OmniMount 5.0
Contents
1. KIT COMPONENTS amp HOW THEY WORK TOGETHER Step 1 Attaching the Ball Shaft to the Speaker H Ceiling or shelf mounting orienta tlon Now position the clamp assembly on the wall ceiling or shelf at the mounting location you have selected e Insert the ball shaft appropriate to f the mounting option you have selected refer to the mounting a eae options above anchors e Rotate the ball shaft several turns until it is fully threaded into the female insert on the speaker When you hit bottom back out the ball shaft approximately one S quarter turn see Fig E __ e Using the 7 16 11mm open wrench tighten STEP 3 the jam nut PREPARING THE MOUNTING SURFACE AND ATTACHING THE CAUTION DO NOT OVER TIGHTEN When the ball aed y sing the clamp plate as a template mark the two holes with a pencil shaft resists moderate rotational force and forms a solid joint with the speaker stop tightening Using the clamp plate as a template accurately mark the two hole locations with a pencil 5 0 Speaker Mount User s Guide and Installation Manual The ball shaft threads into the speaker The clamp assem bly Consists of the clamp plate and jaw It mounts to the wall ceiling or a shelf The clamp surrounds the ball The mounting angle may be adjusted by simply loosening the clamp assembly tension screw Remove the clamp plate before drilling holes2. Before You Start Read This Section Carefully To use the 5 0 Speaker Mount Kit your speaker must meet the following criteria Remove the clamp plate before drilling into your mounting surface CAUTION It may be necessary to check that the surface preparation and the fasteners will not interfere with electrical wiring plumbing etc behind the mounting surface wall ceiling Your OmniMount Speaker Mount is designed to be mounted on a variety of wall and ceiling constructions Please follow all safety precautions listed here before installing the Clamp and Jaw Assembly e This mount is intended for mini speakers that weigh HER eS Step 2 up to 5lbs 2 3kg and have a 6mm threaded insert k i age See illustration 5 Positioning the Clamp Assembly e This mount will only fit and securely mount speakers Lo await 21 with 6mm pre threaded inserts If you are unsure about aa the insert please contact the speaker manufacturer Wall mounting Orient the clamp assembly vertically the OmniMount Mounting Options logo should be facing toward Before you begin decide which mounting option and ball shaft are the ceiling the tension screw appropriate for your speaker head faces toward the floor see fig G or H Your speaker must have a factory installed 6mm threaded insert We have found that most of the factory inserts Tools Required The clamp assembly should be oriented so that the install
3. installation Do not use substitutes drill the two holes to the minimum 2 63 5mm depth ii 74A Ceiling or shelf mounting orientation The jaw and the tension screw will face in the opposite direction toward have adequate pullout strength to support the weight for e 7 16 11mm open wrench or small crescent wrench the wall see fig I or J the speaker in some cases If you have any questions e Phillips screwdriver medium size or electric drill with e Position the clamp assembly over the anchors Fig L regarding the use of the inserts in your speaker consult Phillips drive bit your dealer or contact the speaker manufacturer directly f e Wire cutters e Hammer Step 5 e Position the wire on the ball shaft Wrap one of the tie wraps ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE CLAMP ASSEMBLY e Pick up the vice grip pliers regular pliers or small crescents wrench and use one of these tools to assist in tightening the tension screw Tighten in Y turn increments until the speaker is firmly held in place e Insert the hex key into the tension screw head and tighten see Fig O e If the speaker angle must be changed do not attempt to move the speaker without first loosening the tension screw Reposition then tighten the tension screw further until the speaker is held firmly in place second tie wrap Caution Tightest is not always the best Over tightening fasten
4. ways other than those for which it had been designed and manufactured The Manufacturer Distributor Retail and their respective agents cannot be held responsible or liable for injuries or property damage direct indirect or consequential arising out of the use or inability to use this product safely and properly Note Every effort has been made to provide accurate and error free assembly and installation information Omnimount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions OMNIMOUNT SYSTEMS INC 8201 South 48 Street Phoenix AZ 85044 5355 Voice 480 829 8000 Fax 480 756 9000 Email hdqrs omnimount com Web www omnimount com Copyright 2002 Omnimount Systems Inc All rights reserved OmniMount products are covered hy patents issued and or pending OmniMount is a registered trademark of Omnimount Systems Inc OmniMount products are manufactured in the USA Printed In the USA Part 1001361 5 0 speaker mount kit Rev 11 02
5. ed for mounting are strong enough to safely support You will need at least these tools for the installation clamp plate and OmniMount logo face the same the speaker However some inserts located on the top 5 32 hex wrench supplied direction as the front of the speaker you are mounting bottom or sides of the speaker are designed to be used in e An electric drill pairs for attaching a U shaped bracket to the speaker e Drill bits 14 for drywall installation or 5 16 for When one of these two inserts is used alone it may not wood and masonry surfaces CAUTION Drilling holes into masonry or concrete material requires the use of a carbide tipped 5 16 8mm diameter masonry drill and or hammer drill Always wear eye protection Mounting Onto Solid Wood Insert a 5 16 8mm diameter drill bit not provided Set depth of drill at a minimum 2 63 5mm protruding from the end of your drill CAUTION It may be necessary to check that the surface preparation and the fasteners will not interfere with electrical wiring plumbing etc behind your mounting surface wall ceiling floor Ippa bap Ne E arr hg Center the drill on the marked hole locations and carefully Note Use the supplied screws and anchors Your 5 0 Mount is supplied with oversize surface mounting screws and anchors The generous size of these fasteners provides an extra margin of safety for your
6. ers can weaken the installation Make sure the connection is extremely solid and then stop tightening e If rotational adjustment of the mounted speaker is required the jam nut must first be loosened the speaker rotated and the jam nut tightened again Use the 7 16 11mm open wrench or a small adjustable crescent wrench for this procedure Caution If the speaker loses its position do not attempt to move the speaker without first loosening the tension screw Reposition then tighten the tension screw further until the speaker is held firmly in place Step 6 Securing the Speaker Wire to the Ball Shaft e You can help to enhance the appearance of the installation with the two small tie wraps that have been provided in your kit around both the ball shaft and wire Repeat this step for the e Loop the open end of the tie wrap into the slot in the other end Pull tie wrap closed Repeat this step for the second tie wrap e Using a small pair of wire cutters snip the extra lengths of the tie wrap off as close as possible to the wrap buckle CONGRATULATIONS YOUR INSTALLATION IS NOW COMPLETE Note The following is made in lieu of all warranties expressed or implied The Manufacturer s only obligation shall be to replace parts of this product proved to be defective within two years of the date of purchase We are aware that this mounting assembly may be used for purposes and in
Download Pdf Manuals
Related Search