Chief MAC118B mounting kit
Contents
1. 20 SNAPTOGGLE BB 1 1 4 20 N 1 3 16 118 Installation Instructions Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center Display Mount Installation Location Must be centered on studs There must be a minimum of 1 7 8 48mm clearance behind wall Drywall 1 2 minimum Drywall Thickness Both Sides of Stud i Steel Stud 2 x 4 25 WU Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 962 S 125 18 C Shaped S Stud Section Figure 1 Installation Instructions Preparation of Existing Mount If mount has previously been installed 1 Remove display from mount following instructions provide2. INSTALLATION INSTRUCTIONS J Series Steel Stud Installation Kit CHIEF MAC118 Our Mounts Your Vision 118 DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Befestigungsteil festziehen festziehen Apertar fixador il ee vastdraaien a les fixations Fastener Installation Instructions WARNING Fai
3. at washer K onto button head capscrew L 13 Insert Phillips pan head capscrews L with flat washer K through mounting hole in display mount and into anchor M and tighten until flush against mount DO NOT overtighten WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel Stud Drywall K x 4 L x 4 Display Mount Anchor Metal Channel SIDE VIEW Figure 8 MAC118 118 CH F USA International Our Mounts Your Vision Europe Chief Manufacturing a division of Milestone AV Technologies Asia Pacific 8804 000344 RevD 2008 Milestone AV Technologies www chiefmfg com 06 08 Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA 2 RAY B tK Bb E P 86 755 8996 9226 F 86 755 8996 9217 p TI U gt
4. d with mount 2 Remove mount from wall following instructions provided with mount 3 Proceed to step 4 If mount has not previously been installed 4 Remove mount wall plate from swing arm assembly by removing screw washers and spacers pivot pin and locknut See Figure 2 Screw Swing Arm Washers Pivot Pin Existing Wall Plate MAC118 NOTE Wall plate and hardware removed is not required for steel stud installation It may be discarded or kept for future use in a non steel stud application Assemble Swing Arm to Steel Stud Wall Plate To assemble the mount 1 Orient swing arm so that it is positioned in front of mounting tabs on wall plate A See Figure 3 2 Slide inner stud C up into bottom of swing arm 3 Place spacer G up against bottom of swing arm and hold spacer G and inner stud C in place 4 Slide swingarm with inner stud C and spacer G between mounting tabs in wall plate A 5 Slide stepped spacer D spacer E and washer F onto flat head cap screw 6 Slide flat head capscrew B with spacers E and washer F down into swing arm and through inner stud C and lower spacer 7 Secure swing arm to mount using Nylock nut Figure 3 118 Mount Installation After determining the site meets the installation requirements 1 Identify desired mounting location on wall 2 Using a stud finder or similar method locate studs 3 Align mou
5. lure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this kit is attached can support five times the combined weight of all equipment WARNING This kit is intended for use only with Chief JWD and JWS Swing Arm Wall mounts WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 75 lbs 34 1 kg Hex Head Wrench Zeskantsleutel Cl a t te hexagonale Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips e gt Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Installation Instructions MAC118 TOOLS REQUIRED FOR INSTALLATION AND PARTS g il 0 1 2 013mm 3 16 oor e E 1 K 4 he 1 4 20 L 4 G 1 4 4 20 x 1 3 4 Z M 4 lt 1 4
6. nting holes in mount with studs making sure mounting holes are centered on studs WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting holes are used on both sides 4 Mark location of four mounting holes on wall 5 Drill four 1 2 813mm holes 1 2 013mm x4 Mounting holes centered on studs Figure 4 6 Hold metal channel on anchor M flat alongside plastic straps and slide channel through hole Installation Instructions Drywall Plastic Straps Figure 5 Holding plastic straps on anchor M pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud as show in figues below Slide plastic cap on anchor M towards wall until flange of cap is flush with wall Steel Stud Drywall Plastic Cap Z 4 Anchor Metal Channel SIDE VIEW Figure 6 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap 10 Repeat steps 6 through 9 for each mounting hole Installation Instructions Steel Stud Drywall Plastic x ZV Plastic Straps Anchor Metal Channel SIDE VIEW Figure 7 ZZ 11 Place mount over anchors and align mounting holes in display mount with holes in anchors 12 Place fl
Download Pdf Manuals
Related Search