Siig JJ-E20011-S1
Contents
1. FA CyberSerial Dual PCle U Quick Installation Guide Introducing the CyberSerial Dual PCle The CyberSerial Dual PCIe high speed serial I O card provides two additional 9 pin serial ports Features and Benefits e Compliant with PCI Express Base Specification 1 0a e PCI Express 1 lane x1 serial I O card works with PCI Express slots with different lane width e Installs into any available PCI Express slot and provides two 9 pin RS232 serial ports e 128 byte FIFO buffers dramatically increase data transmit receive speed and supports data rates up to 920 Kbps e Works as standard RS232 port or with 5V or 12V power output for devices that require power System Requirements e PCI Express enabled system with an available PCI Express slot e Windows 7 32 64 bit Vista 32 64 bit XP 32 64 bit Server 2003 amp 2008 32 64 bit 2000 Package Contents e CyberSerial Dual PCIe adapter and spare enhanced low profile bracket e Mini 2 port fan out cable e Y split power cable e Driver CD amp quick installation guide 04 0611A 1 Layout Power connector Fan out cable connector Figure 1 Layout Note If the serial port requires power output connect the system power source to board s power connector However most serial devices do not require additional power through the serial port Refer to your serial device s manual for more information Jumper Settings J1 J2 Short 2 3 no2. at steps 2 5 one or two times to complete the installation Windows 2000 1 5 6 At the Found New Hardware Wizard click Next Select Search for a suitable driver for my device recommended and click Next Check Specify a location uncheck the other boxes then click Next Insert the driver CD type in D 2K then click OK Change D to match your CD DVD ROM drive letter Click Next and Finish Repeat steps 1 5 to complete the installation To Verify Windows Installation 1 Check in Device Manager to verify successful driver installation For Windows 7 Right click Computer click Manage click Device Manager For Windows Vista Right click Computer click Manage click Continue click Device Manager For Windows 2000 XP Server 2003 Right click My Computer click Manage click Device Manager For Windows Server 2008 Right click Computer click Manage double click Diagnostics click Device Manager Click on the plus sign in front of Ports COM amp LPT CyberSerial 16C950 should be displayed two times Double click Multi port Serial adapters SIIG CyberPro 2S board should be displayed Changing COM Port Number Some serial devices need a specific COM port in order to work If your serial device works properly do not change this setting 1 From the Device Manager window double click Ports COM amp LPT then double click the CyberSerial serial port you want to change 2 C
3. be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio All centered around the distribution and switching of A V signals over CAT5 6 these products include matrix switches distribution amplifiers extenders converters splitters cabling and more SIG is the premier one stop source of upgrades and is committed to providing high quality products while keeping economical and competitive prices High quality control standards are evident by one of the lowest defective return rates in the industry Our products offer comprehensive user manuals user friendly features a
4. cord Connect the Mini 2 port fan out cable to the fan out cable connector on the card Driver Installation This section provides information on how to install the CyberSerial Dual PCIe drivers Windows 7 32 64 bit 1 Right click Computer click Manage click Device Manager Insert the driver CD Note Close the CD AutoPlay box if prompted Right click PCI Device click Update Driver Software Click Browse my computer for driver software Type D then click Next Change D to match your CD DVD ROM drive letter At Windows has successfully updated your driver software click Close 10 Under Other Devices starting at the top right click 16C95X Serial Port then click Update Driver Software Click Browse my computer for driver software Type D click Next Change D to match your CD DVD ROM drive letter At Windows has successfully updated your driver software click Close Repeat steps 6 9 to complete the installation Windows Vista 32 64 bit 1 ad a 6 At the Found New Hardware window click Locate and install driver software recommended then click Continue Click Don t search online Click I don t have the disc Show me other options Insert the driver CD click Browse my computer for driver software advanced Note Close the CD AutoPlay box if prompted For 32 bit Type D XP Later 32 bit then click Next Change D to match your CD ROM drive
5. jumper 0 volts Short 1 2 5V Short 3 4 12V Mini 2 port fan out cable Figure 2 Mini 2 port fan out cable Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the computer 3 Remove your computer s cover then remove the slot bracket cover from an available PCI Express slot Set J1 and J2 jumper settings to the desired voltage only if your serial device needs additional power from the serial port However most serial devices do not require additional power If power output is required connect the board s power connector to the system power supply For more information see Jumper Settings on page 2 To install the card carefully align the card s bus connector with the selected PCI Express slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket screw to secure the card Replace the computer cover and reconnect the power
6. letter For 64 bit Type D XP Later 64 bit then click Next Change D to match your CD ROM drive letter Click Close Repeat steps 2 5 to complete the installation Windows XP Server 2003 32 64 bit 1 Atthe Found New Hardware Wizard select No not this time click Next Select Install from a list or specific location Advanced then click Next Insert the driver CD check Include this location in the search uncheck the other box Note Click Cancel at the CD AutoPlay box if prompted For 32 bit Type D XP Later 32 bit and click Next then click Finish Change D to match your CD ROM drive letter For 64 bit Type D XP Later 64 bit and click Next click Continue Anyway then click Finish Change D to match your CD ROM drive letter Repeat steps 1 3 one or two times Click Yes to restart Winodows to complete the installation Server 2008 32 64 bit 1 q Atthe Found New Hardware window click Locate and install driver software recommended Click Don t search online Click I don t have the disc Show me other options Insert the driver CD click Browse my computer for driver software advanced For 32 bit Type D XP Later 32 bit then click Next Change D to match your CD ROM drive letter For 64 bit Type D XP Later 64 bit then click Next Change D to match your CD ROM drive letter At The software for this device has been successfully installed click Close Repe
7. lick Settings tab 3 Click the down arrow that is next to the COM Port number box select a COM port that is not in use then click OK 4 Click OK then close Device Manager to save the changes Blank Page Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You canalso submit questions online and a technical support analysts will promptly respond SUG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SUG RMA Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must
8. nd most products are backed by a lifetime warranty SIIG products can be found in many computer retail stores mail order catalogs and e commerce sites in the Americas as well as through major distributors system integrators and VARs PRODUCT NAME CyberSerial Dual PCIe FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCCCOMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 CyberSerial Dual PCleisa trademark of SHG Inc SUG and the SHG logo are registered trademarks of SIG Inc Microsoft and Windowsare registered trademarks of Microsoft Corporation Othernames used in this publication are for identification only and may be trademarks of their respective owners November 2009 Copyright 2009 by SIIG Inc All rights reserved
Download Pdf Manuals
Related Search