Chief KWGSK110S flat panel wall mount
Contents
1. 1 2 minimum Drywall Thickness Both Sides of Stud Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 S 125 18 C Shaped S Stud Section Figure 1 Mount Installation After determining the site meets the installation reguirements Installation Instructions KWGSK110 1 Identify desired mounting location on wall 2 Using a stud finder or similar method locate studs a 3 Align mounting holes in mount with studs making sure mounting holes are centered on studs See Figure 2 Plastic Straps 4 Mark location of three mounting holes on wall 5 Drill three 1 2 13mm holes See Figure 2 1 2 013mm x3 Figure 3 7 Holding plastic straps on anchor L pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud as show in figues below See Figure 4 8 Slide plastic cap on anchor L towards wall until flange of cap is flush with wall See Figure 4 Steel Stud Drywall Plastic Cap Anchor Metal Channel Mounting holes centered on studs SIDE VIEW Figure 2 Figure 4 9 Snap off plastic straps on anchor at wall by pushing side to 6 Hold metal channel on anchor L flat alongside plastic Side spia odio off spe level with Aage of paai cap2. IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket 1 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENTS for detail 2 Using Phillips screwdriver carefully install two screws E into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 7 Pick up and align display so that screws E installed on the back of the display in the previous step fit into the mounting holes on the Centris bracket rotate the bracket as required See Figure 7 Lower the display into place Centris Bracket Figure 7 Using Phillips screwdriver install two remaining screws E through the lower mounting holes in Centris bracket and into display 5 Tighten all four screws E Do not overtighten 6 Proceed to CABLE MANAGEMENT RECESSED MOUNTING HOLES 1 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail Carefully place display face down on protective surface 3 Determine depth of recessed moun
3. INSTALLATION INSTRUCTIONS Small Flat Panel Steel Stud Wall Mount E CHIEF KWGSK110 Our Mounts Your Vision KWGSK110 Installation Instructions DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations WARNING Failure to read thoroughly understand and follow all instructions can result in
4. crew counterclockwise towards the symbol If display rises on its own then rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw Adjustment Screw Figure 13 Centris Head 1 If previously attached disconnect cables from display then remove display 2 Using Phillips screwdriver slightly loosen or tighten the adjustment screw as necessary See Figure 14 Adjustment Screw Phillips Screwdriver Figure 14 Installation Instructions KWGSK110 KWGSK110 Installation Instructions 10 Installation Instructions KWGSK110 11 KWGSK110 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8832 000217 RevD 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 09 USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA AI Th RR AN BS ak Bb Bp XE DPR 24F P 86 755 8996 9226 F 86 755 8996 9217 Asia Pacific PA A 2 A O Fconsume
5. n CLOSED Position View from Bottom cl Figure 9 CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched when bracket is closed 3 Carefully insert cables into bracket See Figure 10 Cable Management Bracket in open position Cable Path typical NOTE Display not shown for clarity Figure 10 4 Close cable management bracket by sliding it back towards the centerline of the arm NOTE If necessary cable management bracket attach screws may be tightened using hex key M CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched by installation of cover C or screws E 5 Carefully insert cables in cavity located in lower portion of mount arm See Figure 11 6 Using Phillips screwdriver install cover 10 with two screws 20 See Figure 11 KWGSK110 Installation Instructions Cable Path typical C x 1 E x3 Figure 11 ADJUSTMENTS Swing Arm PIVOT SWING 1 Using 3 16 hex key slightly loosen or tighten the adjustment screw s as necessary See Figure 12 Adjustment Screws Figure 12 Height Adjustable 1 Using 5 32 hex key slightly loosen or tighten the adjustment screw as necessary See Figure 13 If display settles on its own then rotate adjustment s
6. pschroevendraaier Tournevis pointe cruciforme Installation Instructions TOOLS REGUIRED FOR INSTALLATION AND PARTS lt D 1 2 013mm Ps PJ A 1 flat panel wall ont M4 x 20 8 E 4 M4 x 12 F 4 e 1 2 x 3 K 3 1 4 20 x 1 3 4 A L 3 cable management over 2 Si 3 3 8 P 4 G 4 1 2 x 3 8 H 4 O M4 x 20 x 1 4 20 SNAPTOGGLE BB M 1 N 1 a 3 16 a 5 32 KWGSK110 Installation Instructions Site Reguirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud Display Mount Installation Location Must be centered on stud A If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center There must be a minimum of 1 7 8 48mm clearance inside wall Drywall
7. serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this kit is attached can support five times the combined weight of all eguipment Reinforce the structure as reguired before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 25 Ibs 11 3 kg Hex Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Gw Cacciavite a stella Kruisko
8. strapsandslidechannelthroughhole SeeFigure3 See Figure 5 10 Repeat steps 6 through 9 for each mounting hole KWGSK110 Installation Instructions Steel Stud Drywall Plastic Cap Plastic Straps Anchor Metal Channel SIDE VIEW Figure 5 11 Place mount over anchors and align mounting holes in display mount with holes in anchors See Figure 6 12 Place flat washer J onto Phillips pan head screws K 13 Insert Phillips pan head screws K with flat washer J through mounting hole in display mount and into anchor L and tighten until flush against mount DO NOT overtighten WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel Stud Drywall K x 3 J x3 Display Mount Anchor Metal Channel SIDE VIEW Figure 6 Display Installation The mounting holes on the back of your display will either be flush with the back surface or recessed into the back surface Refer to the applicable installation procedure Flush Mount Display WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes WARNING
9. ting holes relative to back surface of display against which Centris head will contact See Figure 8 gt N Installation Instructions KWGSK110 4 Select proper length spacer and screw See Figure 8 NOTE All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer 5 Place the four selected spacers over each of the mount holes on the back of the display 6 Pick up and orient the mount A so that the mounting holes in the Centris bracket are aligned with the holes in the spacers rotate the bracket as required See Figure 8 Centris Bracket Figure 8 WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes 7 Using Phillips screwdriver install four screws D or H through the mounting holes in Centris bracket through the spacers F or G and into the display See Figure 8 8 Tighten all four screws Do not overtighten CABLE MANAGEMENT 1 Attach all cables to display 2 Open the cable management bracket by sliding it towards the edge of the arm See Figure 9 NOTE If necessary cable management bracket attach screws may be loosened using hex key M Attach Screws RT OPEN Positio
Download Pdf Manuals
Related Search