Siig 3-port PCI FireWire 800 Card
Contents
1. 512MB for Vista and 5GB or more available hard disk drive space Package Contents e FireWire 800 32 bit PCI board e Spare Low Profile bracket for Low Profile chassis e 1394a 6 pin to 4 pin DV cable e Ulead VideoStudio DV editing software e Driver CD e Quick Installation Guide Board Layout 4 Pin Power Connector a g Firewire Port A 1394a Firewire 800 Ports Figure 1 Board Layout Hardware Installation Note For Low Profile systems replace the currently mounted bracket with with the included Low Profile bracket General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices Unplug the computer s power cord 2 Remove your computer cover and install the card in an available PCI slot 5 Push the board down firmly but gently until it is well seated Connect an available 4 pin power connector from the system power supply to the 4 pin power connector on the FireWire 800 32 bit PCI board See Figure 1 onpage3 This connectio2. gt FireWire 800 DV Kit Z Quick Installation Guide Introducing the FireWire 800 DV Kit The FireWire 800 DV Kit is designed to add FireWire 800 1394b and 1394a 6 pin interfaces to your computer For your convenience one FireWire 1394a 6 pin 4 pin DV cable is included for connecting DV camcorders and other 1394 devices using 4 pin connector Ulead VideoStudio video editing software is also included for producing greeting cards video e mails or home videos complete with attractive titles effects and background music Features and Benefits e Provides 2 FireWire 800 1394b ports and 1 1394a 6 pin port for multiple 1394b 1394a device connections e Supports data transfer rates of 100 200 400 and 800Mbps e _ Built in 4 pin power connector provides extra power when connected to the system s power supply Recommended e Supports hot swapping and Plug n Play connection of peripheral devices e Includes one spare low profile bracket for systems with low profile chassis e Works with various types of FireWire 800 1394b and 1394a devices including portable hard disks DV camcorders digital cameras CD RW DVD ROM drives and other audio video devices 04 0460B 1 System Requirements e Pentium or equivalent PC with an available 32 bit or 64 bit PCI slot e Windows 2000 XP 32 64 bit Server 2003 32 64 bit Vista 32 64 bit For video capturing editing e Pentium 4 or equivalent PC e 256MB RAM
3. the FireWire 800 driver follow the same procedures but in step 3 instead of clickingon Microsoft1394 Drivers clickon Unibrain 1394 Drivers Connecting a DV Camcorder Before plugging in your DV camcorder verify that the Microsoft FireWire 400 driver has been successfully installed in your system see ubSwitch Utility on page 8 then follow the steps below 1 Connect the 4 pin connector of your FireWire 400 DV cable to your camcorder Connect the 6 pin connector of the DV cable to the FireWire 400 port Poweron the DV camcorder The camcorder should appear in Device Manager To Verify DV Camcorder Setup 1 Right click My Computer click Manage then click Device Manager Double click Imaging Device s Microsoft DV Camera and VCR or DV Camcorder should be displayed Connecting 1394 Devices General driver installation steps are provided below Please review your device s user manual for more details Windows 2000 1 At the Found New Hardware Wizard click Next 2 Select Search for a suitable driver then click Next 3 Uncheck all check boxes then click Next 4 Click Next then click Finish Windows XP 1 At the Found New Hardware Wizard For XP w SP2 or later Select No not this time then click Next For XP w SP1 or earlier Go directly to step 2 2 Select Install the Software Automatically click Next 3 Click Continue Anyway Skip if not prompted 4 Click Finish to complete the insta
4. a DV Camcorder for details on how to properly install your DV camcorder 1 Insert the Ulead VideoStudio DV software CD Auto run should start automatically If not click Start Run type in X Autorun exe then click OK Replace X with the drive letter of your CD ROM Choose Install Ulead VideoStudio and follow on screen instructions to complete installation Note For instructions on how to use Ulead VideoStudio please refer to VStudio pdf file located in the Manual directory on the Ulead VideoStudio DV software CD ubSwitch Utility In order to use a DV camcorder with this controller Microsoft s FireWire 400 driver must be installed in the system We have supplied an easy to use utility that allows switching between Microsoft s driver and the FireWire 800 driver Before using this utility unplug all devices from the FireWire 800 PCI board 1 Click Start Programs Unibrain ubcore Tools then ubSwitch Right click the ubSwitch icon located in the system tray by the clock Click the 1394 adapter that you want to switch then click on Microsoft 1394 Drivers Note If your system has multiple 1394 adapters installed make sure that you click on the 1394 adapter that the camcorder will be plugged into Windows will display an information box when the driver is ready for use It may take a few seconds for this box to appear Wait for this box to appear then connect your DV camcorder Note To switch back to
5. d out of this controller install the FireWire 800 driver using the directions below I PN Pe ee Insert the driver CD Click Start in the Start Search box 32 bit Type D setup32 exe press Enter Change D to match your CD ROM drive letter 64 bit Type D setup64 exe press Enter Change D to match your CD ROM drive letter Click Allow At the Welcome screen click Next At the License Agreement screen click Yes At the Destination Location screen click Next Select Complete then click Next At the Select Program Folder screen click Next At the Windows Security box click Install three times then click Finish Select the restart Windows option then click Finish To Verify Windows Installation 1 Check Device Manger for proper installation For 2000 XP Server 2003 Right click My Computer click Manage then click Device Manager For Windows Vista Right click Computer click Manage click Continue click Device Manager Double click 1394 Bus host controllers Unibrain driver OHCI Compatible Board should be displayed Ulead VideoStudio Installation The FireWire 800 DV Kit includes Ulead VideoStudio digital video editing software for producing home videos complete with attractive titles transitions and sounds Before installing VideoStudio make sure your FireWire adapter and DV camcorder are properly installed and configured See the next two sections ubSwitch Utility and Connecting
6. e follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to wwwssiig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number will be issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package mustbe included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 11 About SIIG Inc Founded in1985 SNG Inc isa leading computer upgrade manufacturer of 1 O connectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly featu
7. e D to match your CD ROM drive letter At the Welcome screen click Next At the License Agreement screen click Yes At the Destination Location screen click Next Select Complete then click Next At the Select Program Folder screen click Next At the Software Installation screen click Continue Anyway then click Finish Select the restart Windows option then click Finish Windows Server 2003 Windows Server 2003 automatically installs it s built in FireWire 400 driver for the FireWire 800 32 bit PCI To get the full speed out of this controller install the FireWire 800 driver using the directions below 1 Insert the driver CD Click Start Run 32 bit Type D setup32 exe click OK Change D to match your CD ROM drive letter 64 bit Type D setup64 exe click OK Change D to match your CD ROM drive letter At the Welcome screen click Next At the License Agreement screen click Yes a oP Pe 9 At the Destination Location screen click Next Select Complete then click Next At the Select Program Folder screen click Next At the Security Alert box click Yes This step is for 32 bit operating system only At the Software Installation screen click Continue Anyway then click Finish Select the restart Windows option then click Finish Windows Vista Windows Vista operating system automatically installs it s built in FireWire 400 driver for the FireWire 800 32 bit PCI To get the full spee
8. ll rights reserved
9. llation Server 2003 1 At the Found New Hardware Wizard For 2003 w SP1 or later Select No not this time then click Next For 2003 no service pack installed Go directly to step 2 2 Select Install the Software Automatically click Next 3 AttheSecurity Alert box click Yes or the Hardware Installation box click Continue Anyway then click Finish to complete the installation Windows Vista Windows Vista will automatically detect and install the drivers for most FireWire devices However for devices that do not install automatically follow the steps below to complete the installation 1 Click Locate and install driver software 2 Click Continue to complete the installation 10 Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could bejust a few clicks away Youcanalso submit questions online and a technical support analysts will promptly respond SUG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period pleas
10. n is recommended for consistent power output from the FireWire port Secure the card and replace the cover Software Installation This section provides information on how to install the FireWire 800 32 bit PCI drivers Please follow the directions below for your operating system Windows 2000 Windows 2000 automatically installs it s built in FireWire 400 driver for the FireWire 800 32 bit PC To get the full speed out of this controller install the Firewire 800 driver using the directions below 1 eS eS ee BS Insert the driver CD Click Start then click Run Type D setup exe click OK Change D to match your CD ROM drive letter At the Welcome screen click Next At the License Agreement screen click Yes Typein your customer information then click Next At the Destination Location screen click Next Select Complete then click Next At the Select Program Folder screen click Next At the Digital Signature screen click Yes then click Finish Select the restart Windows option then click Finish Windows XP Windows XP automatically installs it s built in FireWire 400 driver for the FireWire 800 32 bit PCI To get the full speed out of this controller install the Firewire 800 driver using the directions below 1 eo ei 8 Insert the driver CD Click Start Run Type 32 bit Type D setup32 exe click OK Change D to match your CD ROM drive letter 64 bit Type D setup64 exe click OK Chang
11. res and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME FireWire 800 DV Kit FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SUG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA FireWire 800 DV Kit is a trademark of SIG Inc SIG and the SIIG logo are registered trademarks of SIG Inc Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporationin the United States and or other countries Pentiumisa registered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies January 2008 Copyright 2008 by SHG Inc A
Download Pdf Manuals
Related Search