Sony SFM3 flat panel wall mount
Contents
1. DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS THE FLAT PANEL IS HEAVY AND FRAGILE AT LEAST 2 QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL 1 Once the flat panel is inverted use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis Figure 1 2 Using a pencil lightly mark the center of your flat panel Figure 2 Top of Display Inverted Display Inverted Display A 2 A Bottom of Display Figure 1 Flat Panel Mount Location Figure 2 Marking the Display Installation Manual Page 5 SFM3 SONY Mounting Bracket Positioning 1 Lay the left and right mounting brackets stamped arrows facing out Figure 3 Mounting Brackets Arrows Facing OUT Bottom of Flat Panel Figure 3 Mounting Bracket Installation NOTE The mounting guides are designed with a center viewing guide on the side of them There will be a notch cut on the side of the bracket Figure 4 Mounting Bracket Bottom of Flat Panel ES A Center of Center NE ocz Viewing Guide Panel a ga Figure 4 Locating the Center of the Flat Panel 2 Match the center of the viewing guide with the centerline you marked in Step 1 Figure 4 Page 6 Installation Manual SONY SFM3 Griplate 1 The Griplate have M4 M52. M6 and M8 hole patterns to fit the hardware that the flat panel requires Example If your display uses M8 x 20 Phillips head screws Use the M8 mounting points Figure 5 Dimples M8 O O M6 M5 M4 Figure 5 Griplate Orientation 2 Once the mounting brackets are aligned secure the Griplate to the flat panel NOTE The dimples of the top plates have to be facing up and the bottom dimples must be facing down Use 1 Griplate per mounting point Figure 6 CAUTION Do not over tighten the mounting hardware ms u TO SO No DNPLES Phillips Screw FACING u Driver Bottom Flat Panel ee Figure 6 Griplate Attachment Installation Manual Page 7 SFM3 SONY Wood Stud Location 1 Using a stud finder locate the 16 or 24 stud centers behind the wall 2 Once found make a pencil mark on the center of the wood studs Figure 7 a Stud Finder Mark Wooden Studs Figure 7 Locating the Wooden Stud 3 Measure from the floor to the desired viewing height and mark the wall Figure 8 NOTE This marking will reference the center of your flat panel display once mounted to the wall Measure and Mark the Desired Viewing Height on the Wall Figure 8 Measuring the Height Piden O Page 8 Installation Instructions SFM3 SONY 4 Use the information below when mounting to the
3. OF THE DISPLAY IF NOT THE WALL STRUCTURE MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH WARNING SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY WARNING PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION gt O gt gt pog INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE Indicates that the power plug is to be disconnected from the power outlet Contact Sony Electronics with any questions Safety precautions must be taken at all times Warning and Caution statements Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the display and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the display and could increase the risk of fire At least two qualified people should perform the installation procedure In
4. SONY SFM3 Securing the Flat Panel to the Wall Mount WARNING At least 2 qualified personnel are strongly recommended for installation of this product Failure to do so could result in serious injury and possible damage to the flat panel 1 Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod on the wall plate Figure 13 Wall Plate ne A Wf of Ps KR y We ats a s DS DN G U LAWA BOTTOM Figure 13 Securing The Flat Panel Lateral Shift Adjustment 1 Make any lateral shift adjustment and lock it by tightening the two 2 4 20 Phillips screws found on the bottom of the mounting brackets Figure 14 2 Use the foot leveler to adjust your plasma CAUTION Do not over tighten the Y4 20 screws to the rods Leveling Foot Ya 20 Screw Figure 14 Lateral Shift Adjustment Installation Manual Page 11 SONY SFM3 CSL1 Security Cable 1 2 Page 12 Installation Manual SONY SFM3 Technical Specifications All measurements are in inches mm OOD 8 8 8 U a 16000 406 4 pi 406 4 24290 re 61
5. following surfaces Figure 10 Wood Studs Drill four 4 14 pilot holes to the marked wall Concrete Wall Drill four 4 3 8 pilot holes to the marked wall RY i Z RAT Drill Gun Pilot Holes Figure 10 Mounting Surfaces Securing the Wall Plate to the Wooden Studs 1 Level and secure the plate to the wall with the reference arrow facing up to ceiling 2 Secure the plate using four 4 5 16 lag bolts and flat washers Figure 11 CAUTION Do not over tighten the lag bolts NOTE The wall plates have three 16 and 12 mounting slot positions Level 5 16 x 3 lag bolt and flat washer YV N lt Wall Plate Figure 11 Securing the Wall Plate Installation Manual Page 9 SONY SFM3 Securing the Wall Plate to a Concrete Wall 1 Level and secure the plate to the wall with the reference arrow facing up to the ceiling 2 Use a minimum diameter of 5 16 x 2 14 wedge anchors commercially available Figure 12 CAUTION Do not over tighten the wedge anchor bolts NOTE Use a minimum diameter of 5 16 x 2 4 long wedge anchors 5 16 x 2 14 Wedge Anchors Wall Plate Figure 12 Concrete Installation Page 10 Installation Manual
6. 6 97 193 49 3 A Wall plate B Mounting brackets C GriplateTM D Mounting hardware E Safety screws F Leveling feet G Wood stud H 5 16 x 3 Lag screws and flat washers Installation Manual Page 13 SFM3 SONY Warranty Limited Lifetime Warranty This product carries a limited lifetime warranty from ship date against defects in materials and workmanship Sony Electronics is not liable for improper installation that results in damage to mounts adapters display equipment or personal injury Customer Support In the event of missing and or damage equipment or technical questions the following information can help in the completion of the installation Customer Service 877 350 3477 Notes Sony Electronics Inc 16540 West Bernardo Drive San Diego CA 92127 800 222 7669 www sony com Sony 2006 IN SFM3 R0 Page 14 Installation Manual
7. SONY INSTALLATION MANUAL SFM3 Sony Electronics Inc IN SFM3 R0 16540 West Bernardo Drive San Diego CA 92127 www sony com SFM3 SONY SONY Table of Contents WARNING STATEMENTS ut pa RA O WWO O O 3 PARTS al Silt RE ORO os Ria IS O O DD AS A ee On eS artic 4 INSTALLATION TOOES seria lidad adas 4 FLAT PANEEMOUNTTEOCATION eos zo a dacia dadas lada 5 MOUNTING BRACKET POSITIONING ceccccccccccccssssssescsccccscsssnsssceccesssseessusesscssssesuusasecesessseeenens 6 GRIPLATE Mi a A e e OM ats fake Sh Le ea 7 WOODESTUDBDEOCATION za lc a o i A AE ches tts ones iches tte a aaa tienes etececseteds 8 SECURING THE WALL PLATE TO THE WOODEN STUDS eeee aaa aaa uwaa aa aaa aaa wawa aaa owaocieca 9 SECURING THE WALL PLATE TO A CONCRETE WALL eeeeee ooo aaa eee aaa aaa aa wawa wawa awaaniee 10 SECURING THE FLAT PANEL TO THE WALL MOUNT conoccccnnnnccccnonononnnanecanccncnnonnnnanonoconcnnnnnnnnnninicinannns 11 LATERAL SHIFT ADJUSTMENT ect ai WBA W ci 11 CSET SECURITY CABLE Ee ca o O A ad A aia 12 TECHNICAL SPECIFICATIONS artine ann a e a a a iii t T E E TE E E 13 MARRA N ad a ti ata cade Ses 14 CUSTOMERSUBPORE 00 RO NOWA e er dde ch 14 NOTES Guara a e rl dd 14 Page 2 Installation Manual SONY SFM3 Warning Statements WARNING THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE 5 TIMES THE WEIGHT
8. jury and or damage can result from dropping or mishandling the plasma display Recommended mounting surfaces wooden studs and solid flat concrete If the mount is to be installed on any surface other than wooden studs use suitable hardware which is commercially available Installation Manual Page 3 SFM3 SONY Parts List NOTE This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Sony Electronics 877 350 3477 Wall Plate Qty 1 Mounting Brackets Qty 2 Griplate Qty 4 M6 x 16mm Phillips Pan 5 16 x 3 Lag Bolts Qty 4 Wooden studs only 5 16 Flat Washers Metal Qty 4 M5 x 16mm Phillips Pan Head Screws Qty 4 9 9 b ow SH Z lt 9 9 PCB CSL1 Security Cable Qty 1 Installation Tools Phillips Head Screw Driver Portable Drill Soft Material Blanket Pencil Socket Page 4 Y4 Drill Bit Tape Measure Level Supplied Wrench with 1 2 Drive Installation Manual SONY SFM3 Flat Panel Mount Location WARNING INVERT THE FLAT PANEL PLACE IT ON A SOFT FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL USE A BLANKET FOAM ETC FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL
Download Pdf Manuals
Related Search