies shou
13. ed UPSILON 2000 software with RS232 cable SNMP INTERFACE Optional EPO EMERGENCY POWER OFF Included REMOTE ON OFF Included DRY CONTACTS BOARD Optional FILTERED PHONE PLUG Plug RJ 11 RJ45 included WARRANTY 2 years Technical data may change without prior notice UPS EVO 14 User s manual SUGGESTI ONS FOR CORRECT USE MAI NTENANCE EVO needs minimal maintenance throughout its lifetime WARNING Prior to achieve any check up or cleaning operations make sure that the UPS is switched off and that the mains voltage in the UPS input is switched off We advise to periodically check the mains input cable the output connections and to dust the ventilation holes Do not use liquids or detergents to clean the UPS Only use a humid cloth Before switching the EVO on make sure that it is perfectly dry If accidentally some liquid penetrates inside the UPS do not switch the UPS on and immediately consult authorised Technical Service BATTERY MAI NTENANCE The battery recharge is automatic when the UPS is ON and working in LINE mode The batteries are also recharged if the UPS is OFF and connected to the mains It is necessary to carry out a three monthly functioning test in BATTERY mode this will preserve the batteries in an excellent state and extend the life duration Leave the UPS in BATTERY mode until the end of autonomy condition is reached After which restore the i
14. formation for the operator in order to carry out a correct use of the unit This manual is related to the below EVO models e EVO 1 0 e EVO2 0 e EVO 3 0 In this manual the same for all 3 models EVO will simply be called UPS EVO is constantly being developed and improved consequently your unit may differ somewhat from the description contained in this manual User s manual 3 UPS EVO MAIN CHARACTERI STI CS EVO offers all the modern characteristics which guarantee maximum reliability and security UPS EVO Microprocessor control guarantees high reliability ON LINE double technology without transformer Pure Sinewave Output voltage regulation 2 Overload overheating and short circuit protection AUTOMATIC BYPASS to protect from accidental overload or Inverter fault MANUAL BYPASS through switch on the rear side Switching ON even with no mains condition Automatic protection in case of discharged batteries After a shutdown caused by the end of autonomy and when mains condition is restored there is an automatic SWITCHING On operation Automatic functioning test through a switch Automatic regulation to the input frequency 50 or 60 Hz Visual warnings by leds indicating operational mode and low battery overload and alarm conditions Dry contact board optional SNMP Adapter optional EPO Emergency Power OFF Remote ON OFF Acoustic signals of various kinds indicating alarm situations Communication with
15. iately reduce the power demand by disconnecting the devices that cause the overload Switch OFF the UPS and repeat point 4 and 5 6 Carry out the LOAD TEST according the modalities described in charter LOAD CONTROL Carry out step 3 4 5 6 of the initial start up procedure to change the configuration of the devices protected by the UPS WARNING It is compulsory to ground the UPS according to safety Standards Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded Risk of electric shock at the output socket if the UPS is ON even when the UPS is not connected to AC utility line Risk of electric shock at the output socket while the unit is connected to AC utility line Disregard for these warnings may lead to a risk of electric shock to operators COMPUTER INTERFACE EVO is gifted with an RS 232 interface which can be used as a communication port with a computer A 9 poles female connector DB9 is fitted on the rear side On the DB9 connector the following RS 232 signals are present e RX pin 2 e TX pin 3 GND pin 5 p
16. in 7 RS 232 interface signals isolated through photo couplers User s manual 13 UPS EVO CAL CHARACTERI STI CS EVO MODEL EVO 1 0 EVO 2 0 EVO 3 0 1000 VA 2000 VA 3000 VA POWER 700 W 1400 W 2100 W NOMINAL INPUT VOLTAGE Single Phase 220 230 V INPUT VOLTAGE RANGE 20 25 96 INPUT OUTPUT FREQUENCY 50 60 Hz automatic selection INPUT FREQUENCY RANGE 5 NOMINAL OUTPUT VOLTAGE Single Phase 220 230 V OUTPUT VOLTAGE REGULATI ON 2 INVERTER WAVEFORM Sinewave THD TOTAL HARMONIC DISTORSION 396 OVERLOAD CAPABILITY 15096 for 30 seconds gt 150 for 10 cycles TYPI CAL TRANSFER TIME 0 ms ON LINE AUTOMATIC AND MANUAL BYPASS Uninterrupted transfer of 10096 load from UPS to Bypass and vice versa CERTIFICATI ONS CE AUTONOMY 8 15 minuts NOMINAL BATTERY VOLTAGE 36 96 96 SEALED MAINTENANCE FREE LEAD ACID 3 units 8 units 8 units BATTERIES 12V 7 2Ah 12V 7 2Ah 12V 7 2Ah TYPICAL BATTERY CHARGE TIME 8 Hours EXPANDABLE AUTONOMY Optional AUDIBLE NOISE at 1 metre 45 dBA COOLING Fan cooling WEIGHT 13 33 34 DIMENSIONS L x H x P 15x21x41 19 x34 x 47 19x34x 47 ENVIRONMENTAL SPECIFICATIONS Temperature 0 40 C Maximum Height 3000 metres Humidity 0 9596 with no condensation COMPUTER INTERFACE 1 RS 232 port UPS MANAGEMENT SOFTWARE Includ
17. ion repeat itself TECNOWARE S r l will provide the final decision on the product substitution Any parts damaged due to the negligence or carelessness in using the product such as failing to follow the correct operating instructions indicated in the user manual violations incorrect installation or maintenance operated by non authorized personnel transportation damages natural calamities accidental causes phenomenon not subordinated to the normal product functioning non qualification of environment in which the product operates and in any case any circumstances in which one cannot date back to the defective manufacture will not be covered by the guarantee Compensation is excluded for direct or in direct damages of any nature caused to people or objects by the incorrect use of product by the discontinuance of product functioning or for stopping the usage due to the product servicing This guarantee is valid upon the terms and conditions cited above in all the countries belonging to the UE countries CONFORMITY TO THE EUROPEAN DIRECTIVES TECNOWARE S r l confirms that EVO models comply with the requirements set out in the Low Voltage Directive Safety 73 23 EEC and following amendments the EMC Electro Magnetic Compatibility Directive 89 336 EEC and following amendments The following standards were applied Low Voltage Directive Safety EN62040 1 1 2003 EMC Directive Electro Magnetic Compatibil
18. ity 1 62040 2 2001 1 61000 3 2 2001 1 61000 3 3 2001 EN55022 1998 1 61000 6 4 20011 PRODUCT DI SPOSAL EVO cannot be disposed as an urban waste but must be treated as a separate waste Any violation is indictable with financial sanctions as per in force regulations An incorrect waste disposal or an improper use of the same or of any parts can be damaging for the environment and for human health A correct waste disposal of products having the dustbin symbol marked by a cross help to avoid negative consequences to the environment and to human health User s manual 21 UPS EVO TECNOWARE power 5 TECNOWARE S r l www service tecnoware com
19. ld continue despite the advised troubleshooting or should they manifest in any other form please contact TECNOWARE SERVICE www service tecnoware com User s manual 17 UPS EVO 5 UTPUT ___ W 4 3 e TER 2 3 dg EA N N C DC CONVERTER BATTERY S N N yy OUIPU N UTPU R ER 2 2Y 2 C DC CONVERTER BATTERY x 3 gt 3 S O m OUTPU N UTPU R ER U X 2 o 3GER BATTERY Figure 1 Operating modes UPS EVO 18 User s manual LINE 3 del 4 BY PASS 5 LOAD INVERTER 6 14 15 16 17 18 19 10 11 12 13 Figure 2 Front panel TEST ON OFF Front buttons LOAD level led bar 1 ON TEST ALARM Button 2 OFF Button 8 OVERLOAD led red 9 LOAD 100 led blue 10 LOAD 80 led blue 11 LOAD 60 led blue 12 LOAD 40 led blue 13 LOAD 20 led blue Operating modes leds BAT level led bar 3 LINE led blue 4 BATTERY led blue 5 BYPASS led blue 6 INVERTER led blue 7 FAULT led red 14 LOW BAT led yellow 15 BAT 20 led blue 16 BAT 40 led blue 17 BAT 60 led blue 18 BAT 80 led blue 19 BAT 100 led blue User s manual 19 UPS EVO ON OFF Remote 4 gt ac x AM ANUAL BYPASS x VL ON of a 7
20. nput mains The UPS will return functioning in LINE mode and will fully recharge the batteries in around 8 hours If the UPS is left unused and disconnected from the mains it is advised to recharge the batteries at least once in a month for around 8 hours After a period of inactivity we advise to carry out the INITIAL START UP procedure described in this manual before using the UPS Carefully follow the rules related to the battery maintenance Otherwise warranty can be declined SAFETY FOR THE OPERATOR If the EVO does not have the original security characteristics it must be made non functional and a non authorised use must be avoided The problem must then be reported to qualified technical personnel The original security characteristics can be lost if for example the EVO shows visible damages or an anomalous running User s manual 15 UPS EVO ANOMALI ES AND TROUBLESHOOTING A list of anomalies and related solutions are described below The UPS does not switch on and does not give any signals Press the ON TEST ALARM button on the front panel for more 1 second If the UPS does not switch on go into the next step Leave the UPS connected to the mains for at least 4 hours in order to recharge the batteries Then try to switch on again The UPS continues to run in BATTERY mode and the mains input voltage is present e Make sure that the UPS input voltage is present and that the voltage amplitude is within th
21. o not remove the cover The UPS contains internal parts which are at a high voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS that can be repaired by the user Any repair or maintenance must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded It is compulsory to ground the UPS according to Safety Standards Risk of electric shock at the output socket when the UPS is ON Risk of electric shock at the output socket while the unit is connected to the AC utility line Use the input power cable given with the unit and connect it to the AC utility line In all circumstances a HO5VVF3G 1 5mm cable or a better one must be used Do not obstruct ventilation slots or holes and do not place any object on top of UPS Do not insert objects or pour liquids in the ventilation holes Do not keep liquids flammable gases or corrosive substances near the UPS Install the UPS indoors in a protected clean and moisture free environment UPS EVO 2 User s manual I NTRODUCTI ON UPS EVO UPS EVO Uninterruptible Power Supplies are the result of constant technological research aimed at obtaining the best performance at the lowest cost UPS EVO are advanced ON LINE UPS single phase built specifically to protect your computer from any irregularities in the AC
22. oltage mode Pin 10 and Pin 1 2 will be open The Dry Contact board is OPTI ONAL UPS EVO 8 User s manual RUNNING OPERATIONS SWITCHING ON If the UPS is switched off and connected to the electric line the LINE Led in the front side is switched on together with the BAT LEVEL led bar showing batteries capacity level In these conditions UPS has the only function of recharging batteries and there is no power on the output sockets switched off output If it is disconnected from the AC utility line after some second UPS is switched off completely The UPS is switched off and connected to the AC utility line LINE Led and BAT LEVEL bar are switched on In order to switch the UPS on it is sufficient to press continuously for more than 1 second ON TEST ALARM button of the front panel till when the UPS emits a short acoustic signal showing its own switching on The UPS effectuates an initial operating SELF TEST during which the red FAULT and OVERLOAD leds are switched on and then activates the power on the output sockets and at the same time it switches on the BYPASS led and the LOAD LEVEL bar indicating output power percentage it starts working in BYPASS mode After some second the BYPASS led is switched off and the INVERTER Led is switched on all this indicates that UPS has started working normally in LINE mode If the UPS is not connected to the AC utility line or if the AC utility line is not present due to a blackout the UPS tu
23. pass AC fail Low BAT 1 2 3 4 5 6 7 8 9 10 The Dry Contact board has a 10 connector on the rear side of the UPS 1 Common Pin 1 and Pin 2 are common pins 2 Fault Pin 3 is the normal open output When UPS works normally Pin 3 and Pin 1 2 will be open when UPS is failed Pin 3 and Pin 1 2 will be closed Pin 4 is normal closed output When UPS works normally Pin 4 and Pin 1 2 will be closed when is failed Pin 4 and Pin 1 2 will be open 3 Bypass Pin 5 is the normal open output When UPS works normally Pin 5 and Pin 1 2 will be open when UPS works in bypass mode Pin 5 and Pin 1 2 will be closed Pin 6 is normal closed output When UPS works normally Pin 6 and Pin 1 2 will be closed when UPS works in bypass mode Pin 6 and Pin 1 2 will be open 4 AC fail Pin 7 is the normal open output When UPS works normally Pin 7 and Pin 1 2 will be open when UPS works in AC failure mode Pin 7 and Pin 1 2 will be closed Pin 8 is normal closed output When UPS works normally Pin 8 and Pin 1 2 will be closed when UPS works in AC failure mode Pin 8 and Pin 1 2 will be open 5 Low Bat Pin 9 is the normal open output When UPS works normally Pin 9 and Pin 1 2 will be open when UPS works in battery low voltage mode Pin 9 and Pin 1 2 will be closed Pin 10 is normal closed output When UPS works normally Pin 10 and Pin 1 2 will be closed when UPS works in battery low v
24. rns on with a sequence similar to the one described above Even in this case it needs to press continuously for more than 1 second ON TEST ALARM button till when the UPS emits a short acoustic signal showing its own switching on The UPS immediately switches on BAT LEVEL bar then it effectuates an initial operating SELF TEST during which the red FAULT and OVERLOAD leds are switched on it switches on BATTERY Led and after some seconds it activates the power on the output sockets and at the same time it switches on INVERTER led and LOAD LEVEL bar indicating output power percentage it starts working normally in BATTERY mode The UPS automatically returns to function in LINE mode a few seconds after the AC utility line is recovered To switch the UPS off press the OFF button for more than 1 second till when the UPS emits a short acoustic signal showing its own switching off The output is disabled and all devices powered by the UPS are switched off The INVERTER led is switched off and UPS effectuates then an operating SELF TEST during which the red FAULT and OVERLOAD leds are switched on If UPS is connected to the AC utility line LINE led and BAT LEVEL led bar remain switched on In these conditions UPS effectuates only batteries recharging function and there is no power on the output sockets switched off output If UPS is not connected with the AD utility line after some seconds it is switched off completely LINE MODE Thi
25. s is the typical running mode the AC input line is present and the amplitude is within specifications The UPS filters the input line performs an output voltage regulation by the RECTIFIER BOOSTER and INVERTER blocks and supplies power to all connected devices Besides it recharges the batteries and keeps them in an ideal charge condition The LINE mode is characterized by e The LINE led and INVERTER led switched on e The LOAD LEVEL and BAT LEVEL led bars switched on User s manual 9 UPS EVO BATTERY MODE The UPS automatically runs in BATTERY mode if the Mains Voltage amplitude gets out of security limits in case of a black out or overvoltage lowvoltage in this case the UPS supplies the required output power by its internal battery and by the DC DC CONVERTER BOOSTER and INVERTER blocks see figure 1 The UPS automatically returns to function in LINE mode a few seconds after the AC input line is recovered The BATTERY mode is characterized by An acoustic signal every 4 seconds indicates that the batteries are discharged The acoustic signal can be disconnected by pressing the ON TEST ALARM button The INVERTER led and BATTERY led switched ON The LOAD LEVEL and BAT LEVEL led bars switched on BYPASS MODE In BYPASS mode see figure 1 the AC input line is directly connected with the UPS outlets by an AUTOMATIC BYPASS EVO uses the BYPASS mode during the start up phase furthermore the UPS switches automati
26. the computer by a RS 232 Interface and possible monitoring of input output voltage frequency output power battery voltage etc Automatic turn on off user programmable by RS 232 Interface Protection filter for the telephone ADSL and data line Possibility to increase the autonomy through External Battery boxes optional High reliability and high performances Easy to use 4 User s manual EXTERNAL DESCRI PTI FRONT PANEL On the front panel there are the control buttons and some leds which indicate the various operating mode and alarm conditions Please see the figures 1 and 2 OFF button To turn off the UPS press this button for more than one second ON TEST ALARM button Can be used for 3 functions e TURN ON the UPS is turned on by keeping the button continuously pressed for more than 1 second e SELF TEST the UPS performs SELF TEST according to the procedure explained further on when the button is pressed during LINE mode for more than 1 second ALARM OFF during BATTERY mode to disable the alarm buzzer press this button for more than 1 second LI NE led This led blue is ON when the input AC line voltage amplitude is within the specification and it indicates the UPS is working in LINE mode If LINE led flashes every second it shows that Phase line and Neutral line of AC input utility line are inverted In that case it must disconnected the AC power input plug from power receptacle turn it at
Download Pdf Manuals
Related Search