SYBA CL-37004518 card reader
Contents
1. Digital audio connector 5 Serial ATA Port First Make sure the 4 pin power cable that from Power supply 1s connected to the correct location of the I O board and then plug the Serial ATA cable connecting to the Serial ATA port on the Motherboard from I O PANEL ARR gd i hr rn ah y i Li mal Apin connector to ipower supply j connect with sata cable These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives ERE HY tF kazi kal w End ORE SATA connectors 6 Card Reader Connect with the 5 pin USB cable from CNI location of the Card reader PCB to another USB port where is on the motherboard USB 5V USE Pa USE GND NC USB 8 i a otis liar USB 2 0 connectors mmm pnm caw 2532 1 USB 2 0 Port These two 4 pin Universal Serial Bus ports are available for connecting with USB 2 0 devices 2 IEEE 1394 This 6 pin firewire connector is for IEEE1394 device 3 SM Connector This port is used for connecting with memory SM card 4 CF MD Connector This port is used for connecting with memory CF or MD card 5 SD MMC Connector This port is used for connecting with memory SD or MMC card 6 MS Connector This port is used for connecting with memory MS card 7 8 S PDIF digital sound Connector The technology turns your computer into a high end entertainment system with a digital connector for powerful audio and speaker2. User s Manual GENERAL SPECIFICATION Front panel I O BOX with connected cables INSTALLATION A Make sure the computer power is off after shut down the computer and then open the cover of the computer B Remove the 5 25 plastic cover from the computer where is the free bay you want to install b oe C Install the I O front panel to the empty bay and screw it D Connect the attached cables from the I O FRONT PANEL to the correct connectors where are on the motherboard when the I O FRONT PANEL BOX is installed E Connect with the Power Connector from the power supply to I O Front Panel Please refer to the picture below power connector for power supply 1 USB Port Plug the USB module cable to the USB 2 0 connectors which 1s on the motherboard mA O O obe SER USB 2 0 connectors ng Ona 258 258 2 Audio Port Plug in the Audio Module Cable to the legacy AC 97 Audio pin header where is located on the motherboard Azalia compliant Legacy AC 97 compliant pin definition pin definition PRESENCE SENSE1_RETUR SENSE RETLR 2 2 399 TTJ NEZD HH id a 35 5 l r Analog front panel connector 3 1394 Port Plug the 1394 cable to the 1394 Port where is on the motherboard and make sure all the pins of connector which 1s connected are correct IEEE 1394 Connector z 4 SPDIF_OUT Connect the S PDIF module cable to the S PDIF connector which is on the Motherboard
3. systems 9 Microphone Connector This port is used to connecting with a microphone 10 LINE OUT Connector This port is used to connecting with a headphone or a speaker 11 DC Power Connector This 4 pin connector is used for connecting with SATA Power 12V or 5V 12 SATA Connector This port is used for connecting with Serial ATA Equipment The cables choose Here you can choose the kinds cables that attached to IJO BOX PIN ASSIGNMENT PIN 488 IGNMENT EE i PIN ASSIGNMENT DRAIN 1 PIN ASSIGNMENT GREEN 3 COLOR P5 L COLOR Pa BLACK 4 FED i YELLOWS WHITE 2 ORANGE 6 GREEN 3 RED s BLACK 4 BROW 101 DRAIN 5 L2 n o il em P4 ib L Liam ri B PS arm B u LET LU PIEDI L5 a Po RESEDA ur j n 7 P7 PINE 41 R STGPUJ PLIN DT Bad jem PI B Es IG MENT PIN ASSIGWENT nM MR GOR P3 Le an KED 1 m If IH TH TH BLACK 4 Ground DRAIN EL Gouw DRAIN SHELE c pound SLE P5 B COLOR PA 16 DRAIN CHUMO DRAIN 3 WHITE EDIF IN WHITE 2 RED Wm 1 IIN BIOS setup program USB Configuration The items in this menu allows you to change the USB related features Select an item then press lt Enter gt to display the configuration options BIOS SETUP UTILITY USB Configuration Enables USB host controllers Module Version 2 23 2 9 4 USB Devices Enabled None USB Fonction Enabled Legacy USB Support A
4. uto USB 2 0 Controller Enabled USB 2 0 Controller Mode HiSpeed VA The Module Version and USB Devices Enabled items show the auto detected values If no USB device is detected the item shows None USB Function Enabled Allows you to enable or disable the USB function Configuration options Disabled Enabled Legacy USB Support Auto Allows you to enable or disable support for USB devices on legacy operating systems OS Setting to Auto allows the system to detect the presence of USB devices at startup If detected the USB controller legacy mode is enabled If no USB device is detected the legacy USB support is disabled Configuration options Disabled Enabled Auto USB 2 0 Controller Enabled Allows you to enable or disable the USB 2 0 controller Configuration options Disabled Enabled USB 2 0 Controller Mode HiSpeed Allows you to configure the USB 2 0 controller in Hispeed 480 Mbps or Full Speed 12 Mbps Configuration options HiSpeed Full Speed
Download Pdf Manuals
Related Search