HP Compaq S1922a
Contents
1. 1922 S1922a and S2022a LCD Monitor User Guide 2010 Hewlett Packard Development Company L P Microsoft Windows and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein This document contains proprietary information that is protected by copyright No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Document Part Number 603427 001 First Edition January 2010 About This Guide This guide provides information on setting up the monitor installing drivers using the on screen display menu troubleshooting and technical specifications Z WARNING Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life A CAUTION Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information A NOTE Text set off in this manner provides important supplemental information Table of Contents About This Guide 1 Product Features AP R2. Be sure the computer and monitor are turned off and unplugged 1 To connect the VGA cable Connect one end of the VGA video cable to the back of the monitor and the other end to the VGA video connector on the computer 2 To connect the DVI D cable provided with select models Connect one end of the DVI D video cable to the back of the monitor and the other end to the DVI D video connector on the computer You can use this cable only if your computer has a DVI compliant graphics card installed The monitor DVI D connector and cable are included Figure 3 7 Connecting the VGA or a DVI D cable connector locations may vary EY NOTE When using a VGA or DVI signal you must connect your audio separately because a VGA or DVI signal converts only video data not audio data Connecting the Audio Cable Select Models Connect the built in monitor speakers to the computer by using the audio cable as shown in the following illustration Figure 3 8 connecting the Audio Cables connector locations may vary ENWW Connecting Monitor Cables 7 High Bandwidth Digital Content Protection HDCP Available on Select Models Your monitor supports HDCP and can receive high definition content High definition content is available in many sources such as Blue ray Disc devices or HDTV air or cable broadcasts If you do not have an HDCP enabled monitor you will see a blank screen or a lower resolution picture when playing high definition p
3. HES HE AY MET BER GE X AAA WMA Hy MD TE a BRI AE 39 H H T B 5 S thy SJ T 11363 2006 br HE R He AY Pd HL BE AR Pw X WBT RR ATE WM RoHS EA RNIN LALA Z 2003 T 1 H 27 KF He He Re Bh hR STE HH L HR H TI H 2002 95 EC 5144 E PEE RBA TA A ER TIE IEA AA 30 ENWW Turkey EEE Regulation In Conformity with the EEE Regulation EEE Y netmeligine Uygundur 31
4. N A Adjust picture Clock to reduce 0 100 Do Auto Setup 1 Vertical Line noise Configure Each step will increase decrease value by 1 Phase N A Adjust Picture Phase to 0 100 Do Auto reduce Horizontal Line noise Configure H Position N A Adjust the horizontal position 0 100 Do Auto of the picture Configure V Position N A Adjust the vertical position of 0 100 Do Auto the picture Configure Image N A Select Image Aspect Ratio Wide Default to panel Ratio native aspect ratio 13 Appendix 4 Operating the Monitor ENWW ENWW ESE i LN Red Green Blue Color Temp Color Temp 4 User 0 Ra 5 COC 1 60 0 ma 1 50 Main Main Sub Adjust Menu Item Menu Icon Menu Item Description Range Reset Value Color Temp Warm Recall Warm Color N A The Color 0 Temperature Temperature will ee be set to Warm Normal Recall Normal Color N A Temperature The User R G B Cool Recall Cool Color N A value default is Temperature 50 will can be Modified by Reset sRGB Recall sRGB Color N A function in user for select Temperature mode models with sRGB function Red Red Gain from Digital 0 100 register Each step will increase decrease value by 1 Green Green Gain from Digital 0 100 register Each step will increase decrease value by 1 Blue Blue Gain from Digital 0 100 register Each step will increase decrease value by 1 Using the On Screen Display
5. OSD 14 OSD Setup H Position V Postion Timeout Language 0 m 150 0 15 130 4 English gt CE EN Main Main Sub Adjust Menu Item Menu icon Menu Item Description Range Reset Value OSD Setup H Position Adjust the horizontal position 0 100 Recall 50 Value D of the OSD Each step will increase decrease value by 5 V Position Adjust the vertical position of 0 100 Recall 50 Value the OSD Each step will increase decrease value by 5 Timeout Adjust the OSD timeout 5 100 Recall 10 Value Each step will increase decrease value by 5 Language Set OSD display language to English No need to recall English English is default Espa ol language while setting Francais Press RESET Portugu s Pycckuin If customer have R Kh T different request ESTA please refer to ato customer request Appendix 4 Operating the Monitor ENWW ENWW Extra Input Select D SUB gt DDC CI lt On amp Reset Yes gt Information Resolution 1280 H x 1024 V _H Frequency 64KHz g 60Hz Main Main Sub Adjust Menu Item Menu icon Menu Item Description Range Reset Value Extra Input Select Select video input signal D SUB Note Analog wa Available DVI Only Model no 2 on Select Input Select Models item DDC CI Select DDC CI on or off On Off Reset Clear each old status of Auto Yes
6. lock slot for a locking security cable security cable sold separately Plug and Play capability if supported by your computer system On screen display OSD adjustments for ease of setup and screen optimization choose English Spanish French Portuguese Russian Simplified Chinese Traditional Chinese Korean Power Saver to reduce energy consumption HDCP High Bandwidth Digital Content Protection on DVI input for select models Software and utilities CD containing the following Drivers Documents Ie HP LCD Monitors 1 2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor If another cord is used use only a power source and connection appropriate for this monitor For information on the correct power cord set to use with the monitor refer to the Connecting the Power Cable A WARNING To reduce the risk of electric shock or damage to the equipment Do not disable the power cord grounding feature The grounding plug is an important safety feature e Plug the power cord in a grounded earthed outlet that is easily accessible at all times Disconnect power from the product by unplugging the power cord from the electrical outlet For your safety do not place anything on power cords or cables Arrange them so that no one may accidentally step on or trip over them Do not pull on a cord or cable When unplugging from the electrical outlet grasp the cord b
7. sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet and the total ampere rating of the products connected to the power cord does not exceed the rating of the power a Cas on the power label to determine the ampere rating Amps or A for each device Install your monitor near a power outlet that you can easily reach Disconnect the monitor by grasping the plug firmly and pulling it from the outlet Never disconnect the monitor by pulling the cord Chapter 2 Safety and Maintenance Guidelines ENWW Do not allow anything to rest on the power cord Do not walk on the cord Maintenance Guidelines To enhance the performance and extend the life of the monitor Do not open the monitor cabinet or attempt to service this product yourself Adjust only those controls that are covered in the operating instructions If the monitor is not operating properly or has been dropped or damaged contact an authorized HP dealer reseller or service provider Use only a power source and connection appropriate for this monitor as indicated on the label back plate of the monitor Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet and the total ampere rating of the products connected to the cord does not exceed the rating of the cord Look on the power label to determine the ampere rating AMPS or A for ea
8. 4 x 768 48 36 60 00 5 1280 x720 45 00 60 00 6 1280 x 1024 63 98 60 02 7 1440 x 900 55 93 59 88 8 1600 x 900 55 54 60 00 Appendix B Technical Specifications ENWW LCD Monitor Quality and Pixel Policy ENWW Your LCD Monitor uses high precision technology manufactured according to high standards to help guarantee trouble free performance Nevertheless the display may have cosmetic imperfections that appear as small bright or dark spots This is common to all LCD displays used in products supplied by all vendors and is not specific to your LCD Monitor These imperfections are caused by one or more defective pixels or subpixels A pixel consists of one red one green and one blue subpixel A defective whole pixel is always turned on a bright spot on a dark background or it is always off a dark spot on a bright background The first is the more visible of the two A defective subpixel dot defect is less visible than a defective whole pixel and is small and only visible on a specific background To locate defective pixels the monitor should be viewed under normal operating conditions and in normal operating mode at a supported resolution and refresh rate from a distance of approximately 50 cm 16 inches We expect that over time the industry will continue to improve its ability to produce displays with fewer cosmetic imperfections and we will adjust guidelines as improvements are made For more information about your LCD
9. Monitor refer to the HP Web site at http www hp com support 25 C Agency Regulatory Notices Federal Communications Commission Notice ENWW This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for help Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett Packard Company may void the user s authority to operate the equipment Ca
10. N A configuration and set the color temperature to Warm Do not execute reset return No to main menu Information Show the resolution H V N A N A frequency and input port of current input timing Using the On Screen Display OSD 16 Selecting Video Input Connectors The input connectors are VGA connector analog DVI D connector digital Select Models The monitor automatically determines which inputs have valid video signals and displays the image You can connect the VGA cable the DVI D cable or both If both cables are installed the default input selection is DVI The source of input can be switched using the Input Select option in the OSD menu Identifying Monitor Conditions Special messages appear on the monitor screen for the following monitor conditions Input Signal Out of Range When the Hsync Frequency Vsync Frequency or Resolution is out of the monitor support range will show this message This message will be flying No Signal When the video cable is not connected or the video cable is connected but there is no Active signal input will show this message after 9 seconds the monitor will enter power saving This message location is at the position setting in OSD Setup item Auto Adjustment in Progress Indicates the auto adjustment function is active See Adjusting Screen Quality in this chapter Adjusting Screen Quality The auto adjustment feature automatically fine tunes the image qualit
11. ar uo E eu eee KR ARR a ara ts Mey eben a a a 27 German Ergonomics Notice 0 000 ccc tte 27 JapanesesNotices A II as TEK A om manele Cass oa Manele Sr Task bile ao 28 Korean Notice 547 KR Na eae eek Sey Ri ae A eee Pe ee deve Ge ea eet 28 Power Cord Set Requirements eer ee eee eee eb ee aie a eR ere es Peet a oe ee 28 Japanese Power Cord Requirements 0 0 0 cent teen tees 29 Product Environmental Notices ere triin ee eke il rie aby tae bee ebay aad nadie bine ine da aca T E TR 29 Materials DISPO tae 29 Disposal of Waste Equipment by Users in Private Household in the European Union sx ss K reiini tenes 29 Chemical Ee s Te TTT 29 HP Recycling sle Ta 29 Restriction of Hazardous Substances ROHS 0 0 cect tet 30 Turkey EEE Regulation 2c iiet i Ea EE R aT seed A we wee Gl eee peda eb dae art 31 1 Product Features HP LCD Monitors ENWW The HP LCD liquid crystal display monitors have an active matrix thin film transistor TFT screen with the following features Large diagonal display Maximum graphics resolution 1922 1366 x 768 60Hz S1922a 1366 x768 60Hz S2022a 1600 x 900 60Hz Plus full screen support for lower resolutions VGA analog signal DVI digital signal on select models Easy viewing from a sitting or standing position or while moving from one side of the monitor to the other Tilt adjustment Removable base Built in stereo speakers on select models Security
12. ay Type TFT LCD active matrix Viewable Image Size 47 cm 18 5 in diagonal Tilt 4 4 2 18 2 Maximum Weight unpacked 3 2 kg 7 04 Ibs Dimensions h x w x d 340 95 mm x 440 3 mm x 180 mm 13 5 x 17 4 x 7 in Maximum Graphics Resolution 1366 x 768 60 Hz Optimum Graphics Resolution 1366 x 768 60 Hz analog mode Text Mode 720 x 400 Dot Pitch 0 3 x 0 3 mm 0 01 x 0 01 in Horizontal Frequency analog mode 30 to 83 kHz Vertical Frequency analog mode 55 to 75 Hz Environmental Requirements Temperature independent of altitude Operating Temperature 41 to 95 F 5 to 35 C Non Operating Temperature 4 to 140 F 20 to 60 C Relative Humidity non condensing Operating Humidity 15 to 90 Non Operating Humidity 5 to 90 Power Source 100 240V 50 60 Hz Power Consumption 37 watts W Sleep Power Consumption lt 1 0 watts W Appendix B Technical Specifications ENWW ENWW Table B 3 Model S2022a Specifications Display Type TFT LCD active matrix Viewable Image Size 50 8 cm 20 in diagonal Tilt 4 4 2 18 2 Maximum Weight unpacked 3 4 kg 7 48 Ibs Dimensions h x w x d 355 7 mm x 472 8 mm x 180 mm 14 x 18 6 x 7 in Maximum Graphics Resolution 1600 x 900 60 Hz Optimum Grap
13. bles Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations 26 Declaration of Conformity for Products Marked with the FCC Logo United States Only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation For questions regarding the product contact Hewlett Packard Company P O Box 692000 Mail Stop 530113 Houston Texas 77269 2000 Or call 1 800 HP INVENT 1 800 474 6836 For questions regarding this FCC declaration contact Hewlett Packard Company P O Box 692000 Mail Stop 510101 Houston Texas 77269 2000 Or call 281 514 3333 To identify this product refer to the Part Series or Model number found on the product Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada German Ergonomics Notice HP products which bear the GS approval mark when forming part of a system comprising HP brand computers keyboards and monitors that bear the GS approval mark meet the applicable ergonomic r
14. ch device Install the monitor near an outlet that you can easily reach Disconnect the monitor by grasping the plug firmly and pulling it from the outlet Never disconnect the monitor by pulling the cord Turn the monitor off when not in use You can substantially increase the life expectancy of the monitor by using a screen saver program and turning off the monitor when not in use Slots and openings in the cabinet are provided for ventilation These openings must not be blocked or covered Never push objec ts of any kind into cabinet slots or other openings Do not drop the monitor or place it on an unstable surface Do not allow anything to rest on the power cord Do not walk on the cord Keep the monitor in a well ventilated area away from excessive light heat or moisture When removing the monitor base you must lay the monitor face down on a soft area to prevent it from getting scratched defaced or broken Cleaning the Monitor H M gt Turn off the monitor and the computer Unplug the monitor from the wall outlet or the power brick Clean the monitor plastics with a clean cloth dampened with water Clean the monitor screen with an antistatic screen cleaner A CAUTION Do not use benzene thinner ammonia or any other volatile substances to clean the monitor or the screen These chemicals may damage the cabinet finish as well as the screen ENWW Maintenance Guidelines 3 3 Setting Up the Monitor Unpacking
15. ei eiee T sooo ics A a a Ss ceed 1 2 Safety and Maintenance Guidelines Important Safety Information gt 03 co AA AA AA te ap es Ge RR ta ae 2 Safety Pre tons isopen erot eae Vee A aH AR A Reta Ole ous bly adh wed Atlee Atle es dla aie Fae owe late A aa 2 Maintenance Guidelines ig TR 57 rinne ia ee R TR E lean STR AT Ease ere ay Gane BER Reed AE a eee as Ae eta eee 3 Cleaning the Monitor ocio Bose eee de ete ete OS EE ee Re ae eer Rise ees 3 3 Setting Up the Monitor Unpacking the Monitor Savi eA eee a ee a ee eed eee eae a eee aes 4 Installing the Monitor ses eied eos do Bact ree esa a ees eee aa Dee eee ples aed 4 Connecting Monitor Cables xes ss e a ne berea cieta RRR tnt teas 7 Connecting the Audio Cable Select Models 00 cc eee ee 7 High Bandwidth Digital Content Protection HDCP Available on Select Models comio ri as A da 8 Connecting the Power Cable sss 200 5 e aK se bebe ebb ee eee bob ee bet ee ds borio e erase 8 Adjusting the Tiltss 2 2 cata ecb at eke ine ad ak ete ip cadet wo etn eave Oh Gee ee Ph eae Weibel deadbeat 9 4 Operating the Monitor CD Software and Utilities e cis poche eae eee AA Ae ae Ae Bh ey Ques 10 Installing Drivers 7 one e a A A A te dae teed eae 10 Installing the monitor driver software from the CD teens 10 Downloading updated drivers from the Internet 00000 tee eee 10 Front Panel Controls tresci iio daea K KR RR RE R TERE R Bt os Pies dea e
16. equirements The installation guides included with the products provide configuration information 27 Appendix C Agency Regulatory Notices ENWW Japanese Notice Korean Notice COREA JOABDRRRAHRECT COREL RER te CHEAT SOCCER BMELTUETM TORE AY TLE Vay Sia RI HEL TEA Nat RIBES HOF CERHVETF BHEN HHI HE AC IE LL RY RWS LC Fat VCCI B Ol WAS ASRBHLS AIS GTS E INEA F SE JHON Ad Hop AS YN or a Al 10M A ge Suc Power Cord Set Requirements ENWW The monitor power supply is provided with Automatic Line Switching ALS This feature allows the monitor to operate on input voltages between 100 120V or 200 240V The power cord set flexible cord or wall plug received with the monitor meets the requirements for use in the country where you purchased the equipment If you need to obtain a power cord for a different country you should purchase a power cord that is approved for use in that country The power cord must be rated for the product and for the voltage and current marked on the product s electrical ratings label The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product In addition the cross sectional area of the wire must be a minimum of 0 75 mm2 or 18 AWG and the length of the cord must be between 6 feet 1 8 m and 12 feet 3 6 m If you have questions about the type of power cord to use contact an authorized HP service provider A power cord sh
17. ere you can drop off your waste equipment for recycling please contact the local city office the household waste disposal service or the shop where you purchased the product Chemical Substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH Regulation EC No 1907 2006 of the European Parliament and Council A chemical information report for this product can be found at http www hp com go reach HP Recycling Program HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs go to http www hp com recycle 29 Appendix C Agency Regulatory Notices ENWW ENWW Restriction of Hazardous Substances RoHS A Japanese regulatory requirement defined by specification JIS C 0950 2005 mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1 2006 To view the JIS C 0950 material declaration for this product visit http Awww hp com go jisc0950 20084 ERI AHA NMEA RTRA ISCO AREN ELT E EFKE 20064791 ALBANIA EFRON RE CR YEADOS RIOT ELTMABRERMEARAANION ELA RI BLOD SHH R ITOFELTIE www hp com go iscO09504SRLT lt REEL ABAZUR LRHAMRARR STR BHAA R SREB MD mes Os ZEH BE AT IA AA NIE H PL 0 gt IR RIE SJ T 11363 2006 br
18. erly Adjust H Position and V Position or press hot key AUTO Picture has color defects white does not look white Adjust RGB color or select color temperature Horizontal or vertical disturbances on the screen Use Windows shut down mode Adjust CLOCK and Phase or press the Auto button to display ideal setting Appendix A Troubleshooting ENWW Getting Support from hp com Before you contact customer service refer to HP Technical Support at http www hp com support Select your country region and then follow the links to the support page for your monitor Preparing to Call Technical Support If you cannot solve a problem by using the troubleshooting tips in this section you might have to call technical support For technical support contact information refer to the printed documentation included with the monitor Have the following information available when you call Monitor model number located on label on back of monitor Monitor serial number located on label on back of monitor or in the OSD display in the Informationmenu Purchase date on invoice Conditions under which the problem occurred Error messages received Hardware configuration Name and version of hardware and software you are using Locating the Rating Label The rating label on the monitor provides the product number and serial number You may need these numbers when contacting HP about your monitor model The rati
19. feature of the monitor to work you need a Plug amp Play compatible computer amp video card Check with your computer manufacturer Also check the monitor s video cable and make sure none of the pins are bent Make sure the HP Monitor Drivers are installed HP Monitor Drivers are available at http www hp com support Picture Is Fuzzy amp Has Ghosting Shadowing Problem Adjust the Contrast and Brightness Controls Make sure you are not using an extension cable or switch box We recommend plugging the monitor directly to the video card output connector on the back of your computer Picture Bounces Flickers Or Wave Pattern Is Present In The Picture Move electrical devices that may cause electrical interference as far away from the monitor as possible Use the maximum refresh rate your monitor is capable of at the resolution your are using Monitor Is Stuck In Active Off Mode The Computer Power Switch should be in the ON position The Computer Video Card should be snugly seated in its slot Make sure the monitor s video cable is properly connected to the computer Inspect the monitor s video cable and make sure none of the pins are bent Missing one of the primary colors RED GREEN or BLUE Inspect the monitor s video cable and make sure that none of the pins are bent Make sure the monitor s video cable is properly connected to the computer Screen image is not centered or sized prop
20. hics Resolution 1600 x 900 60 Hz analog mode Text Mode 720 x 400 Dot Pitch 0 2768 x 0 2768 mm 0 01 x 0 01 in Horizontal Frequency analog mode 30 to 83 kHz Vertical Frequency analog mode 55 to 75 Hz Environmental Requirements Temperature independent of altitude Operating Temperature 41 to 95 F 5 to 35 C Non Operating Temperature 4 to 140 F 20 to 60 C Relative Humidity non condensing Operating Humidity 15 to 90 Non Operating Humidity 5 to 90 Power Source 100 240V 50 60 Hz Power Consumption 37 watts W Sleep Power Consumption lt 1 0 watts W 23 Preset Video Modes 24 The monitor automatically recognizes many preset video input modes that will appear properly sized and centered on the screen Table B 4 Factory Preset Video Input Modes S1922 S1922a Item Preset Resolution Horizontal Frequency kHz Vertical Frequency Hz 1 640 x 480 31 47 59 94 2 720 x 400 31 47 70 09 3 800 x 600 37 88 60 32 4 1024 x 768 48 36 60 00 5 1280 x720 45 00 60 00 6 1280 x 960 60 00 60 00 7 1280 x 1024 63 98 60 02 8 1366 x768 47 71 59 79 Table B 5 Factory Preset Video Input Modes S2022a Item Preset Resolution Horizontal Frequency kHz Vertical Frequency Hz 1 640 x 480 31 47 59 94 2 720 x 400 31 47 70 09 3 800 x 600 37 88 60 32 4 102
21. is in normal operating mode the Power light is blue and the monitor uses the normal watts of power For power usage refer to Technical Specification Appendix B The monitor also supports a power saver mode that is controlled by the computer When the monitor is in the reduced power state the monitor screen is blank the backlight is off and the Power light is amber The monitor uses minimum power When the monitor is awakened a brief warm up period occurs before the monitor returns to normal operating mode The energy saving reduced power state activates if the monitor does not detect either the horizontal sync signal or the vertical sync signal The power saver feature must be activated on your computer for this feature to work Refer to your computer documentation for instructions on setting energy saver features sometimes called power management features amp NOTE The energy saver feature works only when the monitor is connected to computers that have energy saver features Power Saver Feature 18 A Troubleshooting Solving Common Problems The following table lists possible problems the possible cause of each problem and the recommended solutions Problem Solution Problem amp Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor No Plug amp Play In order for the Plug amp Play
22. l outlet installed 8 Chapter 3 Setting Up the Monitor ENWW Adjusting the Tilt For optimal viewing adjust the screen tilt to your own preference as follows 1 Face the front of the monitor and hold the base so that you do not topple the monitor while changing the tilt 2 Adjust the tilt by moving the top edge of the monitor either toward or away from you without touching the screen Figure 3 10 Tilt adjustment ENWW Adjusting the Tit 9 4 Operating the Monitor CD Software and Utilities The CD that is included with this monitor contains drivers and software that you can install on your computer Installing Drivers If you determine that you need to update the drivers you can install the monitor driver INF and ICM files from the CD or download them from the Internet Installing the monitor driver software from the CD To install the monitor driver software from the CD 1 ak oN Insert the CD in your computer CD drive The CD menu appears Select the language Click Install Monitor Driver Software Follow the on screen instructions Ensure that the proper resolutions and refresh rates appear in the Display Control Panel settings Refer to the Windows operating system documentation for more information EY NOTE You might need to install the digitally signed monitor drivers INF or ICM files manually from the CD in case of an installation error Refer to the Driver Software Readme file on the CD f
23. ne Bee Ruan newts acyl dere 11 Using the On Screen Display OSD ret 2 ee ee ree be a eee be be eee weber eee 12 Selecting Video Input Connectors comic oe bed eee ei i cee Eb de die TRN Beene dE CRL ean 17 Identifying Monitor Conditions na es eee a e o a a r aa a a an a aita O Ea OAE a E e E E iena 17 Adjusting Screen Quality petes eeen nire nne ea a A E e E se eed a ai 17 POWER SAVE Features senh o iaia a Rata a RR RR Ea pith Foden A a a a E a iaei 18 ENWW iii A Troubleshooting Solving Common Problems e204 oiee acdc yah bce athe eye A a tt 19 Getting Support from GGG iia dee nk oe ee e CSR PER EES Ree gee RRR ope aera 20 Preparing to Call Technical Support TE Rc o KR Te S R e 9 E RTE KER 9 aR a e eA RAER REN RRR EaR 20 Locating the Sane abel gt lt 2 sos Ta s carers oases diareeha aS a RE a Oa See ales fase 20 B Technical Specifications HP LED MonitOrs ssi d a K a eerie Z ee a eae reals SE aye ere rd ace aE sop E ERT ER R did 21 Preset Video NIGGA H a a A NAAL A A ads 24 LCD Monitor Quality and Pixel Policy 25 C Agency Regulatory Notices Federal Communications Commission Notice ttt t eee 26 Modifications ensa pcb dba a god deed deen pee ao odes 26 CABIOS X T aad E octal sweats aay tt lal EAR AE HRH oS RANN Ra Sate 26 Declaration of Conformity for Products Marked with the FCC Logo United States Only a uuuaaaaa auauna 27 Canadian Notice voi te ie oe a sy Bee 27 Avis Canadiense pa
24. ng label is on the back of the monitor ENWW 20 B Technical Specifications All specifications represent the typical specifications provided by HP s component manufacturers actual performance may vary either higher or lower HP LCD Monitors Face treatment Glare polarizer with hard coating Input terminal VGA connector DVI D 24 pin D type connector select models Table B 1 Model S1922 Specifications Display Type TFT LCD active matrix Viewable Image Size 47 cm 18 5 in diagonal Tilt 4 2 18 2 Maximum Weight unpacked 3 2 kg 7 04 Ibs Dimensions h x w x d 340 95 mm x 440 3 mm x 180 mm 13 5 x 17 4 x 7 in Maximum Graphics Resolution 1366 x 768 60 Hz Optimum Graphics Resolution 1366 x 768 60 Hz analog mode Text Mode 720x400 Dot Pitch 0 3 x 0 3 mm 0 01 x 0 01 in Horizontal Frequency analog mode 30 to 83 kHz Vertical Frequency analog mode 55 to 75 Hz Environmental Requirements Temperature independent of altitude Operating Temperature 41 to 95 F 5 to 35 C Non Operating Temperature 4 to 140 F 20 to 60 C Relative Humidity non condensing Operating Humidity 15 to 90 Non Operating Humidity 5 to 90 Power Source 100 240V 50 60 Hz Power Consumption 37 watts W Sleep Power Consumption lt 1 0 watts W ENWW 21 22 Table B 2 Model S1922a Specifications Displ
25. or instructions in English only Downloading updated drivers from the Internet To download the latest version of drivers and software files from the HP Support site 1 2 3 4 ENWW Refer to http www hp com support Select your country region Select Download Drivers and Software Enter the model number of your monitor The software download pages for your monitor are displayed Download and install the driver and software files by following the instructions on the download pages Ensure that your system meets the requirements CD Software and Utilities 10 Front Panel Controls The monitor buttons are located on the bottom of the front panel Figure 4 1 Front panel control buttons IN E Y No Icon Description 1 Power Turns the monitor on or puts it in standby or sleep mode The Power button is located on the bottom or front of the monitor depending on the model 2 Menu Opens selects or exits the OSD menu 3 Navigates forward through the OSD menu and increases adjustment levels 4 Navigates backward through the OSD menu and decreases adjustment levels 5 Auto To utilize the auto adjustment feature press the key and release it immediately To use input source selection function press and hold the key for 3 seconds multi source models 11 Appendix 4 Operating the Monitor ENWW Using the On Screen Display OSD Luminance Con
26. ould be routed so that it is not likely to be walked on or pinched by items placed upon it or against it Particular attention should be paid to the plug electrical outlet and the point where the cord exits from the product 28 Japanese Power Cord Requirements For use in Japan use only the power cord received with this product A CAUTION Do not use the power cord received with this product on any other products Product Environmental Notices Materials Disposal This HP product contains mercury in the fluorescent lamp in the display LCD that might require special handling at end of life Disposal of this material can be regulated because of environmental considerations For disposal or recycling information contact the local authorities or the Electronic Industries Alliance EIA http www eiae org Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling or waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about wh
27. rotected content Your computer graphics card and monitor must both support HDCP to display protected content Connecting the Power Cable 1 Follow all Electrical and Power Warnings A WARNING To reduce the risk of electric shock or damage to your equipment Do not disable the power cord grounding plug The grounding plug is an important safety feature Plug the power cord into a grounded earthed electrical outlet Be sure that the grounded power outlet you plug the power cord into is easily accessible to the operator and located as close to the equipment as possible A power cord should be routed so that it is not likely to be walked on or pinched by items that are placed upon it or against it Do not place anything on power cords or cables Arrange them so that no one may accidentally step on or trip over them Do not pull on a cord or cable See Technical Specification Appendix B for additional information Figure 3 9 Connecting the power cable Pn A Ti woo qu ut Ihi Tau spun 2 Connect one end of the power cable to the monitor and the other end to a grounded electrical outlet A WARNING To prevent injury from electrical shock you should do one of the following if a properly grounded electrical outlet is not available 1 You should use an electrical outlet adapter that provides proper grounding 2 You should have a properly grounded electrica
28. the Monitor 1 Unpack the monitor Make sure all contents are included Store the packing box Turn off the computer and other attached devices 3 Prepare a flat area to assemble the monitor You may need a flat soft protected area for placing the monitor screen down while preparing it for installation Installing the Monitor You can install the monitor on a desktop or wall mount it Place the monitor in a convenient well ventilated location near your computer Connect the monitor cables after you have installed the monitor Preparing the monitor for desktop use 1 Set the monitor screen face down on a flat soft protected table or desk surface with the support column overhanging the edge A CAUTION The screen is fragile Avoid touching or applying pressure to the LCD screen doing so can cause damage 2 Press the column onto the monitor support column until it locks in place Figure 3 1 Attaching the Monitor Column 4 Chapter 3 Setting Up the Monitor ENWW 3 Press the base into the column until it locks in position Figure 3 2 Attaching the Base 4 Lift the monitor to an upright position and place on a flat stable surface Figure 3 3 Monitor in upright position Preparing the monitor for wall mounting 1 Check the stability of the wall mounting fixture A WARNING To reduce the risk of personal injury or of damage to the equipment check that the wall mounting fixture is adequately installed and sec
29. trast Brightness Eco Mode DCR 50 50 4 Standard gt 4 ON b Main Menu Item Main Menu Icon 1st Sub Menu Item 2nd Sub Menu Item Description Adjust Range Reset Value Luminance Contrast N A Contrast from Digital register Each step will increase decrease value by 1 0 100 Recall Warm Contrast Value Brightness N A Backlight Adjustment Each step will increase decrease value by 1 0 100 Recall Warm Brightness Value Eco Mode N A Picture Adjustment Brightness 90 Contrast 50 Brightness Contrast Adjustable Standard Brightness 20 Contrast 50 Brightness Contrast Grayed Text Brightness 40 Contrast 50 Brightness Contrast Grayed Internet Brightness 60 Contrast 50 Brightness Contrast Grayed Game Brightness 80 Contrast 50 Brightness Contrast Grayed Movie Brightness 100 Contrast 50 Brightness Contrast Grayed Sports Recall to Standard Mode DCR N A Dynamic contrast ratio On Off Recall Off Value ENWW Using the On Screen Display OSD 12 Image Setup Clock 7350 Phase lt 50 H Position 0 m 50 V Position 0 50 Image Ratio a Wide c Main Main 1st Sub 2nd Sub Adjust Menu Item Menu Icon Menu Item Menu Item Description Range Reset Value Image Clock
30. ured before attaching the monitor Refer to the instructions supplied with the wall mounting fixture and check that it is capable of supporting the monitor 2 Disconnect the power cable and any other cables from the monitor 3 Place the monitor face down on a flat protected surface 4 Adjust the stand to a proper angle and remove the screw hidden in the column cover that fasten the base to the monitor Figure 3 4 Location of screw securing base to monitor Installing the Monitor 5 5 Slide the base away from the bottom of the monitor Figure 3 5 Sliding the base away from the monitor 6 Remove the screws on the back of monitor Figure 3 6 Removing the screws from the back of the monitor 7 Four threaded holes are exposed These holes are for screws to attach the swing arm or other mounting fixture to the back of the monitor 8 Follow the instructions included with the mounting fixture to ensure that the monitor is safely attached The four threaded holes that are on the back of the panel are compliant with the VESA standard for mounting flat panel monitors 9 Attach a swing arm or other mounting fixture 6 Chapter 3 Setting Up the Monitor ENWW Connecting Monitor Cables Connecting the VGA Analog Cable or DVI D Digital Cable Use a VGA video cable or a DVI D cable to connect your monitor to your computer To use DVI you must have a DVI compliant graphic card Connectors are located on the back of the monitor
31. y for display size position clock and phase each time a new video mode is displayed For more precise adjustments of VGA input run the Auto Adjustment software on the CD If you want additional image quality improvement use the Clock and Phase controls of the monitor to fine tune the image See Optimizing Analog Video in this chapter Optimizing Analog Video Some monitors contain advanced circuitry that allow the monitor to function as a standard analog monitor Two controls in the OSD menu can be adjusted to improve analog image performance Clock Increase or decrease the value to minimize any vertical bars or stripes visible on the screen background Phase Increase or decrease the value to minimize video distortion or video jitter Use these controls only when the auto adjustment function does not provide a satisfactory monitor image in analog mode To obtain the best results 1 Allow the monitor to warm up for 30 minutes before adjusting 2 Access the OSD menu then select Image Setup 3 Set the main Clock settings correctly first because the Phase settings depend on the main Clock settings When adjusting the Clock and Phase values if the monitor images become distorted continue adjusting the values until the distortion disappears To restore the factory settings access the OSD menu select Factory Reset and then select Yes 17 Appendix 4 Operating the Monitor ENWW Power Saver Feature ENWW When the monitor
32. y the plug To reduce the risk of serious injury read the Safety and Comfort Guide It describes proper workstation setup posture and health and work habits for computer users and provides important electrical and mechanical safety information This guide is located on the Web at http www hp com ergo_and or on the documentation CD if one is included with the monitor A CAUTION For the protection of the monitor as well as the computer connect all power cords for the computer and its peripheral devices such as a monitor printer scanner to some form of surge protection device such as a power strip or Uninterruptible Power Supply UPS Not all power strips provide surge protection the power strips must be specifically labeled as having this ability Use a power strip whose manufacturer offers a Damage Replacement Policy so you can replace the equipment if surge protection fails Use the appropriate and correctly sized furniture designed to properly support your HP LCD monitor A WARNING LCD monitors that are inappropriately situated on dressers book cases shelves desks speakers chests or carts may fall over and cause personal injury Care should be taken to route all cords and cables connected to the LCD monitor so that they can not be pulled grabbed or tripped over Safety Precautions 2 e Use only a power source and connection compatible with this monitor as indicated on the label back plate of the monitor Be
Download Pdf Manuals
Related Search