Chief MWR6044B flat panel wall mount
Contents
1. Lower Swing Arm Mounting Plate Hex Head Cap Screw and Washer ADE 2 O Figure 4 Installation Instructions MWR Cover Installation To install channel covers 1 Installupper and lower wall channel covers B by tipping cover top down and positioning as shown in end view of figure below See Figure 5 2 Tap firmly across bottom of channels B to lock in place as shown in figure below See Figure 5 3 Install R H and L H end caps F by aligning tabs on end caps F with slots in wall channel covers B and sliding tabs in until end caps F are flush with wall channel covers B See Figure 5 L x END VIEW Figure 5 MWR Installation Instructions Display Installation If the mounting pattern of the display being installed is a VESA standard 200 x 200 pattern the mounting2. Figure 1 Installation Instructions MWR Mount Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL 7 32 6mm x4 INJURY OR DAMAGE TO EQUIPMENT It is the installer s A responsibility to make sure the structure to which the MWR is being installed is capable of supporting five times the combined weight of the mount and all attachments 1 Determine mounting location taking into consideration display size and mount movement 2 Using a stud sensor locate two wood studs 16 apart on center See Figure 2 3 Using two people place mount against wall and level mount aligning mounting holes in upper and lower wall channels with studs See Figure 2 4 Use a pencil mark four mounting holes making sure mounting holes are located as close as possible to center of studs See Figure 2 5 Drill four pilot holes where the mounting holes were marked using a 7 32 6mm drill bit See Figure 2 6 Using two people place mount against wall aligning mounting holes in upper wall channel with pilot holes 7 Install two 5 16 x 2 1 2 lag bolts G and two 135 thick washers H through upper wall channel and into pilot holes DO NOT tighten at this time See Figure 3 8 Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wal
3. clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension See Figure 12 and See Figure 13 DECREASE Figure 12 INCREASE Figure 13 Installation Instructions MWR 11 MWR C CH F USA International Our Mounts Your Vision Europe Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific 8831 000008 RevH 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 08 10 p TU gt TI gt Tl Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 on cO A CONSUMES
4. destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 125 lbs 56 7 kg Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Npucnoco6bTecb Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabe a sextavada Chiave esagonale Ce Zeskantsleutel Cl t te hexagonale naBHbIN BeAbMoN PbIBOK Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme OtTBeptka Installation Instructions MWR TOOLS REQUIRED FOR INSTALLATIO
5. INSTALLATION INSTRUCTIONS Medium Flat Panel Wall Mount CHIEF Our Mounts Your Vision MWR DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND Tighten Fastener Apretar elemento de fijacion Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations CoxmnTe 3acTexkxy Loosen Fastener Open Ended Wrench Installation Instructions A CAUTION A CAUTION alerts you to the possibility of damage or
6. N AND PARTS SNI a 7 32 516 x 2 112 H 4 850x 395x 135 MWR DIMENSIONS NOTE CUSIOM INTERFACE BRACKET NOTSHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1 2 AND 2 IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT SEE MSB XXXX DRAWING ALSO Mounting Pattem Extended 632 24 90 25 __ 178 1 00 7 00 i ee a s qa 61 2 39 ate S s Bos S m i 397 15 65 lt g M 4 2 g _ _ c axe 64 J 226 2 51 8 89 B 406 al 16 00 Unit Depth Retracted Tilted Up 87 3 43 Installation Instructions PRODUCT FEATURES WEIGHTCAPACIIY 125 Lbs HEIG HT AD USIMENT o TILT ROLL YAW 5 15 2 5 0 N ALL MEASUREMENTS ARE IN THE FOLLOWING FORMAT MILLIMETERS INCHES Tilt Adjustment Tilted Down ags a AG T 2 5
7. buttons can be installed directly to the back of the display If the display has any other mounting pattern an interface bracket must be obtained before proceeding Consult a Chief Customer Service representative if an interface bracket is required Remove pin and nuts and move to lower holes WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons A padlock or bolt may on display are properly seated in mounting holes in faceplate be placed through latch holes To install display 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall Figure 7 See Figure 6 2 While supporting both sides of display align four mounting CABLE MANAGEMENT buttons on display or interface bracket with four mounting holes in faceplate See Figure 6 l a WARNING IMPROPER INSTALLATION CAN LEAD TO 3 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly SERIOUS PERSONAL INJURY OR DAMAGE TO seated in lower area of mounting holes and click lock EQUIPMENT Make sure cables do not run through pinch mechanism has enga
8. ged See Figure 6 and points See Figure 7 1 Loosen front and rear cable clamps on top arm See Figure 8 2 Thread cable ties E under cable clamps and secure clamps to top arm See Figure 8 3 Route power audio video cables through the cable channel in top arm See Figure 8 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4 Secure cables to top arm using two cable ties E 5 Repeat steps 1 through 4 for lower arm WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate Figure 6 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 7 Installation Instructions From Display Figure 8 ADJUSTMENTS Pitch Tension Adjustment To adjust display pitch tension 1 With display installed tighten or loosen two screws one on each side using a 5 32 hex wrench See Figure 9 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained MWR Figure 9 MWR Roll Adjustment The MWR allows for the horizontal alignment Roll of the display
9. l channel Mounting holes 9 Install two 5 16 x 2 1 2 lag bolts G and two 135 thick centered on washers H through mounting holes in lower wall channel studs and into pilot holes See Figure 3 10 Tighten all hardware DO NOT overtighten Figure 2 Figure 3 MWR Installation Instructions Mount Lateral Position Adjustment The MWR is designed to allow up to 5 of right or left lateral adjustment after being mounted to the wall This lateral adjustment can be used to more precisely position where the center of the display is located when installation is complete To adjust the mounts lateral position 1 Remove display if installed 2 While holding swing arm remove two hex head cap screws and two washers securing swing arm to upper wall channel See Figure 4 3 While holding swing arm remove two hex head cap screws and two washers securing swing arm to lower wall channel 4 Sethardware aside for reuse See Figure 4 5 Slide swing arm left or right until desired location is reached making sure mounting holes in swing arm upper and lower mounting plates align with mounting slots in upper and lower wall plates See Figure 4 6 Secure swing arm to upper and lower wall channels using hex head cap screws and washers set aside during steps 1 and 2 See Figure 4 ADE Hex Head Cap Screw and Washer Upper Swing Arm Mounting Plate Upper Wall Channel
10. to be adjusted up to 2 right or left to level the display after installing To adjust Roll 1 Loosen the roll tension adjustment nut located on the back side of the faceplate assembly See Figure 10 2 Level display 3 Tighten roll tension adjustment nut See Figure 10 Figure 10 Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar C and adjustment wrench D 2 Place adjustment bar C into socket head cap screw located at swing arm pivot point See Figure 11 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE If changing from a smaller display to a larger display may be necessary to increase swing arm tension 10 Installation Instructions Socket Head Capscrew Figure 11 Using the adjustment wrench D turn adjustment bar C
Download Pdf Manuals
Related Search