Home
Caliber MCD 265
Contents
1. Ne SSO NO EN 2 ISO CONNECTOR RCA Jack Line Out Red right White left SO CONNECTOR ANTENNA 01 03 05 07 CONNECTORA CONNECTOR 12 04 06 08 4 MEMORY 12V 05 07 5 AUTO ANTENNA OUTPUT 08 7 12V TO IGNITION KEY L WHITE R RED 8 GROUND Note connector A no 7 wire must be connected by car ignition key in order to avoid that car battery becomes weak when the car will be not used for long period CONNECTOR B 1 REAR RIGHT SPEAKER 2 REAR RIGHT SPEAKER FRONT RIGHT SPEAKER FRONT RIGHT SPEAKER FRONT LEFT SPEAKER FRONT LEFT SPEAKER REAR LEFT SPEAKER REAR LEFT SPEAKER ANDAR Maintenance FUSE REPLACEMENT If the fuse blows check the power connection and replace the fuse If the fuse blows again after the replacement there may be an internal malfunction In this case consult your nearest repairing center Warning Use the specified amperage fuse for each lead Use of a higher amperage fuse may cause serious damage INSTALLATION PRECAUTIONS Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver e Avoid installing the unit where it would be subject to high temperatures such as from direct sunlight or hot air from the heater or where it would be subject to dust dirt or excessive vibration e Use only the supplied mounting hardware for a safe and secure installation Be s
2. 24 1005 ONOFF LOUD ON OFF mode is selected by or knob The bass and treble response will be boosted MULTI CD SECTION MODE 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec CD MULT ONOFF CD MULTI ON OFF CD MULTI ON OFF mode is selected by or knob CD MULTI ON Read multi section CD CD MULTI OFF Read first section only BEEP MODE 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec SEEK ASK DP GED RETUNE EDC Eoo Eh 24 BEEP BEEP BEEP sound be heard from speaker when the buttons pressed SEEK MODE 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec SEL SEL SEL SEL SEL H SEL SEDHSEEK gt Q HSEEK1 SEEK 2 SEEK 1 When SEEK 1 mode is activated AUTO SEEK SCAN is stopped when station is detected even user still push SEEK button SEEK 2 Auto SEEK SCAN is not stopped even station is detected if user push SEEK button When release this SEEK button then stop when station is detected STEREO MONO 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec gt SEL SEL SEL SEL 2 SEL SEL H STEREO STEREO MONO When FM
3. 8 15 6V allowable Speaker Impedance 4 or 8 Ohm Output Power 75W x 4CH Note Specification and the design are subject to possible modification without notice due to improvements EN 10
4. in random instead of normal progression To cancel RANDOM mode press RDM button 22 again 23 24 10 TRACK DOWN UP SELECT In case of MP3 WMA files M5 10 Track down 6 10 Track EN 8 HOW SELECT MP3 WMA FILES A Searching by Track Press A PS then searching track is activated Press VOL knob then the first digit is blinking With VOL 53 VOL knob select first digit you want Press VOL knob then the first digit is fixed and second digit is blinking e With VOL VOL knob select 2 nd respectively Then automatically the song you selected will start B Searching by File Name e Press 5 twice then file search is activated Press VOL knob then the first directory is displayed With VOL VOL knob you can select the directory you want Press VOL knob again then the directory is fixed and the first file name is displayed With VOL VOL knob you can select the file you want Press VOL knob then the song you selected will start C Searching by Character e Press 5 3 times then character search mode is activated Press VOL knob then character is displayed With VOL VOL knob you can select the letter you want Press VOL knob longer than 2 sec The song which has same character you selected is displayed With VOL
5. stations are weak and are disturbed listening can be improved by selecting MONO LOCAL DX 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec SEL SEL SEL SEL gt SEL SEL LOCAL DX EN 6 Local position in areas with strong signals to let radio stop at only strong stations during manual tuning LOC appears Press to Distant position in areas with weak signals to listen to all stations PRESET STATIONS 1 2 3 4 5 6 A RADIO MODE When pressed short these keys select a preset station directly When pressed longer than 1 sec cur rent station is stored in preset memory bank When PTY mode is selected the PTY switch is shared as follows PTY music group PTY speech group OFF MUSIC SPEECH 1 POP M ROCK M NEWS AFFAIRS INFO 2 EASY M LIGHT M SPORT EDUCATE DRAMA 3 CLASSICS OTHER CULTURE SCIENCE VARIED 4 JAZZ COUNTRY WEATHER FINANCE CHILDREN 5 NATION M OLDIES SOCIAL RELIGION PHONE IN 6 OF OG FOLK M TRAVEL LEISURE DOCUMENT CD MP3 PLAYER MODE 1 PAUSE 2 INT 3 RPT 4 USING THE RDS FUNCTION What is RDS The RDS Radio Data System is a digital information system developed by the EBU European Broadcast Union Piggy backed on normal FM broadcasts RDS offers a variety of information services and automatic retuning functions for RDS compatible car stereos In 1988 RDS became availab
6. MCD265 INSTRUCTION MANUAL Car Stereo CD CDR CDRW MP3 WMA Player with PLL FM Stereo Radio Radio Data System with PTY USB Port and SD MMC Card Input Front AUX In Flip Down and Detachable Front Panel System LOCATION OF PARTS AND CONTROLS 00 0000 AnNNANNANAANN 4 1 6 POWER ON OFF 0 FUNCTION SELECT BUTTON BASS TREBLE BALANCE FADER SEEK MASK DPI RETUNE AUDIO DSP LOUDNESS CD MULTI BEEP SEEK STEREO LOCAL VOL UP VOL DOWN FOR BASS TREBLE BALANCE FADER PRESET STATIONS 1 2 3 4 5 6 AF FUNCTION ALTERNATIVE FREQUENCIES TA FUNCTION TRAFFIC ANNOUNCEMENT PTY FUNCTION PROGRAM TYPE DISPLAY BUTTON DISP MODE BUTTON MODE 0 BAND BUTTON BAND 1 AUTOMATIC OR MANUAL TUNING FREQ UP gt gt I OR FREQ DOWN 4 CD TRACK SEARCH BUTTON 12 AUTO SEEK SEARCH TUNING A PS 13 SCAN AUTOMATIC TUNING CONTROL SCAN 14 MUTE BUTTON MUT 15 LCD DISPLAY 16 PANEL RELEASE BUTTON 17 CD SLOT 18 CD EJECT BUTTON 19 PAUSE BUTTON 20 INTRO BUTTON Preview all Tracks 21 REPEAT BUTTON 22 RANDOM BUTTON 23 24 10 TRACK SEARCH DOWN UP 25 USB PORT 26 MULTI MEDIA CARD MMC SD CARD SLOT 27 FRONT AUX IN
7. SCAN mode 14 MUTE BUTTON MUT Press this button to mute the sound at once Press again to return to previous volume level 15 LCD DISPLAY The Liquid Crystal Display will display the current state of the unit 16 OPEN THE FRONT PANEL Press button and the front panel will open CD MP3 WMA CONTROL LOCATION OF PARTS TRACK SEARCH BUTTON 11 FORWARD AND REVERSE TRACK SEARCH or changing songs Press the SKIP button 4 or gt gt I during play to go to the desired track song 4 REVERSE FORWARD Press and hold the SKIP button 4 during play to scan the disc at high speed When the desired music section of the disc is found release the button Normal play will resume 17 CD SLOT 18 CD EJECT BUTTON Press the button to remove the CD 19 PAUSE BUTTON During PLAY press 19 PAU button to PAUSE Press it again to resume play 20 INTRO BUTTON Preview all Tracks When this button is pressed INT ON indication is displayed and the first several seconds of each track of the disc are played Press again to stop intro and listen to track 21 REPEAT BUTTON When this button is pressed RPT ON indication is displayed and play of the selected track will be continually repeated until the Track repeat mode is cancelled by pressing RPT button again 22 RANDOM BUTTON When this button is pressed RDM indication is displayed and each track of the disc are played
8. VOL knob you can select the song you want Press VOL knob then the song you selected will start Connecting it to Portable MP3 Player 25 USB Port Using USB cable to connect Your Portable MP3 Player 26 MULTI MEDIA CARD MMC SD CARD SLOT Support MP3 WMA 103 format music only IMPORTANT INFORMATION BECAUSE OF THE GREAT VARIETY OF PRODUCTS WITH USB SD AND MMC CARD PORTS AND THEIR SOMETIMES QUITE MANUFACTURER SPECIFIC FUNCTIONS WE CAN NEITHER GUARANTEE THAT ALL DEVICES WILL BE RECOGNIZED NOR THAT ALL OPERATING OPTIONS THAT ARE POSSIBLE IN THEORY WILL ACTUALLY WORK 27 FRONT AUX IN Convenient easy to use front AUX IN input jack allows easy connection of Portable Media digital MP3 Players RESET Reset button is placed on the housing J The reset button is to be activated for the following reason e Initial installation of the unit when all wiring is completed All the function button do not operate Error symbol the display a EN 9 TECHNICAL SPECIFICATIONS CD MP3 WMA PLAYER SECTION Signal to Noise Ratio gt 60 dB Channel Separation gt 50 dB 1kHz Frequency Response 20 Hz 20 kHz TUNER FM Frequency Range 87 5 108 MHz Intermediate Frequency 10 7 MHz Sensitivity 2 8 uV Stereo Separation 30 dB Signal to Noise Ratio 50 dB Channel Step 50 kHz LINE OUT Output 1 5 V max Impedance 10 k Ohm GENERAL Power Supply 12 V DC 10
9. eceive information for 5 sec the radio retunes to next station which has not the same station as the last station but has the TP information In TA seek mode the current station can be changed to the completely different station because the unit searches TP station when the field strength of the current station is very weak or the current station has no TP signal TAALARM mode Any automatic retune mode is not activated just can hear Beep sound MASK DPI 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec 24 SEL SEL MASK DPI gt DPI MASK ALL MASK DPI masked only the AF which has different MASK ALL masked the AF which has different and NO RDS signal with field strength RETUNE L S CONTROLS 2 When press the SEL button for more than 2 seconds it is activated as selecting Retune mode RETUNE L Select 90 seconds as the initial time of automatic TA search RETUNE S Select 30 seconds as initial time 2 sec 24 gt L RETUNE 5 AUDIO DSP CONTROLS 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec os CLASS FLAT DSP OFF 5 LOUDNESS CONTROLS 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function 2 sec
10. le in the United Kingdom France West Germany Ireland and Sweden Test transmissions are being conducted in many other european countries It is expected that RDS will be available in most western european countries in the near future 5 AF REG FUNCTION ALTERNATIVE FREQUENCIES When pressed short AF REG switching mode is selected When switching mode is selected the radio checks the signal strength of the AF all the time When pressed long it is activated as regional mode ON OFF Regional mode AF switching or PI SEEK is implemented to the station which have all PI codes same as current station REG segment is turned on in LCD display Regional mode OFF The regional code in the format of PI code is ignored when AF switching or SEEK is implemented TA FUNCTION TRAFFIC ANNOUNCEMENT When pressed short it is activated as TA mode on or off When TA mode is on and traffic announcement is transmitted When the unit is CD MP3 mode it will switch to radiomode temporarily If the volume level was under the threshold point it will be raised to the threshold point When TP station is received TP segment is turned on in LCD display PTY FUNCTION PROGRAM TYPE PTY MUSIC PTY SPEECH PTY OFF While selecting PTY type its selection is implemented by preset buttons as described in preset key When PTY is selected the radio starts to search corresponding PTY information and
11. stops if the cor responding PTY information is detected DISPLAY DISP Press DISP button to switch between display informations such as radio frequencies clock track and other informations depending on the playing MODE MODE BUTTON MODE By pressing this key user can select AUX TUNER CD MP3 USB or MMC SD mode EN 7 10 BAND BUTTON BAND Each band is toggled cyclically by pressing this key FM1 FM2 FM3 11 AUTOMATIC OR MANUAL TUNING FREQ UP gt gt I OR FREQ DOWN 4 A RADIO MODE When pressed short these keys are operated as MANUAL tuning mode When pressed longer than 1 sec they are operated as SEEK tuning mode B CD MP3 WMA PLAYER MODE When pressed short they are operated as TRACK UP or TRACK DOWN mode When pressed longer than 1 sec they are operated as CUE or REVIEW mode 12 AUTO SEEK SEARCH TUNING A PS By pressing shortly the radio searches for each preset station When field strength level is bigger than the threshold level of stop level the radio is holding at that preset number for 5 sec with releasing mute and than searches again By pressing longer than 1 sec and then 6 strongest stations are preset to the corresponding preset number When AS operation is finished the radio executes the preset scan 13 SCAN AUTOMATIC TUNING CONTROL SCAN This key is operated as RADIO SCAN The operation is similar as normal search but different thing is holding 5 seconds on every station detected in RADIO
12. t In order to prevent this from happening detach the front panel by pressing the button and clean the connector from time to time Swab Clean the connector with a cotton swab together with contact cleaner as illustrated Be sure to clean them carefully pin by pin and make sure not to damage the connecting points EN 4 Main unit Rear of front panel OPERATION INSTRUCTIONS 1 POWER ON OFF By pressing this key the unit is on and off This unit is turned on by pressing any key 2 3 FUNCTION SELECT BUTTON BASS TREBLE BALANCE FADER SEEK MASK DPI RETUNE AUDIO DSP LOUDNESS CD MULTI BEEP SEEK STEREO LOCAL Turning the VOL knob Right or Left 3 you can adjust VOL BASS TREB BAL FAD To select other functions press the VOL knob shortly until the desired functions is shown on the display Figure 1 shows how control functions are selected using the VOL knob Fig 1 Selection of sound control functions 1 VOL 2 SEL 3 BAS 4 TRE 5 BAL 6 FAD Turning the VOL knob Right or Left Increase or decrease the volume by turning or These buttons can be used to adjust the BASS TREBLE BALANCE and FADER TA ALARM 2 When press the SEL button for more than 2 seconds it is activated as selecting mode of these function ro A TA SEEK Mode TA ALARM mode is selected by or knob 2 sec 7 4 SEEK SEEK ALARM SEEK mode When newly turned station does not r
13. ure to remove the front panel before installing the unit 182mm NOTE Inclination angle for car radio installation must not exceed 30 otherwise the front panel will not open 53mm release screw and bracket claws if necessay Note Keep the release key in the safe place as you may need it in future to remove the unit from the car EN 3 SUPPORT THE UNIT UNIT RELEASE CASE DASH BOARD HEX NUT LOCK WASHER PLAIN WASHER CAR BODY REAR SUPPORT STRAP TAPPING SCREW 0 5 X 15 HEX BOLT Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent the unit from being stolen FOLDING DOWN AND DETACHING ATTACHING THE FRONT PANEL Before detaching the front panel be sure to press the 0 button 1 OFF first Then press the button 16 let the Front Panel arrive horizontal position and detach the panel by pulling it towards you as illustrated Notes Donotpress the front panel hard against the unit when attaching it It can be easily attached by press ing it lightly against the unit When you carry the front panel with you put it in the supplied front panel case Do not press hard or give excessive pressure to the display window of the front panel when attaching it to the unit CLEANING THE CONNECTOR The unit may not function properly if the connectors between the unit and the front panel are contaminated with dir
Download Pdf Manuals
Related Search
Related Contents
NOTICE OF APPROVAL — AVIS D`APPROBATION MANUAL INSTALACIÓN LINUX Goldstar GWHD5000 Owner's Manual Manuale istruzioni SERVICE MANUAL Instruction Manual - Videology Imaging Solutions, Inc. Xerox B1 User's Manual Amana Air Conditioner ASX 14 SEER User's Manual Massive Wall light 37467/43/10 Copyright © All rights reserved.
Failed to retrieve file