TP-LINK 24-Port Gigabit Desktop/Rackmount Switch
Contents
1. gt One TL SG1024D 24 Port Gigabit Desktop Rackmount Switch gt One power cord gt This User Guide gt Mounting screws and two L planks Make sure that the package contains the above items If any of the listed items are damaged or missing please contact with your distributor Chapter 1 Product Introduction This chapter describes the features of the TL SG1024D 24 Port Gigabit Desktop Rackmount Switch 1 1 Product Overview The TL SG1024D 24 Port Gigabit Desktop Rackmount Switch provides you with a high performance low cost easy to use seamless and standard upgrade to boost your old network to 1000Mbps Increase the speed of your network server and backbone connections make Gigabit a reality Power users in the home office workgroup or creative production environment can now move large bandwidth intensive files faster Transfer graphics CGI CAD or multimedia files and other applications that have to move large files across the network almost instantly The TP LINK TL SG1024D features a non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput MAC address auto learning and auto aging IEEE802 3x flow control for full duplex mode and backpressure for half duplex mode It is compatible with all 10 100 and 1000Mbps Ethernet devices because it is standard based It protects your existing network investments while providing you with a straightforward migration path to f2. 4 Supply power to the Switch with the provided power cord 3 3 Connect to Ground Connecting the Switch to ground is to quickly release the lightning over voltage and over current of the Switch which is also a necessary measure to protect the body from electric shock In different environments the Switch may be grounded differently The following will instruct you to connect the Switch to the ground in two ways connecting to the Grounding Bar or connecting to the Ground via the power cord Please connect the Switch to ground in the optimum way according to your specific operation environment e Connecting to the Grounding Bar If the Switch is installed in the Equipment Room where a Grounding Bar is available you are recommended to connect the Switch to the Grounding Bar as shown in the following figure Switch Rear Panel 2 Grounding Terminal Ground Cable Grounding Bar Figure 3 4 e Connecting to the Ground via the power supply If the Switch is installed in the normal environment the Switch can be grounded via the PE Protecting Earth cable of the AC power supply as shown in the following figure Switch Rear Panel 2 AC Power Cord with PE cable Figure 3 5 The figure is to illustrate the application and principle The power plug you get from the package and the socket in your situation will comply with the regulation in your country so they may differ from the figure above If you intend t
3. cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning CE This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures CONTENTS Package Contents iii ia Chapter 1 Product Introduction cc eeecessececeseeeeteeseeeeeseseseseseneeneieeseeeesesereeaeeeneereneeeees 1 1 PrOdUCtOVEIViO Wisin ti diras 1 2 Feature ii iba Chapter 2 Identifying External COMpONENtS occccicicicnicnicniniconnconnnoncnnnnnnnaron or nr cn cnninnns 2 1 FrontPaelintuatonion ordre 2 2 Rear Panel ui Aid AENA 3 1 Precautions Aia 3 2 Installation A Ada 3 21 Desktop Installati n ssns a 3 2 2 Rack Installation eeececeeeeesceseeeeneeeeeeeeseeeseseaeaeeesereeeeeeseeaeeenreteneeeeees 3 3 Connect to Ground isanne ian i edie eed ee 3 4 POWER ON ia dae eG ek ec ee ea Appendix A Specifications momia odiado ne Appendix B Troubleshooting cecececeseseseteeetsereeeseseeeseaeeneeeeseseeeeseneeacieeeereneeeeeenasaeaes Appendix C Contact Information 0 cecceceseseseseesereresseeseeneneeeeeesereeseeeeacaeeeeteereeteneeaeees Package Contents The following contents should be found in your package
4. TP LINK User Guide TL SG1024D 24 Port Gigabit Desktop Rackmount Switch Rev 1 0 0 7106503213 COPYRIGHT 8 TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright O 2010 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT HE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not
5. aster Gigabit speeds The TL SG1024D is plug and play and no configuration is required Auto MDI MDI X cable detection on all ports eliminate the need for crossover cable or Uplink port Each port can be used as general ports or Uplink ports and any port can be simply plugged into a server a hub a router or a switch using the straight cable or crossover cable Diagnostic LEDs which display link status and activity allowing you to quickly detect and correct problems on the network 1 2 Features gt Complies with IEEE802 3 IEEE802 3u IEEE802 3ab standards gt 24 10 100 1000Mbps Auto Sense RJ45 ports supporting Auto MDI MDIX gt All ports Support Full Half Duplex transfer mode for 10 100Mbps and Full Duplex transfer mode for 1000Mbps gt Supports IEEE802 3x flow control for full duplex mode and backpressure for half duplex transfer mode Non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput v Supports MAC address auto learning and auto aging LED indicators for monitoring power link speed and activity Desktop and rack mountable steel case Internal power supply vyv v Chapter 2 Identifying External Components This Chapter describes the front panel rear panel and LED indicators of the Switch 2 1 Front Panel The front panel of TL SG1024D consists of switch model switch LED indicators and 24 10 100 1000Mbps RJ 45 ports Figur
6. d Rate Environmental and Physical Power Supply Output Operating Temperature Storage Temperature Operating Humidity Storage Humidity 100 240V 50 60Hz 0 6A 0 40 C 32 104 F 40 70 C 40 158 F 10 90 non condensing 5 90 non condensing 10 Appendix B Troubleshooting gt gt The Power LED is not lit Make sure the AC power cord connected the Switch with power source properly Make sure the power source is ON The Link Act LED is not lit when a device is connected to the corresponding port Make sure that the cable connectors are firmly plugged into the Switch and the device Make sure the connected device is turned on and working well The cable must be less than 100 meters long 328 feet Appendix C Contact Information For help with the installation or operation of the TP LINK TL SG1024D 24 Port Gigabit Desktop Rackmount Switch please contact us E mail support tp link com Website http www tp link com 11 TP LINK TP LINK TECHNOLOGIES CO LTD http www tp link com
7. e 2 1 TL SG1024D Switch Front Panel sketch The LED indicators include Power Link Act LED indicators which are used for monitoring and pre troubleshooting of the Switch The following section shows the LED indicators of the Switch along with an explanation of each indicator gt Power LED This indicator will light solid red when the Switch powers up If the LED is not lit please check the power supply and connection gt LINK ACT LED The LED indicates Link Active status The corresponding LED indicator will light solid green when connected to a network device It flashes green when data is being transmitted or received on the working connection gt 1000Mbps LED The corresponding port LED indicator will light solid green when it s working on 1000Mbps speed Not lit indicates working on 10 100Mbps speed 2 2 Rear Panel The rear panel of TL SG1024D features a power socket and a Grounding Terminal marked with Figure 2 2 TL SG1024D Switch Rear Panel sketch gt Grounding Terminal TL SG1024D already comes with Lightning Protection Mechanism You can also ground the Switch through the PE Protecting Earth cable of AC cord or with Ground Cable For detail information please refer to section 3 3 Connect to Ground gt AC Power Socket Connect the female connector of the power cord here and the male connector to the AC power outlet Please make sure the voltage of the power supply meets the requirement of the input vol
8. nd humidity operating environment 3 2 Installation This Switch can be either installed on the standard 465mm mountable rack or located on the desktop A Caution Please unplug the power cord before installing or removing the Switch 3 2 1 Desktop Installation To install the Switch on the desktop please follow the steps 1 Set the Switch on a flat surface strong enough to support the entire weight of the Switch with all fittings 2 Remove the adhesive backing papers from the rubber feet 3 Turnover the Switch and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the Switch Figure 3 1 Attaching Rubber Feet 4 Upturn the Switch and connect it to the network devices while keep enough ventilation space around 5 Connect the Switch to power source with the provided power cord 3 2 2 Rack Installation To install the Switch in an ElA standard sized 465mm rack follow the instructions described below 1 Secure the supplied rack mounting brackets to each side of the Switch with supplied screws as illustrated in the following figure Figure 3 2 Attaching Brackets 2 After the brackets are attached to the Switch use suitable screws not provided to secure the brackets to the rack as illustrated in the following figure BODODODON OOODODODDOO SOI ooooo0o0o0000000000000 Figure 3 3 Mounting Switch 3 Connect the Switch to network devices
9. o connect the Switch to the ground via the PE Protecting Earth cable of AC power cord please make sure the PE Protecting Earth cable in the 3 4 Power on The TL SG1024D 24 Port Gigabit Desktop Rackmount Switch is powered by an AC Power Supply Connect the Switch and power outlet by power cord Powering on the Switch it will be automatically initialized and the LED indicators should respond as follows 1 All of the LED indicators will flash momentarily for one second which represents a resetting of the system 2 The Power LED indicator will light up Appendix A Specifications IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T Protocol CSMA CD Ethernet 10Mbps Half Duplex 20Mbps Full Duplex Data Transfer Fast Ethernet 100Mbps Half Duplex 200Mbps Full Rate Duplex Gigabit Ethernet 2000Mbps Full Duplex 10Base T UTP category 3 4 5 cable maximum 100m EIA TIA 568 100 STP maximum 100m Standards 100Base TX UTP category 5 5e cable maximum Network Media 100m Cable EIA TIA 568 100 STP maximum 100m 1000Base T UTP category 5 5e cable maximum 100m EIA TIA 568 100 STP maximum 100m Number of Ports 24 10 100 1000Mbps Auto Negotiation RJ 45 ports LED indicators Power Link Act 1000Mbps Transfer Method Store and Forward MAC Address Automatically learning automatically agin Learning i y dl 1000Base T 1488095pps Port Frame Forwar
10. tage 100 240V 50 60Hz 0 64 Chapter 3 Installation 3 1 Precautions To ensure a long term and stable performance of the Switch please pay attention to the following before the installation 1 Safety Requirements Before cleaning the Switch cut off the power supply Do not clean it by the waterish cloth and never use any other liquid cleaning method Take waterproof measures during storage transportation and operation of the equipment Use only the power cord provided with the Switch Make sure the voltage of the power supply meets the requirement of the input voltage of the Switch Do not push any objects into the openings of the Switch Ensure the vent hole is well ventilated and unblocked Do not open or remove the cover of the Switch 2 Location Requirements When you choose a location for the Switch please follow these guidelines Install the Switch on a flat and stable surface that can support the entire weight of the Switch with all fittings Locate the Switch far from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight To ensure adequate air flow around the Switch At least 10 cm 4 inches of space at the front and rear of the Switch is needed for ventilation Make sure that the Switch will be accessible and that the cables can be easily connected Position the Switch away from water and moisture sources be sure to provide an acceptable temperature a
Download Pdf Manuals
Related Search