Premier PBC-FCTA project mount
Contents
1. Avww mounts com Page 3 b 4 22 PP FCTA Features The suspended ceiling adapter makes it easy to install and fine tune the position of your overhead projector and organize its electrical wiring above the ceiling Mounting Coupler Use a set screw to hold any 1 1 2 NPT pipe to the mounting coupler Adjustability Up t Electrical Access Knockouts for electrical or signal junction boxes Camera Screw Hole Use a 1 4 20 screw to mount a camera alongside the projector Page 4 Visit the Premier Mounts website at http Avww mounts com Installation Instructions gt 4 PP FCTA PP FCTA Installation Introduction Read these instructions before installing your Premier Mounts product Make sure you have all the parts and tools you need to safely complete the installation Some of the steps in this installation may require two people to prevent personal injury and or damage to the projector Read all the warnings in the manual and always use proper safety equipment Mounting the PP FCTA Pre set four 4 M5 x 16mm combo screws on the ceiling plate assembly two on each end of the plate The M5 x 16 mm screws may be attached on the inner or outer lip of the main ceiling plate Determine the ceiling tile you will use to attach the ceiling adapter Use a pencil to measure and mark 3 from each edge of the t bar frames to the inside of the tile see diagram Determine the mounting hole position inside the marked2. OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the projector This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http Avww mounts com Installation Instructions gt 4 PP FCTA 24 Installation Tools The following tools may be required depending upon your particular installation They are not included Ladder Guy Hand Held Drill Protective Eyewear Phillips Tip Screwdriver Fai 4 1 8 Drill Bit 1 4 Concrete Drill Bit a er ole Saw Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 PP FCTA Mount Hardware Ya x 3 Eye Lag Screws Escutcheon Ring 14 Gauge x 25 Galvanized Wire 4 20 Turnbuckles M6 x 2 4 Concrete Anchors Qty 1 Qty 4 Strands Qty 4 Qty 4 Installation Instructions Visit the Premier Mounts website at http
3. square of the tile and mark it with a pencil If you are attaching a camera mark an additional hole for the 1 4 20 screw next to the mounting coupler Remove any of the 24 x 24 or 24 x 48 tiles that are surrounding the marked tile Cut the mounting hole and camera screw hole Place the ceiling plate on the t bar rails so that the mounting coupler can slide to align with the ceiling mounting hole Proceed to the Securing the Ceiling Plate section on page 6 1 4 20 optional holes e lt M5 x 16mm Screws Ceiling Plate Assembly Upper Adapter Plate T Bar Frame Ceiling Tile Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 5 Once the ceiling plate assembly is resting on the t bar frame rails use a screwdriver to tighten the four 4 M5 x 16mm combo screws Slide and center the upper plate assembly over the hole that was cut in the tile Tighten all four 4 wing nuts A Do not overtighten the mounting screws Proceed to the Electrical Box Cut out Removal section Electrical Box Cut out Removal Electrical installation should be completed by a certified electrician 1 Cut the tile where the electrical box is going to be secured 2 Using commercially available hardware depending on electrical installation environment install the electrical box and secure it to the ceiling plate assembly 3 Make all electrical connections a
4. angle 15 degrees outward from the main ceiling plate see Fig 2 Twist the wire at least five 5 times around itself to secure it Run the other end of the wire through the turnbuckle Twist the wire at least five 5 times around itself to secure it Repeat steps 1 4 for the remaining three mounting Figure 1 points The final loop on the wire has to be tightly bent and secured to prevent it from untwisting Twist the turnbuckles to fine tune adjust Recheck all hardware and installation for proper tightness and security Proceed to the Securing the 1 12 NPT Pipe to the PP FCTA Figure 2 section below Securing the 1 1 2 NPT Pipe to the PP FCTA Secure the 1 NPT pipe to the mounting coupler and tighten the pipe Secure the pipe using one 1 M5 x 16mm combo screw to the plate The M5 x 16mm combo screw must be used to stabilize the 1 742 NPT pipe 3 Attach the escutcheon ring to the 1 7 NPT pipe beneath the ceiling tile O Are you adding a camera to the ceiling adapter a pe If Yes proceed to the Securing the Camera optional section on page 11 M5 x 16mm Screw If No you have completed the ceiling adapter installation Page 8 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PP FCTA QL Cs Camera Screw Installation optional Make sure the camera supports one 1 1 4 20 screw Determine which screw hole on the upper adapter plate y
5. ataaaaaannaNaaanaaa naaa aa nanana 8 Securing the Camera Optiomal s 2 scsecvseas casssevea vases eaqesv naa i a a e Ea a N aa aaa ts 9 Technical Specification Ssss a e a E Eaa a a aae a A A E a aa ae EEEN E E EEEa 10 DISGCIGIMEN cennsa a a A A dee A E a Aaa AA DaN EES aetna a 11 Weight Limit THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Manimuni Projector Weight 5O bs i THE PROJECTOR IF NOT THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT
6. oncrete Ceiling 1 Determine a suitable structure capable of supporting the intended weight to drill the mounting holes He Set the holes so that wires from the main ceiling u plate will angle 15 degrees outward see Fig 1 Use a concrete drill bit to drill the mounting holes Place the concrete anchors into the drilled hole and gently tap into place using a rubber mallet or hammer Loop a wire through a concrete anchor bolt see Figure 2 Twist the wire at least five 5 times around itself to secure it Run the other end of the wire through the turnbuckle Twist the wire at least five 5 times around itself to secure it Repeat steps 4 7 for the remaining three mounting points The final loop on the wire has to be tightly bent and secured to prevent it from untwisting Twist the turnbuckles to fine tune adjust Recheck all hardware and installation for proper tightness and security Proceed to the Securing the 1 12 NPT to the PP FCTA on page 11 Installation Instructions Visit the Premier Mounts website at http www mounts com Figure 1 i 4 Eye Lag Screw D C Figure 2 Figure 1 Solid Surface i lt Concrete Anchor D a a anon Figure 2 Page 7 gt 4 24 PP FCTA Ceiling Attachment cont d Truss Ceiling Ceiling Truss 1 Loop the wire around the truss see Figure 1 Hang the wires from the trusses so that they will
7. ou will use to attach the camera Insert one 1 1 4 20 x 2 3 4 pan Phillips head screw commercially available through one 1 wing nut commercially available and the desired screw hole The screw should go through both the upper and lower adapter plates It will later be used to mount the camera A Do not overtighten the mounting screw pan Phillips head screw commercially available lt M 1 4 20 x 2 3 4 lt Wing nut commercially available 1 4 20 optional holes aa eae Ke i am 1 4 20 threaded insert on d S camera ji Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 9 gt 4 22 PP FCTA Technical Specifications All measurements are in inches Page 10 Visit the Premier Mounts website at http www mounts com Installation Instructions PP FCTA Be Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to re
8. place a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 800 368 9700 Warranty claims will not be accepted over
9. t this time Proceed to the Attaching the Turnbuckles section Electrical Box Cut out PP FCTA Upper Plate Assembly Upper Adapter Plate T Bar Frame Rails K 5 x 16mm Combo Screw Tiles Electrical Box Commercially Available Page 6 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PP FCTA Ceiling Attachment Hook the four 4 turnbuckles into the four corners of the main ceiling plate Then choose one of the three ceiling attachment Wood Stud Ceiling 1 Determine a suitable structure capable of supporting the intended weight to drill the mounting holes Set the holes so that wires from the main ceiling WY plate will angle 15 degrees outward see Fig 1 Use a 1 8 drill bit to drill the mounting holes Secure the four 4 4 eye lag screws to the wood stud in the ceiling Loop a wire through an eye lag screw see Figure 2 Twist the wire at least five 5 times around itself to secure it Run the other end of the wire through the turnbuckle Twist the wire at least five 5 times around itself to secure it Repeat steps 4 7 for the remaining three mounting points The final loop on the wire has to be tightly bent and secured to prevent it from untwisting Twist the turnbuckles to fine tune adjust Recheck all hardware and installation for proper tightness and security Proceed to the Securing the 1 2 NPT to the PP FCTA on page 11 C
10. the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2011 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 11
11. wD PREMIER Cag MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS PP FCTA Suspended Ceiling Adapter NORTH AMERICA EUROPE aaaioin GA Genes T Unit 3 The Moorings Business Park USA and Canada Channel Way Longford Conventry CV6 6RH Phone 1 800 368 9700 i Fax 1 800 832 4888 Phone 44 0 2476 644105 Other Locations Fax 44 0 2476 644165 Phone 001 714 632 7100 Fax 001 714 632 1044 9530 302 001 0A gt 4 E PP FCTA Weight LINitoaen einans a aae SEEE OAA SA EA AIEA EA L aA AA a AAAA EAA EA A AAAA 2 Warning Statements ss2esias05 risceiccssidehase dia aazacydaniaevaiisee sietayazsaties AA a NT E S a Aaa Nan A idee 2 Installation TOMS seresa aa a a i tan tye d a aa a a aa a aaa TaT 3 PANS LAS E T A A N EN T 3 Ete OTEA AA E A sits EA EOT AAT E E EATA OO EEN 4 PP FCTA JnstalatiOi viiti iieii ansni aineiden elianna a ean EEEa eae vee AENEA A AAE ELSNER AEE EATEN ANANE 5 Mounting the PP FCTA 000 0022 cccceeeeseeeceeeeeee ce eee ee eee tate aaaea iapa aa aiaa aaa daa aeta anai iaasa daaa iiA 5 Securing the Ceiling Platessa naaa a cased vii a a aaa NAT A E Aa EE a A SASE 6 Electrical Box Cut out Removal cccccccceeeeeeeeeeeeeececaeeaeeeeeeeeeeete cee caaaaecaeeeeeeeeeeeeeccqaaeeaeeeeeeeeeneseeeeccucaeseeeeeeeereees 6 Ceiling Attachmenta niinno a a A A E E E A a 7 Securing the 1 72 NPT Pipe to the PP FCTA seesssseecsrieseserresseerrnaarinnnastinaanannnnaadntannnaatannaa
Download Pdf Manuals
Related Search