Home

Intellinet 524445 router

1. Rule Name Enter a name for the QoS rule up to 15 alphanumerical characters e g VolP Phone Bandwidth Set the bandwidth amount of the QoS rule You need to select the data direction of this rule Upload or Download and the speed of the bandwidth limitation in kbps then select the type of QoS Guarantee guaranteed usable bandwidth for this rule or Max set the maximum bandwidth for the application allowed by this rule ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS Local IP Address Specify the local Source IP address that will be affected by this rule Enter the starting IP address in the left field and enter the end address in the right field to define a range of IP addresses or just enter the IP address in the left field to define a single IP address Local Port Range Enter the range of local Source port numbers that should be affected by this rule To apply this rule on ports 80 to 90 enter 80 90 to apply this rule only to a single port just enter the port number such as 80 Remote IP Address Specify the remote destination IP address that should be affected by this rule Enter the starting IP address in the left field and enter the end address in the right field to define a range of IP addresses or just enter the IP address in the left field to define a single IP address Remote
2. VY INTELLINET NETWORK SOLUTIONS SYSTEM amp NETWORK SETUP 2 5 3 Setup Procedure for PPPoE PPPOE Enter the PPPoE User Name and Password assigned by your Service Provider The Service Name is normally optional but may be required by some Service Providers Enter a Idle Time fin minutes to define a maximum period of time for which the Internet connection is maintained during inactwity Ifthe connection is Inactive for longer than the Maximum Idle Time then the connection will be dropped You can enable the Connect on Demand option ta automatically re establish the connection as soon as you attempt to access the Internet again If your Internet Service Provider requires the use of PPPoE enter the Information below admin 1392 612 lt SMTU lt 1492 Connect Disconnect 1 1000 Minute APPLY CANCEL User Name Enter the user name assigned by your Internet service provider Password Enter the password assigned by your Internet service provider Service Name Enter a name for this Internet service optional MTU Enter the MTU value of your network connection NOTE Use the default value unless your ISP specifies otherwise Connection Type Select one of the three connection types in the drop down menu e Continuous keeps the Internet connection alive and does not disconnect This is the preferred choice for always on flat rate Internet services e Connect on Demand only
3. WIRELESS 150N 300N 4 PORT ROUTER USER MANUAL MODELS 524445 amp 524490 Sd clear S INTELLINET oi INTELLINET NETWORK SOLUTIONS INT 524445 524490 UM 1008 08 0 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless 150N 4 Port Router Model 524445 or Wireless 300N 4 Port Router Model 524490 The latest in wireless networking these Wireless Routers serve multiple purposes an access point for your wireless network a four port router for hard wiring Ethernet devices and bring it all together so that the devices can access a high speed Internet connection Detailed instructions in this user manual make installation reasonably quick and simple so you ll soon be enjoying the benefits of all these popular features e Up to 150 Mbps model 524445 or 300 Mbps model 524490 network link speed e Complies with IEEE 802 11g b standards and is upward compatible with 802 11n e Supports WMM function to meet the multimedia data bandwidth requirement e Supports Wi Fi Protected Setup WPS e Supports WEP and WPA WPA2 TKIP and AES data encryption e Integrated 10 100 Mbps LAN switch with Auto MDI MDI X support e DHCP server assigns IP addresses for all LAN users e DHCP server supports static lease management e Supports virtual server port forwarding and DMZ demilitarized zone e Supports DDNS dynamic DNS e Supports UPnP Universal Plug and Play e Integrated anti DOS firewall e QoS Quality
4. e Flash 2 MB e Memory 16 MB SDRAM e Certifications FCC Class B CE ROHS Router e Supported WAN connection types Dynamic IP DHCP for cable service Static IP PPPoE for DSL PPTP e Protocols CSMA CA CSMA CD TCP IP UDP ICMP PPPoE NTP NAT network address translation DHCP DNS e NAT Virtual server Port forwarding NETWORK SOL UTIONS SPECIFICATIONS Special applications port trigger Firewall Access control based on MAC address URL filter DMZ demilitarized zone Supports UPnP Universal Plug and Play Supports DHCP client server Supports PPPoE DSL DHCP cable and static IP Supports VPN PPTP L2TP and IPsec passthrough Certifications FCC Class B CE Mark RoHS Wireless e Wireless frequency range 2 400 2 483 GHz e Modulation technologies 802 11b Direct Sequence Spread Spectrum DSSS DBPSK DQPSK CCK 802 11g Orthogonal Frequency Division Multiplexing OFDM BPSK QPSK 16QAM 64QAM 802 11n Orthogonal Frequency Division Multiplexing OFDM BPSK QPSK 16QAM 64QAM e Channels USA amp Canada 11 channels Europe 13 channels Japan 14 channels e Data rates IEEE 802 11b 11 Mbps 5 5 Mbps 2 Mbps 1 Mbps IEEE 802 11g 54 Mbps 48 Mbps 36 Mbps 24 Mbps 18 Mbps 12 Mbps 9 Mbps 6 Mbps Model 524445 IEEE 802 11n MCSO 7 up to 150Mbps Model 524490 IEEE 802 11n MCSO 7 up to 150Mbps MCSO 15 up to 300
5. Address Lookup 10 ie INN rA 43 29 Quick SOD seese 13 3 2 1 Port Forwarding cccccee 44 2 3 1 Cable Modem cscee 14 3 2 2 Virtual CONV EM esxtcpteceesccencesseash 45 2 3 2 Fixed IP xDSL Static IP 15 3 2 3 Port Mapping secedecseecertneredeecnees 46 PEC Ss PPPOE XD eA 16 ee ee eee 47 234A PPPTP XDS cerner 16 OAE E C P 47 239 LEZ XDS isise 18 99 FIPCWONNcscccsdcosedatcivsctceteiecsendesostanscs 48 2 3 6 Telstra BigPond sitiuasdetes ta scasecene 18 3 3 1 Access Control cescanrcintdeumeczsen 48 2 4 Basic Setup cccceeeeceeeeeeseeees 19 3 92 Add PO oeei 50 2 4 1 Time Zone Auto Synch 20 3 3 3 URL BIOCKING teccnsenctsccxticeessossecs 51 2 4 2 Changing Mngmt Password 20 3 3 4 DoS Attack Prevention 52 2 4 3 Remote Management 21 ee DN eee E 53 2 5 WAN Setup aonoannnnneneonananannnnnnnn 22 4 ADDITIONAL FUNCTIONS 55 291 VANCE sssusa 23 AN SMAUG 55 292 ONAN WP craseesisr peesi 23 4 1 1 Internet Connections 09 7 3 000 PPEOE 24 41 2 Device Status cece 56 o PPE T r ee ee 24 4 1 3 System LOQ cceeeeeeeeee 56 LS LP a 25 4 1 4 Security Log cece 57 2 9 6 Telstra BigPond 000 26 41 5 Active DHCP Client 57 2 DN ere E 26 4 1 6 Statistics 0 ceeceeeeeeee 57 BO DDN e 27 A2 TOO a ne eon 58 2 6 LAN Configuration ccec 28 4 2 1 Configuration Tools 0 58 2601 LAN IP cisien 28
6. Internet connection setup can be done by using the Quick Setup menu described in section 2 3 However you can set the WAN connections up by using the WAN configuration menu You can also program advanced functions like DDNS Dynamic DNS here Click the WAN menu on the left of the Web management interface then select an Internet connection method based on the type of connection you re using You can either click the connection method in the left side menu or select it from the main panel in the center which requires that you then click More Configuration to continue System WAN b Dynamic IP The Wireless Router can connect to your Internet Service Provider with the following methods F Static IP b PPPoE b PPTP b TF O b Telstra Big Pond b ONS O P ONS O O O WAN Obtains an IP Address automatically tom your Service Dynamic IP en Uses a Static IP Address Your Service Provider gives a Static Static IP IP Address to access Internet services PPP over Ethernet is a common connection method used in PPPoE xDSL connections Point to Point Tunneling Protocol ig a common connection PPTP method used in xDSL connections LAN Wireless QoS 2 NAT Firewall Layer Two Tunneling Protocol is a common connection method L2TP used in xDSL connections Telstra Big Pond Telstra Big Pond is a Internet service is provided in Australia SYSTEM amp NETWORK SETUP VY INTELLINET NETWOR
7. Mbps e Output power OFDM 12 dBm 1 5 dBm 150 Mbps OFDM 12 dBm 1 5 dBm 54 Mbps CCK 16 dBm 1 5 dBm 11 Mbps e Receiver sensitivity 11n 150 Mbps MCS7 20 MHz 64 dBm 40MHz 61 dBm 11g 54 Mbps OFDM 65 dBm 11b 11 Mbps CCK 76 dBm e Maximum coverage distance 100 m 328 ft indoors 300 m 980 ft outdoors SPECIFICATIONS VY INTELLINET NETWORK SOLUTIONS e Wireless security WEP encryption 64 128 bit WPA TKIP WPA2 AES WPA2 mixed WPA RADIUS Client access control through media access control MAC filter e Antennas Model 524445 fixed dipole antenna with 2 dBi gain Model 524490 2 fixed dipole antennas with 2 dBi gain each 2T2R MIMO mode 2 transmitters 2 receivers LEDs e Power e WLAN Link Act e WAN Link Act e LAN 1 4 Link Act Environmental e Dimensions 157 W x 127 L x 30 H mm 6 2 x 5 0 x 1 2 in e Weight 0 8 kg 1 7 Ibs e Operating temperature 0 40 C 32 104 F e Operating humidity 10 90 RH non condensing e Storage temperature 20 60 C 4 149 F Power e External power adapter 5 V DC 1 0 A e Power consumption Model 524445 2 3 Watts max Model 524490 2 7 Watts max NETWORK SOL UTIONS SPECIFICATIONS WASTE ELECTRICAL amp ELECTRONIC EQUIPMENT Disposal of Electric and Electronic Equipment applicable in the European Union and other European countries with separate collection sys
8. Port Range Enter the range of remote destination port numbers that should be affected by this rule To apply this rule on ports 80 to 90 enter 80 90 to apply this rule only to a single port just enter the port number such as 80 If the remote destination IP address and or port number is universal just leave it blank Traffic Type Select the traffic type of this rule from the drop down menu None SMTP HTTP POP3 or FTP To make this rule an IP address based rule to apply the limitation on all traffic from to the specified IP address or port number select None Protocol Select the protocol type of this rulefrom the drop down menu TCP or UDP If you don t know what protocol your application uses try TCP first and switch to UDP if this rule doesn t seem to work Click Save to add the new rule It will appear in the current QoS table Should an error message show up after you click Save you can try again but fixing the problem first and then clicking Save will have a better chance of working To erase all values you ve entered click Reset 3 2 Network Address Translation NAT Network Address Translation NAT also known as Network Masquerading Native Address Translation or IP Masquerading is a technique of transceiving network traffic through a router that involves re writing the source and or destination IP addresses an
9. address or just a keyword of the Web site Enable URL Blocking http speedlimitsaregreat com Add Reset Current URL Blocking Table Pn uRLkeyword Select ralseaurtaxes com C eset APPLY CANCEL Enable URL Blocking Check to enable this function uncheck to disable URL Keyword Enter the URL host name or IP address of a Web site such as http www blocked site com or http 11 22 33 44 or a keyword contained in a URL like pornography sex banner advertisement etc ADVANCED FUNCTIONS NETWORK SOL UTIONS Add Click to add the URL keyword to the URL Keyword Filtering Table Reset Click to remove all entries in the URL Keyword text field Current URL Blocking Table All existing URL keywords in the filtering table Delete Select a URL keyword by checking the Select box of the entry then clicking Delete Delete All Click to delete all existing URL keyword entries 3 3 4 DoS Attack Prevention A denial of service DoS attack is an attempt to make a computer resource unavailable to its intended users DoS attacks generally consist of the concerted malevolent efforts of a person or persons to prevent an Internet site or service from functioning efficiently or at all temporarily or indefinitely One common method of attack involves saturating the target victim machine in this case the router
10. allows an 802 11n wireless network client to connect to this router maximum transfer rate of 300 Mbps e 2 4 GHz B GY only allows a802 11b and 802 11g wireless network clients to connect to this router maximum transfer rate of 11 Mbps for 802 11b clients maximum 54 Mbps for 802 11g clients e 2 4 GHz GY only allows an 802 11g wireless network client to connect to this router maximum transfer rate of 54 Mbps e 2 4 GHz B G N allows 802 11b 802 11g and 802 11n wireless network clients to connect to this router maximum transfer rate of 11 Mbps for 802 11b INTELLINET ETWOR K UTION S SYSTEM amp NETWORK SETUP clients maximum of 54 Mbps for 802 11g clients maximum of 300 Mbps for 802 11n clients NOTE For optimal compatibility with wireless clients select 2 4 GHz B G N ESS D Enter the name for your wireless network You may choose to use the default value but you can adjust the value to make identification in areas with different wireless networks easier e g to differentiate your wireless network from that of your neighbors Channel Number Select a channel from the drop down menu 1 13 for Europe 1 11 for the U S Associated Clients Click Show Active Clients to see the status of all active wireless stations connected to the access point You can try to change the channel number if you think the data transfer rate is too slow There could be interference from other wireless n
11. based on network layer address information such as IP addresses Subnet Mask A subnet mask which may be a part of the TCP IP information provided by your ISP is a set of four numbers e g 255 255 255 0 configured like an IP address It s used to create IP address numbers used only within a particular network as opposed to valid IP address numbers recognized by the Internet which must be assigned by InterNIC TCP IP UDP Transmission Control Protocol Internet Protocol and Unreliable Datagram Protocol are the standard protocols for data transmission over the Internet Both TCP and UDP are transport layer protocols TCP performs proper error detection and error recovery and thus is reliable UDP on the other hand is not reliable They both run on top of the IP Internet Protocol a network layer protocol WAN A Wide Area Network connects computers located in geographically separate areas e g different buildings cities countries The Internet is a wide area network GLOSSARY Y INTELLINET NETWORK SOLUTIONS 7 SPECIFICATIONS Standards e IEEE 802 1d Spanning Tree Protocol e IEEE 802 11b 11 Mbps Wireless LAN e IEEE 802 11g 54 Mbps Wireless LAN IEEE 802 11n 150 Mbps Wireless LAN e IEEE 802 3 10Base T Ethernet e IEEE 802 3u 100Base TX Fast Ethernet General e LAN ports 4 RJ45 10 100 Mbps data ports e LAN ports with Auto MDI MDI X e WAN port 10 100 Mbps RJ45 connector e LAN to WAN throughput 93 Mbps
12. connects to the Internet when there s a connect attempt This is the preferred choice for all users who have paid per minute or per transferred data Internet service e Manual only connects to the Internet when Connect is selected and disconnects when Disconnect is selected Idle Time Out Specify the time to shut down the Internet connection after no Internet activity is detected This option is only available when the connection type is Connect on Demand 2 5 4 Setup Procedure for PPTP PPTP requires two groups of settings the WAN interface settings to set up the IP address and PPTP settings PPTP username and password In the WAN Interface Settings panel select how you obtain an IP address from your service provider Obtain an IP address automatically or Use the following IP address i e a static IP address The WAN interface settings must be correctly SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS entered otherwise the Internet connection will fail even if the PPTP settings are correct Contact your ISP if you don t know how you should fill in these fields e WAN Interface Settings Obtain an IP Address Automatically Host Name eet te tae 000000000000 Clone WAC Use The Following IP Address IP Address SIIRIRIRE Subnet Mask pRIKTAT Default Gateway L 0 0 0 The PPTP Settings panel presents these options e PPTP Settings opr 612 lt MTU lt 1
13. manner Reset q In the event that the system stops responding correctly or stops functioning you can perform a Reboot Your settings will not be changed To perform the reboot click on the APPLY button below You willbe asked to confirm your decision The Reboot will be complete when the LED Power light stops blinking APPLY Apply Click to reset the router It will be operational again after a few minutes NOTE This function does not change any settings you have made It simply restarts reboots the router just as Start Shut Down Restart reboots your computer freeing up memory and system resources for more stable operation 60 ADDITIONAL FUNCTIONS OINTELLINET NETWORK SOLUTIONS 9 TROUBLESHOOTING This section helps you troubleshoot problems you may be experiencing with the router Before you contact your dealer for help you should perform the following troubleshooting steps as they apply to your situation The router is not responding when I want to access it with the Web browser Check the power connection and the connection of the network cable All cords and cables should be correctly and firmly inserted into the router If all LEDs on the router are off check the status of the A C power adapter and make sure it s correctly plugged into your power outlet Verify the IP address you connect to The router s default IP address is 192 168 2 1 but you may have changed it Are you using a MAC o
14. menu DHCP Server Select Enable or Disable from the drop down menu RECOMMENDED VALUES IP Address 192 168 2 1 802 1d Spanning Tree Disabled Subnet Mask 255 255 255 0 DHCP Server Enabled 2 6 2 DHCP Server These settings are only available when DHCP Server in the LAN IP section is enabled but will also affect wireless clients DHCP Server J CANCEL Lease Time Choose a lease time the duration that every computer can keep a specific IP address from the drop down menu of every IP address assigned by this router Start P Enter the start IP address of the IP range End IP Enter the end IP address of the IP range Domain Name Enter a domain name for your network optional NOTE The number of the last field the d field of End IP must be greater than Start IP and can t be the same as the router s IP address Also the first three fields of the IP address of Start IP End IP and IP Address in the LAN IP section the a b and c fields should be the same RECOMMENDED VALUES Lease Time Two Weeks or Forever if End IP 192 168 2 200 you have fewer than 20 computers Domain Name leave it blank Start IP 192 168 2 100 NETWORK SOL UTION S SYSTEM amp NETWORK SETUP 2 6 3 Static DHCP Leases Table This function allows you to assign a static IP address to a specific comput
15. of Service bandwidth management e VPN Passthrough e Use INTELLINET NETWORK SOLUTIONS Wireless N adapters for the best compatibility and performance e Easy installation through Web based user interface e System status e Security log e Firmware upgradeable e Three Year Warranty Package Contents e Wireless 150N 4 Port Router or Wireless 300N 4 Port Router e Quick install guide plus user manual on CD e Power adapter e Ethernet Cats RJ45 cable 1 0 m 3 ft NOTE Some screen images have been modified to fit the format of this manual Images in Hardware sections 1 1 and 1 2 are of the 150N Router Displays and components for the 300N Router are similar NETWORK SOLUTIONS TABLE OF CONTENTS section page section page 1 HARDWARE seivsccinsiscinviccentcastesserneenvennns 5 2 3 Wireless Security 06 33 1 1 Front Panel Display c000 gt 2 1 4 Wireless Access Control 37 1 2 Back Panel Display c00 5 2S NNP ese sabes secactaet nda deena stengeea ys 38 2 SYSTEM amp NETWORK SETUP 6 2 1 6 Security NOS xcsncccaceccssieusseasteres 39 2 1 Connecting the Router 000 6 3 ADVANCED FUNCTIONS 000 41 2 2 Obtaining an IP Address 6 I OOS ee 41 2 2 1 Windows XP Setup 08 T 3 1 1 Basic QoS Settings 41 2 2 2 Windows Vista 7 Setup 9 3 1 2 Adding a new QoS Rule 42 2 2 3 Router IP
16. the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit different from the receiver e Consult the dealer or an experienced radio TV technician for help SECTION NAME VY INTELLINET NETWORK SOLUTIONS VY INTELLINET NETWORK SOLUTIONS INTELLINET NETW OR K SOLUTIONS INTELLINET NETWORK SOLUTIONS offers a complete line of active and passive networking products Ask your local computer dealer for more information or visit www intellinet network com Copyright INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners
17. the packet to its default gateway which will then send it out toward the destination DHCP Dynamic Host Configuration Protocol This protocol automatically gives every computer on your home network an IP address DNS Server IP Address DNS stands for Domain Name System which allows Internet servers to have a domain name such as www Broadbandrouter com and one or more IP addresses such as 192 34 45 8 A DNS server keeps a database of Internet servers and their respective domain names and IP addresses so that when a domain name is requested as in typing Broadbandrouter com into your Internet browser the user is sent to the proper IP address The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you DSL Modem DSL stands for Digital Subscriber Line A DSL modem uses your existing phone lines to transmit data at high speeds Idle Timeout Idle Timeout is designed so that after there is no traffic to the Internet for a pre configured amount of time the connection will be disconnected IP Address and Network Subnet Mask An Internet Protocol address consists of a series of four numbers separated by periods which identifies a single unique Internet computer host in an IP network Example 192 168 2 1 consists of two portions the IP network address and the host identifier The IP address is a 32 bit binary pattern that can be represented as four cascaded de
18. username assigned by Telstra Password Enter the password assigned by Telstra Assign login server manually Select to choose the login server by yourself Server IP Address Enter the IP address of the login server 2 5 Setup Procedure for DNS If you select Dynamic IP or PPPoE as the Internet connection method the ISP typically assigns the DNS server information to the router However if you have a DNS 4 A ONS Domain Name System server is like an index of IP Addresses and Web Addresses If you type a Web address into your browser such as www broadbandrouter com a UNS server will find that name in its index and find the matching IP address Most ISPs provide a ONS server for speed and convenience Since your Service Provider may connect you to the Internet through dynamic IP settings it is likely that the ONS server IP Address is also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP Address of that DNS server The primary ONS will be used for domain name access first In case the primary DNS access failures the secondary ONS will be used ie ober APPLY CANCEL SYSTEM amp NETWORK SETUP Y INTELLINET WOR K SOLUTIONS preferred DNS server or use a Static IP address or if your service provider didn t assign the IP address of the DNS server for any reason you can input the IP address of the DNS server here Primary DNS Enter the IP addres
19. will filter this kind of traffic out Advanced Settings Click to set advanced settings of the DoS prevention method listed above See section 3 3 4 1 DoS Advanced Settings below ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS CANCEL 3 3 4 1 DoS Advanced Settings Clicking Advanced Settings on the first DoS Module screen will display this page acy Module Ping of Death 5 Packet s ner Second E BurstS Discard Ping from WAN NMAP FIN z URG PSH Xmas tree Another Xmas tree Port Scan Mull scan Iv SYN RST Iv SYN 7 FIN lv S N fonly unreachable port Sync Flood 30 Packet s per Second E Burst 30 APPLY CANCEL Ping of Death Set the threshold of when this DoS prevention mechanism will be activated Check the box for Ping of Death and enter the frequency of threshold how many packets per second minute or hour You can also enter the Burst value When this number of Ping of Death packets is received within a very short timeframe this DoS prevention mechanism will be activated Discard Ping From WAN Check the box to activate this mechanism Port Scan A number of port scan methods are listed here Check one or more DoS attack methods you want to prevent Sync Flood As with Ping of Death you can set the threshold for when this DoS prevention mechanism will be activated 3 3 9 Demilitarized Zone DMZ With NAT
20. with external communications requests such that it cannot respond to legitimate traffic or responds so slowly as to be rendered effectively unavailable This router has a built in DoS attack prevention mechanism to prevent DoS attacks from succeeding Activating all options is recommended Ping of Death Ping of Death is a DoS Module special packet and it will cause certain computers to stop responding Check this box and the router will filter out this kind of packet Discard Ping From WAN Ping is a i common and useful tool for knowing the connection status of a specified remote I network device but some malicious intruder could try to fill your network bandwidth with a lot of PING request data packets to make your Internet connection become very slow even unusable Check this box and the router will ignore all inbound PING requests NOTE Unfortunately when you activate this function you will not be able to ping your own router from the Internet either Port Scan An intruder could try to use a port scanner to determine how many ports of your Internet IP address are open through which they can collect a lot of valuable information Check this box and the router will block all traffic that s involved in trying to scan your Internet IP address Sync Flood Another kind of attack this one uses a lot of fake connection requests to consume the memory of your server rendering it unusable Check this box and the router
21. xDSL PPTP xDSL L2TP xDSL and Telstra BigPond Cable Modem and PPPoE xDSL are the most common but if you re not sure which type of service you have simply contact your Internet service provider ISP to find out You won t be able to connect to the Internet if you choose the wrong type during the router setup NOTE DSL Internet Service Providers normally operate using the PPPoE protocol thus PPPoE xDSL should be the broadband type However in recent years more DSL ISPs provide customers with DSL modems that handle the PPPoE portion of Internet access automatically In such cases you need to select Cable Modem as your broadband type even if you have a DSL service 2 3 1 Setup Procedure for Cable Modem Dynamic IP Host Name Input the host name of your computer This is optional and is only required if your service provider asks you to do so SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS 3 IP Address Info q Dynamic IP Cable Modern ooodooddg d Clone MAC BACK OK MAC address Enter the MAC address of your computer here if your service provider only permits a computer with a certain MAC address to access the Internet If you re using a computer used to connect to the Internet via cable modem you can simply click Clone Mac address to fill in the MAC address field with the MAC address of your computer 2 3 2 Setup Procedure for Fixed IP xDSL Static IP 3 IP
22. you identify an address later Add Click to add the MAC address and associated comment to the MAC Address Filtering table Clear Click to remove whatever you entered in the MAC Address or Comment fields 2 5 Wi Fi Protected Setup WPS Wi Fi Protected Setup WPS is the simplest way to build a connection between wireless network clients and this router You don t need to select an encryption mode and input a long encryption passphrase every time you need to set up a wireless client You only need to press a button on a wireless device client and this wireless router and the WPS will do the rest for you WPS Settings This page allows you to change the setting for WPS VVI FI Protected Setup WPS can help your wireless client automatically connect to the Wireless Router Enable WPS Settings Enable WPS Proxy e WPS Information Uncontigured 35904373 INTELLINET Disable Device Configure Registrar i _ otart PBC SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS This router supports two types of WPS Push Button Configuration PBC and PIN code To use PBC you need to push a specific button on the wireless client to start the WPS mode and switch this router to WPS mode You can push the Reset WPS button of this router or click Start PBC in the Web configuration interface to do this To use PIN code you need to know the PI
23. your hands Disconnect the power before you do anything or contact an experienced technician for help If you smell something strange or if you see some smoke coming from the router or power supply remove the power supply or switch the electrical power off immediately and call the dealer for help Li i BZ E ee a AA oo l y D n ON 1 ia waka FA ive gt b Y YY my Al y TO awe FA y i N lt i n fo i b ae am A a oe se ea A S A T F 1 1 Front Panel Display ra POWER WLAN WAN LED Status Description POWER ON Router is switched on and correctly powered WLAN On Wireless network is switched on or WPS mode is on Off Wireless network is switched off Flashing Wireless LAN activity transferring or receiving data WAN On WAN port is connected Off WAN port is not connected Flashing WAN activity transferring or receiving data LAN 1 4 On LAN port is connected Off LAN port is not connected Flashing LAN activity transferring or receiving data 1 2 Back Panel Display L i ON OFF Reset WPS 4 3 2 1 WAN Feature Description Antenna 2dBi dipole antenna 2 antennas on Model 524490 Radio Activate or deactivate the wireless function with this ON OFF switch Reset Reset the router to factory default settings clear all settings or start the WPS WPS function Press and hold for 10 seconds to restore all
24. 13 02 forever 4 1 6 Statistics Statistics of the wireless LAN wired LAN and WAN interface of the router are shown on this screen VY INTELLINET NETWORK SOLUTIONS ADDITIONAL FUNCTIONS Statistics q This page shows the packet counters for transmission and reception regarding to networks Packets Sent 15 Wireless LAN Packets Received PiE Packets Sent 2136 Packets Received 220A Packets Sent 1352 Packets Received 1835 Ethernet LAN Ethernet WAN Fefresh Refresh Click to display the latest information NOTE The information is accumulative and is only reset after the router is restarted 4 2 Tools This screen and the submenus that can be accessed from here provide options and information helpful in managing files and router information Click the Tools link at the upper right corner of the Web management interface 4 2 1 Configuration Tools This screen lets you back up the configuration of the router to a file so you can reload it at a later time You can save different configurations each with unique settings and reload them as needed y INTELLINET Home General Setup Status Tools NETWORK Soe eee a iel E Tools Configuration Tools b Firmware Upgrade EET Use the Backup tool to save the Wireless Router s current configurations to a file named config bin You can then use the Restore tool to restore the saved configuration to the VVireless Router Alternatively
25. 4 2 2 Firmware Upgrade 0 59 2 0 2 DHCP Server sssini 29 A ROSO ce cecactepecess eres assesses 60 2 1 WLAN Configuration 0008 30 5 TROUBLESHOOTING 61 2 1 1 Basic Wireless Settings Ol GLOSSARY ossosa 63 2 1 2 Advanced Wireless Settings 32 7 SPECIFICATIONS sess 65 NETWORK SOL UTIONS TABLE OF CONTENTS SAFETY GUIDELINES For the protection of equipment users and connected devices follow these safety guidelines O A O N gt This router is designed for indoor use only do not place this router outdoors Do not place this router in hot or humid environments Do not yank any connected cables Firmly secure this device if its placed at any significant height Router accessories such as the antenna and power supply should be considered dangerous when handled by children under the age of 3 Keep this device out of the reach of children The router will become hot when used for long time This is normal and is not a malfunction but keep the router away from paper cloth and other flammable materials 7 There are no user serviceable parts inside the router If the router is not working SAFETY GUIDELINES VY INTELLINET NETWORK SOLUTIONS properly contact your dealer place of purchase and ask for help Do not disassemble the router as doing so will void the warranty If the router falls into water while it s powered on do not pick it up with
26. 492 Heese 885 Enable For BEZEQ network in ISRAEL use only Connection Type eI Idle Time Out 1 1000 Minute BACK User Name Enter the username assigned by your ISP Password Enter the password provided by your ISP PPTP Gateway Enter the IP address of PPTP gateway assigned by your ISP Connection ID Enter the connection ID optional MTU Enter the MTU value of your network connection NOTE Use the default value unless your ISP specifies otherwise Connection Type Select one of the three connection types in the drop down menu see PPPoE above Idle Time Out Specify the time to shut down the Internet connection after no Internet activity is detected This option is only available when the connection type is Connect on Demand NOTE Enable BEZEQ ISRAEL only if you re using that network provider 2 5 5 Setup Procedure for L2ZTP L2TP settings are the same as the PPTP connection see section 2 5 4 above SYSTEM amp NETWORK SETUP NETWORK SOLUTIONS 2 5 6 Setup Procedure for Telstra BigPond This procedure is only for the Telstra BigPond network service in Australia 3 IP Address Info 4 Telstra Big Pond lf your Internet serice is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond User Name admin a LI Assign login server manually Server IP Address noon User Name Enter the
27. Address Info q Static IP Enter the IP Address Subnet Mask Gateway IP Address and DNS IP Address provided to you by your ISP in the appropriate fields 172 1 1 1 255 255 0 0 Back o IP address Enter the IP address assigned by your ISP Subnet Mask Enter the subnet mask assigned by your ISP DNS address Enter the IP address of the DNS server provided by your ISP Service Provider Gateway Address Enter the gateway IP address provided by your ISP NOTE You can choose this Internet connection method if your service provider assigns a fixed IP address also know as a static address to you and doesn t use DHCP or PPPoE protocol Contact your service provider for further information NETWORK SOL UTIONS SYSTEM amp NETWORK SETUP 2 3 3 Setup Procedure for PPPoE xDSL 3 IP Address Info q PPPoE Enter the User Name and Password required by your ISP in the appropriate fields If your ISF has provided you with a Service Mame enter it in the Service Mame field otherwise leave it blank 1392 125M U 1492 Continuous Connect ii Disconnect E 10 1 1000 Minute iz User Name Enter the username assigned by your ISP Password Enter the password assigned by your ISP Service Name Provide a name for this Internet service optional MTU
28. Enter the MTU value of your network connection NOTE Use the default value unless your ISP specifies otherwise Connection Type Select one of the three connection types in the drop down menu e Continuous keeps the Internet connection alive and does not disconnect This is the preferred choice for always on flat rate Internet services e Connect on Demand only connects to the Internet when there s a connect attempt This is the preferred choice for all users who have paid per minute or per transferred data Internet service e Manual only connects to the Internet when Connect is selected and disconnects when Disconnect is selected Idle Time Out Specify the time to shut down the Internet connection after no Internet activity is detected This option is only available when the connection type is Connect on Demand 2 3 4 Setup Procedure for PPTP xDSL PPTP xDSL requires two groups of settings the WAN interface settings to set up IP address and PPTP settings PPTP username and password In the WAN Interface Settings panel select how you obtain an IP address from your service provider Obtain an IP address automatically or Use the following IP address i e a static IP address The WAN interface settings must be SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS e WAN Interface Settings Obtain an IP Address Automatically MAC Address NMG tN TEETE Clone MAC Us
29. Firmware Upgrade tool allows you to Upgrade your Wireless Router s firmware The RESET tool allows you to reset your Wireless Router The initial Quick Setup screen presents time settings Time Zone i set the time zone ofthe Wireless Router This information is used for log entries and firewall settings SMTHIO 00 Sreenwich Mean Time Dublin Edinburgh Lisbon London 192 435 244 160 LJ Enable Time From January January Set Time Zone Use the drop down menu to select your time zone Time Server Address Enter the IP address hostname of the time server This isn t normally required but if the default time server NTP should go offline you can obtain a new NTP server from the list at http www ntp org VY INTELLINET NETWORK SOLUTIONS SYSTEM amp NETWORK SETUP Daylight Savings f your locale uses Daylight Saving activate Enable Function and select the duration using the drop down menus Click Next to continue to the next screen of the Quick Setup procedure where you select the broadband Internet connection type you use On all screens click Apply if such button appears at the bottom to submit any option or configuration changes Click Back to return to the previous screen Click Cancel to undo any changes you ve made on that screen Click Next or OK to proceed to the next screen Cable Modem A connection through a cable modem requi
30. K SOLUTIONS 2 5 1 Setup Procedure for Dynamic IP Dynamic IP 4 The Host Name is optional but may be required by some Service Providers The default MAC Address is set to the WWAN physical interface on the Wireless Router If required by your service Provider you can use the Clone MAC Address button to copy the MAC Address of the Network Interface Card installed in your PC and replace the WWAN MAC Address with this MAC Address OOOOOOO00000 Clone MAC Host Name Enter the host name of your computer This is optional and is only required if your service provider asks you to do so MAC Address Enter the MAC address of your computer if your service provider only permits a computer with a certain MAC address to access the Internet If youre using the computer to connect to the Internet via cable modem you can simply click Clone MAC to fill the MAC Address field with the MAC address of your computer 2 5 2 Setup Procedure for Static IP Static IP 4 If your Service Provider has assigned a Fixed IP address enter the assigned IP Address Subnet Mask and the Gateway IP Address provided 172 1 1 1 255 255 0 0 172 1 1 254 APPLY CANCEL IP Address Enter the IP address assigned by your service provider Subnet Mask Enter the subnet mask assigned by your service provider Default Gateway Enter the IP address of the gateway server assigned by your service provider
31. N S My wireless notebook cannot see or connect to the wireless network e Check if Broadcast ESSID is off Remember that you need to input the ESSID on your wireless client manually if the ESSID broadcast is disabled e Check that you ve securely attached the antenna s e Make sure that you re not too far away from the router I can t log on to the Web management interface The password is wrong e Make sure you re connecting to the correct IP address of the router e The password is case sensitive Make sure the Caps Lock feature isn t on e If you ve simply forgotten your password do a hardware reset using the Reset button on the back panel of the router The router becomes hot e It s normal for the router to heat up during operation and this is usually nothing to worry about If however the router gets too hot to touch or if you smell something burning or see smoke coming from the router or A C power adapter immediately disconnect the router and adapter from the utility power making sure it s safe to do this and call your dealer for help The date and time of all the event logs are wrong e Adjust the internal clock of the router TROUBLESHOOTING VY INTELLINET NETWORK SOLUTIONS 6 GLOSSARY Default Gateway Router Every non router IP device needs to configure a default gateway s IP address When the device sends out an IP packet if the destination is not on the same network the device has to send
32. N code of the wireless client and switch it to WPS mode then provide the PIN code of the wireless client you want to connect to this wireless router Click the Wireless menu on the left of the Web management interface then click WPS Enable WPS Settings Check the box to enable the function uncheck to disable Enable WPS Proxy Check the box to enable the function uncheck to disable When enabled it allows another access point to serve as an intermediary device for the connection between wireless network clients and the router WPS Status Configured is displayed if the wireless security encryption function of this wireless router is properly set Not configured is shown if the WPS function has not been configured correctly PinCode Self This is the WPS PIN code of this wireless router which is useful when you need to build a wireless connection by WPS with other WPS enabled wireless devices SS D As it defines this router Authentication Mode If you don t enable the security function of the router before WPS is activated the router will auto set the security to WPA AES and generate a set of passphrase keys for WPS connection Passphrase Key As it was configured Config Mode There are Registrar and Enrollee modes as options for the WPS connection When Registrar is enabled wireless clients will follow the router s wireless settings for a WPS connection Wh
33. SID of this router by setting the Broadcast ESSID option refer to section 2 7 2 Advanced Wireless Settings to Disable Once this option is disabled the router will no longer broadcast the SSID thus wireless clients in the area will not be able to see the wireless network in the list of available WLAN networks Keep in mind that hiding the SSID will make it more difficult for wireless clients to join the network and that is basically the idea Instead of selecting the wireless network from the list the user now must manually enter the wireless SSID which will be difficult without knowing what it is While this option offers additional protection you should never rely on this mechanism as your only means of protection A WPA encryption key is still highly recommended Hiding the SSID of your access point is simply one additional step you can take e Use the Access Control function Section 2 7 4 so people who are not on your list will not be able to connect to your network If you don t have guest traffic you normally know which computers access your network and you can specifically allow those computers and deny all the others e Utilizing all three mechanisms encryption no SSID broadcast and MAC address filtering offers the best protection against unauthorized access SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS 3 ADVANCED FUNCTIONS 3 1 Quality of Service QoS Quality of service provides an effici
34. Scheduler JE File and Printer Sharing for Microsof ai Intemet Protocol Version 6 TCPy IPv6 mee Intemet Protocol Version 4 TCPYIPy4 Install Uninstall Properties Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks SYSTEM amp NETWORK SETUP a NETWORK SOLUTIONS 2 Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator IF address Subnet mask Default gateway Obtain DNS server address automatically Preferred DNS server Alternate ONS server 2 2 3 Router IP Address Lookup 1 After the IP address is set up click Start at the bottom left of the desktop then click Run SYSTEM amp NETWORK SETUP VY INTELLINET NET SOLUTIONS WOR K home user gt Internet aa My Documents Me Internet Explorer mee E mail Outlook Express es Command Prompt w MSN Windows Media Player F Set Program Access and Defaults 4 Windows Messenger Printers and Faxes o Help and Support Files and Settings Transfer po Search Wizard P Log Orr oJ Turn OFF Computer All Programs gt 2 With the Run window displayed
35. TE TO DSL USERS While PPPoE is the most common way to connect to DSL Internet service it still may be necessary to enable Cable Modem in the Broadband settings Below are examples for using Cable Modem instead of xDSL PPPoE even if your Internet service is a DSL service e Your ISP has given you a so called modem router instead of a simple modem e Your ISP has not given you a username and password for PPPoE login implying that it is not required e When your computer is connected directly to the modem the computer obtains an IP address which is in the private IP network range 192 168 xxx yyy 10 xxx yyy 172 16 xxx yyy e You can connect to the Internet with your computer connected directly to the modem without using a dialer program asking for a username and password e If attempts to utilize PPPoE xDSL fail repeatedly you should activate Cable Modem as a troubleshooting step 2 4 Basic Setup This section explains how to change the time zone password and remote Home General Setup Status Tools Quick Setup The Quick Setup provides only the necessary configurations to connect your Wireless Router to your Internet Service Provider SP through an external cable or a DSL modern Liuick Setup General Setup The Wireless Router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings e S
36. al server mapping by checking the Select box of the mapping then clicking Delete If there s no existing mapping this button will be grayed out Delete All Click to delete all existing virtual server mappings Reset Click to unselect all mappings 3 2 3 Port Mapping for Special Applications Some applications require more than one connection a time This function allows these applications to work when they won t work with simple NAT rules Enable Special Applications Check to enable this function uncheck to disable IP Address Enter the IP address of the computer where you want to open the ports Computer Name With all the computers connected to the router listed in this drop down menu you can select a name without checking its IP address TCP Port to Open This is the outgoing outbound range of TCP port numbers for this particular application UDP Port to Open This is the outgoing outbound range of UDP port numbers for this particular application Comment Enter a description for this setting Popular Applications The drop down menu lists some popular applications that require multiple connections To save one to the Current Trigger Port Table select it and click Add Add Click to add a selection to the Current Trigger Port Table Reset Click to remove all entries ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS Special Applications 4 some applications
37. and the firewall this router protects all connected computers in your local network Sometimes however you may want to expose a computer or network device to the Internet intentionally for various reasons e g troubleshooting of network problems Placing a computer in the DMZ puts it at great risk because the protection mechanisms of the router no longer apply So unless you know what you are doing you should not use this function at all Enable DMZ Check to enable this function uncheck to disable Public IP Select Dynamic IP or Static IP If you select Dynamic IP you need to select an Internet connection session from the drop down menu if you select Static IP enter the IP address that you want to map to a specific private IP address Client PC IP Address Enter the private IP address that the Internet IP address will be mapped to That is the computer you want to bypass the firewall and NAT INTELLINET UTION S ADVANCED FUNCTIONS Enable DMZ Ea Current DMZ Table OFFLINE 192 165 2 100 APPLY CANCEL Computer Name With all the computers connected to the router listed in this drop down menu you can select a name without checking its IP address Add Click to add the public IP address and associated private IP address to the DMZ table Reset Click to remove all entries in either panel Current DMZ Table All existing public private IP address mapping
38. assigned using this function Click the Wireless menu on the left of the Web management interface then click Access Control NOTE As explained below all allowed MAC address will display in the MAC Address Filtering table Access Control q For security reason the Wireless Router features MAC Address Filtering that only allows authorized MAC Addresses associating to the Wireless Router MAC Address Filtering Table It allows 20 entries only 00 1b te 01 b3 a1 My Motebook Enable Access Control 0050897 cS066 My Desktop APPLY CANCEL Delete To delete a specific MAC address entry check the Select box of the MAC address you want to delete then click Delete Selected You can select more than one MAC address at a time Delete All Click to delete all MAC addresses listed SYSTEM amp NETWORK SETUP INTELLINET UTION S Enable Access Control Select to enforce MAC address filtering The router will not filter the MAC addresses of wireless clients if this is left unchecked MAC Address Enter the MAC addresses of your wireless devices here without special characters If the MAC address label of your wireless device indicates aa bb cc dd ee ff or aa bb cc dd ee ff just enter aabbccddeeff without the quote marks Comment This is optional and can be left blank but it s recommended that you enter something such as My Desktop as shown that will help
39. ce Select all services you want to allow or deny through this IP address ADVANCED FUNCTIONS NETWORK SOLUTIONS Protocol If the service you need is not listed you can create a new service yourself Select TCP or UDP from the drop down menu and follow the Port Range instructions below If you re not sure which Protocol to use select Both Port Range Enter the port range of the new service To specify ports 80 to 90 enter 80 90 to apply this rule to a single port just enter the port number Add Click to save the settings You ll be re directed to the previous menu and the rule you just set will appear in the IP Filtering Table Reset Click to remove all entries 3 3 3 URL Blocking To prevent computers in the local network from accessing certain Web sites you can define the Web sites IP addresses or keywords here This function is useful for parents and company managers The former can protect children from inappropriate contents on the Internet the latter can protect employees from losing their jobs You can block full Web site URLs such as www microsoft com IP addresses such as 207 46 232 182 or just a part of a URL For example if you enter the keyword downloads the computer can connect to www microsoft com but not www microsoft com downloads URL Blocking 4 You can block access to certain Web sites from a particular PC by entering either a full URL
40. cimal numbers separated by aaa aaa aaa aaa where each aaa can be anything from 000 to 255 or as four cascaded binary numbers separated by bbbbbbbb bbbbbbbb bbbbbbbb bbbbbbbb where each b can either be O or 1 A network mask is also a 32 bit binary pattern and consists of consecutive leading 1 s followed by consecutive trailing O s such as 11111111 11111111 11111111 00000000 Therefore sometimes a network mask can also be described simply as x number of leading 1 s When both are represented side by side in their binary forms all bits in the IP address that correspond to 1 s in the network mask become part of the IP network address and the remaining bits correspond to the host ID For example if the IP address for a device is in its binary form 11011001 10110000 10010000 00000111 and if its network mask is 11111111 11111111 11110000 00000000 it means the device s network address is 11011001 10110000 10010000 00000000 and its host ID is O00000000 00000000 00000000 00000111 This is a convenient and efficient method for routers to route IP packets to their destination NETWORK SOLUTIONS GLOSSARY ISP Internet Service Provider An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations LAN Local Area Network A LAN is a group of computers and devices connected together in a relatively small area Such as a house or an office Your hom
41. configure for UPnP Just select Enable or Disable 3 2 5 ALG Application Layer Gateway ALG is a special function of this router It includes many preset routing rules for numerous applications as shown below that require special support to work with the NAT architecture Check Enable next to the listing and click Apply LINET SOLUTIO ADVANCED FUNCTIONS OINTEL enable Wome Comment OOO Amanda support for Amanda backup tool protocol k Egg support for eggdrop bot networks FIE support for FTP H323 Support for H323 netmeeting IRE Allows DCC to work though NAT and connection tracking lt sl lt sl K MMS support for Microsoft Streaming Media Services protocol Lluakes support for Quake Ill Arena connection tracking and nat Talk Allows netfilter to track talk connections Wee Support for TFTP lt K IPsec support for IPsec passthrough k starcraft support for Starcratt Battle net game protocol MSN support for MSN file tranfer PRIF Pess Through lt K support for PPTP passthrough CANCEL 3 3 Firewall In addition to the NAT feature this router provides firewall functionality to block malicious intruders from accessing the computers on your local network Click the Firewall menu on the left of the Web management interface Wireless Firewall 4 The Wireless Router provides extensive firewall protec
42. ct the settings and make additional changes CONTINUE APPLY click Apply to save the settings and restart the router so the settings will take effect after it reboots Save settings successfully 2 4 2 Changing the Management Password The default password of this router is 1234 and it s displayed on the login prompt when accessed from the Web browser There s a security risk if you don t change the default password since everyone can see it This is very important when you have the wireless function enabled To change the password click the System menu on the left of the Web management interface then click Password Settings Password Settings 4 You can change the password required while lagging into the wireless router s web based management system By default the password is 1254 So please assign a password to the Administrator as soon as possible and store it in a safe place Passwords can contain O to 30 alphanumeric characters and are case sensitive leer APPLY CANCEL Current Password Enter the current password for example 1234 New Password Enter the new password Confirm Password Enter the new password again SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS If the passwords entered in the New Password and Confirmed Password fields aren t the same you ll see the A New passwords do not match messa
43. d usually the TCP UDP port numbers of IP packets as they pass through Checksums both IP and TCP UDP must also be rewritten to take account of the changes Most systems using NAT do so in order to enable multiple hosts on a private network to access the Internet using a single public IP address see gateway Many network administrators find NAT a convenient technique and use it widely Simply put The router s NAT function allows the connection of multiple computers to one Internet line NETWORK SOL UTIONS ADVANCED FUNCTIONS Click the NAT menu on the left of the Web management interface NAT is enabled by default and there is normally no need to change this NAT NAT 4 b Port Forwarding b Virtual Server NAT Network Address ae allows multiple users at your local site to access the Internet through a single Public IP Address gt Special Applications or multiple Public IP Addresses NAT pede Firewall Het tion from hacker attacks and has the flexibility to allow you to map b UPnP Settings Private IP Addresses to Public Ip Addresses for key services such as the Web or FTP ee ee NAT Module Enable O Disable Firewall 3 2 1 Port Forwarding With this function you can tell the router to forward incoming connections bound to a specific port or port range to an IP address on your local network Many online games game consoles with Internet service remote access applications and special network devices s
44. dern data encryption Thus it s not recommended that you use WEP unless you use WLAN adapters or WLAN networking devices that don t support WPA WPA2 encryption If your WLAN card supports WPA WPA2 you can proceed to section 2 7 3 3 Wi Fi Protected Access WPA Security Settings 4 This page allows you setup the wireless security Turn on WEF or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network ex 10 Characters gt CL Enable 802 1x Authentication CANCEL Key Length There are two types of WEP key length 64 bit and 128 bit Selecting 128 bit is safer than 64 bit but will reduce some data transfer performance Key Format There are two types of key format ASCII and hexadecimal or hex When you select a key format the number of characters in the key will be displayed For example if you select 64 bit as the key length and Hex as the key format youll see the message to the right of Key Format is Hex 10 characters which means the length of the WEP key is 10 characters SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS Default Tx Key You can set up to four sets of WEP keys and you can designate one as the default here NOTE If you don t Know which one you should use select Key 1 Encryption Key 1 4 Enter WEP key characters here The number of characters must be the same as t
45. e The Following IP Address IP Address SUTRERERE Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 correctly entered otherwise the Internet connection will fail even if the PPTP settings are correct Contact your ISP if you don t know how you should fill in these fields The PPTP Settings panel presents these options e PPTP Settings on TH i392 612 lt MTU lt 1492 Heese eS Enable For BEZEQ network in ISRAEL use only Connection Type Continuous E Continuous E Connect Disconnect Disconnect Testis 10 1 1000 Minute BACK User Name Enter the username assigned by your ISP Password Enter the password provided by your ISP PPTP Gateway Enter the IP address of PPTP gateway assigned by your ISP Connection ID Enter the connection ID optional MTU Enter the MTU value of your network connection NOTE Use the default value unless your ISP specifies otherwise Connection Type Select one of the three connection types in the drop down menu see PPPoE above Idle Time Out Specify the time to shut down the Internet connection after no Internet activity is detected This option is only available when the connection type is Connect on Demand NOTE Enable BEZEQ ISRAEL only if you re using that network provider SYSTEM amp NETWORK SETUP NETWORK SOLUTIONS 2 3 5 Setup Procedure for L2TP xDSL L2TP is another popular connection method for xDSL and other Inte
46. e network is considered a LAN MAC Address MAC stands for Media Access Control A MAC address is the hardware address of a device connected to a network and is a unique identifier for a device with an Ethernet interface It is composed of two parts three bytes of data that corresponds to the Manufacturer ID unique for each manufacturer and three bytes that are often used as the product s serial number NAT Network Address Translation This process allows all of the computers on your home network to use one IP address Using the broadband router s NAT capability you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP PPPoE Point to Point Protocol over Ethernet Point to Point Protocol is a secure data transmission method originally created for dial up connections PPPoE is for Ethernet connections PPPoE relies on two widely accepted standards Ethernet and the Point to Point Protocol It is a communications protocol for transmitting information over Ethernet between different manufacturers Protocol A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol the interpretation of their behavior is well defined and can be made objectively without confusion or misunderstanding Router A router is an intelligent network device that forwards packets between different networks
47. e username and password If you re certain that the username and password are correct refer to 4 2 Troubleshooting to perform a factory reset to set the password back to the default value TIP This page see 2 3 Quick Setup below shows the four primary setting categories QuickSetup General Setup Status and Tools You can jump to another menu category directly by clicking the link at the top right of each screen NETW OR K SOLUTIONS 2 3 Quick Setup The Quick Setup procedure lets you configure all the settings required for quick Internet access A INTELLINET Home General Setup Status Tools NETWORE SOLUTIONS Quick Setup The Quick Setup provides only the necessary configurations to connect AESA your Wireless Router to your Internet Service Provider ISP through an external cable or a DSL modem General Setup General Setup The Wireless Router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DM We highly recommend you keep the default settings Status status il The Wireless Routers status information provides the following information about your Wireless Router Hardware Firmware version Serial Number and its current operating status Tools Wireless Router Tools Tools include Configuration tools Firmware Upgrade and Reset Configuration tools allow you to Backup Restore or Restore to Factory Default setting for your Wireless Router The
48. ect one or more IP addresses to delete by checking the Select box of those you want to delete then clicking Delete Delete All Click to delete all IP addresses listed NETWORK SOL UTIONS ADVANCED FUNCTIONS 3 3 2 Add PC Clicking Add PC on the Access Control screen will display this page Access Control Add PC This page allows users to define serice limitation of chent PC including IP address and service type ton J F Client Service Service Name Detail Description Select AAAA HTTP TCP Port 80 3128 8000 8060 6051 E mail Sending Mews Forums E mail Receiving secure HTTP File Transfer MSN Messenger Telnet Service Ali MetMleeting DNS SohhiP VPR PPTP VPN L2TP TEF UDE ove TCP Far 28 NNTP TCR Port 119 PORTEE Parni HTTPS TCP Part 445 Pile TE Eim a TCP Port 1663 TEP Port 25 AGL Instant Messenger TCP Port 5190 Haea Der Ren sea sae Nobel aa UDF Port 53 CER Pan IEI T52 TER Rat bees UDF Port 1701 All TCP Part All UDP Part User Define Service E E El El E El El El E El El El El El L a Both E Client PC Description Enter up to 16 alphanumerical characters to describe this IP address Client PC IP Address Enter the starting IP address in the left field and the end IP address in the right field to define a range of IP addresses or just input the IP address in the left field to define a single IP address Client PC Servi
49. ed ADDITIONAL FUNCTIONS OINTELLINET WORK SOLUTIONS Save Click to save the current event log to a text file Clear Click to delete all event log messages displayed Refresh Click to refresh the view to display the most current event log messages 4 1 4 Security Log Security Log 4 View any attempts that have been made to illegally gain access to your network 2010 10 05 Start Dynamic IP 2010 10 05 Pcie eS feel gy etre lel sb qleyanek Sity S a hae Sabre Bees ce Te Va aE a Be i a cli rake E Vedat Weiciss SSshhielsiershst 2010 10 05 3 EANNA Sat maie eo 2 B Aa a e 2010 10 05 3 iret AW Pes aes eel 2010 10 05 a fege S le a e E 2010 10 05 a Arege we A a a I EE 2010 10 05 a Epigews La See ee eE eL a oa 2010 10 05 NTF connect to Tim server 192 43 244 16 2010 10 05 gt FARANE E Jemne SES Save Click to save the current event log to a text file Clear Click to delete all event log messages displayed Refresh Click to refresh the view to display the most current event log messages 4 1 5 Active DHCP Client If youre using the DHCP server function of this router you can use this function to check all active DHCP leases issued by this router Active DHCP Client n This table shows the assigned IP address MAC address and time expired for each DHCP leased client IP Address MAC Address Time Expired Second 192 168 2 100 Cle 1c 23 00
50. en Enrolle mode is enabled the router will follow the wireless settings of wireless client for a WPS connection Configure by Push Button Click Start PBC to start a Push Button style WPS setup procedure This wireless router will wait for WPS requests from wireless clients for two minutes The WLAN LED on the wireless router will be on for two minutes when this wireless router is waiting for an incoming WPS request Configure by Client PinCode Enter the PIN code of the wireless client you want to connect and click Start PIN The WLAN LED on the wireless router will be on when this wireless router is waiting for an incoming WPS request 2 6 Security Tips for Wireless Networks Below are five reminders that will help you maintain a higher level of security for your wireless network e Never use simple words for the WPA WEP encryption passphrase A good NETWORK SOL UTIONS SYSTEM amp NETWORK SETUP password cannot be found in the dictionary and consists of a combination of characters symbols and numbers You should also refrain from using passwords that carry a personal meaning names of pets names or birthdays of a spouse and such as these can easily be guessed by unauthorized users e Use WPA versus WEP whenever possible WPA encryption and even more so WPA2 encryption are much stronger If your wireless network adapters support WPA or WPA2 you should abandon WEP entirely e You can hide the ES
51. ent way for computers on the network to share the Internet bandwidth with a promised quality of Internet service Without QoS all computers and devices on the network compete with each other to get Internet bandwidth and some applications which require guaranteed bandwidth like video streaming and network telephone are affected negatively resulting in an interruption of video audio transfers QoS allows you to limit the maximum bandwidth or grant a guaranteed bandwidth for a specific computer or network service port 3 1 1 Basic QoS Settings Click QoS on the left of the Web management interface QoS 4 Clos Quality of Service refers to the capability of a network to provide better service ta selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flows does not make other flows fail Enable Qos Current QoS Table 1 0 C WolP Phone 2024 Nove Down APPLY CANCEL Enable QoS Check to enable the function uncheck if you prefer not to enforce QoS bandwidth limitations Total Download Bandwidth You can set the limit of total download bandwidth in kilobits To disable the download bandwidth limitation enter 0 Total Upload Bandwidth You can set the limit of total upload ba
52. enter cmd in the Open text field then click OK fq Type the name of a program Folder document or Internet resource and Windows will open it For you Y INTELLINET NET ORK SOLUTIONS SYSTEM amp NETWORK SETUP 3 Enter ipconfig then press lt Enter gt The IP address displays followed by the default gateway In the example below the IP address of the router is 192 168 2 1 cy C WINDOWS system3 cmd exe Co ipconfig Windows IP Configuration Ethernet adapter Local Area Connection Connection specific DNS Suffix IP Address 1 wo w we ew ew ew el tl 1S LIB LS Subnet Mask a ew ew ee a a E 205 255 255 0 Default Gateway w 19221682221 NOTE f the IP address of the gateway is not displayed or if the address begins with 169 recheck the network connection between your computer and the router and re check each step of the network setup procedure 4 Once your computer has obtained an IP address from the router open your Web browser and enter the IP address of the router into the address bar When the login window displays see 2 2 above enter the username admin and the password 1234 Press OK to display the router s Web management interface NOTE lf you can t see the Web management interface and youre being prompted to enter the user name and password again it means you didn t enter the correct username and password Re type th
53. equested senice TCP UDP pot number the Wireless Router redirects the external service request to the appropriate internal server located at one of your LAN s Pirvate IP Address Enable Virtual Server Current Virtual Server Table No Computer Name privare 1P Private Pont Type Public Pon OFFLINE 192 168 2 250 al TEE TANE al Web Server APPLY CANCEL LINET SOLUTIO ADVANCED FUNCTIONS OINTEL Enable Virtual Server Check to enable this function uncheck to disable Private IP Enter the IP address of the computer on the local network that provides Internet service Computer Name With all the computers connected to the router listed in this drop down menu you can select a name without checking its IP address Private Port Enter the port number of the IP address that provides Internet service Type Select the type of connection from the drop down menu TCP UDP or Both If you re not sure which to use select Both Public Port Select the port number of Internet IP address that will be redirected to the port number of the local IP address defined above Comment Enter text to describe this mapping using up to 16 alphanumerical characters e g FTP Server Add Add the mapping to the Virtual Server Table Reset Click to remove all entries Current Virtual Server Table Shows all existing virtual server mappings Delete Select a virtu
54. er forever so you don t need to set the IP address for a computer to enjoy the benefit of using a DHCP server A maximum of 16 static IP addresses can be assigned here NOTE f you set Lease Time to Forever in the DHCP Server section you can also assign an IP address to a specific computer permanently however you won t be able to assign a certain IP address to a specific computer since IP addresses will be assigned in random order this way Enable Static DHCP Leases MAC Address IP Address UO btel 1 baat 192 166 2 190 Add Enable Static DHCP Leases Select to enable de select to disable MAC Address Enter the MAC address of the computer or network device a total of 12 characters with numerals from O to 9 and characters from a to f such as 001122aabbcc IP Address Enter the IP address you want to assign to this computer or network device Click Add to include a MAC address and IP address pair into the Static DHCP Leases table below Click Clear to remove characters entered in a text field Static DHCP Lease Table It allows 16 entries only NO MAC Address IP Address 00 1 b te 01 bs at TE tel 2 210 d To delete a specific item check the Select box of a MAC address and IP address mapping then click Delete Selected To delete all mappings click Delete All To deselect all mappings click Reset 2 Wireless LAN Configuration If your co
55. etworks in the area using the same channel and the cross talk between the two networks can reduce the wireless data transfer rate Ideally you want to set your channel to a value which leaves at least two channels spaced between the two networks Example If your neighbor s wireless network runs on channel 3 set your channel to 6 or higher Even a handheld phone in your household can cause interference with the wireless signal and changing the channel by two or three numbers often resolves the problem 2 2 Advanced Wireless Settings Normally there is no need to make any changes here Unless you know that your network requires special settings you can proceed to 2 7 3 Wireless Security Fragment Threshold Set the fragment threshold of the wireless radio NOTE If you arent sure what this should be set to leave it as the default value of 2346 RTS Threshold Set the RTS return to sender threshold of the wireless radio NOTE f you aren t sure what this should be set to leave it as the default value of 2347 Beacon Interval Set the beacon interval of the wireless radio NOTE If you arent sure what this should be set to leave it as the default value of 100 DTIM Period Set the DTIM delivery traffic indication message period of the wireless radio NOTE If you aren t sure what this should be set to leave it as the default value of 3 Data Rate Set the wireless data transfer rate to a specific value Since mos
56. f the wireless radio Unless you re using this router in a really big space you may not need to set this to 100 WMM Set WMM Wi Fi Multimedia which enhances the data transfer performance of multimedia content sent over a wireless network to Enable or leave it as the default Disable 2 3 Wireless Security Unlike the Advanced Wireless Settings options these settings are critical If not done properly freeloaders can use your Internet connection without your knowledge and hackers could gain access to your network and steal vital data such as credit NETWORK SOL UTIONS SYSTEM amp NETWORK SETUP card information or bank records Click the Security Settings menu on the left of the Web management interface to select one of the four encryption methods from the drop down menu see image below 2 3 1 Disable Wireless Security When you select this mode data encryption is disabled and every wireless device in proximity will be able to connect your wireless router if no other security measure is enabled like using MAC address access control disabling ESSID broadcast NOTE Only use this option when you want to allow everyone to use your wireless router and you don t care if someone reads the data you transfer over the network without your consent 2 3 2 Wired Equivalent Privacy WEP WEP encryption is an outdated method to secure your network as it doesn t meet the security standards of mo
57. ge at right Re enter the new password The page at http 192 168 2 1 says If you see the error message at right it ERROR Password is not matched means the content in the Current Password field is wrong Click OK to go back to the previous menu and try entering the current password again If the current and new passwords are correctly entered click Apply and you ll be prompted to log in again Enter the new password and enter admin for the username 2 4 3 Remote Management This router by default does not allow management access from the Internet to prevent possible security risks especially when you have defined a weak password or didn t change the default password However you can still manage this router from a specific IP address by enabling the Remote Management function Click the System menu on the left of Web management interface then click Remote Management The screen below will display on your Web browser Remote Management 4 The remote management function allows you to designate a host in the Internet to have managementconfiguration access to the Wireless Router from a remote site Enter the designated hast IP Address in the Hast IP Address field Host Address Enter the IP address of the remote host you want to initiate management access Port You can define the port number through which this router should expect an incoming request If you re providing a Web
58. he number displayed n the Key Format field You can use any alphanumerical characters 0 9 a z and A Z if you select ASCII for the key format If you select Hex as key the format you can use 0 9 a f and A F You must enter at least one encryption key here if you enter multiple WEP keys they should not be same Enable 802 1x Authentication IEEE 802 1x is an authentication protocol Every user must use a valid account to log in to this router before accessing the wireless LAN The authentication is processed by a RADIUS server This mode authenticates the user by IEEE 802 1x but it does not encrypt the data during communication If there is a RADIUS server in your environment enable this function Check this box and another sub menu will appear Enable 0 1x Authentication CANCEL RADIUS Server IP address Enter the IP address of the RADIUS server RADIUS Server Port Enter the port number of the RADIUS server RADIUS Server Password Enter the password of the RADIUS server EXAMPLES OF A WEP KEY Obviously you don t want to copy these examples e ASCII 5 characters daisy e ASCII 13 characters digitalFAMILY e Hex 10 characters 28 7d2aa 32 e Hex 26 characters 9284bcda842 c9e036f abcd84 To improve the security level don t use words found in a dictionary or that are too easily remembered daisy is a bad example and is just intended to
59. mputer PDA game console or other network device is equipped with a wireless network interface you can use the wireless function of this router to connect to the Internet and share resources with other computers on your network It s strongly recommended that you use the built in security functions to protect SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS your network from intruders Click the Wireless menu on the left of the Web management interface to open the wireless settings page Remeber to click Apply to save your settings System WAN LAN The Wireless Router can be quickly configured as a wireless access point for roaming clients by setting the Wireless access Identifier and channel number It also supports P Basic Settings data encryption and client filtering b Advanced Settings P Security Settings Wireless 9 P Access Control P WPS Settings p Q05 NAT Firewall 2 7 1 Basic Wireless Settings Basic Settings 4 This page allows you to define ESSID and Channel for the wireless connection These parameters are used for the wireless stations to connect to the Access Paint 2 4 GHz B G N NTELLINET 1 Show Active Clients APPLY CANCEL Band Select one of the options from the drop down menu e 2 4 GHz B only allows an 802 11b wireless network client to connect to this router maximum transfer rate of 11 Mbps e 2 4 GHz NY only
60. ndwidth in kilobits To disable the upload bandwidth limitation enter 0 NOTE Both Total Download and Total Upload bandwidths should be specified according to the maximum ADVANCED FUNCTIONS NETWORK SOL UTIONS performance of your Internet service If you re not sure about these numbers contact your ISP QoS can only be effective if accurate information is provided Current QoS Table All existing QoS rules are shown here Add Click to add new QoS rules see section 3 1 2 Adding a New QoS Rule Edit To modify the content of a specific rule check the Select box of that rule then click Edit NOTE Only one rule should be selected at a time If you didn t select a rule before clicking Edit you ll be prompted to add a new rule Delete You can select one or more rules to delete by checking the Select box of the rule s you want to delete then clicking Delete If the QoS table is empty this button is inaccessible Delete All Click to delete all rules in the QoS table If the QoS table is empty this button is inaccessible Move Up Click to raise the priority of the selected QoS rule Move Down Click to lower the priority of the selected QoS rule 3 1 2 Adding a New QoS Rule After you click Add on the QoS screen you ll have these options Qos This page allows users ta add modify the Glas rule s settings WolP Phone Download E 2024 Kbps EEEE 2 565535
61. omputer connected to a LAN port ON Defaut adminjsz34 the router activate the network connection Start username your Web browser and open http 192 168 2 1 to esse ey display a login window right Remember my password 2 Enter admin as the username and 1234 as the password then click OK Ea SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS NOTE lf this procedure is successful skip the following subsections and proceed to 2 3 Using Quick Setup If the above procedure doesn t result in your obtaining an IP address or if you know that your computer has a static IP address setup follow the steps in the appropriate subsection below 2 2 1 Windows XP IP Address Setup 1 Click Start then go to the control panel Double click the Network amp Internet Connections icon then click Network Connections and double click Local Area Connection to display the Local Area Connection Status window Click Properties Local Area Connection Properties General Authentication Advanced Connect using E9 AMO PONET Family PLI Ethernet 4d This connecton uses the following tems E Clhent for Microsott Networks File and Printer Sharing tor Microsott Networks E Gos Packet Scheduler al Internet Protocol TCP IP ee d Inatall Uninstall Properties Description Transmision Control Protocollnternet Protocol The default wide area network protocol that pr
62. ovides cornmunicatior across diverse interconnected networks _ Show icon in notification area when connected Hotty me when this conmecton has limited or no conmectyity SYSTEM amp NETWORK SETUP NETWORK SOL UTIONS 2 Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK Internet Protocol TCP IP Properties General Alternate Configuration Tou can get F settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Use the following IP address IF address Subnet mask Detault gateway Obtain ONS server address automatically Use the following DNS server addresses Pretered DNS server eal 4lternate ONS server Po Ea SYSTEM amp NETWORK SETUP Y INTEL WOR K SOLUTIONS 2 2 2 Windows Vista 7 IP Address Setup 1 Click Start then go to the control panel Click View Network Status and Tasks then click Manage Network Connections Right click Local Area Network then select Properties With the Local Area Connection Properties window displayed select Internet Protocol Version 4 TCP IPv4 and click Properties amp Intel R PRO 1000 MT Network Connection This connection uses the following items o Client for Microsoft Networks JE QoS Packet
63. r an IP address filter Try to connect to the router with another computer and see if it works if not restore the router s factory default settings by pressing the Reset button on the back panel of the router for at least 10 seconds Set your computer to obtain an IP address automatically DHCP and check if your computer gets an IP address If you did a firmware upgrade before the problem started contact your dealer for assistance I can t get connected to the Internet NETWORK SOL Go to Status Internet Connection and check the Internet connection status Be patient sometimes the Internet is just slow Connect a computer directly to the DSL or cable modem to see if you can access the Internet that way If you can check the WAN connection settings of the router to make sure they are set up correctly Check the PPPoE L2TP PPTP user ID and password again Call your Internet service provider and ask if there s something wrong with their service If you just can t connect to one or more Web sites but you can still use other Internet services check the URL keyword filter to make sure that you are not trying to access a blocked Web site Restart your modem and the router Reset the device provided by your Internet service provider Try to use an IP address instead of a hostname If you can use an IP address to communicate with a remote server but can t use a hostname check the DNS settings TROUBLESHOOTING UTIO
64. re 2003 only support the WEP or WPA TKIP cipher A driver upgrade would be needed for them to be able to use WPA and WPA2 encryption 2 7 3 4 WPA RADIUS If you have a RADIUS server this router can work with it and provide even safer wireless authentication Security Settings 4 This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network OWPATKIP WPAGiIAES OWPA Mixed CANCEL WPA Unicast Cipher Suite Once you select one of the three ciper options SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS WPA TKIP WPA2 AESP or WPA2 Mixed make sure your wireless clients support it RADIUS Server IP address Enter the IP address of the RADIUS server RADIUS Server Port Enter the port number of the RADIUS server RADIUS Server Password Enter the password of the RADIUS server 2 4 Wireless Access Control This function helps to prevent unauthorized users from connecting to your router Only those wireless devices that have the MAC address you assign here can gain access The MAC address is a unique hardware identification number that every network adapter carries You can use this function in combination with data encryption WPA WPA2 or WEP to create an additional layer of security for your wireless network Up to 20 MAC addresses can be
65. re c is an integer between 0 and 254 and d is an integer between 1 and 254 This router is able to work with up to 253 clients so you can set the d field of the router s IP address as 1 or 254 or any number between 1 and 254 and pick a number between 0 and 254 for field c e In most cases you should use 255 255 255 0 as the subnet mask which allows up to 253 clients This also meets the router s capability of working with up to 253 clients e For all servers and network devices that will provide services to other people like Internet service print service and file service use a static IP address Give each of them a unique number between 1 and 253 and maintain a list so everyone can locate those servers easily e For computers not dedicated to providing specific service to others use a dynamic IP address NOTE Recommended setup values are provided in the sections that follow in order to provide further clarification Click the LAN menu on the left of the Web management interface There are three setup groups presented as explained below LAN IP DHCP Server and Static DHCP Leases Table 2 6 1 LAN IP IP address Enter the IP address of this router SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS 192 165 2 1 Paaa haa Ai Disable Enable Subnet Mask Enter the subnet mask for this network 802 1d Spanning Tree Select Enable or Disable from the drop down
66. reads aa bb cc dd ee ff or aa bb cc dd ee ff just enter aabbccddeeff without the quote marks Computer Name With all the computers connected to the router listed in this drop down menu you can select a name without checking its IP address Comment Enter up to 16 alphanumerical characters to identify the MAC address such as Room 2A Computer This is optional and you can leave it blank Add Click to add the MAC address and associated comment to the MAC address filtering table Reset Click to remove all entries in either panel Current MAC Filtering Table All existing MAC addresses in the filtering table Delete You can select one or more MAC addresses to delete by checking the Select box of those you want to delete then clicking Delete Delete All Click to delete all MAC addresses listed Enable IP Filtering Check this box to enable IP address based filtering and select Deny or Allow to determine the behavior of the IP filtering table If you select Deny all IP addresses listed in the filtering table will be denied access to the network if you select Allow only IP addresses listed in the filtering table will be able to connect to the network all other network devices will be rejected Add PC Click to add a new IP address to the IP filtering table Up to 20 addresses can be added Refer to section 3 3 1 1 Add PC below Delete You can sel
67. related information CVE eee Dynamic IP connect ett 10 10 10 00 Subnet Mask 755 255 252 0 Weimer cine 10 10 0 1 ete O01 F21F 08 50 05 SULGE ANL ESS 10 10 85 10 Terme Ees 10 10 85 27 Y INTELLINET NETWORK SOLUTIONS ADDITIONAL FUNCTIONS This screen shows IP address information the router has obtained If you experience problems with your Internet connection open this page and check the contents Values for IP address default gateway and primary DNS should always be filled If they re missing it indicates that there is a connection problem preventing the router from accessing the Internet 4 1 2 Device Status This screen shows information about the wireless configuration as well as the LAN configuration including information about the encryption and IP address settings of the router Wireless Configuration Channel Number INTELLINET 11 LAN Configuration IP Address 192 168 2 1 EME ae 209 299 95 0 te ete ee Enable MAC Address 4 1 3 System Log 00 1F 1F c8 50 00 All important system events are logged here System Log 4 View the system operation information You can see the system start up time connection process and etc here ayslog daemon daemon daemon daemon ayaslogd atarted i BusyBox w1i 11 1 in ati in TS ate bales eae aa Pen ees ee be Say her rajelsst ee S ecole rdiscd 395 Se a celhas SEL Miraeke tS esa tare Peele J packeta receiv
68. require multiple connections such as Internet gaming video conferencing Internet telephony and others These applications cannot work when Network Address Translation WAT is enabled If you need to run applications that require multiple connections specify the port normally associated with an application in the Trigger Port field select the protocol type as TCP or UDP then enter the public ports associated with the trigger port to open them for inbound traffic Note The range of the Trigger Port is 1 to 65535 Enable Special Applications IP Address TCP Port to Open UDP Port to Open 192 168 2 101 20045 1716 1718 8777 2791 Popular Applications e Current ae Port Table OFFLINE 192 166 2100 3724 S066 a 2067 S090 SETT BETI Warcraft APPLY CANCEL Current Trigger Port Table All the settings for the specifal applications are listed here Delete To remove a Special Application setting from the Current Trigger Port Table select the setting and click Delete Delete All Click to delete all existing specifal application settings 3 2 4 UPnP This function enables network auto configuration for peer to peer communications With this function network devices will be able to communicate with other UPnP enabled devices directly and learn about other devices Many network devices and applications rely on UPnP function nowadays UPnP Module Enable Disable APPLY CANCEL UPnP Module There is nothing to
69. res minimal configuration When you set up an account with your Cable provider the Cable provider and your Wireless Router will automatically establish a connection so you probably do not need to enter anything more Fixed IP xDSL some xOSL Internet Service Providers may assign a Fixed IP Address for your Wireless Router If you have been provided with this information choose this option and enter the assigned IP Address Subnet Mask Gateway IP Address and ONS IP Address for your Wireless Router PPPoE xDSL If you connect to the Internet using an xOSL Modem and your ISP has provided you with a Password and a Serice Name then your ISP uses PPPoE to establish a connection You must choose this option and enter the required information PPTP xDSL If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password Local IP Address Remote IP Address and a Connection ID then your ISP uses PPTP to establish a connection You must choose this option and enter the required information L2TP xDSL Layer Two Tunneling Protocol is a common connection method used in xOSL connections Telstra Big Pond lf your Internet service is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond BACK There are six types of Internet connections available as explained below Cable Modem Fixed IP xDSL PPPoE
70. rnet connection types and all required setting items are the same as the PPTP connection see section 2 3 4 above 2 3 6 Setup Procedure for Telstra BigPond This procedure is only for the Telstra BigPond network service in Australia 3 IP Address Info 4 Telstra Big Pond lf your Internet service is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Telstra BigPond LJ Assign login server manually User Name Enter the username assigned by Telstra Password Enter the password assigned by Telstra Assign login server manually Select to choose the login server by yourself Server IP Address Enter the IP address of the login server When all settings are finished and after you click OK youll see Please press APPLY button to restart the system to make the changes take effect this message right on your Web browser Click Apply to restart the router You ll see a second restart message right OK Save settings successfully System Restarting Please wait for a while Wait for about 30 seconds then click OK You ll be forwarded to the router s Web management interface The router is now running with the new settings and if all information entered is correct you can now access the Internet SYSTEM amp NETWORK SETUP VY INTELLINET NETWORK SOLUTIONS NO
71. rt number in the right field To redirect a single port number just enter the port number in the left field Comment Enter text to describe this mapping using up to 16 alphanumerical characters e g camera web port Add Add the mapping to the Current Port Forwarding Table Reset Click to remove all entries Current Port Forwarding Table Shows all existing port forwarding rules port mapping Delete Select a port forwarding mapping by checking the Select box of the mapping then clicking Delete If there s no existing mapping this button will be grayed out Delete All Click to delete all existing port mappings Reset Click to unselect all mappings 3 2 2 Virtual Server This function is very similar to Port Forwarding The difference is that Virtual Server only allows you to specify one port On the other hand it enables you to redirect a public port to a different private port e g public port 80 redirects to private port 85 This makes Virtual Server the obvious choice for hosting public Web services such as a Web server on a computer connected to one of the LAN ports on the router Virtual Server 9 You can configure the Wireless Router as a Virtual Server so that remote users accessing services such as the Web or FIP at your local site via Public IP Addresses can be automatically redirected to local servers configured with Private IP Addresses In other words depending on the r
72. s Delete Select one or more DMZ entries to delete by checking the Select box of those you want to delete then clicking Delete Delete All Click to delete all DMZ entries ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS 4 ADDITIONAL FUNCTIONS FEATURES 4 1 Status This screen and the submenus that can be accessed from here show information about the firmware version of the router the Internet connection IP address information log files and more Click the Status link at the upper right corner of the Web management interface INTELLINET WORK SOLUTIONS Status F Internet Connection status q P Device Status The Wireless Router s status information provides the following information about your Wireless Router Hardware Firrware version Serial Number and its current b security Log operating status amp Actwe DHCP Client P Statistics System P System Log Current Time Boot Code Version BRE 10 5 2010 18 04 21 Runtime Code Version 1 00 In case you experience technical difficulties with the router and need to contact technical support you should write down the Boot Code Version and Runtime Code Version shown on your screen which may vary from the example shown here It is very likely that you would be asked to provide these numbers by the technical support representative 4 1 1 Internet Connection Internet Connection a lew the current internet connection status and
73. s of the DNS server provided by your ISP Secondary DNS Enter the IP address of the secondary DNS server provided by your ISP optional NOTE Only an IP address can be entered here do not use the hostname of the DNS server Only numeric characters and periods are accepted for example 10 20 30 40 would be acceptable but dns serviceprovider com would not be 2 5 8 Setup Procedure for DDNS DDNS Dynamic DNS is an IP to hostname mapping service for Internet users who don t have a static fixed IP address It will be a problem when a user wants to provide services to other users on the Internet because their IP addresses will vary every time they connect and they will not be able to know the IP address they re using at any certain time This router supports the DDNS service of several service providers for example DynDNS http www dyndns org and TZO http www tzo com You can go to one of these DDNS service provider s Web sites and get a free DDNS account by following their instructions DDNS DONS OynamicONSI allows users to map the static domain name to a dynamic IP address You must get a account password and your static domain name from the DONS service providers Our products have DONS support for www dyndns org and waw tzo com now Enable Disable DynDNS mydomain dyndns org mYysermname CANCEL Dynamic DNS Select Enable or Disable Provider Select
74. service default port number is 80 you should try to use another port number You can use the default port setting 8080 or something like 32245 or 1429 any integer between 1 and 65534 Enabled Select the field to start the configuration Click Apply then either click Continue to save the settings and make additional changes or click Apply again to save the settings and restart the router so the settings will take effect after it reboots SYSTEM amp NETWORK SETUP INTELLINET UTION S NOTE To manage this router from another computer on the Internet you need to input the IP address and port number of this router If your Internet service provider assigns you a Static IP address it will not be a problem but if the IP address your service provider assigns will vary every time you establish an Internet connection this will be a problem Either ask your ISP to give you a static IP address or use a dynamic DNS service like DDNS See section 2 5 8 DDNS Client below for details NOTE The default port number the Web browser will use is 80 If the Port setting on this page is not 80 you need to assign the port number in the address bar of the Web browser manually For example if the IP address of this router is 1 2 3 4 and the port number you set is 8888 you need to enter http 1 2 3 4 8888 in the address bar of the Web browser 2 59 Setting Up an Internet Connection WAN Setup The
75. settings to factory defaults press for less than 5 seconds to start WPS 1 4 Local Area Network LAN ports 1 to 4 WAN Wide Area Network WAWN Internet port 5VDC Connects tthe A C power adapter 5V DC NETWORK SOL UTIONS 2 SYSTEM amp NETWORK SETUP 2 1 Connecting the Router 1 Connect your DSL or cable modem to the WAN port of the router using the provided RJ45 Ethernet cable NOTE Standard modems provided by Internet service providers come with at least one LAN Ethernet port which connects to the WAN port of the router SE om an a sn eee ee 2 Connect all your computers and network devices network enabled components like game consoles network media players network storage units or LAN switches to the LAN ports 1 4 of the router 3 Connect the A C power adapter to the wall socket and then connect it to the power jack of the router 4 Check all LEDs on the front panel The PWR LED should be on and the WAN and LAN LEDs should be on if the computer or network device connected to the corresponding router port s is powered on and correctly connected 2 2 Obtaining an IP Address Before you can connect to the router and start configuration procedures your computer must be able to obtain an IP address automatically that is to use a dynamic IP address This is the default setup for any standard Windows computer and it normally is not required to make any changes 1 With your c
76. show how a WEP key looks Wireless clients will remember the WEP key so you only need to input the WEP key for a wireless client once It s worth using a complicated WEP key to improve the security level Once you enter your WEP key and save the settings all wireless clients will need to enter that identical character configuration in order to gain access to your wireless network NOTE 128 bit encryption and ASCII key format are recommended SYSTEM amp NETWORK SETUP NETWORK SOL UTIONS 2 3 3 Wi Fi Protected Access WPA Pre Shared Key security Settings 4 This page allows you setup the wireless security Turn on WEF or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network WPA pre shared key OWPACTKIP WPAZIAES OWPA Mixed Passphrase APPLY CANCEL WPA Unicast Cipher Suite Once you select one of the three ciper options WPA TKIP WPA2 AES or WPA2 Mixed make sure your wireless clients support it Pre shared Key Format Select the type of pre shared key from the drop down menu Passphrase 8 or more alphanumerical characters up to 63 or Hex 64 characters of 0 9 and a f Pre shared Key Enter the WPA passphrase NOTE As mentioned earlier try to avoid common terms or character combinations Some wireless devices especially those manufactured befo
77. t wireless devices will negotiate with each other and pick a proper data transfer rate automatically it s not necessary to change this value unless you know what will happen after modification SYSTEM amp NETWORK SETUP Y INTELLINET NETWORK SOLUTIONS Advanced Settings 4 set the time zone of the Wireless Router This information is used for log entries and firewall settings 256 2346 0 2347 20 1024 ms 1 10 Auto 20 40 MHZ 20 MHZ Short Preamble Long Preamble Enable Disable Outo OAways None 100 O Enable Disable i APPLY N Data Rate Same as above but only for 802 11n clients Channel Width Set the channel width of the wireless radio NOTE If you arent sure what this should be set to leave it as the default setting Auto 20 40 MHz Preamble Type Set the preamble type NOTE If you aren t sure what this should be set to leave it as the default setting Short Preamble Broadcast ESS D Decide if the wireless router will broadcast its own ESSID You can hide the ESSID of your wireless router Select Disable so only people who know the ESSID of your wireless router can connect to it CTS Protect Enabling this function reduces the chance of radio signal collisions between 802 11b and 802 11g n wireless access points NOTE The recommended setting is either Auto or Always Tx Power Set the output power o
78. tatus Status The Wireless Routers status information provides the following information about your Wireless Router Hardware Firnware version Serial Number and its current operating status Tools Tools Wireless Router Tools Tools include Configuration tools Firmware Upgrade and Reset Configuration tools allow you to Backup Restore or Restore to Factory Default setting for your Wireless Router The Firmware Upgrade tool allows you to upgrade your Wireless Router s firmware The RESET tool allows you to reset your Wireless Router VY INTELLINET NETWORK SOLUTIONS SYSTEM amp NETWORK SETUP management settings Start your Web browser and log on to the router s Web management interface by opening http 192 168 2 1 then click the General Setup button on the left 2 4 1 Time Zone and Time Auto Synchronization Click the System menu on the left of the Web management interface then click Time Zone You ll be prompted to select a time zone from the Set time zone drop down menu and enter the IP address or host name of the time server If you want to enable the Daylight Saving setting check the Enable Function box and set the duration of Daylight Saving Click Apply and this message will display Click Continue to save ou may press CONTINUE button to continue configuring other settings or press APPLY button to restart the system to make the changes take effe
79. tems This symbol on the product or its packaging indicates that this product ye shall not be treated as household waste Instead it should be taken to an applicable collection point for the recycling of electrical and electronic EE equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences to the environment and human health which could otherwise be caused by inappropriate waste handling of this product If your equipment contains easily removable batteries or accumulators dispose of these separately according to your local requirements The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product contact your local city office your household waste disposal service or the shop where you purchased this product In countries outside of the EU If you wish to discard this product contact your local authorities and ask for the correct manner of disposal FEDERAL COMMUNICATIONS COMMISSION REGULATORY STATEMENT FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of Federal Communications Commission FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with
80. tion by restricting connection parameters thus limiting the risk of hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ b Access Control b URL Blocking b DoS b DMZ Firewall Module Enable O Disable Firewall Module Check to enable this function uncheck to disable 3 3 1 Access Control This function allows or denies computers with a specific MAC address ora specific IP address protocol or port access to the network Enable MAC Filtering Check this box to enable MAC address based filtering and select Deny or Allow to determine the behavior of the MAC filtering table If you select Deny all MAC addresses listed in the filtering table will be denied access to the network if you select Allow only MAC addresses listed in the ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS Enable MAC Filtering Deny Allow Current MAC Filtering Table Enable IP Filtering Deny Allow Add PC Delete Al APPLY CANCEL filtering table will be able to connect to the network and all other network devices will be rejected Client PC MAC address Enter the MAC address of the computer or network device Dashes or colons are not required For example if the MAC address label of your device
81. u will be prompted to confirm the upgrade The system will automatically reboot the router after you finished the firmware Upgrade process If you dont complete the firmware upgrade process inthe next step you have to reboot the router NEXT nat Next Click to proceed to the upgrade procedure screen Firmware Upgrade 4 This tool allows you to upgrade the Wireless Routers system firmware Enter the path and name of the upgrade file and then click the APPLY button below You will be prompted to confirm the upgrade APPLY CANCEL Browse Click to locate the firmware file you ve downloaded If the file is in Zip compressed archive format you need to uncompress it prior to the upgrade Apply Click to start the firmware upgrade process Never interrupt the upgrade process by closing the Web browser or by physically disconnecting your computer from the router If the upgrade process is interrupted by a network problem or a power failure the router will cease to function Damages resulting from improperly performed firmware upgrades are excluded from the product warranty ADDITIONAL FUNCTIONS VY INTELLINET NETWORK SOLUTIONS 4 2 3 Reset This screen lets you restart the router without disconnecting the power from the unit A restart or system reset may be necessary if the router responds slowly if your Internet connection speed has dropped or if the router behaves in an unusual
82. uch as network cameras require you to open and forward ports often referred to as port mapping With port forwarding the external and internal ports are always the same If you need to redirect an incoming request on public port A to internal port B you need to use the Virtual Server function See section 3 2 2 Virtual Server Port Forwarding 4 Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway s MAT firewall Enable Port Forwarding 1025 Current Port Forwarding Table o comms tane Peme p te poar tan comment so OFFLINE 192 165 2 221 o0 5 Device 1 APPLY CANCEL Enable Port Forwarding Check to enable this function uncheck to disable Private IP Enter the IP address of the computer on the local network that provides Internet service Computer Name With all the computers connected to the router listed in this drop down menu you can select a name without checking its IP address ADVANCED FUNCTIONS VY INTELLINET NETWORK SOLUTIONS Type Select the type of connection from the drop down menu TCP UDP or Both If you re not sure which to use select Both Port Range Enter the starting port number in the left field and enter the ending po
83. you can use the Restore to Factory Default tool to force the Wireless Router to perform System Reset and restore the original factory settings Save Current Time 1 5 2010 18 14 59 l Reset Backup Settings Click Save and you ll be prompted to download the configuration as a file the default filename is default bin Remember to save it as another filename each time you back up for easier retrieval of information ADDITIONAL FUNCTIONS OINTELLINET NETWORK SOLUTIONS Restore Settings Click Browse to select a saved configuration file from your computer then click Upload to transfer the configuration file to the router After the configuration is uploaded the router s current configuration will be replaced by the file you just uploaded Restore to Factory Default Click to reset all settings of the router to the factory default values 4 2 2 Firmware Upgrade The firmware of the router is like the operating system on your computer Firmware upgrades for this router may be available at www intellinet network com If you experience technical difficulties you should first check if any updated firmware is available for the router and install it using this firmware upgrade function Firmware Upgrade 4 This tool allows you to upgrade the Wireless Routers system firmware Enter the path and name of the Upgrade file and then click the APPLY button below Yo
84. your DDNS provider from the drop down menu Domain Name Enter the domain name you ve obtained from the DDNS service provider Account Enter the user account of your DDNS registration Password Key Enter the DDNS service password or key SYSTEM amp NETWORK SETUP NETWORK SOL UTION S 2 6 LAN Configuration This section explains the IP address settings of the local network Normally there is no need to make any changes here The default values work fine for most applications and you could just go directly to section 2 7 WLAN Configuration There are two ways to assign IP addresses to computers static IP address set the IP address for every computer manually and dynamic IP address the IP address of computers will be assigned by the router automatically It s recommended for most of the computers to use a dynamic IP address as it will save a lot of time when setting IP addresses for every computer especially when there are a lot of computers in your network For servers and network devices that will provide services to other computers and users that come from the Internet a static IP address should be used so other computers can locate the server SUGGESTIONS FOR AN IP ADDRESS NUMBERING PLAN If you have no idea how to define an IP address plan for your network here are some suggestions e A valid IP address has four fields a b c d For most home and company users it s suggested to use 192 168 c d whe

Intellinet 524445 router

Contents

Download Pdf Manuals

Related Search

Related Contents