Scosche CJ1282B mounting kit
Contents
1. Read pages 2 3 for kit assembly 1989 95 Dodge Spirit Radio Removal 1 Carefully release the spring type fasteners from the radio console trim panel three from along the top and two from the bottom of the panel 2 Remove two screws from along the top of the side console trim pieces and spread the side piece out slightly for access to the radio bolt 3 After spreading the side piece extract the top right radio mounting bolt then remove the bottom left bolt 4 Spread the side piece once again to provide clearance for pulling the radio out of the cavity pull the radio out disconnect the connectors and remove the radio USE THESE SUPPORT TABS gt C AS REQUIRED REMOVE ALIGNMENT lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt OO lt REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1997 01 Jeep Cherokee Radio Removal 1 Pop out dash bezel bottom first and remove 2 Extract 2 screws holding radio unplug and remove USE THESE SUPPORT TABS gt C HEE AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 32. USE THESE SUPPORT TABS gt 1 pce AS REQUIRED lt _ PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1976 80 Dodge Aspen 1976 80 Plymouth Volare Radio Removal 1 Remove four screws from the bottom of the dash panel Carefully pull the top portion of the panel out and remove the radio 2 Remove two screws securing the radio to the dash and pull the radio out 3 Disconnect power antenna and all speaker electrical connections USE THESE SUPPORT TABS gt 1 en AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt G U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 14 Read pages 2 3 for kit assembly 1975 78 Chrysler Newport New Yorker 1975 77 Dodge Royal Monaco 1975 79 Plymouth Gran Fury Radio Removal 1 Remove three screws from the bottom edge of the dash panel 2 Remove the ashtray and remove one screw retaining the dash panel x 3 Disconnect the cigarette lighter and wiper wires ae 4 Pull the dash panel out from the top Place the gear selector in low gear and remove the dash panel gt 5 Release the radio r
3. 1997 01 Jeep Wrangler Radio Removal 1 Extract 2 screws from dash bezel 2 Pry on bezel to release spring clips and remove 3 Extract 2 screws holding radio unplug and remove USE THESE SUPPORT TABS gt C Een AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1989 95 Plymouth Acclaim Radio Removal 1 Carefully release the spring clips securing the radio dash trim three clips along the top and two at the bottom Disconnect the panel light and remove the trim piece 2 Extract the two bolts securing the radio one at the top right and one at the bottom left of the radio 3 Pull the radio out of the dash cavity disconnect the antenna and all electrical connections and remove the radio USE THESE SUPPORT TABS gt f pects AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT TABS AS U REQUIRED USE THIS Bracket GO USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 23 1996 98 Jeep Grand Cherokee Radio Removal 1 2 3 1993 95 Jeep Grand Cherokee 1992 Radio Removal 1 2 USE THE SHADED MOUNTING TABS AND THE INDICAT
4. connectors and remove the radio USE THESE SUPPORT TABS gt 1 R SPACER AS REQUIRED t REMOVE ALIGNMENT PIN BOTTOM USE THIS BRACKET gt OJO J USE THESE SUPPORT L SPACER PRESS FIT ON ALIGNMENT 2 PLACES TABS AS REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1994 95 Chrysler Town amp Country 1994 95 Dodge Caravan 1994 95 Plymouth Voyager Radio Removal 1 Using a panel removal tool carefully pry up on the dash panel at the base of the windshield speaker grille panel to release the fastening clips securing it to the dash and pull out on the panel to remove 2 Pry up the piece of trim that looks like a vent in front of the instrument light cluster on top of the dash using a panel removal tool to release and remove the trim 3 Carefully pry out on the trim panel surrounding the heater controls using a panel removal tool to release the fastening clips securing the trim to the dash and remove the trim 4 Extract the three screws securing the bottom of the radio trim bezel to the dash 5 Extract the three screws securing the front of the instrument light cluster to the top of the dash 6 Extract the screw securing the back of the instrument light cluster to the dash pry up on the light cluster with a panel removal tool unplug all connectors and remove 7 Extract th
5. ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1995 99 Dodge Neon 1995 99 Plymouth Neon Radio Removal 1 Remove the ashtray from the dash 2 Carefully pry outward on the radio trim bezel to release spring clips then remove 3 Extract the two 3 8 screws securing the radio to the dash pull the radio from the dash cavity unplug all connectors disconnect the ground strap and remove the radio USE THESE SUPPORT TABS gt C ene AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt joy J REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 17 Read pages 2 3 for kit assembly 1987 96 Dodge Dakota Radio Removal 1 Remove eight screws from the dash trim panel 2 Remove two screws from the underside of __ the steering column trim and remove the eo trim a 3 Remove two screws from the radio a mounting bracket disconnect power antenna speaker leads and all other electrical connections and remove the radio USE THESE SUPPORT TABS gt f oR AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT TABS AS U REQUIRED USE THIS Bracket gt OCL USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAG
6. REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 stor Read pages 2 3 for kit assembly 1974 80 Dodge Pickup Ramcharger 1974 80 Plymouth Trailduster Radio Removal 1 Remove four screws from the top edge of the dash panel 2 Remove seven screws on the front surface and three under the dash panel 3 Carefully pull the panel from the dash and remove it 4 Remove two screws securing the radio to the dash Pull the radio out 5 Disconnect the power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt C Ea AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O J U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 18 Read pages 2 3 for kit assembly 1979 83 Chrysler Imperial 1979 81 Chrysler Newport 1979 83 Chrysler New Yorker 1979 81 Dodge St Regis Radio Removal 1 Remove four screws securing the radio dash panel two above the radio and two above the heater controls 2 Remove radio dash panel 3 Remove two screws securing the radio to the dash Pull the radio out 4 Disconnect power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt 7 aE AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt fey J REQUIRED USE T
7. TABS gt C CANT AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt joy U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1997 00 Dodge Dakota Radio Removal 1 Remove eight screws from the dash trim panel 2 Remove two screws from the underside of the l steering column trim and remove the trim 7 3 Remove two screws from the radio mounting e bracket disconnect power antenna speaker i leads and all other electrical connections and remove the radio USE THESE SUPPORT TABS gt C NT AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt eon J REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 15 Read pages 2 3 for kit assembly 1979 82 Dodge 024 1978 90 Plymouth Horizon 1983 87 Dodge Charger 1983 90 Plymouth Scamp 1978 90 Dodge Omni 1979 82 Plymouth TC3 1982 84 Dodge Rampage 1983 87 Plymouth Turismo Radio Removal 1 Remove seven screws from the top and bottom edges of the radio dash panel and remove the panel 2 Remove two screws securing the radio to the dash and pull the radio out 3 Disconnect power antenna and all speaker and electrical connections
8. anti theft bolts retaining the radio use Snap On bit TTW 12 for 1 4 drive and remove the radio Disconnect power ground cable antenna and speaker wires USE THESE SUPPORT TABS gt C gee AS REQUIRED lt lt PIN BOTTOM USE THESE SUPPORT TABS AS U REQUIRED USE THIS BRACKET gt OIO USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 5 Read pages 2 3 for kit assembly 1990 93 Chrysler Fifth Avenue Imperial 1988 93 Chrysler New Yorker 1988 93 Dodge Dynasty Radio Removal 1 Remove five screws from along the top side of the radio instrument panel dash trim 2 Lower the steering column place the gear selector in drive then remove the trim panel 3 Remove two bolts securing the radio and pull the radio out disconnect wire harnesses ground strap and antenna lead then remove the radio USE THESE SUPPORT TABS gt J AS REQUIRED REMOVE ALIGNMENT lt PIN BOTTOM USE THESE SUPPORT TABS AS U REQUIRED USE THIS BRACKET gt OIO USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1979 89 Chrysler Fifth Avenue 1977 81 Chrysler Le Baron 1977 89 Dodge Diplomat 1980 89 Plymouth Gran Fury Radio Removal 1 Remove four s
9. wiring A test light or grounded wire probe can cause damage to the vehicle s computer and or diagnostic systems Avoid all factory airbag wiring Airbags can accidentally deploy causing serious injury or death NOTES e See your vehicle s instructions for any special l l CJ1282 tools your installation might require e Read all instructions accompanying your car stereo cassette player for proper wiring and p mounting instructions re SAE ASSEMBLING THE KIT The instructions for each vehicle show which mounting panel and brackets to use Use the shaded mounting tabs and indicated brackets Carefully break or cut off the unused brackets Then assemble the radio and the mounting panel as shown below and secure the kit to your dash using the supplied screws Reassemble your dash and attach the radio s front panel and controls The following example shows a typical installation IN DASH DIN PULLOUT DETACHABLE FACEPLATE DIN E RADIOS The kit panel comes DIN ready Follow the instructions supplied with the radio secure the mounting kit Install the assembly in the dash and use the rear support strap supplied with the radio to support the rear of the radio CJ1279 CJ1282 MOUNTING RADIO S PANEL SUPPLIED oe TRIM PLATE RADIO S MOUNTING CAUTION SLEEVE REAR SUPPORTING THE RADIO ADDS TO THE INSTALLATION S STRUCTURAL INTEGRITY DIN RADIO Read pages 2 3 for kit assembly
10. 21 Read pages 2 3 for kit assembly 1978 01 Dodge Ram Van 1978 83 Plymouth Van Radio Removal 1 Remove two screws securing the dash panel inside the glove box 2 Remove four screws from the bottom edge of the dash panel and one on the left side of the panel 3 Carefully pull the panel from the dash and remove the panel 4 Remove two screws securing the radio to the dash Pull the Sy radio out a 5 Disconnect power antenna and all speaker and electrical ae l connections USE THESE SUPPORT TABS gt C AS REQUIRED REMOVE ALIGNMENT lt PIN BOTTOM USE THESE SUPPORT TABS AS U REQUIRED USE THIS BRACKET gt OO USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1987 94 Dodge Shadow 1987 94 Plymouth Sundance Radio Removal 1 Remove the ashtray 2 Carefully pull outward on the edges of the trim panel to release the snaps and remove the panel 3 Remove one retaining screw from above the right upper corner of the radio 4 Pull the dash trim towards the passenger side to gain access to the upper right radio bolt remove the top right bolt and the lower left bolt 5 Pull out the radio Disconnect the power antenna speaker leads and all other electrical connections Remove the radio USE THESE SUPPORT TABS gt C ca
11. AS LJ lt REQUIRED OC 4 USE THISBRACKET 22 ASSEMBLING THE KIT Cont d REAR DIN ISO MOUNT DIN E Radio with Side Mounting Holes SUPPORT 1 Snap the DIN iso side mounting brackets to the back of the mounting panel SIRAP 1 left and 1 right Use supplied hardware to bolt them to the back of the kit panel 2 Snap the DIN ISO Trim Ring into the radio opening 3 Load the Radio from the REAR of the mounting panel until the nose piece of the radio comes through the front of the kit y 4 Use the 5MM screws to secure the radio from the sides DIN RADIO CAUTION REAR SUPPORTING 5MM SCREWS THE RADIO ADDS TO THE INSTALLATION S G STRUCTURAL CJ1279 INTEGRITY ISO MOUNTING BRACKETS T CJ1279 CJ1282 MOUNTING PANEL CJ1279 TRIM RING FACTORY WIRE CODES For Factory Wiring Codes go to www scosche cars com Read pages 2 3 for kit assembly 1995 00 Chrysler Cirrus 1996 00 Chrysler Sebring JX Convertible 1995 00 Dodge Stratus 1996 00 Plymouth Breeze Radio Removal 1 Carefully pry out on the radio heater control trim bezel unsnap to remove 2 Extract two 3 8 bolts holding radio in unplug and remove radio NOTE The rear of the aftermarket stereo should be supported USE THESE lt REMOVE SUPPORT TABS gt ALIGNMENT AS REQUIRED PIN TOP USE THIS o BRACKET J lt _ USE THESE SUPPORT TABS AS REQUIRED USE THE SHADED MOUNTIN
12. D MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1990 Chrysler Town amp Country 1984 90 Dodge Caravan 1984 90 Plymouth Voyager Radio Removal 1 Pull firmly outward on the console radio trim panel secured by five metal spring clips two at the top two on the right side and one on the left side 2 Extract the top two screws from each side of the lower console this allows you to slightly spread the console providing clearance to remove the radio 3 Remove the remaining two screws securing the radio disconnect the connectors and remove the radio USE THESE SUPPORT TABS gt C fone AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt fey J REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 13
13. E 3 Read pages 2 3 for kit assembly 1990 93 Dodge Daytona Radio Removal 1 Reach behind ashtray and unsnap the carrier housing to remove the ashtray 2 Remove three screws along the top edge of the radio trim panel 3 Remove two screws below the radio trim panel Remove the trim panel 4 Remove two screws securing the radio to dash then pull the radio out 5 Disconnect the power antenna and all speaker and electrical connections Remove the radio USE THESE SUPPORT TABS gt J AAA AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt GO U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 16 Read pages 2 3 for kit assembly 1989 95 Chrysler Le Baron GTC Convertible Sro a Radio Removal 1 2 Gently pry outward on the radio trim bezel to release seven snap clips and remove Extract two hex head bolts holding radio in place and slide radio outward Unplug all power speaker connectors unplug antenna and unbolt ground strap remove radio USE THESE SUPPORT TABS gt G REMOVE AS REQUIRED ALIGNMENT lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt fey U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATIO
14. ED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly Extract 5 screws from along top of dash instrument bezel Carefully pop out wood grain trim panel around a c heater control Carefully pop out wood grain trim panel around headlight switch Extract 4 screws from along bottom of dash instrument bezel lift up and away to remove Extract 2 3 8 hex heard bolts holding radio unplug connectors and remove USE THESE SUPPORT TABS gt C AS AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt fey U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly Jeep Grand Wagoneer Extract two screws from above the radio securing the radio trim bezel Extract two screws from above the diagnostics display panel securing the radio trim bezel Carefully remove the ashtray and extract two screws located in the ashtray cavity securing the radio trim bezel Pull the radio trim bezel away from the dash unplug all connectors and remove the bezel Extract two nuts securing the radio to the dash and pull the radio from the cavity unplug all connectors and remove the radio lt USE THIS USE THESE BRACKET SUPPORT TABS gt _ AS REQUIRED USE THESE SUPPORT TABS
15. G TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 3 Read pages 2 3 for kit assembly 1993 97 Chrysler Concorde 1993 97 Dodge Intrepid 1993 97 Eagle Vision Radio Removal 1 Pull the radio trim bezel out to release the snap clips and remove the bezel 2 Extract the two bolts securing the radio pull the radio from the cavity unplug all connectors and remove the radio USE THESE SUPPORT TABS gt J ehh AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt tom U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1980 83 Chrysler Cordoba 1980 83 Dodge Mirada Radio Removal 1 Remove four screws securing the radio dash panel two above the radio and two above the heater controls 2 Remove the radio dash panel Remove two screws securing the radio to the dash Pull the radio out 3 Disconnect power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt C Ae AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 4
16. HE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1984 86 Chrysler Laser 1984 89 Dodge Daytona Radio Removal 1 Remove one screw from each side of the ashtray Pull off the trim panel 3 Remove two screws securing the radio to the dash Pull the radio out 4 Disconnect the power antenna and all speaker and electrical connections N USE THESE SUPPORT TABS gt J PA AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O J U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 7 Read pages 2 3 for kit assembly 1982 83 Chrysler Le Baron 1981 84 Dodge Aries 1982 83 Dodge 400 1981 83 Plymouth Reliant Radio Removal 1 Remove four screws from the top of the radio panel trim and four from the bottom of the panel trim Remove the panel 2 Remove two bolts retaining the radio and remove the radio Disconnect the power ground cable antenna and speaker wires USE THESE SUPPORT TABS gt C ATER AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATIO
17. N SEE PAGE 3 1985 89 Chrysler Le Baron GTS 1985 89 Dodge Lancer Radio Removal 1 2 dash trim panel and remove the trim panel TTW12 for 1 4 drive which secure the radio to the dash substructure pull the radio out of the cavity disconnect all wiring and remove the radio Read pages 2 3 for kit assembly Remove eleven screws from the perimeter of the Remove two anti theft bolts use Snap On bit USE THESE SUPPORT TABS gt C AAR AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 9 Read pages 2 3 for kit assembly 1989 94 Chrysler Le Baron Landau Radio Removal 1 Starting from the bottom gently pry outward on the radio trim bezel to release the two spring clips on the bottom and three across the top 2 Unplug the lamp harness from the back of the trim bezel and remove 3 Extract two screws above radio one at the lower right corner behind glove box door and one screw at the lower right hand corner below steering column 4 Remove the trim panel around the radio itself 5 Extract two hex head screws holding radio in place unplug all connectors and unbolt ground strap 6 Remove radio USE THESE SUPPORT TABS gt C AOA AS REQUIRED lt PIN BOTTOM USE THESE SU
18. N SEE PAGE 3 Read pages 2 3 for kit assembly 1987 93 Chrysler Le Baron Coupe Radio Removal 1 Remove two screws one from each lower corner of the radio console trim panel 2 Gently snap off the trim panel 3 Remove two screws securing the right side panel of the console one at top one at bottom remove the side panel 4 Remove two screws from the radio mounting bracket Disconnect the wire harness antenna lead and ground strap Remove the radio USE THESE SUPPORT TABS gt 7 Ae AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O j U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 8 1998 00 Dodge Durango Read pages 2 3 for kit assembly Radio Removal 1 Extract 3 screws from the bottom edge of small center plastic panel below steering column pry out on panel to remove 2 Use a panel removal tool to carefully pry out on the radio dash panel unsnap unplug the left side of the panel and remove 3 Extract 2 10MM bolts holding radio in unplug and remove radio USE THESE SUPPORT TABS gt J pete AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt ey U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN
19. PPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1994 97 Chrysler LHS 1994 96 Chrysler New Yorker Radio Removal 1 Remove the ashtray from the dash 2 Carefully pry out on the perimeter radio dash bezel using a panel removal tool to release the fastening clips and remove the radio dash bezel 3 Extract the two screws securing the radio to the dash pull the radio from the dash cavity unplug all connectors and remove the radio USE THESE SUPPORT TABS gt 1 iE AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt OC 3 U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 10 Read pages 2 3 for kit assembly 1974 78 Dodge Charger Monaco 1978 79 Dodge Magnum Radio Removal 1 Remove four screws from the bottom edge of the radio dash panel 2 Remove two screws from the top edge of the panel above the radio location 3 Unscrew the retainer ring securing the remote mirror control and remove the panel 4 Remove two screws securing the radio to the dash Pull the radio out 5 Disconnect power antenna and all speaker and electrical connections USE THESE SUPPORT
20. SCOSCHE CJ1279 CJ1282 IN DASH INSTALLATION KIT FOR SELECT 1974 UP CHRYSLER AND JEEP VEHICLES TABLE OF CONTENTS CHRYSLER DODGE Cont d DODGE Cont d 1995 00 CIRRUS n se 3 1985 89 ARIES n 5 1979 81 ST REGIS ooeeececccseseeseeeseeees 7 1993 97 CONCORDE ssns 4 1981 84 ARIES en 8 1995 00 STRATUS oo eecececeseceseseseeeees 3 1980 83 CORDOBA ssssisssucctvesencssays 4 1976 80 ASPEN nnn 14 1975 79 CORDOBA nesses 5 1995 00 AVENGER cececcccccccccccceceeeee 11 EAGLE 1983 84 EGLASS eect ee eee 5 1996 00 CARAVAN a 12 1993 97 VISION 4 1990 93 FIFTH AVENUE siiccssacsnstsns 6 1994 95 CARAVAN o e B i 1979 89 FIFTH AVENUE n se 6 1991 93 CARAVAN o oo 13 1990 93 IMPERIAL ooien 6 1984 90 CARAVAN T 13 JEEP 1979 83 IMPERIAL oone 7 1983 87 CHARGER 14 1997 01 CHEROKEE na 21 1984 86 LASER sne 7 1974 78 CHARGER 15 1996 98 GRAND CHEROKEE 22 1984 88 LE BARON onsen 5 997 00 DAKOTA seciseseiescessiseconccsens 15 1993 95 GRAND CHEROKEE 22 1982 83 LE BARON oneee 8 1987 96 DAKOTA e 16 1992 GRAND WAGONEER 22 1977 81 LE BARON cccccceseeeeees 6 1990 93 DAYTONA k ja 16 1997 01 WRANGLER oaeee 23 1987 93 LE BARON COUPE 8 1984 89 DAYTONA oo 7 1989 95 LE BARON GTC n se 9 1977 89 DIPLOMAT e 6 PLYMOUTH 1985 89 LE BARON GTS 8 9 1998 00 DURANGO ooe 17 1989 95 ACCLAIM o s 23 1989 94 LE BARON LANDAU 10 1988 93 DYNASTY oaaae 6 1996 00 BREEZE ien 3 1994 97 LHS seses
21. YAGER ne 13 1963 68 600 ES e 5 1984 90 VOYAGER osaic 13 Your vehicle s information is just a mouse click away PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO SCOSCHE FACTORY WIRING Autosound HARNESS Encyclopedia cro1 on line at 1984 up Chrysler vehicles LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly wire harness codes and information pertaining to installation of kits CJ1279 CJ1282 in 1974 UP in Select Chrysler and Jeep Vehicles Scosche Industries Inc can not be held responsible for discrepancies inconsistencies that may occur due to the automobile manufacturing changes or options or damage that may occur in the automobile during the installation of components while using this booklet If you have any further questions call TECH HELP 1 800 621 3695 ext 3 2005 SCOSCHE INDUSTRIES INC SI 4 05 CJ1279 CJ1282 3000360 INTRODUCTION The Scosche In Dash Installation Kit for 1974 UP Chrysler and Jeep Vehicles provides the parts you need to mount your car stereo cassette player into your vehicle s dash Refer to the individual instructions in this manual to remove your vehicle s factory installed radio PRELIMINARY PARTS LIST CAUTION Disconnect your vehicle s negative battery terminal before the installation to help CJ1279 prevent electrical damage We recommend the use of a volt ohm meter over a test light to check
22. crews from the top edge of the dash panel and four screws from the bottom edge Remove the panel 2 Remove two screws securing the radio to the dash and pull out 3 Disconnect power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt J Ra AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O J U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 6 Read pages 2 3 for kit assembly 1998 01 Dodge Ram Pickup Radio Removal 1 Extract 1 Screw from lighter socket area 2 Carefully pryout on the radio dash bezel to release the fastening clips disconnect all connectors and remove the bezel 3 Extract the 2 screws securing the radio to the dash pull the radio from the dash cavity unplug all connectors diconnect the ground strap and remove the radio USE THESE SUPPORT TABS gt J faeries AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT TABS AS UU REQUIRED USE THIS BRACKET gt ClO J USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1994 97 Dodge Ram Pickup Radio Removal 1 Remove the ashtray from the dash extract the two screws securing the ashtray bracket t
23. e three screws securing the top of the radio trim bezel to the dash on the drivers side of the dash 8 Pull the radio trim bezel away from the dash unplug all connectors shift the gear select lever into Low tilt the steering wheel down and remove the bezel 9 Extract the two screws securing the radio to the dash pull the radio from the cavity disconnect the ground strap unplug all connectors and remove USE THESE REMOVE SUPPORT TABS gt ALIGNMENT the radio AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 12 Read pages 2 3 for kit assembly 1991 93 Chrysler Town amp Country 1991 93 Dodge Caravan 1991 93 Plymouth Voyager Radio Removal 1 Remove the cigarette lighter 2 Using a panel removal tool carefully pry outward to release the clips securing the dash bezel and remove the bezel 3 Extract the two screws securing the rear hatch switch to the dash bezel 4 Extract the two 3 8 bolts securing the radio to the dash 5 Pull the radio out of the dash and unplug all the connectors Disconnect the ground strap and remove the radio USE THESE REMOVE SUPPORT TABS gt C Hy MEME AS REQUIRED SIN BOTTON USE THESE SUPPORT USE THIS TABS AS BRACKET gt O J U REQUIRED USE THE SHADE
24. ear support Remove two screws securing the radio to the dash Pull the radio out 6 Disconnect the power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt C AA AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1995 00 Chrysler Sebring 1995 00 Dodge Avenger Radio Removal 1 Carefully pry out on radio AC control trim bezel to release the snap clips Remove the bezel 2 Extract the two screws holding radio in unplug connector unbolt ground wire from rear of radio and remove radio lt USE THIS BRACKET USE THESE TOP USE THESE I SUPPORT TABS AS BOTTOM REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 11 Read pages 2 3 for kit assembly 1996 00 Chrysler Town amp Country 1996 00 Dodge Caravan 1996 00 Plymouth Voyager Radio Removal 1 Extract two screws in the trim bezel from just above the radio 2 Pull the radio trim bezel away from the dash unplug the ac heating control 3 Extract the two screws securing the radio to the dash pull the radio from the cavity disconnect the ground strap unplug all
25. o the dash and remove the bracket 2 Open up the cup holder and extract the two screws securing it to the dash 3 Carefully pry out on the perimeter radio dash bezel using a panel removal tool to release the fastening clips disconnect all connectors and remove the bezel 4 Extract the two screws securing the radio to the dash pull the radio from the dash cavity unplug all connectors disconnect the ground strap and remove the radio USE THESE SUPPORT TABS gt J R AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt eF U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 19 Read pages 2 3 for kit assembly 1981 93 Dodge Pickup Ramcharger 1981 Plymouth Trailduster Radio Removal 1 Remove five screws from the edge of the dash panel 2 Remove one screw from the dash panel above the radio 3 Carefully pull out the bottom of the panel to release the panel clips and remove the panel 4 Remove two screws securing the radio to dash and pull out the radio 5 Disconnect the power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt C yvonne AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE
26. ren AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt OJ U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 20 Read pages 2 3 for kit assembly 1975 79 Chrysler Cordoba 1975 77 Plymouth Fury Radio Removal 1 Remove four securing screws from the bottom edge of the radio dash panel 2 Remove two securing screws from the top edge of the panel above the radio 3 Unscrew the retainer ring securing the remote mirror control and remove the panel 4 Remove two screws securing radio to the dash Pull the radio out 5 Disconnect power antenna and all speaker and electrical connections USE THESE SUPPORT TABS gt q PEAR AS REQUIRED lt PIN BOTTOM USE THESE SUPPORT USE THIS TABS AS BRACKET gt O U REQUIRED USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS CUT OFF THE REMAINING TABS AND DISCARD FOR DIN ISO RADIO INSTALLATION SEE PAGE 3 Read pages 2 3 for kit assembly 1983 84 Chrysler E Class 1983 88 Dodge 600 ES 1984 88 Chrysler Le Baron 1985 89 Dodge Aries 1984 87 Chrysler New Yorker 1985 89 Plymouth Reliant Radio Removal 1 Remove nine securing screws from the top and bottom of the radio trim panel Remove the panel by pulling it down and out 2 Unhook the wiring harness 3 Remove the two Chrysler
27. tycssestatsencemensscveneten 10 1993 97 INTREPID sien 4 1975 77 FURY oenen 5 1979 81 NEWPORT nsss 7 1985 89 LANCER senn 9 1980 89 GRAN FURY a 6 1975 78 NEWPORT nasses 11 1978 79 MAGNUM nsien 15 1975 79 GRAN FURY oaaae 11 1994 96 NEW YORKER nsns 10 1980 83 MIRADA oosa 4 1978 90 HORIZON siec 14 1988 93 NEW YORKER ss 6 1974 78 MONACO onoo 15 1995 99 NEON cser 17 1984 87 NEW YORKER s ssssseenes 5 1995 99 NEON seeren 1z 1985 89 RELIANT oaie 5 1979 83 NEW YORKER ss 7 1978 90 OMNI aiser 14 1981 83 RELIANT oaii 8 1975 78 NEW YORKER s s s 11 1981 93 PICKUP FULLSIZE 18 1983 90 SCAMP oen 14 1995 00 SEBRING seein 11 1974 80 PICKUP FULLSIZE 18 1987 94 SUNDANCE oi 20 1996 00 SEBRING JX CONV 3 1998 01 RAM PICKUP oaeiae 19 1979 82 TO3 einna 14 1996 00 TOWN amp COUNTRY 12 1994 97 RAM PICKUP ooe 19 1981 TRAILDUSTER oiiaii 18 1994 95 TOWN amp COUNTRY 12 1978 01 RAMVAN cccccseceseseeeeeees 20 1974 80 TRAILDUSTER oiiaii 18 1991 93 TOWN amp COUNTRY 13 1981 93 RAMCHARGER 18 1983 87 TURISMO o 14 1990 TOWN amp COUNTRY 13 1974 80 RAMCHARGER 18 1978283 VAN eenen 20 1982 84 RAMPAGE s 14 1976 80 VOLARE nee 14 DODGE 1975 77 ROYAL MONACO 11 1996 00 VOYAGER oiii 12 1979 82 O24 aaun 14 1987 94 SHADOW oona 20 1994 95 VOYAGER i 12 4982 83 4 00 raana 8 1989 95 SPIRIT nena 21 1991 938 VO
Download Pdf Manuals
Related Search