Fagor LF73DWiTU
Contents
1. 59 Stir with a spoon Close the lid tight and clean the salt around the container When the salt container needs filling you should always do it before a wash and not afterwards When do need to add salt A pilot light will come on to show when more salt needs to be added A Important If your dishwasher does not have a display or pilot light you should periodically refill the salt that has been used about every 20 washes for medium hard water The rinse aid helps drying and prevents drops of water from clinging to utensils after washing The rinse aid container is located on the inside of the door next to the detergent container It has a 4 position dispenser for adjusting the amount of rinse aid to the water quality the dispenser is set at position 2 at the factory If you notice drops of water on utensils increase the position of the rinse aid dispenser If the utensils have white or sticky lines lower the position When do need to add rinse aid The dishwasher itself will inform you of when the rinse aid needs refilling A pilot light on the design panel will come on when a refill is necessary IMPORTANT You should not use salt if your dishwasher does not need it In this case the pilot light will remain PILOT LIGHT on at all times RINSE AID CONTAINER ED Once the level of the dispenser has been set fill the container to the top but do not overfill it If th2. hardness Check the result of the test against the table below You will probably need to adjust your dishwasher e Y A Scale level HF 0 13 HF 14 38 HF 39 50 HF 51 63 HF Over 63 HF Scale level DH 0 7DH 8 21 DH 22 28 DH 29 35 DH Over 35 DH Test result HEHH EN EN El Green 1 Red stripe 2 Red stripes 3 Red stripes 4 Red stripes Dial No salt needed Position 1 Position 2 Position 3 Position 4 position Electronic LO L1 L2 L3 L4 Soft Standard Medium Hard Very hard HF Water hardness French system DH Water hardness German system If no salt needs to be added to your dishwasher go straight on to the rinse aid section 51 Controlling the salt level Depending on the model dishwashers will have a manual or electronic salt level control This simple adjustment of your dishwasher is vital for its correct functioning Do not ignore it MANUAL REGULATION If there is a salt regulator like the P one shown in the photographs Mod A B inside your dishwasher e e on the right hand side turn it to the a number that corresponds to the e x hardness of the water in your area see table To turn it to the correct position use REGULATOR Model A REGULATOR Model B a coin Mod A or a screwdriver Mod B If you wish to use combined detergent tablets 3 in 1 4 in 1 turn the dial to the corresponding test result number If you use traditional detergents after this t
3. beeps and the malfunction can be cancelled by pressing the on off button 71 Why wont the dishwasher start This may be because There is no power It isn t plugged in correctly The power fuses have blown The dishwasher is not connected to the mains You haven t pressed the On Off button the pilot light for this button must be on continuously The dishwasher door is not closed correctly You have not pressed the Start button The dishwasher starts up but no water comes into the appliance This may be because There is no water supply The stop tap is off The water inlet electrovalve filter is blocked The water does not drain off and stays in the dishwasher This may be because The drain is blocked or badly fitted The drainage pipe is blocked or kinked The filters are blocked The selected programme has not ended Wait until it finishes The low salt level pilot light does not go off This may be because A low salt level Add salt and stir with a spoon The water hardness is below 7DH which means that salt is not necessary In this case the light will always be on Traces of detergent are left in the dispenser or on the door This may be because One of the utensils is preventing the dispenser from opening The detergent is past its expiry date or is not appropriate The sprinklers are hitting the dishes when they turn The sprin
4. items EN 50242 such as saucepans IM IN Y Ly WH as SA Vo bs i Na H WI D mm 1 HH WI VERTICAL POSITION HORIZONTAL POSITION IMPORTANT Bowls are placed on the left and plates on the right Start loading plates from the outside of the rack to the inside Plates should not be touching Les couverts Except for knives cutlery should be placed in the cutlery rack with the handles at the bottom Place the more delicate items such as cups glasses porcelain or crystal and standard size plates in the top rack Long cutlery has a special place There are also racks which when vertical are for holding wine glasses If you have selected the Express programme or the Top Load function the dishes are to be loaded into the top basket only If you have selected the Bottom Load function you should load the lower basket only IMPORTANT When you have loaded the dishwasher make sure the sprinklers can spin freely and that the cutlery will not prevent the detergent tank cap from opening EN 50242 English TOP LOAD 63 Adjusting the racks The racks can be adjusted in accord with the load The top rack can be placed at two different heights for washing different sized plates In the upper position the top rack holds standard size plates of up to 19 cm and the bottom rack holds plates of up to 31 cm In the lower position the
5. top rack holds plates of up to 24 cm and the bottom rack holds plates of up to 26 cm Top rack model A This can be adjusted without being removed from its rails even when loaded with utensils To raise or lower its position pull the rack upwards by the side handles Check that both sides are at the same height If not make them level Top rack model B Remove the stop that prevents the rack wheels from coming out of the rails Pull the rack towards you and take it out Position the basket at the height required Replace the stop in its original position making sure it fits right in longitudinally on the rail you will hear a click when it locks in place English 3 SELECTING THE WASH PROGRAMME TOP or BOTTONI LOAD SALT selector TIME DELAY SE PROGRAMME PROGRAMME ENO pilot light RINSE AID selector Visor selector button pilot light VISOR TOP or BOTTOM LOAD pilot lights PROG STOP ME iy PROGRAMME pilot llight selector 9 END OF PROGRAMME DELAYED PROGRAMMING pilot light pilot lights PROG STOP HALF LOAD selector HALF LOAD pilot light The steps for selecting the wash programme are as follows Open the dishwasher door Press the D dishwasher ON button Select the wash programme using the PROG button On models without a display a pilot light will come on to indicate which programme has been selected and on displ
6. Manual de instalaci n y uso del aparato Manual de instala o e utiliza o do aparelho Installation manual and instructions for use Installations und Bedienungsanleitung NDICE NDICE TABLE OF CONTENT INHALT ESPANOL INSTALACI N Y MONTAJE 3 USO DEL APARATO Y CONSEJOS PR CTICOS 9 MANTENIMIENTO Y LIMPIEZA DEL APARATO 21 LOCALIZACI N y SOLUCI N DE PROBLEMAS 23 ESQUEMAS Y MEDIDAS DE INSTALACI N 99 PORTUGU S INSTALA O E MONTAGEM 27 UTILIZA O DO APARELHO E CONSELHOS PR TICOS 33 MANUTEN O E LIMPEZA DO APARELHO 45 LOCALIZA O E SOLU O DE PROBLEMAS Ar ESQUEMAS E DIMENS ES DE INSTALA O 99 ENGLISH INSTALLATION AND FITTING 51 USING THE APPLIANCE A FEW PRACTICAL TIPS 57 APPLIANCE MAINTENANCE AND CLEANING 69 TROUBLESHOOTING xi INSTALLATION MEASUREMENTS AND DIAGRAMAN 99 DEUTSCH INSTALLATION UND MONTAGE 75 BENUTZUNG DES GER TS UND PRAKTISCHE RATSCHL GE 81 INSTANDHALTUNG UND REINIGUNG DES GER TS 93 FEHLERSUCHE UND PROBLEML SUNG 95 PL NE UND MABNAHMEN ZUR INSTALLATION o3 DISHWASHER INSTALLATION AND FITTING UNPACKAGING 4 pues nll 1 UNPACKAGING THE DISHWASHER Remove the internal pro tection polystyrene wed ges for holding the racks firm Ne E OM a 2 CONNECTION TO THE PLUMBING The water connection pipe is located on the back of the dishwasher ED Connect the pipe to the water inlet tighten the connection nut and make sure it is securely c
7. ay models the selected programme number will appear on the display preceded by the letter P y d mm WITHOUT DISPLAY WITH DISPLAY 65 There are various programme types depending on the dishwasher model It is very important to choose the wash programme in accordance with the type and amount of utensils and level of soiling TOTAL TEMPERATURE NUT PROGRAMME SYMBOL TYPE OF UTENSILS DETERGENT CONSUMPTION 99900 Prewash A Cold For utensils not to be Withou 0 007 KWh P1 washed immediately detergent For very dirt ii B 70 a 25 15 1 4 KWh 2 Vo saucepans NY Normal 65 O For dirty utensils 25 5 1 2KWh Auto 99 09 P3 Economic e 50 Solr telah ely 2545 1 05 KWh P4 utensils Quick 2 gt 55 For very slightly 25 0 79 KWh P5 we dirty utensils Mixed Mix 50 For dirty delicate 2545 0 87 KWh P6 utensils see WJ For very slightly dirty ia w 40 utensils in the top rack 20 0 3 KWh only Hygienizer Hyg 75 For more efficient 2545 1 6 KWh P8 Le bacteria elimination 25 g of powder non concentrated detergent is the equivalent of one and a half flat soup spoons or one tablet of detergent For tablet or liquid detergent follow the detergent manufacturer s recommendations Values for a 60W motor and 12 place settings In compliance with the EN 50242 standard the economy wash programme takes longer than the other programmes however it consumes less energy and is more environment friendly A 3 send continu
8. ce before disposing of it means you will prevent possible negative consequences for the environment and health which may be given rise to by incorrect disposal and it means the materials making it up can be treated and recycled obtaining important savings on energy and resources To remind you that you must collaborate with a selective collection scheme there is a symbol on the product warning you not to dispose of it in traditional refuse containers EEE For further information contact your local authority or the shop where you bought the product Esquemas y medidas de instalaci n Esquemas e dimens es de instala o Installation measurements and diagrams Plane und MaBnahmen zur Installation 99 02 08 V28F013W3
9. e additional functions all the functions selected number of hours you wish are cancelled to delay the start of the wash 5 START UP When you have selected the wash programme and the additional functions close the dishwasher door and it will start up automatically When the dishwasher is 1 Open the dishwasher door Unless the change affects in operation and 2 Put the utensil in the the duration of the wash You wish to put another dishwasher and or change programme or involves the utensil in the dishwasher the wash programme time delay option In this You wish to change the 3 Close the dishwasher door case press the ON OFF wash programme button O to make any NOTE For safety reasons changes the programme will restart after a few seconds 67 6 END OF PROGRAMME When the dishwasher programme ends a continuous beep will sound for 3 seconds When you open the dishwasher door you will O O be able to see that washing has finished as a pilot light will have lit up MODELS on the design panel DISPLAY The dishwaser must always be switched off by pressing the OFF button a POWER CUTS After a power cut the minimum memory of 12 dishwasher continues to hours depending on work as normal from model type where it stopped it has a 8 BASIC TIPS There a few things you should always bear in mind If you do your dishwasher will last longer and be more efficient Fill th
10. e dishwasher Try to make the most of your dishwasher s capacity This will help you reduce water and electricity consumption and lead to quieter operation and be more economical Place the dishes correctly For optimum wash quality the sprinklers must turn freely The dishes must also be correctly placed so that the jet of water reaches them Programme selection Select the correct wash programme and additional functions as required DISHWASHER APPLIANCE MAINTENANCE AND CLEANING You should perform the Clean the filter cleaning operations Cleaning the spray arms regularly so that your Clean the inside If you are planning dishwasher will last Clean the outside to be away for a long longer This will make your period leave the You should do the dishwasher last dishwasher door following every three longer SPSI SO that the air months can circulate freely inside the machine 1 CLEANING THE WASH FILTER The filter is made up of two or three parts depending on model type interior filter exterior filter and filter protector It is located at the bottom of the dishwasher under the bottom rack EP Take out the bottom rack remove the interior filter by turning it anticlockwise and pulling it upwards Remove the exterior filter Remove the filter 3 protector some models It is essential that filters CS are put back in place correctly Make sure the filter protector is in place The exterior f
11. ess level You have used a phosphate free detergent Try with detergent containing phosphate The utensils do not come out dry This may be because There is no rinse aid The rinse aid control is not set correctly The utensils are positioned incorrectly The utensils have been taken out too soon The wash programme is inappropriate Glass or crystal comes out with a milky appearance or scratched This may be because They are not dishwasher compatible The detergent is inappropriate Glass or crystal comes out looking opaque There is not enough rinse aid The glasses and cutlery have a dull appearance and the glasses have a metallic shine Too much rinse aid Utensils made of stainless or fine steel come out stained This may be because They are not dishwasher compatible The utensils are positioned incorrectly You have used too much detergent The steel is low quality There is too much salt in the wash water Close the salt container lid correctly 13 DISHWASHER FURTHER INFORMATION INFORMATION FOR THE CORRECT DISPOSAL OF ELECTRICAL AND ELECTRONIC APPLIANCES When the appliance reaches the end of its service life you should not dispose ot it with the general domestic waste It can be taken free of charge to the local administrations specific selective collection centres or to distributors who provide this service Separating a domestic applian
12. ilter fits into position Put the interior filter in position and turn it clockwise as far as it will go 69 2 CLEANING THE SPRINKLERS The third sprinkler depending on the model the top sprinkler and the bottom sprinkler should be cleaned every three months To remove the sprinklers for cleaning The third sprinkler is removed by pressing upwards on it and then unscrewing it us NG The top sprinkler is fitted to the top basket It should be totally unscrewed to remove it 4 W z th de q 3 IE z The bottom sprinkler is removed by turning the lower screw to the left to loosen it and then pulling upwards on the sprinkler Rinse the sprinklers under the tap and clean them with a non scratch sponge The water outlet holes must be kept clean Unblock any holes that are obstructed Then put the sprinklers back IMPORTANT Before any cleaning or maintenance operations unplug the dishwasher from the mains 3 CLEANING THE INSIDE OF THE APPLIANCE The dishwasher should Instead of detergent use be cleaned every three appliance cleaner follow months to remove the dirt the manufacturer s lodged in the appliance instructions 4 CLEANING THE OUTSIDE OF THE APPLIANCE Clean the outside with a cloth and soapy water Use non scratch and non abrasive products Dry with a cloth IMPORTANT For safety reasons make sure the appliance is not in ope
13. instructions Position the template fix it in place and mark the position of the holes Drill the holes with a fl 2 5 mm bit and screw the supports to the panel with the curved part facing downwards Pick up the door panel and fit the Supports into the door housing Pull it downwards ensuring it is firmly fixed and levelled with the top part of the door Open the dishwasher door slowly holding the panel in place and then fix it with the screws ensuring the panel is correctly aligned with the door If the door springs are not strong enough compensate the door with the two additional screws provided in the accessories bag Fit the dishwasher into the space Adjust it to the worktop until the top of the dishwasher makes contact with the bottom of the kitchen fitting Fit the plinth in place sawing it to obtain the desired measurement Fix the dishwasher to the worktop in the case of a wooden worktop If it is a granite worktop fix the dishwasher to the adjoining fittings IMPORTANT The maximum and minimum recommended weighis for the door panel to be placed on the dishwasher are Maximum 6 5 kg Minimum 3 kg IMPORTANT A space of at least two millimetres must be left at the sides between the kitchen fittings or electrical appliances and the dishwasher English For integrated stainless steel models the following installation instructions should be taken into account Colu
14. is occurs clean the spillage with a cloth IMPORTANT Agreater amount of rinse aid does not necessarily mean better results In fact too much rinse aid can lead to water marks PILOT LIGHT English Detergent The detergent is poured into a tank on the inside of the door beside the rinse aid tank Pour in the detergent then close the tank cap Some programmes also require part of the dose of detergent to be poured into the tank cap compartment Detergent comes in tablet powder and liquid form You can consult the amount of detergent needed on the programme chart If you use detergent tablets instead of traditional products granulated salt powder detergent liquid rinse aid you may notice a loss of efficiency particularly in the case of short programmes and or programmes with low wash temperatures If you notice any performance problems with your dishwasher e g there is a white film on the tank or on the dishes an accumulation of scale or poor drying efficiency you should go back to using traditional products We would remind you that if you go back to using traditional granulated salt you will need to run a few programmes before the dishwasher performs perfectly again and there may still be some residue left on the tank and dishes If you wish to use combined tablet products read the instructions and indications for use on the packet carefully In case of doubt consult the cleaning
15. kler holes are blocked The detergent container was damp when the detergent was added The container must be dry Unusual foam appears You have used detergent for washing dishes by hand instead of special detergent for dishwashers The dishwashers uses a lot of salt This may be because The lid to the salt container is not closed correctly The salt consumption level is not at the correct setting The dishwasher makes strange noises This may be because The dishwasher was not installed correctly The sprinklers are hitting the dishes when they turn English 2 PROBLEMS WITH THE QUALITY OF THE WASH Remains of dirt or food on the utensils This may be because The wash filter is dirty blocked or not correctly in place The sprinkler holes are dirty or the sprinklers are being blocked by the dishes The detergent is inappropriate or there is an insufficient amount The utensils are not positioned correctly Some utensils are in contact with others There are too many utensils in the racks The wash programme is inappropriate The drain is blocked The food remains on the utensils were too old and dry The utensils come out white This may be because There was not enough detergent or rinse aid The salt container lid is not closed correctly The salt container has no water or salt The water softener is not correctly adjusted to the water hardn
16. mn integrated Integrated beneath a worktop oa 50 114 mmj lt 55 5 PRE WASH Once the dishwasher has been installed correctly it should be first used on prewash programme Open the dishwasher door Press the dishwasher D ON button Select programme 1 prewash with no dishes or detergent Close the door The dishwasher will start up automatically This is to check the installation the connections and the drain outlet as well as to completely wash the interior before running a wash pro gramme DISHWASHER USING THE APPLIANCE A FEW PRACTICAL TIPS 1 WATER HARDNESS SALT RINSE AID AND DETERGENT Water hardness adjustment VVater contains scale The more scale the harder the water To prevent the scale in the water from damaging the dishwasher it is equipped with a descaler to reduce the scale and leave it perfectly clean for washing The descaler uses salt to function Before starting up the dishwasher you will need to know the water hardness in your area You can find this out by either 1 H Consulting the local Water Board 2 H consulting the T A S Technical Assistance Service or 3 H using the Aquadur strip included in the accessories bag following the instructions below To find out the water hardness ED Place the strip in a glass of water _ for one second and then take it 7 out LD Shake it and wait for one minute DP The strip will show the water
17. onnected to the appliance The hose must run between the wall and the bottom space at the back of the dishwasher b1 so that it is not squashed or overstretched There should be a fixed water outlet drain at a distance of between 25 and 100 cm from the floor Make sure that the outlet pipe is not too rigid bent or squashed IMPORTANT If your dishwasher has a hot water inlet connect the pipe to the hot water tap In this case the maximum temperature must not exceed 60 C Bear in mind that this type of water supply may affect the washing and drying capacity of the appliance It is very important for the bend pipe of the outlet hose is located securely in water outlet so that it cannot disconnet The operating water pressure minimum and maximum must be between 0 5 10 bar 0 05 1 MPa 3 ELECTRICAL CONNECTION Please refer to the specification label on the top edge of the door before making the electrical connections Make sure that the power voltage connected to the plug socket is as shown on the label It is very important for the dishwasher to be connected to an earthed plug socket The electrical installation plug socket fuses or circuit breaker and meter must be capable of the maximum power shown on the specifications label If the power cable is damaged it must be replaced exclusively by the manufacturers aftersales service TAS or authorised personnel If the appliance is
18. ous beep and a light indicate the end of the programme The Express programme requires powder or liquid detergent which dissolves easier English 4 SELECTING ADDITIONAL FUNCTIONS Wash functions must always be selected after the wash programme has been selected If the programme is changed during the selection the previously selected functions are cancelled These functions make it possible to adjust the wash load times and consumption to a maximum The additional functions available depend on the model fes gt Button Time delay Button Top bottom Button Half load This makes it possible to load Duo Zone This washes half a load delay the start of the wash Only half the dishwasher in the top rack only Valid programme Some models capacity is used Top for all programmes can delay the wash 3 6 or load in the top rack for 9 hours In this case when more delicate utensils you press the time delay and Bottom load in the button a pilot light comes bottom rack for on to indicate the chosen saucepans or very dirty option utensils Valid for all On other models it is programmes possible to select the time you wish to delay the wash from 1 to 19 hours at hourly intervals This is ideal for cheap rate periods On these models when you IMPORTANTE RTANTE press the time delay button If you change the programme or press the ON OFF button the display shows the while selecting th
19. product manufacturer We provide no guarantee for any complaints directly related to the use of this type of products E ore it Ea Bit 3 Ss haa El El i TT k 4 hd Pe tr A E Hall 4 s 61 2 TABLEWARE AND UTENSILS TYPES AND POSITIONING Types of dishes Not all utensils can be washed in a dishwasher Do not attempt to wash items made of wood or earthenware or plastic that is not heat resistant Stainless steel cutlery can be washed easily however ensure that silver cutlery does not come into contact as they may stain Items made of aluminium may fade in time Patterns on decorated porcelain may wear off if the quality is not good Check with the manufacturer of China Only wash glasses that are dishwasher compatible Cut glass should not be washed in dishwasher A Please make sure your utensils are dishwasher compatible Placing the utensils in the dishwasher It is very important to place the utensils correctly in the racks to guarantee a perfect wash The lower rack is for dirtier more resistant items pans oven dishes and plates Make sure there is sufficient space between each one for the jet of water Pots must be placed upside TE Wl down A O ar ny If your model has fold down racks you can use them in vertical Ye VU Te re SA i position for washing plates or in horizontal FOR 12 PLACE SETTINGS LOADING PLATES position for large
20. ration while it is being cleaned DISHWASHER If you find a problem when using your dishwasher you will probably be able to solve it by consulting the following section If this is not so please contact the TECHNICAL ASSISTANCE SERVICE and be ready to provide as much information as possible TROUBLESHOOTING a POR 1 TECHNICAL OR FUNCTIONAL PROBLEMS When the dishwasher detects a malfunction it will give you acoustic or visual warnings depending on the model On the top edge of the dishwasher door some models there is a table to identify possible oroblems LAB Models with a md display These models identify the fault with the letter F followed by a number from O to 10 DE Models without a display When there is a malfunction the dishwasher gives off a series of beeps which stop in seconds and then start up again You can identify the malfunction by counting the beeps 1 en door open 2 no water at inlet and so on The dishwasher will begin to beep If you wish to hear the beeps again to count them press the button and the beeps will sound again Depending on the type of malfunction contact the technical service about the problem MALFUNTION DISPLAY RE Close the door F1 1 Not entering F2 2 Not leaking F3 3 Flood Fd 4 Over heating F5 5 Not heating F6 6 Temp no detect F7 1 No pressure F8 8 Not even F9 9 Control FO 10 The series of
21. to be recessmounted and integrated the plug must be accessible after installation Model Serial number lu en i eo za A oa N 060300001 e r P hi hm AT p E oral Td TYPE TWHE Ej SAA ros AA A E MAA DDD6 012 0122640603000 IMPORTANT The specifications label is on the top edge of the interior of the door This label must never be removed since it provides information about the exact model of the dishwasher required power supply serial number and warranty English 4 LEVELLING AND POSITIONING To install an integrated dishwasher WORKTOP If the worktop is wooden fit the plastic protection onto it to prevent the area from being damaged by steam Fit the front brackets to the dishwasher so that it can be fixed to neighbouring units or the work surface see point k page 54 LEGS LEVELLING To flush mount the dishwasher in a row of kitchen fittings sharing the same plinth loosen and remove the base accessories Before fitting the dishwasher into the space raise it up to the height of the worktop by turning the rear legs until a space of some 3 mm is left from the top Then adjust the front legs to the desired height Some integrated models include a rod for levelling the rear legs from the front 53 DOOR An information template is provided with the assembly instructions An information template is provided with the assembly
22. urn the dial to the test result number again ELECTRONIC ADJUSTMENT If there is a salt regulator inside your dishwasher on the right e g Mod C or Mod D you should adjust the salt from the control panel with the dishwasher running pressing the on off button but with no programmes running Identify your dishwasher Type A or Type B Type A models display models Press the gt Type A display models button and hold it down He en Gn OD B S O S m PROG stop jo oo NEN WMM for 3 seconds A number with the letter L before it a Type B pilot light models L2 will appear on the display Press the button again to select the salt regulator position required Display models English Type B models pilot light models Press the LS button The L2 pilot light will come on see Table Press the ls button again to select the salt regulator position required Validate the required selection by pressing the PROG button GD Display models and pilot light models Remember You should adjust the salt position depending on the result of the water A hardness test See table on 57 page WHERE TO PUT THE SALT The dishwasher has a salt container in the bottom of the tub Important use dishwasher salt only do Es SALT CONTAINER The first time you fill the salt container you must Pour in the salt but do not fill the container to the top Top it up with water
Download Pdf Manuals
Related Search