Baumatic BT06.7ME cooker hood
Contents
1. Instruction manual User Manual for your Baumatic BT06 7ME BTO8 7ME 60 cm Integrated hood ii _ Baumatic You will be mine NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it ts easily available for future reference for you or any person not familiar with the operation of the appliance DD 18 09 07 Contents Page Environmental note IMPORTANT SAFETY INFORMATION Specifications of your cooker hood Using your Baumatic cooker hood Cleaning your Baumatic cooker hood The grease filter Maintenance Removing and cleaning the grease filter BT06 7ME Removing and cleaning the grease filters BT08 7ME Changing a light bulb Fitting the carbon filters Installation Electrical connection Before beginning installation Installing your cooker hood Connecting to external ducting Extraction mode or recirculation mode Completing the installation Troubleshooting Contact details 8 10 10 10 11 11 12 13 14 15 15 16 17 20 21 22 22 23 24 25 ENVIRONMENTAL NOTE Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent p2. BT06 7ME 49 65 dB BT08 7ME Optional Extra 1 x CFM1 carbon filter for air recirculation mode BT06 7ME 2x CFM1 carbon filters for air recirculation mode BT08 7ME available from the Baumatic Spares Department Using your Baumatic cooker hood Before first use IMPORTANT THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME o You should clean the appliance using a brand new cloth with warm soapy water before using the appliance for the first time You should then dry it thoroughly using a soft cloth To use your cooker hood Viotor on indicator neon Light ON OFF Speed control slider slider o Make sure that it has been installed by a suitably qualified person as per the information contained in Baumatic s installation instructions o Find the control panel which can be located by opening the front panel and looking on the right hand side of the cooker hood o There are two sliders on the control panel which perform separate functions Light ON OFF slider 0 1 Light bulb off Light bulb on Motor on indicator neon This will light when the motor is switched on using the speed control Slider Speed control slider Off Low speed Medium speed High speed El Es IMPORTANT IDEALLY YOU SHOULD TURN ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK OR AT THE VERY LEAST WHEN YOU BEGIN COOKING YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER
3. If other types of flue or appliances are fitted ensure that there is an adequate supply of air in the room When the hood is being used in extraction mode ensure that the ducting is fire retardant and that there are no bends greater than 90 degrees as this will reduce the efficiency of the hood Ensure the ducting for the extractor mode has the same diameter as the outlet hole all the way through Keep young children from using playing with or tampering with the cooker hood Older children and infirm persons should be supervised if they are using the cooker hood Your cooker hood is for domestic use only Please dispose of the packing material carefully children are especially vulnerable to it Dirty oil is an even greater fire risk Always put lids on pots and pans when cooking on a gas cooker Eo The manufacturer refuses to accept any responsibility for damages arising to the hood or for it catching on fire from a failure to observe the fire safety advice contained in these instructions o Remember that when in extraction mode your cooker hood is removing air from your room Ensure that proper ventilation measures are being observed o Note that the cooker hood removes odours from your kitchen not steam o Warning Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood including cleaning and replacing light bulbs o Do not connect the duct
4. Netherlands 3136 549 1555 25 26 21 Baumatic WWW baumatic com
5. Prior to touching the light bulbs ensure that they have cooled down o Find the bulb that requires replacement you will find it located in the light fixture which is inside the exposed section of the canopy E74 40 imax o Unscrew the light bulb that needs to be replaced and insert a new olive shaped bulb with an E14 coupling 40W max o IMPORTANT Defective bulbs should be replaced immediately o If the lights still do not work make sure that the bulbs are fitted properly into their housings before you call for technical assistance o Refit the grease filter and close the front cover Fitting the carbon filters If the appliance is going to be used in recirculation mode then it is necessary to fit carbon filters This will help to absorb unpleasant odours caused by cooking IMPORTANT BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY 13 o Open the front screen and remove the grease filter as described on page 11 or 12 o If you are replacing the existing carbon filter then you need to remove it by twisting it anti clockwise o Hook the carbon filter over the central fixing box on the motor o Turn the carbon filter clockwise until you feel it click into place o BTO8 7ME only Repeat this process for the second carbon filter You need to place a carbon filter over both motors o Refit the grease filter and cl
6. YOU HAVE FINISHED COOKING Cleaning your Baumatic cooker hood IMPORTANT BEFORE CLEANING ALWAYS ENSURE u THAT YOU HAVE SWITCHED YOUR COOKER HOOD THE OFF AT THE OMNI POLAR SWITCH SET AT THE WALL FROM THE CABLE Cleaning O Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth Never use abrasive powder corrosive solvents or brushes Never insert pointed objects into the motor s protective grid Only clean the control panel and grease filter grill with mild liquid detergents and a new damp cloth If you are using the appliance in recirculation mode then be sure to replace the carbon filters at the recommended interval see section on Fitting the carbon filter A build up of grease could cause a fire hazard Never attempt to clean the area above the grease filter The grease filter O O Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen amp furniture from greasy residues The metallic filter may become flammable if it becomes saturated with this greasy residue o To prevent this fire hazard the filter should be cleaned regularly O Depending on use this should be done every 10 15 days or at least once a month using hot water and normal washing up detergent DO NOT WASH THE GREASE FILTER IN A DISHWASHER 10 Maintenance Removing and cleaning the grease filter BTO6 7ME o To
7. access the grease filter open the front panel and push the two catches A upwards o To take out the grease filter you should remove it from the flexible wire flame o Soak the grease filter in hot water and washing up liquid for about an hour o Rinse it off thoroughly with hot water o Repeat the process if required o Refit the grease filter once it has dried o You should wipe over the front panel in hot soapy water with a damp cloth and then dry it thoroughly with a soft cloth o Close the front cover o IMPORTANT Let the grease filter dry thoroughly before refitting it in the cooker hood 11 Removing and cleaning the grease filters BTO8 7ME o Open the front cover Remove the grease filters by pulling down on their handles and then pulling them upwards away from the main body of the cooker hood o Soak the grease filters in hot water and washing up liquid for about an hour o Rinse them off thoroughly with hot water o Repeat the process if required o Refit the grease filters once they have dried and then close the front cover o IMPORTANT Let the grease filters dry thoroughly before refitting them in the cooker hood 12 Changing a light bulb IMPORTANT BEFORE ATTEMPTING TO CHANGE A LIGHT BULB YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY o Open the front cover and remove the grease filter as described on page 11 or 12 o
8. hood using the screws and washers E supplied Check that the adjustment screw F is fitted 4 Measure a distance of 1050 mm between the highest point on the hob top and the wall that you will be fixing the hood to You Should also measure and record the distance between the top of the extractor mounting brackets D o Using a pencil mark this height and then attach the two mounting brackets G to the wall at this height using the screws provided They should be positioned the same distance apart as the extractor mounting brackets D IMPORTANT These screws must be securely tightened o Hook the extractor mounting brackets D that you fixed to the hood in step 3 onto the mounting brackets G 5 Some adjustment is provided within the extractor mounting brackets Use screw E to adjust the front to back alignment of the hood Use screw F to adjust the height alignment of the hood o Once you have finished adjusting the position of the hood fully tighten all of the screws 6 If there is a gap between the rear of the cooker hood and the rear wall There is a spacer provided that can be cut to the size of the gap and attached to the rear of the cooker hood 7 IMPORTANT The cooker hood must now be fixed to the adjacent cabinets using the screws provided You should screw through the holes in the side of the hood into the adjacent cabinets THESE SCREWS MUST BE FULLY TIGHTENED 8 Place the front panel again
9. blue and brown neither must be connected to the earth terminal 15 O USE A 3 AMP FUSE As the colours of the wires in the appliance s mains lead may not correspond with the coloured markings identifying the terminals in your spur box please proceed as follows o The blue wire must be connected to the terminal marked N neutral or coloured black o The brown wire must be connected to the terminal marked L live or coloured red Before beginning installation O Check that the product purchased is of a suitable size for the chosen installation area In addition check whether there is an electrical socket available that will be accessible once the hood is mounted If the product is going to be used in extraction mode then there should also be space to connect a ducting hose to the outside Carry out all necessary masonry work prior to the fitting of the cooker hood Ensure that all electrical connections are carried out by a suitably qualified person Before commencing installation of the cooker hood the grease filter should be removed Check inside the product and ensure that there is no transit packaging or any other materials such as packets of screws guarantees etc These should be removed and kept for future use If possible disconnect and move freestanding or slot in cookers from their position to provide easier access to the rear wall and cupboards If this is not possible then a th
10. erson CONFORMITY TO W E E E DIRECTIVE This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol st on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact the Baumatic Technical Department IMPORTANT Any installation work must be carried out by a qualified electrician or competent person o The hood must be installed in accordance with the installat
11. ick protective covering should be placed over the worktop hob top or cooker This will help to protect these surfaces from damage and debris Select a flat surface for assembling the cooker hood Cover that surface with a protective covering and place all cooker hood parts and fittings on it Do not tile grout or silicone this appliance to the wall or cabinetry This appliance is designed to be surface mounted only 16 Installing your cooker hood IMPORTANT YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE PLEASE TURN TO PAGES 21 22 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES o We recommend that at least two people install this hood o Your cooker hood should only be fitted to a wall and secured between two cupboards o It must be positioned at least 700 mm above the hob underneath it This measurement should be taken from the highest point on the hob including the burners IMPORTANT YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED 1 Open the front panel and push the two catches A upwards Then remove the grease filter or grease filters 17 2 Whilst the front panel is still open remove the two screws B Press the tab C down and remove the front panel from its guide rails 3 Secure the extractor mounting brackets D onto the top of the
12. ing system of this appliance to an existing ventilation system being used for any other purpose o Do not install above a cooker with a high level grill o Never leave frying pans unattended during use as overheated fats and oils might catch fire o The cooker hood should not be exposed to a direct heat source from the cooking device underneath it i e naked flame from a gas burner or heat from electric hob zones without a pan on them o Do not attempt to use the cooker hood if it is damaged in any way Never attempt to use it without the grease filter fitted or if the filter is excessively greasy o Never flamb cook under this cooker hood o The lights on this appliance should only be used during operation of the cooker hood They should not be left on permanently and used as a lighting source THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE FOR INSTALLATION MAINTENANCE AND SUITABLE USE OF THE HOOD Specifications of your cooker hood Congratulations on purchasing a Baumatic Cooker Hood DIMENSIONS Width canopy 599 mm Depth canopy 2 0 mm Height canopy 380 mm Your Cooker Hood is fitted with o Twin motor BT08 7ME ONLY o Slider control operation o 3 Speeds o 1 light BT06 7ME ONLY o 2 lights BT08 7ME ONLY o Aluminium filter included o Extraction capacity 330 m hr BT06 7ME 440 m3 hr BTO8 7ME o Noise level min max 48 61 dB
13. ion instructions and all measurements followed o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 amp BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building Standards Scotland Consolidated Regulations issued by the Scottish Development Department o It is dangerous to alter the specifications or to modify this product in any way Do not tamper with or attempt to modify the appliance in any way o When installing the hood ensure that the following recommended distances are observed between the highest point on the hob top including the burners and the bottom of the cooker hood gt Electric cookers 700 mm gt Gas cookers 700 mm gt Coal oil cookers 800 mm IMPORTANT DO NOT SET YOUR COOKER HOOD LESS THAN 700mm ABOVE YOUR COOKER o When installed between adjoining wall cabinets the cabinets must not overhang the hob The edges of the cooker hood are sharp be mindful of this as you handle your appliance especially during installation and cleaning DO NOT CLEAN IN BEHIND THE GREASE FILTER If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type
14. k that the hood is connected to the electricity supply o Check that the fan speed control is set correctly D My cooker hood is not working effectively o The fan speed is not set high enough o The grease filter is dirty and requires cleaning o The kitchen is not well ventilated enough o Ifthe hood is set up for recirculation mode check that the carbon filters do not need replacing o Ifthe hood is set up for extraction mode check that the ducting hose and discharge outlet are not blocked D My cooker hood has switched off during operation o The safety cut out device has been tripped o Turn off the hob and then wait for the safety cut out device to reset o IMPORTANT If you have installed your cooker hood too low the safety cut out device will frequently trip Your cooker hood may become damaged if the safety cut out device is tripped frequently 23 IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number 0118 933 6911 DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your a
15. ose the front screen o The carbon filters should be replaced every three months or if they show signs of damage 14 Installation IMPORTANT Before installation and usage read all the instructions and make sure that the voltage V and the frequency Hz indicated on the rating plate are exactly the same as the voltage and frequency in your home The rating plate can be found behind the grease filter The manufacturer declines all responsibility in the event of the installer failing to observe all of the accident prevention regulations in force which are necessary for normal use and the regular operation of the electric system Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION o The cooker hood s power cable must be fitted upstream from the electrical connection using an omni polar switch with a contact distance of at least 3 mm THE FUSE MUST BE RATED AT 3 AMPS WARNING THIS APPLIANCE MUST NOT BE EARTHED It should only be connected by a competent person using fixed wiring via a double pole switched fused spur outlet UK ONLY We recommend that the appliance is connected by a qualified electrician who is a member of the N I C E I C and who will comply with the I E E and local regulations The wires in the mains lead are coloured in accordance with the following UK code Blue Neutral Brown Live You will only find two wires in the main s lead
16. ppliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance when it is delivered 24 gt Baumatic You will be mine United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Service Telephone 0118 933 6911 Service Fax 0118 986 9124 Spares Telephone 01235 437244 Technical Advice Telephone 0118 933 6933 E mail sales baumatic co uk technical baumatic co uk Website www baumatic co uk Republic of Ireland 01 6266 798 Czech Republic Baumatic CR SPOL S R O 46215 Librec The Czech Republic 4204 8357 7200 www baumatic cz Germany Baumatic GMBH Janderstrasse 9 Mannheim 68199 Germany 4962 112 9190 www baumatic de Italy Baumatic Italia S R L Via Caltana 129 Campodarsego Padova 35011 Italy 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grind Zuigerstraat 22 ALMERE 1333 MS The
17. rs for purification The air then re enters the kitchen via an opening in the hood For optimum performance we recommend that the cooker hood is used in extraction mode and connected to external ducting Unfortunately if you live in a flat or the hood is too far from an outside wall this may not be possible The only alternative is to recirculate the alr Do I need a charcoal filter All cooker hoods have a grease filter but if you are using your cooker hood in recirculation mode then charcoal filters must be fitted in addition to the grease filter Completing the installation If you are setting the appliance to recirculation mode then you should now fit the two carbon filter s See the Fitting the carbon filters section on page 14 The electrical connection must correspond to the electrical requirement noted on the rating plate which is placed inside the cooker hood The appliance should now be connected to the electrical supply See page 15 16 for detailed information on the electrical connection Refit the grease filter s and then switch on the mains supply to the appliance Check that the appliance is operating correctly by selecting each speed and switching the light bulbs on and off 22 Troubleshooting IMPORTANT If your cooker hood appears not to be operating properly before contacting the Baumatic Service Department please refer to the checklist below D My cooker hood will not start o Chec
18. st the furniture door Using the screws provided secure the front panel of the cooker hood to the inner surface of the furniture door Make sure that these screws are fully tightened o Reattach the front panel to the front of the cooker hood 20 Connecting to external ducting ll o Connect the coupling to the top or the rear of the cooker hood and then connect a 125 mm ducting hose to the coupling please note that the ducting hose is not supplied with the appliance o You may find an anti draft flap included with the fixtures and fittings for the cooker hood You should sit this in the top of the coupling o If you use the rear or top venting position the other one should be blocked off using the blanking plate supplied o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours It should have a cross section of at least 150 cm o The maximum distance between the coupling and your discharge outlet should be 3 metres with one 90 degree bend 21 Extraction mode or recirculation mode IT IN EXTRACTION MODE OR RECIRCULATION MODE What is the difference between extraction and recirculation modes In extraction mode the stale air will be taken via the grease filter and out of the room via external ducting In recirculation mode stale air is taken via the grease filter and passed through charcoal filte
Download Pdf Manuals
Related Search