Siig 4-Port Serial PCI Card
Contents
1. Next Insert the driver CD and click Other Locations Type in D 9x click OK then Finish Change D to match your CD ROM drive letter From the Insert Disk window click OK When the Copying Files dialog box appears type in D 9x then click OK Restart Windows to complete the installation Windows 98 98SE iP en ee At the Add New Hardware Wizard window click Next Select Search for the best driver for your device Recommend then click Next Select Specify a location uncheck the other boxes insert the driver CD type in D 9x then click Next Change D to match your CD ROM drive letter Click Next then Finish Repeat steps 1 3 Click Next Next then Finish Restart Windows to complete the installation Windows ME 1 Atthe Add New Hardware Wizard choose Specify the location of the driver Advanced click Next 2 Check Specify a location uncheck the other box insert the driver CD type in D Me then click Next Change D to match your CD ROM drive letter 3 Click Next then Finish 4 Repeat steps 1 2 5 Click Next Next then Finish 6 Restart Windows to complete the installation To Verify Successful Installation In Windows 95 98 98SE ME 1 From the main desktop right click My Computer click Properties then click Device Manager Double click Ports COM amp LPT CyberSerial PCI 16Cxxx should be displayed four times Double click Multi function adapters SIIG CyberPro 4S2. PCI board and PCI Function should be displayed Windows NT 4 0 N O OT SDS From the desktop click Start then Run Insert the driver CD type in D NT4 Install_Serial exe then click OK Change D to match your CD ROM drive letter Click Next when the Welcome window appears Choose Install then click Next Click Yes then click Exit Restart Windows to complete the installation To Verify Successful Installation In Windows NT 4 0 1 Goto Start Setting Control Panel double click Ports device icon 2 Four new COM ports will be assigned when successfully installed Windows 2000 1 At the Found New Hardware Wizard click Next 2 Select Search for a suitable driver for my device recommended and click Next 3 Check Specify a location uncheck the other boxes and click Next 4 Insert the driver CD type in D 2000 then click OK Change D to match your CD ROM drive letter 5 Click Next and Finish 6 Repeat steps 1 5 two more times 7 Restart Windows to complete the installation Windows XP 1 Atthe Found New Hardware Wizard choose Install from a list or specific location Advanced then click Next 2 Insert the driver CD check Include this location in the search uncheck the other check box type in D XP and click Next Change D to match your CD ROM drive letter 3 At the Hardware Installation window click Continue Anyway then Finish Our driver has been tested for stability and co
3. CyberSerial POS 4000RJ lea o Quick Installation Guide Introducing the CyberSerial POS 4000RJ The CyberSerial POS 4000RJ is a high speed serial I O card that provides four additional serial ports Features and Benefits Conforms to PCI v2 2 Plug and Play Supports 32 64 bit 3 3V 5V PCI and PCI X slots Full support for Windows based software Reduces CPU load and improves system performance dramatically IRQ sharing feature reduces IRQ conflicts Provides four RJ45 high speed serial ports which can be individually configured as standard RS232 serial port or RS232 serial port with 5V 12V DC output Built in 32 byte FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment Enhanced bracket design to prevent bending Connected to PCB with washered screws for a more secure connection System Requirements Pentium or equivalent computer with an available 32 64 bit PCI or PCI X slot Windows 95 98 98SE ME NT 4 0 2000 XP Server 2003 04 0230C 1 Package Contents e CyberSerial POS 4000RJ board Driver CD e Quick Installation Guide Layout JP1 P3 P2 4 pin power connector optional Figure 1 Layout Note Make this connection only when two or more serial ports are configured for 5V 12V output Open 0 volts default Short 1 2 5V Short 2 3 12V Note Not all serial devices require additional power through the serial port Refer to your ser
4. all ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs and e commerce sites in the Americas and the UK as wellas through major distributors system integrators and VARs PRODUCT NAME CyberSerial POS 4000RJ FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Ave Fremont CA 94538 3152 CyberSerial POS 4000RJ is a trademark of SHG Inc SIIG and SIG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Pentium isa registered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies April 2005 Copyright 2005 by SHG Inc All rights reserved
5. ial device s manual for more information The jumpers can be removed if the ports do not need power Hardware Installation General instructions for installing the card are provided below Refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Pe Turn OFF the power to your computer and any other connected peripheral devices Unplug the power cord from the computer Remove your computer s cover Remove the slot bracket from an available PCI slot Change JP1 JP4 jumper settings to the desired voltage only if your serial device s needs additional power from the serial port For more information go to Figure 1 on page 2 Skip this step if power is not required To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket s holding screw to secure the card Replace the computer cover and reconnect the power cord Software Installation This section provides information on how to install the CyberSerial POS 4000R s drivers Windows 95 1 4 At the Update Device Driver Wizard window click
6. mpatibility 4 Repeat steps 1 3 five more times 5 Restart Windows to complete the installation Windows Server 2003 1 Atthe Found New Hardware Wizard choose Install from a list or specific location Advanced then click Next 2 Insert the driver CD check Include this location in the search uncheck the other check box type in D 2003 and click Next Change D to match your CD ROM drive letter 3 At the Hardware Installation window click Continue Anyway then Finish Our driver has been tested for stability and compatibility 4 Repeat steps 1 3 five more times 5 Restart Windows to complete the installation To Verify Successful Installation In Windows 2000 XP Server 2003 1 Rightclick My Computer click Manage then select Device Manager 2 Click on the plus sign in front of Ports Com amp LPT CyberSerial PCI 16Cxxx should be displayed four times 3 Double click Multifunction adapters SIIG CyberPro 4S PCI board should be displayed Changing COM Port Address Some serial devices need a specific COM port in order to work If your serial device works properly do not change this setting Windows 95 98 98SE ME 1 From the Device Manager window double click Ports COM amp LPT then double click the CyberSerial PCI serial port you want to change Click Settings tab click the down arrow that is next to the Port Name box and select a COM address that is not currently in use Click OK
7. st Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number will be issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping the product to SIIG at the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SHG Inc isa leading computer upgrade manufacturer of I O connectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b Networking Sound Cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the over
8. then close Device Manager to save the changes Follow steps 1 3 again to change the other serial port s if needed Windows 2000 XP Server 2003 1 From the Device Manager window double click Ports COM amp LPT then double click the CyberSerial PCI serial port you want to change Click Settings tab and click Advanced Click the down arrow that is next to the COM Port number box and selecta COM port that is notin use Click OK Click OK then close Device Manager to save the changes Follow steps 1 4 again to change the other serial port s if needed Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our website at www siig com and click on Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away Youcanalso submit questions online and one of our technical support analysts will promptly respond A lifetime manufacturer warranty supplied with this product is offered by SIG Inc Please see SIIG website for more warranty details If you should happen to encounter any problems with this product please follow the procedures below If it is within the store s return policy period please return the product to the store where you purchased from If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA reque
Download Pdf Manuals
Related Search