Metra GMOS-LAN-03 car kit
Contents
1. Black Yellow wire on the 12 pin harness Push the blue Onstar button while the voice is speaking tap the Black Yellow wire to ground There are 4 volume settings for Onstar once the Ath setting is reached and the Black Yellow wire is tapped to ground it will automatically go back to the first vol ume setting Once the volume is set it will stay at that volume until the Black Yellow wire is tapped to ground again This can be set during installation and then left alone If user adjustment is desired a momentary contact switch sold separately can be added Connect one terminal from the switch to ground and the other terminal to the Programming Bluetooth function through steering wheel If anipe 1 Turn on ignition and radio 2 Press and hold the phone button on the steering wheel 3 After you hear the audible sound ready release the button 4 Enjoy your Bluetooth i 1 800 221 0932 LJ www axxessinterface com REV 11 22 10 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INSTGMOS LAN 03 72. ONS SO AS TO PROPERLY AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNI CIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE INTERFERENCE WEE SAFETY SYSTEMS COULD CAUSE HARM TO PERSONS IF YOU HAVE ANY QUESTIONS IN THIS REGARD PLEASE CALL THE METRA HELP LINE AT 1 800 221 0932 FOR ASSISTANCE KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow Bcc sr TOOLS REQUIRED FOR INSTALLATION e Cutting Tool Tape e Crimping Tool Connectors ie butt connectors bell caps etc SPDT Relay optional Female Spade Connectors Optional WIRING CONNECTIONS Important Before beginning any of the following disconnect the negative battery terminal to prevent accidental short circuit FOR INSTALLATION OF AFTERMARKET RADIO ONLY From the 14 pin harness Connect the red wire to the ignitionaccessory wire of the aftermarket radio Connect the Blue white wire to the amp turn on wire of the aftermarket radio Connect the white wire to the left front positive speaker output of the aftermarket radio Connect the white black wire to the l
3. e to the VSS or speed sense wire of the aftermarket navigation radio 3 Connect the Green Purple wire to the reverse wire of the aftermarket navigation radio When completed plug the 14 pin harness into the GMOS LAN 03 CONNECTIONS BE MADE ON THE PIN GM HARNESS 7 Connect the Orange wire to the illumination wire of the aftermarket radio If there Is no illumination wire just tape the Orange wire up 2 Connect Orange White wire to the dimmer wire of the aftermarket radio If there is no dimmer wire just tape the Orange White wire up Connect the green wire to the amplifier s left rear positive speaker output Connect the the green black wire to the amplifier s left rear negative speaker output Connect the purple wire to the amplifier s right rear positive speaker output Connect the purple black wire to the amplifier s right rear negative speaker output Cut the white wire about half way between the two plugs Connect the white wire from the 24 pin plug to amplifier s left front positive speaker output wire Connect the white wire from the 12 pin plug to the positive speaker wire of the Metra SP 2003 or equivalent 8 Connect the two pin harness to the two pin connector located on the 12 pin harness side of the GMOS LAN 03 MO s 4 8 Cutthe white black wire about half way between the two plugs Connect the white black wire from the 24 pin plug to amplifier s left front negative speaker output wire Connect t
4. eft front negative speaker outout of the aftermarket radio Connect the gray wire to the right front positive speaker output of the aftermarket radio Connect the gray black wire to the right front negative speaker output of the aftermarket radio Connect the brown wire to the mute wire of the aftermarket radio If the after market radio does not have Mute wire tape up the brown wire The following wires on the 14 pin harness are for the aftermarket radios that have navigation built in 1 Connect the green wire to the parking brake wire of the aftermarket navigation radio 2 Connect the blue pink wire to the VSS or speed sense wire of the aftermarket navigation radio 3 Connect the green purple wire to the reverse wire of the aftermarket navigation radio From the 12 pin harness 7 Connect theYellow wire to the 12 volt constant battery wire of the aftermarket radio 2 Connect the Black wire to the ground wire of the aftermarket radio 3 The Black Yellow and Black White wires will be discussed later in this manual From the 30 pin GM harness 1 Connect the Orange wire to the illumination wire of the aftermarket radio If there Is no illumination wire just tape the Orange wire up 2 Connect Orange White wire to the dimmer wire of the aftermarket radio If there is no dimmer wire just tape the Orange White wire up Connect the Green wire to the left rear positive speaker output of the aftermarket radio Connect the Green B
5. en the factory radio is removed the audible turn signal indicator is lost If that turn signal clicking is desired follow these steps 1 Using a SPDT relay Metra part E 123 connect pin 85 to the Black White wire in the 12 pin harness 2 Connect pin 86 to the 12 volt constant wire on the 12 pin harness 3 Be sure to cover the other leads of the relay by either using female spade connectors or using tape to cover the leads Now when the turn signal is on the relay will make the audible clicking noise INSTALLING THE GMOS LAN 03 1 With all connections completed plug the 14 and 12 pin harnesses into the GMOS LAN 03 2 Reconnect the negative battery terminal 3 Plug the 30 pin GM harness into the vehicle side harness and plug the aftermarket radio harness into the aftermarket radio 4 Cycle the key by turning the ignition on then back off then back on again to test the radio TESTING THE GMOQS LAN 03 1 the ignition on and then turn the aftermarket radio on 2 Push the Onstar button the radio should turn off and you should hear Onstar Push the Onstar cancel button and the radio should come back on CHIME VOLUME ADJUSTMENT To adjust the chime volume use a small screwdriver to rotate the potentiometer located on the 14 pin harness side of the interface clockwise to make the chime louder and counterclockwise to make the chime softer ONSTAR LEVEL ADJUSTMENT To adjust the Onstar volume level find the
6. he white black wire from the 12 pin plug to the negative speaker wire of the Metra SP 2003 or equivalent 9 Cut the gray wire about half way between the two plugs Connect the gray wire from the 24 pin plug to ampli fier s right front positive speaker output wire Connect the gray wire from the 12 pin plug to the positive speakerwire of the Metra SP 2003 or equivalent 10 Cut the gray black wire about half way between the two plugs Connect the gray black wire from the 24 pin plug to amplifier s right front negative speaker output wire Connect the gray black wire from the 12 pin plug to the negative speaker wire of the Metra SP 2003 or equivalent Note If only one SP 2003 is used tape up the gray wires that would normally connect to the second SP 2003 to avoid a short circuit CONNECTIONS TO BE MADE ON THE 12 BIN HARNESS 1 Connect the yellow wire to the radio s 12 volt battery or memory wire 2 Connect the black wire to the radio s ground wire 3 The black yellow and black white wire is for the Onstar volume adjustment This will be discussed in the Onstar and Chime Level Adjustment section of this instruction When completed plug the 12 pin harness into the GMOS LAN 03 FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connec SPLICE tions as shown below Strip Splice Solder Tape Isolate and individually tape
7. ipe GM ONSTAR LAN DATA BUS INTERFACE GMOS LAN 03 Installation Instructions Not compatible with amplified sound systems READ IMPORTANT WARNING ON PAGE 1 BEFORE ATTEMPTING ANY INSTALLATION The GMOS LAN 03 is designed to retain Onstar and retain the warn ing chimes that are normally lost when the OEM radio is removed It also provides a 12 volt accessory output for proper aftermarket radio operation THE GMOS LAN 03 also PROVIDES a MUTE PARK ING BRAKE VSS OR SPEED SENSE AND A REVERSE OUTPUT TO MAKE INSTALLING AN AFTERMARKET NAVIGATIONAL RADIO SIM PLER AND LESS TIME CONSUMING APPLICATIONS Chevrolet e Cobalt 2007 10 e HHR 2006 10 e Malibu 2008 11 Pontiac 5 2007 09 06 2009 10 e Solstice 2006 09 Saturn e Aura 2006 09 e Sky 2006 09 INTERFACE COMPONENTS e GMOS LAN 03 Interface e 14 pin harness with stripped leads e 12 pin to 30 pin GM harness X 1 800 221 0932 www axxessinterface com COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION Rev 11 22 10 i M READ IMPORTANT WARNING BEFORE ATTEMPTING ANY INSTALLATION IMPORTANT WARNING THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE CAREFULLY FOLLOWED THE INSTRUCTIONS ARE WORDED IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COM PLETING THESE TYPE OF ELECTRONIC INSTALLATIONS IF YOU ARE UNCLEAR AS TO WHAT YOU INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTI
8. lack wire to the left rear negative speaker output of the aftermarket radio Connect the Purple wire to the right rear positive speaker output of the after market radio Connect the Purple Black wire to the right rear negative output of the aftermarket radio Connect the two pin harness to the two pin connector located on the 12 pin harness side of the GMOS LAN 03 s d s See wiring diagram 1 on page 3 2 31IHAV3OV IS MOTTJAPIOV 18 0 IND S3MWlM 2 EG T WNVUu5VvIG S3LIHW3SNVHO JONVHO HH a1 91 o_o 0 NV T SONO a 0 SLIHM AN 18 AWNIOA AWIHD BC Re FOR AFTERMARKET RADIO AND AMPLIFIER See wiring diagram page CONNECTIONS TO BE MADE ON THE 14 PIN HARNESS Connect the red wire to the ignition accessory wire of the aftermarket radio Connect the blue white wire to the amp turn on wire of the aftermarket radio and to the blue white wire in the 24 pin harness White NOT USED White black NOT USED Gray NOT USED Gray black NOT USED Connect the Brown wire to the mute wire of the aftermarket radio If the after market radio does not have a Mute wire tape up the Brown wire The following wires on the 14 pin harness are for the aftermarket radios that have navigation built in 7 Connect the Green wire the parking brake Wire of the aftermarket navigation radio 2 Connect the Blue Pink wir
9. off ends of any unused wires to prevent electrical short circuit 5 SOLDER METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black GIOUND itv nen tentis Black Left Front White Power Antenna Blue Left Front White Black 0 Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black Salarialwv v3 I3 VINHLJV OL j CS H A mm 3owvuo SLIHM ASNVYO INAWLSNCAV AWNIOA AWIHD Nid 0 IND MOTISA MOV1E 0 NV TSONWO T dH 1 35 d1 1 Aldy LNO 4 A J NA OS d Odind N33H9 xNignig MEM REE m a I3 VINHIIJV OL 00c dS 00c dS TWNOILdO H 3ldlTdlNV OIQVSH L3MHVIASLJV Bo i ww AUDIBLE TURN SIGNAL Wh
Download Pdf Manuals
Related Search