Infocus SP-WALLKIT-02 project mount
Contents
1. WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 25 lbs 11 34 kg for the SP WALLKIT 02 34 11 MIN 59 58 MAX TRAVEL 29 5 54 5 7 25 3 OF LEVEL ADJ USTMENT 5 63 57 8 2 28 Peg A BOLTCIRCLE 1 61 fed L A YAW ADJUSIMENTPOINT 10 128 7 5 07 2 5 6 L THREADS ONTO 1 1 2 NPT ROLL ADJ USTMENT POINT 4 INTERFACE LOCKING SWITCH PIC H ADJ USTMENT POINT as 2 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 LEGEND Pencil Mark Marcar con lapiz Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com l pis Serrare il fissaggio Segno a ma2. 17 3 Lift projector so that screws with thumb nuts are aligned with mounting slots in mount base 4 Slide projector with mounting bracket onto mounting slots in mount base until screws are seated against the back of mounting slots See Figures 17 and 18 Figure 18 WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make certain mounting slots in mount base slide under thumb screws and that screws are seated in the back of slots 5 Verify mounting screws are properly seated in mounting slots in mount base See Figure 19 6 Move locking lever to locked position See Figure 19 7 Insert key into lock and turn to secure projector to mount See Figure 17 reverse view Figure 19 Projector Mount Adjustments Yaw Adjustment 1 Loosen yaw adjustment locking screw using a 2 Phillips screwdriver See Figure 20 2 Turn Yaw micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 20 3 Tighten Yaw adjustment locking screw using a 2 Phillips screwdriver See Figure 20 Figure 20 10 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Pitch Adjustment NOTE Pitch can be adjusted using the projector mount or the pitch of the entire arm can be adjusted See Pitch Adjustme
3. Figure 49 10 Repeat Steps 8 9 for remaining three bolts one bolt at a 7 Optional Remove projector from short throw projector time mount according to projector interface instructions NOTE It will be necessary to remove projector prior to install four security screws to projector bracket For ease of installation it is recommended to remove projector prior to performing the following steps WARNING It is important to replace adapter plate bolts ONE AT A TIME or adapter plate could fall from mount during installation 8 Remove one of four bolts from adapter plate See Figure 50 adapter plate U x 4 one at a time Figure 51 11 Reinstall projector to mount Refer to Projector Installation Section for details 18 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Visit the InFocus support site at www infocus com support 19 SP WALLKIT 02 Installation Instructions InFocus Corporation InFocus 13190 SW 68th Parkway Ste 200 Portland OR 97223 8802 002043 Rev00 2010 InFocus Corporation www infocus com 09 10
4. IMPORTANT See Site Requirements section before proceeding with Steel Studs installation to ensure installation site meets requirements The drywall must have a minimum thickness of 1 2 1 Determine mounting location on wall Use stud finder to locate steel studs For studs less than 16 apart mounting brackets will have to be adjusted See Adjustments section for details 2 Draw a dotted line down the center of the studs to be used for mounting 3 Line up four holes on mounting bracket with center of studs at desired mounting location See Figure 5 4 Using mounting bracket as a template mark four holes at the inner four holes in bracket See Figure 5 5 Drill four 1 2 holes at marked locations in wall See Figure 5 front view steel studs CT B eo SCH Lief d eo Figure 5 6 Hold metal channel on anchor P flat alongside plastic straps and slide channel through hole See Figure 6 Drywall Plastic saps L on 1 Figure 6 7 Holding plastic straps on anchor P pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud See Figure 7 8 Slide plastic cap on anchor P towards wall until flange of cap is flush with wall See Figure 7 Visit the InFocus support
5. in wall See Figure 1 o 7 oP front view Figure 1 4 Install four concrete anchors K into drilled holes See Figure 2 5 Install four 5 16 x 2 1 2 hex head lag screws L through four 5 16 washers M outer holes of mounting bracket B and into concrete anchors K See Figure 2 Wood Studs 1 Determine mounting location on wall Use a stud finder to locate studs For studs less than 16 apart mounting brackets will have to be adjusted See Adjustments section for details 2 Draw a dotted line down the center of the studs to be used for mounting 3 Line up inner four holes on mounting bracket B with center of studs at desired mounting location See Figure 3 4 Using mounting bracket B as a template mark four holes at the holes in bracket See Figure 3 5 Drill four 7 32 holes at marked locations in wall See Figure 3 wood studs Figure 3 6 Install four 5 16 x 2 1 2 hex head lag screws L through four 5 16 washers M holes of mounting bracket and into drilled holes See Figure 4 6 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Steel Studs
6. INSTALLATION INSTRUCTIONS Dual Stud Short Throw Wall Mounts InFocus SP WALLKIT 02 SP WALLKIT 02 Installation Instructions DISCLAIMER InFocus and its affiliated corporations and subsidiaries collectively InFocus intend to make this manual accurate and complete However InFocus makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind InFocus makes no representation of warranty expressed or implied regarding the information contained herein InFocus assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty Itis the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided
7. acket 4 channel or from above and down behind and into wall mount e Routing Cables from Below Steps 4 and 5 Open cable clips along bottom edge of wall bracket cross bracket See Figure 25 Visit the InFocus support site at www infocus com support 11 SP WALLKIT 02 Installation Instructions e Routing Cables from Above Step 6 6 Thread cables down through a surface mount cable accessory not included then behind and into the wall bracket See Figure 27 Proceed to Step 7 7 Route cables through cover mount projector arm tunnel and into projector See Figure 28 cables view from front Surface Mount Cable Accessory not included Figure 25 5 Thread cable up wall bracket channel and into opened cable clips See Figure 26 Proceed to Step 7 Figure 26 bottom view cable example projector Figure 28 12 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 8 Optional Cables can be tied to inside of projector s front cover using cable ties not included Route cables near front cover and wrap cable tie through slots on front cover and around cables See Figure 29 cable tie not included va RES route through slots and Of around cables Figure 29 9 Replace removed cable management co
8. e stud 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center There must be a minimum of 1 7 8 48mm clearance inside wall Drywall 1 2 minimum Drywall Thickness Both Sides of Stud See hazard statement on page 2 Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 125 18 C Shape S Stud Section Visit the InFocus support site at www infocus com support 5 SP WALLKIT 02 Installation Instructions Assembly and Installation The SP WALLKIT 02 short throw projector mounts can be mounted to concrete concrete block wood studs or steel studs They can be mounted to studs up to 16 apart For studs more than 16 apart the SP WALLADPT 24 accessory not evaluated and tested by Underwriters Laboratories can be used to mount projector Mounting Wall Bracket Concrete or Concrete Block 1 Determine mounting location on wall 2 Using mounting bracket B as a template mark four holes at the holes in bracket See Figure 1 3 Drill four 3 8 holes at marked locations
9. ion Instructions TOOLS REQUIRED FOR INSTALLATION AN g e 3 16 5 32 included included security 2 1 2 12 7mm 3 8 9 5mm 1 2 12 7mm 7 82 5 6mm 7 16 11 2mm PARTS a ZZ A 1 Short throw wall mount SS C 2 wall bracket D top cap wall bracket bottom cap F 10 H 4 14 20 x 5 8 a J 4 S n 8 32 x 1 2 1 4 20 x 3 8 1 4 20 x 1 1 2 L 4 K 4 410 24 x1 3 g concrete anchor 5 16 x 2 1 2 Q wall bracket v wy Qe v e z 4 ae S 4 e gt Q 4 3 16 RM T 2 5 16 1 4 20 x 1 3 4 1 4 20 1 4 10 24 x 3 8 1 4 20 x 1 2 security s5 gt SV amp Y Z 3 AA 3 U 4 V 10 E X 1 S ag M4x12mm M4 1 4 20 x 3 4 8 32 x 1 2 security security security interface bracket projector mount 4 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the sam
10. justments Bracket Width Adjustment 1 Loosen two flat head cap screws on wall bracket See Figure 35 2 Slide wall brackets to corresponding width of studs See Figure 35 3 Tighten two flat head cap screws on wall bracket See Figure 35 o E QDD E O Figure 35 Pitch Adjustment Entire Arm 1 Remove two 8 32 x 1 2 Phillips pan machine screws F to free outer cover from mounting bracket See Figure 36 Figure 36 2 Slide outer cover of mount A away from mounting bracket to expose pitch adjustment screw See Figure 37 14 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Figure 39 Figure 37 8 Slide outer cover of mount A back against mounting bracket See Figure 39 3 Loosen two 1 4 20 x 5 8 hex head cap screws E on underside of mounting bracket See Figure 38 9 Reinstall two 8 32 x 1 2 Phillips pan machine screws F through holes on sides of outer cover See Figure 40 Figure 38 4 Loosen two bolts on either side of pitch adjustment screw See Figure 39 5 Adjust pitch adjustment screw until mount is at desired pitch Figure 40 level Turn clockwise to raise mounting level or turn counte
11. nt Entire Arm Section for details Loosen Pitch adjustment locking screw using a 2 Phillips screwdriver See Figure 21 Turn Pitch micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 21 Tighten Pitch adjustment locking screw using a 2 Phillips screwdriver See Figure 21 D e Cy Figure 21 Roll Adjustment 1 Loosen ROLL adjustment locking screw using a 2 Phillips screwdriver See Figure 22 Turn ROLL micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 22 Tighten ROLL adjustment locking screw using a 2 Phillips screwdriver See Figure 22 underside IOO Figure 22 Cable Management Optional 1 2 Remove two screws 8 32 x 1 2 Phillips pan machine screws F to release mount cover See Figure 23 Slide mount cover away from wall mount See Figure 23 Figure 23 NOTE In most cases cable management covers will NOT 3 need to be removed in order to route cables from projector to the wall mount But for some thick cables removing the covers may be necessary Remove cable management covers if necessary from short throw projector arm See Figure 24 bottom view projector Figure 24 NOTE Cables may be routed from below and up wall br
12. op plate onto cross bracket on mounting bracket See Figure 10 Figure 11 Install two 1 4 20 x 5 8 hex head bolts E through holes on short throw projector arm A and into sliding nuts on mounting bracket B DO NOT TIGHTEN SCREWS AT THIS POINT See Figure 12 bottom view X o 9 e H 3 gt 2 S A N g Figure 10 2 Slide lower plate onto cross bracket on mounting bracket See Figure 11 Figure 12 Loosen two bolts on either side of pitch adjustment screw See Figure 13 Adjust pitch adjustment screw until mount is at desired pitch level Turn clockwise to raise mounting level or turn counterclockwise to lower mounting level See Figure 13 Tighten two bolts on either side of pitch adjustment screw See Figure 13 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 02 Figure 13 Tighten two bolts installed in Step 3 See Figure 12 8 Slide outer cover of mount A back against mounting bracket See Figure 13 9 Install two 8 32 x 1 2 Phillips pan machine screws F through holes on sides of outer cover See Figure 14 Figure 14 Projector Installation WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is
13. pport site at www infocus com support Installation Instructions SP WALLKIT 02 Security Screw Installation Optional 1 Remove eight 8 32 x 1 2 Phillips pan machine screws F from wall bracket covers See Figure 45 projector arm not shown for display purposes Figure 45 Figure 47 2 Install eight 8 32 x 1 2 button head security screws V 5 Remove two bolts holding stop bracket in place on into holes in wall bracket covers See Figure 46 underside of short throw projector mount See Figure 48 projector arm not shown for display purposes Figure 46 3 Remove two 8 32 x 1 2 Phillips pan machine screws F holding mount cover on projector arm See Figure 47 4 Install two 28 32 x 1 2 button head security screws V into holes on mount cover See Figure 47 Figure 48 Visit the InFocus support site at www infocus com support 17 SP WALLKIT 02 Installation Instructions 6 Install two 1 4 20 x 1 2 button head security screws T through holes in stop bracket and into holes in sliding nuts See Figure 49 adapter plate stop bracket x 4 one at a time d e Figure 50 9 Install one 1 4 20 x 3 4 button head security screw U into hole vacated by removing bolt in Step 8 and into plastic spacer See Figure 51 T x2
14. rclockwise to lower mounting level See Figure 39 6 Tighten two bolts on either side of pitch adjustment screw See Figure 39 7 Tighten two 1 4 20 x 5 8 screws E on underside of mounting bracket See Figure 39 Visit the InFocus support site at www infocus com support 15 SP WALLKIT 02 Installation Instructions Extension Adjustment 1 Loosen two bolts holding stop bracket in place on underside of short throw projector mount See Figure 41 Adjust mount to desired extension length See Figure 37 Tighten two bolts holding stop bracket to secure mount in desired position See Figure 41 bottom view Figure 41 Lateral Shift Adjustment 1 Remove two 8 32 x 1 2 Phillips pan machine screws F to free outer cover from mounting bracket See Figure 42 Figure 42 2 Slide outer cover of mount A away from mounting bracket See Figure 43 Figure 43 3 Loosen two 1 4 20 x 5 8 hex head cap screws E on underside of mounting bracket See Figure 44 4 Adjust projector arm laterally to desired position See Figure 44 5 Tighten two 1 4 20 x 5 8 hex head cap screws loosened in Step 3 See Figure 44 6 Slide outer cover of mount A back against mounting bracket See Figure 43 7 Replace two 8 32 x 1 2 Phillips pan machine screws removed in Step 1 See Figure 42 Figure 44 16 Visit the InFocus su
15. site at www infocus com support Steel Stud Drywall Plastic Cap gt gt d Anchor Metal Channel SIDE VIEW Figure 7 9 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 8 10 Repeat steps 7 through 9 for each mounting hole Steel Stud Dial lt O Plastic Cap y Plastic Straps Anchor Metal Channel SIDE VIEW Figure 8 11 Place wall bracket over anchors and align mounting holes in display mount with holes in anchors See Figure 9 12 Insert 1 4 20 x 1 3 4 Phillips pan head screws N through 1 4 washer Q corresponding mounting hole on wall bracket and into anchor P and tighten until flush against mount DO NOT overtighten See Figure 9 13 Repeat steps 11 through 12 for remaining 3 mounting holes WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware SP WALLKIT 02 Installation Instructions Steel Stud Drywall Q x4 N x 4 BR B Anchor Metal Channel SIDE VIEW Figure 9 Installation to Wall Bracket 1 Lt short throw projector arm A up to mounting bracket B and hook t
16. the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 25 lbs 11 34 kg for the SP WALLKIT 02 bottom view Figure 15 Projector Mount Installation 1 Line up mounting holes on projector mount Y with corresponding holes on mounting plate See Figure 15 2 Install four 10 24 x 1 3 8 Phillips pan machine screws J through projector mount holes and into mounting plate See Figure 16 IMPORTANT If projector mount is NOT installed in the same direction as shown in Figure 16 ROLL adjustment screws will be inaccessible I mounting plate p LP adjustment screws eo x4 Figure 16 Visit the InFocus support site at www infocus com support 9 SP WALLKIT 02 Installation Instructions Projector Installation to Mount WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only the hardware provided by the manufacturer 1 Secure interface bracket X to top of InFocus projector using three M4x12mm Phillips pan machine screws Z and three M4 washers AA See Figure 17 InFocus projector Figure 17 2 Orient projector with interface bracket as shown in Figure
17. tita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Destornillador Phillips Ajustar Einstellen Ajustar Regolare Kruiskopschroevendraaier Afstellen Tournevis a pointe cruciforme Ajuster Llave de boca Quitar Gabelschl ssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Cl fourche Retirez A mano Opcional Von Hand Optional Com a m o Opcional A mano Opzionale Met de hand Optie la main En option Hex Head Wrench Llave de cabeza hexagonal Security Wrench 2 Q9 09 Q YD Llave de seguridad Sechskantschl ssel Sicherheitsschl ssel Chave de cabeca sextavada Chave de seguran a Chiave esagonale Chiave di sicurezza Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Zeskantsleutel Veiligheidssleutel Cl t te hexagonale Cl de s curit Visit the InFocus support site at www infocus com support 3 SP WALLKIT 02 Installat
18. vers if necessary Insert one side of cover into groove and press down firmly on the cover on the other side until it snaps into the other groove See Figure 30 Figure 30 10 Slide outer cover of mount A back against mounting bracket See Figure 31 Visit the InFocus support site at www infocus com support Figure 31 11 Reinstall two 8 32 x 1 2 Phillips pan machine screws F through holes on sides of outer cover See Figure 32 Figure 32 13 SP WALLKIT 02 Installation Instructions Installation of Wall Bracket Covers NOTE If security screws are going to be used use the security screws V to install wall bracket covers See Security Screw Installation section for details 1 Place wall bracket top covers C over top of each wall bracket arm See Figure 33 projector arm not shown for display purposes Figure 33 2 Secure wall bracket top covers C to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 34 3 Place wall bracket bottom covers D over bottom of each wall bracket arm See Figure 33 4 Secure wall bracket bottom covers D to wall bracket arms by installing four 8 32 x 1 2 Phillips pan machine screws F through holes in covers and wall bracket See Figure 34 projector arm not shown for display purposes Figure 34 Ad
Download Pdf Manuals
Related Search