Siig SC-UNS012
Contents
1. 04 0268B 1 Serial ATA interface e Compliant with Serial ATA 1 0 specification e Provides two independent Serial ATA channels built in 256 byte FIFOs per channel for faster data transfer e Breaks the 137GB barrier Supports hard drives larger than 137GB e Co exists with on board IDE controller e Flash BIOS for easy upgrade e Achieves burst data transfer rates up to 150MB sec e Works with various brands of Serial ATA hard disk drives Board Layout FireWire 1394a USB 2 0 FireWire 1394a USB 2 0 Serial ATA Figure 1 Board Layout System Requirements e Pentium or equivalent computer with an available PCI slot e Windows 98SE ME 2000 XP Package Contents 1 USB 2 0 FireWire SATA Combo board 1 Serial ATA cable 1 Serial ATA 15 pin power cable adapter 1 USB 2 0 driver diskette 1 Serial ATA driver diskette This quick installation guide Hardware Installation General instructions for installing the card are provided below since the design of computer cases and motherboards vary Refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges Turn OFF the power to your computer and any other connected peripheral devic2. art Run type in A setup206 exe then click OK 3 Choose Yes I want to restart my computer now then click Close Remove the driver diskette O 00S ION 10 11 12 13 14 15 16 gA Windows restarts At the Add New Hardware Wizard window click Next Choose Search for the best driver and click Next Uncheck all boxes and click Next Click Next and Finish At the Add New Hardware Wizard click Next Choose Search for the best driver and click Next Uncheck all boxes and click Next Click Next and Next again If prompted insert your Windows 98SE CD ROM and click OK Click Finish Repeat steps 8 11 two more times At the Add New Hardware Wizard click Next Choose Search for the best driver and click Next Insert the Serial ATA driver diskette Check Floppy disk drives uncheck the other boxes then click Next Click Next and Finish Remove the driver diskette and restart the computer to complete driver installation Windows ME Driver Installation if Boot up Windows At the Add New Hardware Wizard window click Cancel Note Click Cancel 4 times if a hard disk drive is attached Insert the USB 2 0 driver diskette Click Start Run type in A setup206 exe then click OK Choose Yes I want to restart my computer now then click Close Remove the driver diskette Windows restarts The Add New Hardware Wizard detects PCI standard PCI to PCI bridge choose Automatic Search for a better
3. driver click Next then click Finish When the Add New Hardware Wizard detects a 1394 Host Controller choose Automatic Search for a better driver click Next then click Finish 6 When the Add New Hardware Wizard detects a PCI Mass Storage Device insert the Serial ATA driver diskette choose Automatic Search for a better driver click Next then click Finish 7 Remove the driver diskette and click Yes to restart Windows to complete driver installation Windows 2000 Driver Installation 1 Boot up Windows At the Found New Hardware Wizard window click Cancel two times 2 Insert the USB 2 0 driver diskette Click Start Run type in A setup206 exe then click OK 3 Choose Yes I want to restart my computer now then click Close Remove the driver diskette 4 Windows restarts At the Found New Hardware Wizard click Next 5 Insert the Serial ATA driver diskette Choose Search for a suitable driver and click Next 6 Check Floppy disk drives uncheck the other boxes then click Next 7 Click Next 8 At the Digital Signature Not Found window click Yes Our driver has been thoroughly tested in Windows for stability This message appears because Microsoft has not tested this product through WHQL certification 9 Click Finish to complete driver installation Windows XP Driver Installation Important f the hard disk drive connected to your controller has a boot partition do not connect this drive until the c
4. es Unplug the computer s power cord Remove your computer s cover and install the card in an available PCI slot Push the board down firmly but gently until it is well seated Secure the card and replace the cover Figure 2 Inserting the PCI Board Connecting Serial ATA drives The USB 2 0 FireWire SATA Combo board supports up to two Serial ATA hard disk drives If you plan to use the second Serial ATA channel you will need to purchase another Serial ATA cable 1 Install hard disk drive s in chassis 2 Connect the Serial ATA hard disk drive to the system power supply using the Serial ATA power cable adapter 3 Connect one end of the Serial ATA cable to the hard disk drive 4 Attach the other end of the Serial ATA cable to the Serial ATA connector on the USB 2 0 FireWire SATA Combo board 5 Follow the same instructions when connecting a second hard drive Serial ATA cable Power cable adapter Figure 3 Hard disk drive connections Software Installation Throughout driver installation you may be prompted to insert your Windows Installation CD Some files on this CD are neccessary to complete the driver installation Please insert the CD when prompted and follow on screen instructions Windows 98SE Driver Installation 1 Boot up Windows At the Add New Hardware Wizard window click Cancel Note Click Cancel 6 times if a hard disk drive is attached 2 Insert the USB 2 0 driver diskette Click St
5. f USB 2 0 FireWire SATA Quick Installation Guide Q Introducing the USB 2 0 FireWire SATA Combo The USB 2 0 FireWire SATA Combo design adds USB 2 0 FireWire 1394a and Serial ATA interfaces to your system Key Features and Benefits USB 2 0 interface e Adds three external and one internal USB 2 0 ports e Compliant with USB specification rev 2 0 e Supports high speed 480 Mbps full speed 12 Mbps and low speed 1 5 Mbps data transfer modes for simultaneous operation of multiple USB 2 0 1 1 devices e Hot swapping feature allows you to connect disconnect devices without powering down your system e Works with a various type of USB devices including hubs removable drives digital cameras scanners CD RWs DVD ROMs PC video cameras printers CF SM MMC SD Memory Stick memory card readers and more Note USB 1 1 devices are limited to USB 1 1 speeds even when they are connected to USB 2 0 host adapter or USB 2 0 hubs FireWire 1394a interface e Adds two external and one internal FireWire 1394a ports e Compliant with IEEE 1394 1995 P1394a 2000 and OHCI 1 1 standards e Supports serial bus data transfer rates of 100 200 and 400 Mbps e Hot swapping feature allows you to connect disconnect devices without powering down your system e Works with various types of 1394 devices including DV camcorders cameras hard disk drives CD RWs DVD ROMs removable drives scanners and other audio video devices
6. ght click My Computer click Manage then click Device Manager Double click Universal Serial Bus controllers and the following options should be displayed in addition to others that may come with your system NEC PCI to USB Enhanced Host Controller NEC PCI to USB Open Host Controller NEC PCI to USB Open Host Controller USB 2 0 Root Hub Device USB Root Hub USB Root Hub Note With XP Service Pack 1 installed the USB entries are different from what is listed above but function normally 3 Double click 1394 Bus Controller or IEEE 1394 Bus host controllers option and an OHCI Compliant IEEE 1394 Host Controller should be displayed 4 Double click SCSI controllers or SCSI and RAID controllers Silicon Image SiI 3112 Controller should be displayed Bios Configuration The SATA BIOS will appear everytime your system starts up If the bios doesn t show please try your controller in another PCI slot During this Post process the bios will show up and indicate the devices hard disk drives attached to it Technical Support QUESTIONS SIIG s Online Support has the answers Simply visit our web site at www siig com and click SUPPORT Our online support database is updated daily with new drivers and solutions The answers to your problems could be just a few clicks away Return Merchandise Authorization RMA SIG warrants to the original buyer of the product that the hardware is free of defects i
7. may be trademarks of their respective companies January 2003 Copyright 2003 by SIIG Inc All rights reserved
8. n materials and workmanship for a period of one two or five years from the date of purchase If your product fails to be in good working order during the warranty period you may return it to SIIG for repair or replacement at SIIG s option To return the product you need to follow these steps Step 1 Contact SIIG s RMA Department To obtain an RMA number SIIG s RMA Department can be reached by phone at 510 413 5333 or fax at 510 657 5962 or email at service siig com In order to issue an RMA number the product serial number is required This number can be found on the side of the box and on the back of the product Step 2 Complete the RMA form e Fill out your Return Merchandise Authorization RMA form and include it in the package with the product e Properly pack the product for shipping All software cable s and other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package and on the accompanying RMA form SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton Step 3 Ship the Product You are responsible for the cost of shipping back to SHG at the following address SUG Inc RMA 6078 Stewart Ave Fremont CA 94538 SIIG will ship the repaired or replaced product via UPS Ground or US Mail at no cost to you UK Warrant
9. ontroller s driver has been completely installed in Windows XP Follow the instructions below to install the driver for the controller first then shut down your system and connect the hard disk drive The controller is ready for operation Note If you have have XP Service Pack 1 or later installed Windows will automatically detect and install the correct USB 2 0 driver for this board In this case complete steps 5 7 and skip the others to complete the driver installation K Boot up Windows At the Found New Hardware Wizard window click Cancel two times Insert the USB 2 0 driver diskette Click Start Run type in A setup206 exe then click OK Click Continue Anyway Our driver has been thoroughly tested in Windows for stability This message appears because Microsoft has not tested this product through WHQL certification Choose Yes I want to restart my computer now then click Close Remove the driver diskette Insert the Serial ATA driver diskette after Windows resumes At the Found New Hardware Wizard window choose Install the software automatically Recommended then click Next Click Continue Anyway and Finish Repeat steps 6 7 two more times to complete driver installation To verify successful driver installation I Check Device Manager to verify successful driver installation Windows 98SE ME From the main desktop right click My Computer click Properties then click Device Manager Windows 2000 XP Ri
10. y amp Support Information The 5 year warranty supplied with this product is offered by SIG Inc If you should happen to encounter any problems with this product please follow the procedures below 1 If it is within the first year of purchase please return product to the outlet you purchased from 2 If your product is between 2 and 5 years old from date of purchase please contact SIIG using the contact details below For UK Technical Support Telephone 44 0 1255 687503 Fax 44 0 1255 687501 Email support siig uk com Website http www siig uk com PRODUCT NAME MODEL NUMBER USB 2 0 FireWire SATA Combo CN2507 FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SUG Inc 6078 Stewart Ave Fremont CA 94538 3152 USB 2 0 FirewiretSATA Combo is a trademark of SIG Inc SHG and SHG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation Other names used in publication are for identification only and
Download Pdf Manuals
Related Search