DeLonghi ESAM5600 coffee maker
Contents
1. The appliance gives off heat After positioning the appliance on the worktop leave a space of at least 3 cm between the surfaces of the appliance and the side and rear walls and at least 15 cm above the coffee maker Water penetrating the coffee maker could cause damage Do not place the appliance near taps or sinks The appliance could be damaged if the water it contains freezes Do not install the coffee maker in a room where the temperature could drop below free zing point Arrange the power cable in such a way that it cannot be damaged by sharp edges or contact with hot surfaces e g electric hot plates 10 Connecting the appliance Important Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10A only If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified pro fessional Setting up the appliance NB Coffee has been used to factory test the appliance and it is therefore completely nor mal for there to be traces of coffee in the mill The coffee maker is however guaranteed to be new You should customise water hardness as soon as possible following the instructions in the section Setting water hardness on page 20 1 Plug the appliance into t2. A Important Danger of burns When clea ning the internal tubes of the milk container a litt le hot water leaks out of the milk spout B5 Avoid contact with splashes of water When Press CLEAN button flashes on the display each time you use a milk function 1 Leave the milk container in the machine you do not need to empty it 2 Place a cup or other recipient under the milk spout fig 20 3 Press the CLEAN button fig 29 and keep it pressed until the progress bar displayed toge ther with the message CLEANIN is comple te 4 After cleaning remove the milk container and always clean the nozzle with a sponge fig 30 g NB When Press CLEAN button flashes on the display you can still prepare any type of cof fee or milk If you have to make a number of drinks with milk wait until you have delivered the last cup before cleaning the container The milk left in the container can be kept in the refrigerator Programming the quantities of coffee and milk in the cup The machine leaves the factory set to delivery standard quantities To change these quantities proceed as follows 1 Attach the milk container see Filling and attaching the milk container place a cup under the coffee spouts and milk spout fig 20 2 Press the icon corresponding to the function you want to programme until PROGRAM QUANTITY Milk for is displayed and the icon corresponding to the selected function f
3. The coffee maker is now reprogrammed with the new water hardness setting TECHNICAL SPECIFICATION Voltage 220 240 V 50 60 Hz 10A max Absorbed power 1350W Pressure 15 bar Water tank capacity 1 7 litres Size LxHxP 272x374x441 mm Weight 11 5 Kg The appliance complies with the following EC directives ex Voltage Directive 2006 95 EC MC Directive 89 336 EEC and subsequent amendments 92 31 EEC and 93 68 EEC Materials and accessories coming into contact with food conform to EC regulation 1935 2004 DISPOSAL Electrical appliances must not be disposed of as household waste Appliances with this symbol are covered by European Directive 2002 96 EC All unused electric and electronic appliances must be disposed of separately from household waste by taking them to the special centres provided by the State Disposing of the unused appliance cor rectly avoids damage to the environment and a risk to health For more information on disposing of the unused appliance contact your local autho rity waste disposal department or the shop where the appliance was bought 21 DISPLAYED MESSAGES DISPLAYED MESSAGE FILL TANK DD GROUND TOO FINE ADJUST MILL Insert water spout and press ok POSSIBLE CAUSE The water tank is empty or positioned incorrectly The machine cannot make Coffee as there is air in the hydraulic circuit The grinding is too fine and the coffee is delivered too slowly
4. Until the grounds container has been cleaned the appliance continues to display the message and coffee cannot be made To clean with the machine on open the service door on the front of the appliance fig 32 extract the drip tray fig 33 empty and clean Empty the grounds container and clean tho roughly to remove all residues left on the bot tom A Important When removing the drip tray the grounds container must be emptied even if it is not completely full If this is not done when you make the next cof fees the grounds container may fill up more than expected and clog the machine Cleaning the drip tray A Important f the drip tray is not emptied regularly the water could overflow from the edge and seep inside or around the coffee maker This could damage the machine the surface it rests on or the surrounding area The drip tray is fitted with a level indicator red showing the level of water it contains fig 34 Before the indicator protrudes from the cup tray the drip tray must be emptied and cleaned To remove the tray 1 Open the service door fig 32 2 Remove the drip tray and the grounds contai ner fig 33 3 Empty the drip tray and grounds container and wash them 4 Remove the drip tray complete with grounds container A9 5 Close the service door Cleaning the water tank 1 Clean the water tank A7 regularly about once a month with a damp cloth and a litt
5. 1 Position a container under the spout 2 Press thegBicon the appliance starts delive ring hot water until the message HOT WATER PROGRAM QUANTITY is displayed 17 and the AR icon flashes then release 3 When tHe hot water in the cup reaches the required level press the icon again The machine is now reprogrammed with the new quantity CLEANING AND MAINTENANCE Cleaning the coffee maker The following parts of the machine must be clea ned regularly coffee grounds container A9 drip tray A12 water tank A7 hot water and steam nozzle A16 coffee spouts A15 pre ground coffee funnel A4 Inside the machine accessible after opening the service door A13 infuser AB milk container B touch screen C A Important Do not use solvents abrasive detergents or alcohol to clean the coffee maker With De Longhi superautomatic coffee makers you need not use chemical products to clean the appliance The descaler recommended by De Longhi is made from natural and completely biodegra dable substances None of the components of the appliance can be washed in a dishwasher with the exception of the milk container B Do not use metal objects to remove encrusta tions or coffee deposits as they could scratch metal or plastic surfaces Cleaning the coffee grounds container When EMPTY GROUNDS CONTAINER is displa yed the grounds container must be emptied and cleaned
6. Milk has been delivered recently and the tubes inside the milk container must be cleaned Press the CLEAN button and keep it pressed until the pro gress bar which appears on the display together with the message Cleaning is com plete Press OK The inside of the appliance is very dirty The initial priming of the machine has not been com pleted successfully 23 Press the icon corresponding to OK until a new message is displayed Then clean the inside of the appliance tho roughly as described in the section Cleaning Repeat the setting up opera tions TROUBLESHOOTING Below is a list of some of the possible malfunctions If the problem cannot be resolved as described contact customer services PROBLEM The coffee is not hot POSSIBLE CAUSE The cups have not been preheated The infuser has cooled down because 2 3 minutes have elapsed since the last coffee was made REMEDY Warm the cups by rinsing them with hot water using the hot water function Before making coffee heat the infuser by pressing the g icon see section Manual rinsing The coffee is not creamy enough The coffee is ground too coarsely Wrong type of coffee Turn the grinding adjustment knob one click anticlockwise towards 1 while the coffee mill is in operation fig 8 Continue one click at a time until coffee delivery is sati sfactory The effect is only visible after making 2 c
7. Press the icon to confirm or the P icon to cancel the operation 6 The appliance is automatically ready for use again Piena Setting water hardness For instructions on setting water hardness see page 20 Pan Setting display contrast To increase or reduce the contrast of the display proceed as follows 1 Choose the SETTINGS section as described above 2 Press the selection icons lt or gt until DIS PLAY CONTRAST is displayed 3 Press the icon to confirm 4 Press the selection icons lt or gt until the required contrast is displayed the progress bar indicates the level of contrast selected 5 Press the icon to confirm or the P icon to cancel the operation 6 The appliance is automatically ready for use again Pad Activating deactivating the beep This activates or deactivates the beep emitted by the machine each time an icon is pressed or an accessory is inserted removed The beep is acti ve by default 1 Choose the SETTINGS section as described above 2 Press the selection icons lt or gt until BEEP Enabled or Disabled is displayed 3 Press the zp icon to confirm Disable or Enable is displayed 4 Press the icon to deactivate the function BEEP Disabled o Beep Enabled is displa yed 12 The appliance is automatically ready for use again Aa Resetting factory default values reset This resets all menu settings and prog
8. REMEDY Fill the tank with water and or insert it correctly pushing it as far as it will go until it clicks into place Press the corresponding icon and deliver water from the spout until the flow is conti nuous and regular Turn the grinding adjustment knob one click clockwise towards 7 while the coffee mill is in operation The effect is only visible after making 2 coffees If delivery is still too slow repeat the correction proce dure turning the grinding adjustment knob another click until delivery is correct INSERT WATER SPOUT The water spout is not inser ted or is inserted incorrectly Insert water spout as far as it will go EMPTY GROUNDS CONTAINER ra The grounds container is too full or more than 3 days have passed since you last made coffee this guarantees cor rect hygiene of the machine Empty the grounds container and clean then replace Important when removing the drip tray the grounds container MUST be emptied even if it is not completely full If this is not done when you make the next coffees the grounds container may fill up more than expected and clog the machine INSERT GROUNDS CONTAI NER D After cleaning the grounds container has not been repla ced Open the service door and insert the grounds container INSERT MILK CONTAINER The milk container is not inserted Insert milk container DESCALE The machine must be desca l
9. 4 Place a cup under the coffee spouts 4 Press the 1 cup coffee icon X2 fig 12 The selected quantity and Ground taste are dis played 5 Preparation begins A cup appears on the dis play and gradually fills as preparation pro gresses po 15 g NB While the machine is making coffee delivery can be interrupted at any moment by pressing the lit cup icon Once the coffee has been made the appliance is ready to use again g NB See the tips in the section above MAKING DRINKS WITH MILK Filling and attaching the milk container 1 Turn the lid of the milk container clockwise until it becomes noticeably difficult to turn then remove fig 15 2 Fill the milk container with a sufficient quan tity of milk not exceeding the MAX level mar ked on the handle fig 16 g NB Do not use full fat milk Use skimmed or semi skimmed milk at refrigerator temperature about 5 C To avoid milk with poor froth or large bubbles always clean the milk container lid and hot water nozzle as described in the section Cleaning the milk container 3 Make sure the milk intake tube is correctly inserted in the bottom of the milk container lid fig 17 4 Replace the milk container lid and turn anti clockwise as far as it will go 5 Remove the hot water spout from the nozzle fig 18 6 Attach the container to the nozzle pushing as far as it will go fig 19 7 Place a sufficiently large cup under t
10. COFFEE AND CAPPUCCINO MAKER ESAM5600 INDEX INTRODUCTION Symbols used in these instructions Letters in brackets Troubleshooting and repairs SAFETY Fundamental safety warning Designated us Instructions DESCRIPTION Description of appliance Description of milk containe Description of control panel graphic touch screen Meaning of animations BEFORE USE Controls after transport Installing the appliance Connecting the appliance Setting up the appliance TURNING THE APPLIANCE ON TURNING THE APPLIANCE OFF 11 CHANGING THE MENU SETTINGS Setting the language Setting the temperature Setting water hardness Setting display contrast Activating deactivating the beep Resetting factory default values reset Descalint Statistics function Setting the clock Setting auto start time Setting auto off MAKING COFFEE Selecting the coffee taste Selecting the quantity of coffee in the cup Programming the my coffee quantity Adjusting the coffee mill Manual rinsing Making coffee using coffee beans Making coffee using pre ground coffee MAKING DRINKS WITH MILK Filling and attaching the milk container Making cappuccino Making caffelatte Making macchiato Preparing milk Cleaning the milk contai
11. ER HARDNESS The DESCALE message is displayed after a period of time established according to water hardness The coffee maker is set by default for a hardness value of 4 very hard water The machine can also be programmed according to the hardness of the mains water in the various regions varying the frequency with which the message is displayed Measuring water hardness 1 Remove the TOTAL HARDNESS TEST indica tor paper from its pack 2 Immerse the paper completely in a glass of water for about a second 3 Remove the paper from the water and shake lightly After about a minute 1 2 3 or 4 red squares form depending on the hardness of the water Each square corresponds to one level 10 1 1 D 13 20 Setting water hardness 1 Choose the MAINTENANCE soft water Level 000 if slightly hard water Level oO HN hard water Level 0000 gt HI very hard water Level coso MENN 3 section as described in the section Changing the menu settings 3 Press the selection icons until WATER HARD NESS is displayed 2 Turn the selection dial to select WATER HARDNESS Press the icon to confirm Press the selection icons to set the level cor Tespondinggtp the water hardness identified by the indicator paper see figure in previous section 5 Press the icon to confirm the setting 6 The appliance is automatically ready for use again D
12. ection icon C10 until the quan tity bar has filled as follows Ab Corresponding Quantity in Quantity bar coffee cup ml NN core EXTRA SHORT ASOR ag SHORT COFFEE 40 STANDARD COFFEE 60 LONG COFFEE 90 EXTRA LONG COFFEE ala The quantity bar fills up progressively each time you press the selection icon C10 Programming the my coffee quantity The appliance is set by default to automatically deliver 30 ml of my coffee To modify these settings proceed as follows 1 Place a cup under the coffee spouts fig 10 2 Press the selection icon C10 repeatedly until My coffee and the empty bar are displayed 3 Press the 1 cup ZZ icon fig 12 until MY COFFEE PROGRAM QUANTITY and the uz symbol are displayed The machine starts delivering the coffee and the SZ icon flashes 4 As soon as the coffee in the cup reaches the required level press the 2 icon again The quantity set has now been programmed Adjusting the coffee mill The coffee mill is set by default to prepare coffee correctly and should not require adjusting initially However if after making the first few coffees you find that delivery is either too fast or too slow a drop at a time this can be corrected by adjusting the grinding adjustment knob fig 8 14 These adjustments will only be evident after at least 2 cups of coffee have been made g NB The grinding adjustment knob must onl
13. ection is divi ded into groups as described below SETTINGS Language Coffee temperature Water hardness Display contrast Beep Default values MAINTENANCE Descaling Statistics CLOCK Adjust time Auto start Auto of To access the required section press the P icon and use the selection icons C4 and C10 to scroll until the image you want is displayed Then press the icon to confirm or press the P icon again to exit g NB When navigating in the programming menu and you want to exit press the P icon a number of times Setting the language To modify the language on the display proceed as follows 1 Choose the SETTINGS section as described above 2 Press the selection icons lt or gt until LAN GUAGE is displayed 3 Press the icon to confirm 4 Press the selection icons lt or gt until the required language is displayed 5 Press the 3 icon to confirm or the P icon to cancel the operation 6 The appliance is automatically ready for use again Pad Setting the temperature To modify the temperature low medium high of the water used to make the coffee proceed as fol lows 1 Choose the SETTINGS section as described above 2 Press the selection icons lt or gt until COFFEE TEMPERATURE is displayed 3 Press the icon to confirm 4 Press the selection icons lt or gt until the required temperature low medium or high is displayed 5
14. ed 22 The descaling procedure described in the Descaling section needs to be perfor med as soon as possible DISPLAYED MESSAGE ADD GROUND COFFEE POSSIBLE CAUSE The pre ground coffee func tion has been selected without placing any pre ground coffee in the funnel The funnel is clogged REMEDY Place pre ground coffee in the funnel and press the y icon Empty the funnel with the help of a plastic knife as described in the section Cleaning the pre ground cof fee funnel LESS COFFEE Too much coffee has been used Select a milder taste or reduce the quantity of pre ground coffee then make the coffee again FILL BEANS CONTAINER amp The coffee beans have run out The pre ground coffee funnel is clogged Fill beans container Empty the funnel with the help of a plastic knife as described in the section Cleaning the pre ground cof fee funnel INSERT INFUSER ASSEMBLY The infuser has not been replaced after cleaning Insert the infuser as descri bed in the section Cleaning the infuser CLOSE Di OR E The service door is open Close the service door GENERAL ALARI The inside of the appliance is very dirty Clean the inside of the appliance thoroughly as described in the section Cleaning If the message is still displayed after cleaning contact Customer Services Press CLEAN button
15. forms an automatic preheat and rinse cycle which can not be interrupted A drop animation indicates that rinsing is under way see section Meaning of animations The appliance is ready for use only after comple tion of this cycle A Danger of burns During rinsing a little hot water comes out of the coffee spouts and is collected in the drip tray underneath Avoid contact with splashes of water Toturn the appliance on press the button on the right of the touch screen 0 fig 5 The appliance begins the heating Cycle indicated by a thermometer icon fig 7 which fills as the cycle advances Once heating is complete the appliance shows the time set and the coffee taste and quantity selection bars set to the standard values stan dard quantity and taste The machine is now ready for use TURNING THE APPLIANCE OFF Each time the appliance is turned off it performs an automatic rinse cycle which cannot be inter rupted Danger of burns During rinsing a little hot water flows from the coffee spouts Avoid contact with splashes of water To turn the appliance off press the 1 button fig 5 The appliance performs the rinse cycle then goes off NB If the appliance is not used for a long period place the main switch on the back of the appliance in the 0 position fig 6 CHANGING THE MENU SETTINGS The programming menu is divided into 3 sections indicated by different icons Each s
16. he coffee spouts A14 and the milk spout B5 If necessary move the milk spout slightly out wards fig 20 8 To use particularly tall cups glasses raise the lid of the special compartment in the cup tray fig 21 Making cappuccino After attaching the milk container see the section Filling and attaching the milk contai ner position the frothed milk regulator on CAPPUCCINO fig 22 The quality of froth can be adjusted during delivery by moving the regulator slightly towards LATTE for a denser froth Moving it towards CAPPUCCINO obtains a less dense froth 2 Press the CAPPUCCINO icon fig 23 A cup is displayed and gradually fills as preparation progresses After a few seconds frothed milk flows out of the milk spout into the cup below The milk stops automatically and delivery of coffee begins 3 At the end of delivery the machine is automa tically ready for use again g NB If during delivery you want to stop pre paring milk press the CAPPUCCINO icon or inter rupt preparation of the coffee by pressing the sz icon Making latte After attaching the milk container see the section Filling and attaching the milk contai ner position the frothed milk regulator B1 on LATTE fig 24 2 Press the LATTE icon fig 25 A glass is displayed and gradually fills as pre paration progresses After a few seconds milk is delivered from the milk spout into the cup below The milk stops automatical
17. he mains socket and place the main switch on the back of the appliance in the position fig 1 You must first choose the language the langua ges scroll through at intervals of about 3 seconds 2 When Italian appears press the selection icon corresponding to OK on the display for a few seconds fig 2 Once the language has been saved the message English installed appears Follow the instructions indicated by the appliance 3 FILL TANK remove the water tank fill to the MAX line with fresh water then replace in the appliance fig 3 4 If the water spout is not fitted to the applian ce INSERT WATER SPOUT is displayed Insert the spout fig 4 5 Place a container with a minimum capacity of 100 ml under the spout 6 PRESS OK then press the icon correspon ding to OK on the display fig 2 Please Wait is displayed and the appliance begins to deliver water The appliance ends the first start up procedure then the message Turning off Please wait is displayed and the appliance goes off The coffee maker is now ready for normal use g NB When using the appliance for the first time you need to make 4 5 cups of coffee and 4 5 cappuccinos before it starts to give satisfactory results TURNING THE APPLIANCE ON g NB Before turning the appliance on make sure the main switch on the back of the appliance is in the position fig 1 Each time the appliance is turned on it per
18. i de the holes and the groove on the fine end of the frothed milk regulator 19 5 Use a brush not metal to remove residues from the milk hole 6 Check that the intake tube and milk spout are not clogged with milk residues 7 Replace the frothed Ai milk regulator milk spout and intake tube 8 Replace the lid on the milk container turning it anticlockwise as far as it will go to hook it in place DESCALING Descale the machine when the message DESCA LE flashes on the display Frothed milk regulator Milk hole Important Descaler contains acids which may irritate the skin and eyes It is vital to adhere to the manufacturers safety warnings given on the descaler pack and the warnings relating to the pro cedure to follow in the event of contact with the skin and eyes NB Use De Longhi descaler only Under no circumstances should you use sulphamic or ace tic based descalers Their use invalidates the gua rantee Failure to descale the appliance as descri bed also invalidates the guarantee 1 Turn the machine on 2 Choose the MAINTENANCE section as describe in the section Changing the menu settings 3 Press the selection icons until DESCALING is displayed 4 Press the 9 icon to confirm OK to confirm is displayed Press the icon again to activate the function 5 The message ADD DESCALER Press OK is displayed 6 Before confirming empty the water tank A7 Add the de
19. ion icons lt or gt to modify the hours 5 Press the 2 icon to confirm or the P icon to cancel the operation The minutes flash on the display 6 Press the selection icons lt or gt to modify the section as p apa minutes 7 Press the icon to confirm or the P icon to cancel the operation The time is now set and the appliance is automa tically ready for use again Setting auto start time You can set the auto start time in order to have the appliance ready at a certain time for example in the morning so you can make coffee immedia tely 1 Choose the CLOCK section as described above 2 Press the selection icons lt or gt until AUTO START Disabled is displayed 3 Press the icon to select Enable is dis played and the hours flash on the display 4 Press the selection icons lt or gt to modify the hours 5 Press the icon to confirm The minutes flash on the display 6 Press the selection icons lt or gt to modify the minutes 7 Press the 3 icon to confirm Auto start ena bled is displayed 8 The appliance is automatically ready for use again The i symbol appears next to the clock to indicate that auto start has been pro grammed To deactivate the function 1 Choose the CLOCK section as described above 2 Press the selection icons lt or gt until AUTO START Enabled is displayed 3 Press the icon to select Disable i
20. lashes 3 Release the icon The appliance starts delive ring milk 4 When the required quantity of milk has been delivered into the cup press the icon corre sponding to the selected function again 5 After a few seconds the appliance starts deli vering coffee into the cup the message PRO GRAM QUANTITY Coffee for is displayed with the exception of the MILK function and the or icon flashes 6 As soon as the coffee in the cup has reached the required quantity press the CZ icon Coffee delivery stops The machine is now reprogrammed with the new quantities PREPARING HOT WATER Preparation LAN coped Danger of burns Never leave the coffee maker unsupervised while delivering hot water The hot water spout becomes hot while water is being delivered and must be held by the handle only 1 Make sure the hot water spout B7 is atta ched correctly fig 4 2 Place a container under the spout as close as possible to avoid splashes 3 Press the icon fig 31 Preparation begins HO WATER and the corresponding animation are displayed 4 To interrupt delivery of hot water manually press the icon again 5 Once the cbffee has been made the appliance prepares for use again Important You should not deliver hot water for more than 2 minutes at a time Changing the quantity The appliance is set by default to automatically deliver 250ml To modify these quantities pro ceed as follows
21. le mild washing up liquid 2 Clean to remove all washing up liquid resi dues then rinse the water tank thoroughly Cleaning the coffee spouts 1 Clean the coffee spouts with a sponge or cloth fig 35 2 Check the holes in the coffee spout are not blocked If necessary remove coffee deposits with a toothpick fig 36 18 Cleaning the hot water nozzle Clean the hot water nozzle regularly using a spon ge or cloth fig 30 Cleaning the pre ground coffee funnel Check regularly about once a month that the pre ground coffee funnel is not blocked If necessary remove coffee deposits with a plastic knife Cleaning the inside of the coffee maker Danger of electric shock Before cleaning internal parts the machine must be turned off and unplugged from the mains power supply Never immerse the coffee maker in water 1 Check regularly about once a week that the inside of the appliance is not dirty If neces sary remove coffee deposits with a knife and a sponge 2 Remove the residues with a vacuum cleaner fig 37 Cleaning the infuser The infuser must be cleaned at least once a month LN important The infuser A8 must not be removed when the appliance is on Do not attempt to use force to remove the infuser as this could damage the coffee maker 1 Make sure the machine is correctly turned off see Turning the appliance off Open the service door fig 32 Remove the drip tray and grou
22. ly and delivery of coffee begins 3 Atthe end of delivery the machine is automa tically ready for use again g NB If during delivery you want to stop pre paring milk press the LATTE icon or interrupt pre paration of the coffee by pressing the KZicon u flat white After attaching the milk container see the section Filling and attaching the milk contai ner position the frothed milk regulator B1 on FLAT WHITE fig 26 printed on the milk container lid 2 Press the FLAT WHITE icon fig 27 A glass is displayed and gradually fills as pre paration progresses After a few seconds frothed milk comes out of the milk spout into the glass below The milk stops automatically and delivery of coffee begins 3 Atthe end of delivery the machine is automa tically ready for use again g NB If during delivery you want to stop pre paring milk press the FLAT WHITE icon or inter rupt preparation of the coffee by pressing Szthe icon Me hot milk After attachin the milk container see the section Filling and attaching the milk contai ner position the frothed milk regulator on CAFFELATTE fig 22 2 Press the HOT MILK icon fig 28 A glass is displayed and gradually fills as preparation progresses 3 Atthe end of delivery the machine is automa tically ready for use again g NB If during delivery you want to stop pre paring milk press the HOT MILK icon once Cleaning the milk container after use
23. nds container fig 33 4 Press the two red release buttons inwards and at the same time pull the infuser outwards fig 38 2 3 A Important Do not use washing up liquid to clean the infuser It would remove the lubricant applied to the inside of the piston causing the infuser to seize up and become unusable 5 Soak the infuser in water for about 5 minutes then rinse under the tap 6 After cleaning replace the infuser by sliding it onto the internal support and pin at the bot tom then push the PUSH symbol fully in until it clicks into place gt Support g NB If the infuser is difficult to insert you must first adapt it to the right dimension by pressing it forcefully from the bottom and top as shown in the figure 7 Once inserted make sure the two red buttons have snapped out 8 Replace the drip tray and grounds container 9 Close the service door Cleaning the milk container Clean the milk container each time you prepare milk as described below 1 Turn the milk container lid clockwise then remove it Remove the milk spout and intake tube Remove the frothed milk regulator by pulling it outwards 4 Wash all the compo 2 3 nents thoroughly with hot water and mild washing up MKspout liquid All compo nents can be washed milk intake in a dishwasher pla tube g cing them in the top basket of the dishwasher Make sure there are no milk residues left ins
24. ner after use Programming the quantities of coffee and milk in the cup PREPARING HOT WATER Preparation Changing the quantity CLEANING AND MAINTENANCE Cleaning the coffee maker Cleaning the coffee grounds container Cleaning the drip tray Cleaning the water tank Cleaning the coffee spouts Cleaning the hot water nozzle Cleaning the pre ground coffee funnel Cleaning the inside of the coffee make Cleaning the infuser Cleaning the milk containe DESCALING SETTING WATER HARDNESS Measuring water hardness Setting water hardness TECHNICAL SPECIFICATION DISPOSAL DISPLAYED MESSAGES TROUBLESHOOTING INTRODUCTION SAFETY Thank you for choosing the ESAM 5600 automa tic coffee and cappuccino maker We hope you enjoy using your new appliance Take a few minutes to read these instructions This will avoid all risks and damage to the machi ne Symbols used in these instructions Important warnings are identified by these symbols These warnings must absolutely be respected A Danger Failure to observe the warning could result in pos sibly life threatening injury from electric shock N Important Failure to observe the warning could result in injury or damage to the appliance LN vanger of burns Failure to observe the warning could result in scalds or burns g NB This symbol identifies important advice or i
25. nfor mation for the user Letters in brackets The letters in brackets refer to the legend in the description of the appliance on page 3 Troubleshooting and repairs In the event of problems first try and resolve them following the information given in the sec tions Displayed messages on page 22 and Troubleshooting on page 24 If this does not resolve the problem or you requi re further information you should consult Customer Services by calling the number given on the annexed guarantee leaflet If your country is not among those listed in the leaflet call the number given in the guarantee If repairs are required contact De Longhi Customer Services only The addresses are given in the guarantee leaflet provided with the machine Fundamental safety warnings A Danger This is an electrical appliance and may cause electric shock You should therefore respect the following safety warnings Never touch the appliance with damp hands Never touch the plug with damp hands Make sure the socket used is freely accessible at all times enabling the appliance to be unplugged when necessary Unplug directly from the plug only Never pull the power cable as you could damage it To disconnect the appliance completely place the main switch at the back of the appliance in the 0 position fig 6 If the appliance is faulty do not attempt to repair Turn it off unplug from the mains soc ket and contact Cust
26. offees Use a type of coffee for espresso coffee makers The coffee is delivered too slowly or a drop at a time The coffee is ground too finely Turn the grinding adjust ment knob one click clock wise towards 7 while the coffee mill is in operation fig 8 Continue one click at a time until coffee deli very is satisfactory The effect is only visible after making 2 coffees The coffee is delivered too quickly The coffee is ground too coarsely 24 Turn the grinding adjust ment knob one click anti clockwise towards 1 while the coffee mill is in opera tion fig 8 Avoid turning the grinding adjustment knob excessively otherwise when you select 2 cups the coffee may be delivered a drop at a time PROBLEM Coffee does not come out of one or both the spouts POSSIBLE CAUSE The spouts are blocked REMEDY Clean the spouts with a toothpick The coffee does not come out of the spout but around the service door A12 The holes in the spouts are clogged with dry coffee dust The coffee guide A21 insi de the service door is bloc ked and cannot swing Clean the spouts with a toothpick sponge or kit chen brush Thoroughly clean the coffee guide A21 particularly near the hinges Water comes out of the spouts instead of coffee The pre ground coffee may be blocked in the funnel A4 Clean the funnel A4 as described in the section Cleaning the pre gr
27. omer Services Ifthe plug or power cable is damaged it must be replaced by De Longhi Customer Services only to avoid all risk A Danger Keep all packaging plastic bags polystyrene foam away from children A Danger Do not allow the appliance to be used by persons including children with psycholo gical physical or sensory impairments or with ina dequate experience or knowledge unless closely supervised and instructed by someone responsible for their safety Children must be supervised to ensure they do not play with the appliance A Important Risk of burns This appliance produces hot water and steam may form while it is in operation Avoid contact with splashes of water or hot steam When the appliance is in operation do not touch the cup warmer shelf A6 as it becomes hot Designated use This appliance is designed and made to prepare coffee and heat drinks All other use is considered improper This appliance is not suitable for com mercial use The manufacturer is not liable for damage deriving from improper use of the appliance This is a household appliance only It is not suitable for use in staff kitchen areas in shops offices and other working environments farm houses by clients in hotels motels and other residen tial type environments bed and breakfast type environments Instructions Read these instructions carefully before using the appliance Failure to follow these inst
28. ound coffee funnel The milk does not come out of the milk spout B5 The intake tube is not inser ted or is inserted incor rectly Insert the intake tube B4 in the rubber washer in the milk container lid fig 20 The milk is not well frothed The milk container lid is dirty The frothed milk regulator is incorrectly adjusted Clean the milk container lid as described in the section Cleaning the milk contai ner Adjust following the instructions in the section Making drinks with milk The milk contains bubbles or squirts out of the milk spout The milk is not cold enough or is not semi skimmed The frothed milk regulator is incorrectly adjusted The milk container lid is dirty You should ideally use skimmed or semi skimmed milk at refrigerator tempe rature about 5 C If the result is still disappointing try another brand of milk Move the frothed milk regu lator slightly towards the word CAFFELATTE see section Making cappucci no Clean the milk container lid as described in the section Cleaning the milk contai ner The appliance does not come on It is not plugged into the mains socket The main switch is not tur ned on 25 Plug into the mains socket Place the main switch on the back of the appliance in the position
29. rammed quantities back to the default values with the exception of the language which remains as set 1 Choose the SETTINGS section as described above 2 Press the selection icons lt or gt until DEFAULT VALUES is displayed 3 Pressthe icon to confirm OK to confirm is displayed 4 Pressthe _ icon to return to the original set tings or t amp P icon to cancel the operation The appliance is automatically ready for use again with the default settings AM Descaling For instructions on descaling see page 19 AN Statistics function This displays statistics relating to the machine To display proceed as follows 1 Choose the MAINTENANCE described above Press the selection icons lt or gt until STATI STICS is displayed Press the icon to confirm Press the selection icons lt or gt to verify how many coffees have been made how many drinks with milk have been made how many times the machine has been desca led the total number of litres of water delivered 5 Press the icon and the appliance is auto matically ready for use again or the P icon to cancel the operation LAD Setting the clock To adjust the time on the display proceed as fol lows 1 Choose the CLOCK section as described above 2 Press the selection icons lt or gt until ADJUST TIME is displayed 3 Press the icon to confirm The hours flash on the display 4 Press the select
30. ructions may result in burns or damage to the appliance The manufacturer is not liable for damage deriving from failure to follow these instruc tions g NB Keep these instructions If the appliance is passed to other persons they must also be pro vided with these instructions DESCRIPTION Description of appliance page 3 A Al rinding adjustment knob A2 Beans container lid A3 Beans container A4 Pre qround coffee funnel AS Compartment for measure A6 Cup warmer shelf A7 Water tank A8 Infuser A9 Coffee grounds container A10 Cup tray A11 Compartment for latte macchiato milk glass A12 Drip tray A13 Service door A14 Coffee guide A15 Coffee spout adjustable height A16 Hot water and steam nozzle A17 Power cable A18 Main switch A19 ON STAND BY button A20 Hot water spout A21 Measure A22 Control panel graphic touch screen Description of milk container page 3 B B1 Frothed milk regulator B2 Milk container handle B3 CLEAN button B4 Milk intake tube B5 Milk spout B6 Lid with milk frother Description of control panel graphic touch screen page 3 LC g NB Only the icons relating to the controls enabled for the particular function currently being used will be lit on the touch screen C1 Display guides the user in using the appliance C2 s icon to deliver a cup of espresso coffee C3 icon to deliver
31. s dis played 4 Press the icon to select This deactivates the function and the symbol disappears from the display 5 Press the P icon to exit the menu g NB To activate this function the time must have been set previously AP Setting auto off g NB The appliance is set to switch automa tically to stand by if not used for 30 minutes The time can be changed so that the appliance swit ches off after 1 or 2 hours 1 Choose the CLOCK section as described above Press the selection icons lt or gt icons until AUTO OFF is displayed Press the icon to confirm Press the selection icons lt or gt until the required number of operation hours 30 minutes 1 or 2 hours is displayed Press the icon to confirm or the P icon to cancel the operation The appliance is automatically ready for use again and auto off is reprogrammed MAKING COFFEE Selecting the coffee taste The appliance is set by default to make coffee with a standard taste To change the taste press the selection icon C4 until the taste bar has filled as follows Extra mild taste Mild taste Standard taste Strong taste CHD xtra strong taste po q ga m The bar fills up progressively each time you press the selection icon C4 Selecting the quantity of coffee in the cup The appliance is set by default to make a standard quantity of coffee To choose the quantity of cof fee press the sel
32. s preparation progresses Once the coffee has been made the appliance pre pares for use again g NB While the machine is making coffee delivery can be interrupted at any moment by pressing the lit cup icon Atthe end of delivery to increase the quantity of coffee in the cup just press within 3 seconds one of the coffee icons sor Zi Once the coffee has been made the appliance is ready to use again g NB Tips For hotter coffee you should 1 perform a rinse cycle as described in the sec tion Manual rinsing 2 before making coffee warm the cups by rin sing them with hot water using the hot water function A Important If the coffee is delivered a drop at a time too fast and not creamy enough or too cold read the tips in the Troubleshooting section on page 24 Making coffee using pre ground coffee A Important Never add pre ground coffee when the coffee maker is turned off or it could spread through the inside of the appliance and dirty it This could damage the appliance Never use more than 1 level measure or it could dirty the inside of the coffee maker or block the funnel g NB If you are using pre ground coffee we recommend you make just one cup of coffee at a time 1 Repeatedly press the selection icon C4 cor responding to the taste bar until Ground taste and are displayed on the display 2 Put one level measure of pre ground coffee into the funnel fig 1
33. scaler diluted with water according to the proportions indicated on the descaler pack Always use descaler recommended by De Longhi contact De Longhi Customer Services Place an empty container with a minimum capacity of 1 5 litres under the hot water spout B7 fig 4 Important Danger of burns Hot water containing acids flows out of the hot water spout VER with splashes of water Hess the selection icon corresponding to OK to start the descaling programme 8 The message DESCALING UNDERWAY is displayed The descaling programme starts and the descaler liquid comes out of the water spout The descale programme automatically performs a series of rinses and pauses to remove limescale deposits from inside the machine After about 30 minutes the message RINSING FILL TANK is displayed 9 The appliance is now ready for rinsing through with clean water Remove the water tank empty rinse under running water fill with clean water and replace RINSING Press OK is displayed Empty the container used to collect the desca ler solution and replace it under the hot water spout Press the selection icon corresponding to OK Hot water flows out of the spout and the mes sage RINSING is displayed When the water tank is empty RINSING COM PLETE Press OK is displayed Press the selection icon corresponding to OK fill the water tank put it back in place and the appliance is ready for use SETTING WAT
34. two cups of espresso coffee C4 Selection icons to choose the coffee taste When in the settings MENU they change function according to the text shown above the icon C5 HOT MILK icon to deliver a cup of milk C6 FLAT WHITE icon to deliver a cup of macchiato C7 icon to perform a manual rinse When in the settings MENU it changes function according to the text shown above the icon C8 LATTE icon to deliver a cappuccino C9 CAPPUCCINO icon to deliver a caffelatte C10 Selection icons to choose the coffee quantity When in the settings MENU they change function according to the text shown above the icon cm icon to activate the hot water fugtion C12 P icon to access or exit the programming menu g NB A light touch is enough to activate the icons Meaning of animations Below is an explanation of the animations descri bing the operation the appliance is currently per forming Rinsing Heating up IMPORTANT MESSAGE see section Displayed messa ges Please wait FILL TANK Hot water el ES eS BEFORE USE Controls after transport After removing the packaging make sure the pro duct is complete and undamaged and that all accessories are present Do not use the appliance if it is visibly damaged Contact De Longhi Customer Services Installing the appliance Important When you install the appliance you should follow the safety warnings below
35. y be turned when the coffee mill is in opera tion For slower coffee deli oo 1 very and a creamier cof fee turn one click PS k 3 towards 1 finer lt ground coffee gt For faster delivery not a 00 Zo drop at a time turn one click towards the 7 coarser ground coffee These adjustments will only be evident after making at least 2 cups of coffee If delivery is still too fast or too slow repeat the correction proce dure Manual rinsing For hotter coffee before making the coffee rinse the appliance by pressing the button Hot water flows out of the spout heating the internal circuit and making the coffee delivered hotter A Danger of burns During rinsing a little hot water comes out of the coffee spouts and is col lected in the drip tray underneath Making coffee using coffee beans A Important Do not use caramelised or can died coffee beans as they could stick to the coffee mill and make it unusable 1 Fill the container A3 with coffee beans fig 9 2 Place under the coffee spouts 1 cup if you want 1 coffee fig 10 2 cups if you want 2 coffees 3 Lower the spouts as near as possible to the cup This makes a creamier coffee fig 11 4 Press the icon corresponding to the number of coffees required 1 cup 2 or 2 cups Bo fig 12 and 13 The selected quantity and taste are displayed 5 Preparation begins One or two cups appear on the display and gradually fill a
Download Pdf Manuals
Related Search