Premier PDS-PLUS mounting kit
Contents
1. hinge pins Make sure the bracket is resting on the Base Box before letting go of the projector Insert the four 4 M6 x 12mm tilt adjustment screws two 2 per side You can use either the standard hardware or Lock It security hardware Tighten all screws Do not overtighten the mounting screws Proceed to the Base Box Adjustment section Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 13 gt P PDS PLUS PDS PLUS W Base Box Adjustment You can adjust the roll of the projector by loosening the three 3 front and rear M6 x 12mm screws Do not fully loosen the screws as the mount may drop Set the desired roll and then tighten the screws First tighten the center screws and work your way to the outside screws making any final adjustments prior to tightening the last two screws You can adjust the tilt of the projector by loosening the two 2 M6 x 12mm screws on each side of the Base Box Set the desired tilt and then tighten the screws making any final adjustments prior to tightening the last two screws If your projector is not holding the tilt install the four 4 external tooth washers on the four 4 M6 x 12mm Phillips head screws w Integrated Washers Once all adjustments have been made tighten all hardware Securing the PDS PLUS PDS PLUS W Projector Mount Your PDS PLUS PDS PLUS W Projector Mount incl2. PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the projector If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com P
3. equal height Lower the mounting leg by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise When the desired position is achieved tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench Mounting Hardware Too Long d The depth of some projector mount points may prevent you from tightening the M2 5 and M3 mounting hardware You can reduce the length of the M2 5 and Mounting Hardware M3 mounting hardware by stacking up to a maximum of five 5 M3 flat washers inside the leveling barrel M3 Washer Avoid stacking too many M3 washers the mounting hardware must thread into the Leveling Barrel projector mount point at least four 4 complete Cutaway View turns Page 10 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W 24 Identify the projector s approximate front to back center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from front to back Mentally note the apparent center of gravity Identify the projector s approximate side
4. onto the threaded shaft that is protruding from the ceiling Do not tighten until all nuts and flat washers are in place Proceed to the Attaching the PDS PLUS PDS PLUS W to the Projector section 0000000 Attaching the PDS PLUS PDS PLUS W to the Projector To truly show the versatility of the PDS PLUS PDS PLUS W the following pictures will show a variety of configurations that can be achieved with the PDS PLUS PDS PLUS W Your individual application will depend on the purchased projector Locate the mounting points on the bottom of the projector see arrows above for sample mounting points Proceed to the Attaching the Projector Plate section Page 8 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W 24 Attaching the Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 Marking th
5. AL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy c
6. Instructions Visit the Premier Mounts website at http Avww mounts com Page 15 gt P PDS PLUS PDS PLUS W Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTI
7. Plate if not already attached to each of the mounting legs by inserting and tightening one 1 M6 x 12mm screw through the Projector Plate into the M6 square nut on each of the mounting legs A Do not overtighten the M6 x 12mm screws Insert one 1 Barrel Cap into the end of each leveling barrel except the security leveling barrel Proceed to the Attaching the PDS PLUS PDS PLUS W Base section Single Mounting Point Installation If your projector has only one mounting point a 4 20 x 5 16 screw must be used to attach the mount to the projector Please refer to the following three steps Determine where the mounting point is located Place the projector plate over the mounting point Insert the 20 x 5 16 security screw A Do not overtighten the 20 x 5 16 screw Proceed to the Attaching the PDS PLUS PDS PLUS W Base section Page 12 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W c4 Attaching the PDS PLUS PDS PLUS W Base Place one 1 nylon washer and one 1 flat washer over the hinge pin Insert and tighten one 1 M6 x 12mm screw Repeat O and for the opposite hinge pin You can use either the standard hardware or Lock d It security hardware Replace eight 8 M6 x 12mm screws and one 1 M6 x 8mm set screw Raise the projector with the mounting bracket attached and hook the projector bracket over the
8. The number and placement of mounting points on projectors varies between projector manufacturers Refer to you projector s technical specifications for the number and location of the mounting points on your specific projector Proceed to the Securing the PDS PLUS PDS PLUS W Projector Mount section Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 9 gt P PDS PLUS PDS PLUS W Only attach to the projector manufacturer s specified mounting points on the projector chasis with a minimum three mounting legs Please follow all safety instructions specified by the projector manufacturer as well as the safety instructions outlined in this manual Depending on your application the long mounting legs and the short mounting legs may be used together There are multiple configurations that may be used combining the long mounting legs with the short mounting legs Attach the appropriate number of mounting legs to the projector using the corresponding mounting hardware A Do not tighten the mounting hardware at this time If the mounting legs need to be leveled rotate the leveling barrels to level the mounting bracket To raise the mounting legs rotate the leveling barrel clock wise To lower the mounting leg rotate the leveling barrel counter clock wise itn Raise or lower each of the mounting legs by rotating the leveling barrels until all of the mounting legs are at an
9. age 2 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W 24 Installation Tools The following tools may be required depending upon your particular installation They are not included 7 M3 Security Allen Wrench Supplied Power Drill Pencil Protective Eyewear Phillips Tip Screwdriver M5 Security Allen Wrench Supplied Masonry Drill Bit Ys Wood Drill Bit Tape Measure Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 PDS PLUS PDS PLUS W Mount Hardware Base Box Projector Bracket Mounting Leg Long Mounting Leg Short Qty 1 Qty 1 Qty 4 Qty 2 rew Nylon Spacer Ya Flat Washer Escutcheon Ring Qty 2 Qty 2 Phillips Head Security Head Phillips Head Qty 6 Security Head Qty 12 Qty 1 Qty 1 External Tooth Washer Barrel Cap M6 x 12mm Screw Qty 4 M6 xemm Set screw wiIntegrated Washer Qty 6 Standard Hardware M3 Flat Washer 14 20 x 5 16 Screw M6 x 12mm Screw Qty 10 Qty 1 Qty 4 5 M3 Flat Washer 14 20 x 5 16 Screw M5 x 12mm Screw M6 x 12mm Screw Qty 10 Qty 1 Qty 4 Qty 8 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 3 gt Features PDS PLUS PDS PLUS W Congratulations on the purchase of your
10. been properly secured to the ceiling structure thread the base box to the lower portion of the pipe M3 Security Allen Secure the base box to the pipe with the M6 x 8mm Wrench set screw and tighten it down using the M3 Security Allen wrench supplied Proceed to the Ceiling Installation Wood Stud section Ceiling Installation Wood Stud Use a stud finder to locate a ceiling stud closest to your desired installation location Identify the center of the ceiling stud Use a pencil to mark the location of the ceiling stud center The PDS PLUS PDS PLUS W may be attached to 1 1 2 standard threaded pipe NPT to one of Premier Mount s optional ceiling adapters or to a single wood stud If using an optional adapter please refer to the installation instructions that come with adapters To prevent the stud from splintering use a 1 8 wood drill bit to drill pilot holes Page 6 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W 24 Separate the Upper Bridge from the Base Box by removing the six 6 M6 x 12mm Phillips head screws M6 x 8mm three on each side Set Screw or Security Set Screw Upper Bridge Use the appropriate slot openings for single wood stud mounting depending on your ceiling configuration The adjustable channel slots on the upper bridge plate will allow you to fine tune the final orientation of the projector Sec
11. cD PREMIER Cad MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS PDS PLUS Versatile Projector Mount Model PDS PLUS PDS PLUS W NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9530 009 011 0G PDS PLUS PDS PLUS W Weight Limit einn a a a a a a a aaa A 2 Warning Statome assinei a a E edt veeeastens see eeiehesseednnereneniee 2 InStallation TOOS narena NRO A 3 Pans List eta techie o r a T A E E E N teas cates 3 FF GALUICS centenis n en A a N a OAN 4 odc iO eiaa O a AAO O O 5 Optional Mounting ConiguraionS sepse A A 5 Installing the PDS PLUS PDS PLUS W sioiias ii a E E ca inceeee ey oath dy adivela tee danci 6 Ceiling Installation PPE ee ES A AO 6 Ceiling Installation Wood Stud esna a O OO 6 Calling Installation Solid SUMACE ea r A T 8 Attaching the PDS PLUS PDS PLUS W to the ProjeCt0l c cccccccccisceeecectcceeessstecccssssuetenteedeccceneesdsnchecessdueteceeedsaneeceesnancas 8 Attaching the Projector Plate sscceciccs scecedda onnan RE AAA ONAA A en 9 Selecting the Mounting Hardware sssgcrinsoninn pi E O nae 9 Multiple Mounting Point Installations sssr a O AE cern 9 single Mounting Point Im
12. e 1 8 allowance mark on the small straw or toothpick Aleme as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Set dices Test each size of the screws provided The correct screws should thread easily into the mounting point Sinall Straw of Toothpick and not pull out when tension is applied Does your projector have multiple mounting points or a single mounting point G L um The PDS PLUS PDS PLUS W comes with the option e of using Lock It Security Screws To use the security a screws simply replace the M6 x 12mm Phillips Pan head Small Saw Small Saw screws with the M6 x 12mm security screws Once the hardware has been changed adjust the PDS PLUS PDS PLUS W and tighten down the M6 x 12mm security screws using the M5 Security Allen wrench supplied If your projector has multiple mounting points proceed to the Multiple Mounting Point Installation section If your projector has a single mount point remove the pre installed mounting legs on the universal projector plate and skip to the Single Mount Point Installation section Multiple Mounting Point Installation Locate the projector s mounting points Position an appropriate number of mounting legs on the projector The four long mounting legs come pre installed but you can use three 3 or four 4 long mounting legs and or short mounting legs depending on what the projector requires
13. new Premier Mounts PDS PLUS PDS PLUS W Versatile Projector Mount The PDS PLUS works together with our exciting new PDS Base Box The PDS PLUS PDS PLUS W has multiple mounting configurations to fit a variety of projectors The PDS PLUS PDS PLUS W is truly the most VERSATILE projector mount on the market today Direct Mounting Slots Enable mount to be fastened directly to structural surface Adjustable Leveling Barrels You can quickly level the mounting legs without any specialized tools Low Profile At less than 2 the PDS Series is one of the lowest profile mounts on the market Mounting Slots Allows you to choose from a variety of mounting options and projector mounting point configurations Security Leveling Barrel Allows the user to easily secure the mount with a padlock or a steel cable locking system PCB CSL1 The locks sold separately would make it nearly impossible for anyone to remove the projector from the mount Lock It Security Hardware Protect your projector by installing specialized hardware at critical mounting points Mounting Legs Combined with the numerous projector plate mounting slots the mounting legs allow for near infinite mount configurations Page 4 Visit the Premier Mounts website at http Avww mounts com Installation Instructions b 4 PDS PLUS PDS PLUS W 24 Introduction Your PDS PLUS PDS PLUS W mount may be secured to either a single ceiling stud or a solid surface ceiling s
14. ompleteness or sufficiency of the information contained in this document Premier Mounts 2009 Page 16 Visit the Premier Mounts website at http Avww mounts com Installation Instructions
15. stal lations secarse i odcuels Bae icaeteteale ciules be vu od sucha deatsdetensas OS OO 12 Attaching the PDS PLUS PDS PLUS W Base 0 ecccceecccneeee eee tie eee eee AE N E O EEE 13 Base Box Acjustime ntti sre erei n S AE AOS 14 Securing the PDS PLUS PDS PLUS W Projector Mount sessissrrriecrirnissrriecridi iet ESETT EEEE EEEE EEEE 14 Technical Specifications nsee iaaa a or aara aaa aAa wien eaea a EA ir EN 15 Wanaionases i o a a eer etree O T SA 16 DiscdaiMme i renren O E S ddcauand aceeditnnaevadsenentvagentenday 16 Weight Limit THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Maximum Projector Weight T 5 bs THE PROJECTOR IF NOT THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE TOF PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
16. to side center of gravity Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Place the PDS PLUS PDS PLUS W Projector Plate if not already attached on top of the mounting legs with the center of the plate as close as possible to the i Front to Back projector s center of gravity Center of Gravity Side to Side Center of Gravity Position the legs accordingly for best configuration You may raise or lower each leg independently by Sliding M6 turning the leveling barrels Square Nut Secure the legs to the projector plate by screwing M6 x 12mm security screws into the M6 square nut do not overtighten on the mounting legs Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the PDS PLUS PDS PLUS W Projector Plate If the M6 square nut is not aligned with any slot you UW can use any thin implement such as a toothpick to nudge it into alignment Tighten the mounting screws which secure the mounting legs to the projector Do not overtighten the mounting screws Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 11 gt rH PDS PLUS PDS PLUS W Attach the Projector
17. uch as concrete Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation In addition some steps of this installation may require two people to prevent personal injury and or damage to your projector Please observe all warnings in the following installation procedure and utilize proper safety equipment at all times Optional Mounting Configurations This section contains different configurations if applicable that the PDS PLUS PDS PLUS W can be used with The CLS adapter will be used in conjunction with the PP FCTA and PP FCMA Please refer to the installation instructions that come packaged with the following products PP FCMA I 22202000 GSAoee0000 0 K ee eg K eae Se Standard 1 72 NPT AST 2446 APP 2446 AST 1321 APP 1321 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 5 gt P PDS PLUS PDS PLUS W Installing the PDS PLUS PDS PLUS W Unpack the PDS PLUS PDS PLUS W Mount and familiarize yourself with the components Please take time before you install the PDS PLUS PDS PLUS W to determine the location of where the PDS PLUS PDS PLUS W will be mounted Ceiling Installation Pipe After the pipe has
18. udes one 1 Security Leveling Barrel which can provide additional theft deterrence for your projector Shown below are two examples of how you can use the security leveling barrel to make your projector installation more secure the PCB CSL1 Security Cable sold separately or padlock combination or keyed sold separately Follow the instructions below to install and secure the security leveling barrel If you choose to install the security leveling barrel please follow the instructions outlined below Determine which leveling barrel will be removed Remove the mounting screw Remove the leveling barrel by turning the leveling barrel counter clockwise Thread in the security leveling barrel clockwise Insert and tighten the mounting screw Attach theft deterrent device PCB CSL1 or padlock through the hole that is on the security leveling barrel PCB CSL1 Padlock Combination or Keyed Page 14 Visit the Premier Mounts website at http Avww mounts com Installation Instructions PDS PLUS PDS PLUS W 24 Technical Specifications All measurements are in inches millimeters CUIS 730 190 50 4 50 3 79 095 95 I 114 30 fil 2 00 A TAR i 2 80 o o0 p gt g 50 80 J GA Installation
19. ure the Upper Bridge to the center of the stud on 7 the ceiling structure at this time using two 2 14 x 2 Ceiling Surface wood screws supplied Wood Stud Mounting Slot Upper Bridge 14 x 2 Wood Screw Attach the base box to the upper bridge and secure with the six 6 M6 x 12mm Phillips Head screws above DO NOT OVERTIGHTEN THESE SCREWS AT THIS TIME M6 x 12mm Screw Installation Instructions Visit the Premier Mounts website at http www mounts com Page 7 gt P PDS PLUS PDS PLUS W Ceiling Installation Solid Surface The PDS PLUS PDS PLUS W can be mounted to a ceiling with a minimum 6 thickness Concrete wedge anchors must be used for concrete installation It is recommended that 1 4 wedge anchors be used A concrete bit must be used to drill the pilot hole The concrete wedge anchors and concrete drill bit are commercially available Begin by placing the upper bridge into position against the ceiling keeping it level Mark off four holes to be used for securing the mount and place the upper bridge aside Next drill holes using the appropriate concrete bit for your anchor Insert a concrete anchor into each hole If necessary ahammer can be used to lightly tap each anchor into place so that they are flush with the ceiling Remove the nuts and flat washers from the concrete wedge anchors Once all of the anchors are in place move the upper bridge back into position Attach the nut
Download Pdf Manuals
Related Search