Metra 95-7861 mounting kit
Contents
1. Yellow Right Front Gray Black GTOUNT 5 0 2 Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 95 7861 INSTRUCTIONS 4 800 221 0932 m www metraonline com REV 05 29 08 COPYRIGHT 2004 2008 METRA ELECTRONICS CORPORATION INST95 78612. INSTALLATION INSTRUCTIONS FOR PART 95 7861 APPLICATIONS Honda Pilot 2003 2005 2006 2008 Without Factory Navigation 95 7861 KIT FEATURES e Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS ADC Double DIN Trim Plate B EX Double DIN Trim Plate C Double DIN Brackets LX Double DIN Trim Plate B EX Double DIN Trim Plate C Double DIN Brackets S TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool o Phillips Screwdriver Socket Set eS Sy YG N L 1 800 221 0932 www metraonline com COPYRIGHT 2004 2008 METRA ELECTRONICS CORPORATION q So ES TABLE OF CONTENTS Dash Disassembly Honda Pilot 2003 2005 1 Honda Pilot 2006 2008 Without Factory Navigation 2 Kit Assembly DIN Radio Provision 3 SO Radio Provision 4 Final Assembly es ssseos as onesenrenensmsnmauesure 5 Note Refer also to the instructions included with the aftermarket radio zh i I Mais 95 7861 DASH DISASSEMBLY HONDA PILOT 2003 2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Using a small flat blade screw driver remove the blank plate from upper right side of radio trim panel Figure A 3 Unsnap radi
3. ded with the aftermarket radio NOTE Select the proper radio housing for your vehicle EX models use the EX Double DIN Trim Plate and LX models use the LX Double DIN Trim Plate Snap the Double DIN brackets to the inside edge of the Double DIN trim plate Figure A 2 Slide the stacked ISO units into the bracket trim plate assembly and secure the units to the assembly using the screws sup plied with the units Figure B Continue to final assembly rT MESA 955 7861 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory
4. o trim panel Unplug switches and remove panel Figure B 4 Remove 4 10mm bolts securing radio unplug and remove radio R Figure C Continue to kit assembly rT Que 95 7861 DASH DISASSEMBLY HONDA PILOT 2006 2008 Without Factory Navigation 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Remove 2 screws from the top of the instrument panel trim Unclip and remove the instrument panel trim Figure A 3 Unclip and remove the left center trim panel Figure B 4 Unclip the radio trim panel Unplug and remove the panel Figure C 5 Remove the 4 screws securing the radio Unplug and remove the radio Figure D Continue to kit assembly zz f Mena sA 95 7861 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio NOTE Select the proper radio housing for your vehicle EX models use the EX Double DIN Trim Plate and LX models use the LX Double DIN Trim Plate 1 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate Figure A 2 Slide the Double DIN radio into the bracket trim plate assembly and secure the radio to the assembly using the screws supplied with the radio Figure B Continue to final assembly rt LES 95 7861 KIT ASSEMBLY STACKED ISO UNITS PROVISION Note Refer also to the instructions inclu
Download Pdf Manuals
Related Search