OmniMount 20.0 W
Contents
1. and tighten the 12 coarse thread screws provided Fig L Use a Phillips screwdriver or a JOINING THE BALL SHAFT AND CLAMP ASSEMBLY Check that the clamp assembly is open enough to accept the ball Get the 5 32 4 mm hex wrench Now lift the speaker into position and pop the ball into the clamp assembly Set your chosen angle of adjustment While supporting the speaker insert the long end of the hex key and turn the hex tension screw clock wise to take up the slack in the clamp assembly but do not fully tighten The ball should be properly seated and the speaker should still move easily Fig N ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE CLAMP ASSEMBLY Orient and hold the speaker in its final fixed position CAUTION The weight of the speaker must be fully supported throughout the entire tightening process Do not allow the ball shaft to rest upon or push against the clamp assembly Two installers may be needed for this one to support the speaker while the other tightens the clamp assembly Insert the hex key into the tension screw head and tighten Fig O Pick up the vice grip pliers regular pliers or small crescents wrench and use one of these tools to assist in tightening the tension screw Tighten in 2 turn increments until the speaker is firmly held in place e NOTE To hold the speaker in position and prevent any slippa2. on the speaker Using the mounting plate as a template with a pencil mark the outline of the two slots on the surface of the speaker CAUTION Be careful not to drill or screw into a speaker where you could possibly damage internal components If there s a question about this check with your dealer or the manufacturer or you may choose to carefully remove the driver and check inside the speaker enclosure yourself Remove the mounting plate from the speaker where you had been using it as a template Insert the 3 32 drill Fig F bit provided so that 1 2 sticks out of the end of your drill e Position the drill bit 14 down from the far end of the slot but centered in the middle of the slot Drill the pilot hole straight down into speaker Repeat the procedure for the second slot location Fig F e Place mounting plate onto the speaker insert the 14 screws and tighten until the Fig G screws are firmly seated against the top of the mounting plate Do not overtighten Fig G e Using the 7 16 open wrench or small crescent wrench tighten the jam nut securely against the top of the mounting plate Fig H STEP 2 POSITIONING CLAMP ASSEMBLY Wall Mounting Position the clamp plate vertically the OmniMount Logo should be facing toward the ceiling the tension screw head faces towards the floor Fig I drill STEP 2 POSITIONING CLAMP ASSEMBLY Ceiling or Floo
3. Mounting Options OPTION Il OPTION Ill NOTE When no threaded inserts for mounting purposes have been provided by the speaker manu facturer a speaker can still be safely mounted on the wall or ceiling But you have to be sure that it is put together with materials strong enough to support its own weight with the 14 course thread screws provided Most compact speakers are made well You must affix the mounting plate to the ball shaft before enough and use adequate materials thick enough for Pee the mounting plate to the speaker Pick up the ball shaft and mounting plate Insert the threaded end of the ball shaft into the top of the mounting plate until it butts up against the bottom of the jam nut 20 0 Speaker Mount Installation Instructions mounting with an OmniMount assembly The 14 screws should not be used in Masonite thin panel wood or plastic Such materials will likely require different fastening hardware and methods and e Pick up the extra jam nut Position it so possible reinforcement to be mounted safely If your This mount is ONLY for speakers weighing up to 20Ibs 5 32 hex wrench supplied that the circular part of the nut faces the evaluation raises any questions about the speaker s 9 kg Drill bits 4 for drywall installation or 5 16 for wood and end of the ball shaft protruding from the bottom of the mounting plate construction or
4. all shaft and rotate it several turns until it is fully threaded into the threaded female insert on the speaker When you Determine which format is hit bottom back out the ball shaft one quarte i o R needed for your speaker OPTION I threads directly into the 3 8 16 factory installed threaded insert on the speaker Using the 9 16 open wrench or crescent wrench firmly tighten the jam nut but DO NOT OVER TIGHTEN When the ball shaft resists moderate rotatio force and forms a solid joint with the Pick up the extra jam nut Position it so that the circular part of the nut faces the end of the ball shaft protruding from the bottom OPTION II when mounting plate is necessary to access threaded of the mounting plate Thread the nut onto the shaft a few turns indents the ball shart athiches to the plate only until the top of the nut is even with the end of the ball shaft OPTION III wood speakers with no threaded inserts the ball shaft attaches to the mounting plate which is attached to speaker with Place the mounting plate on a flat surface and pull up on the ball speaker stop tightening shaft Screw the top jam nut down against the top of the screws mounting plate Fig E Ps 5 Far a i OPTION IV Place the speaker on a scratch proof surface Be careful to protect any exposed components from damage Position the mounting plate at the chosen location
5. ed for purposes and in ways other than those for which it had been designed and manufactured The Manufac turer Distributor Retail and their respective agents cannot be held responsible or liable for injuries or property damage direct indirect or consequential arising out of the use or inability to use this product safely and properly Note Every effort has been made to provide accurate and error free assembly and installation information Omnimount Systems disclaims liability for any difficulties arising from the interpreta tion of information contained in these instructions Omnimount Systems Inc 8201 South 48 Street Phoenix AZ 85044 5355 Voice 480 829 8000 Fax 480 756 9000 Email hdqrs omnimount com Web www omnimount com Copyright 2002 Omnimount Systems Inc All rights reserved OmniMount products are covered hy patents issued and or pending OmniMount is a registered trademark of Omnimount Systems Inc OmniMount products are manufactured in the USA Printed In the USA 20 0 speaker mount kit Rev 03 02
6. ge the clamp assembly must get a good bite into the ball and form a SOLID joint The clamp assembly needs to be tightened enough to lock and hold the speaker FIRMLY at the chosen angle When that point is reached no further tightening is necessary jam nut tightened again Use the 7 16 11mm open wrench or Caution Tightest is not always the best Over tightening fasteners can weaken the installation Make sure the connection is extremely solid and then stop tightening e If the speaker angle must be changed do not attempt to move the speaker without first loosening the tension screw Reposi tion then tighten the tension screw further until the speaker is held firmly in place e If rotational adjustment of the mounted speaker is required the jam nut must first be loosened the speaker rotated and the a small adjustable crescent wrench for this procedure Caution If the speaker loses its position do not attempt to move the speaker without first loosening the tension screw Reposition then tighten the tension screw further until the speaker is held firmly in place CONGRATULATIONS YOUR INSTALLATION IS NOW COMPLETE Note The following is made in lieu of all warranties expressed or implied The Manufacturer s only obligation shall be to replace parts of this product proved to be defective within two years of the date of purchase We are aware that this mounting assembly may be us
7. material strength contact your dealer Thread the nut onto the shaft a few turns only until the top of the e Your speaker must have one of the following means of masonry surfaces lan ie even witii the end of the ball shafi Fig j or the speaker manufacturer and ASK QUESTIONS securing the mount Place the mounting plate on a flat surface and pull up on the ball e A factory installed 3 8 16 threaded insert Phillips screwdriver medium size shaft Screw the top jam nut down against the top of the mounting e 20 0 Wall Mount To mount on a wall the F Wire cutters Hammer An electric drill plate mounting plate will be affixed to the back of the PC HOEY tins tate CG COPEC SPACER INTERNEN MSETIS DOF use le Attach the mounting plate to the speaker by placing the slotted holes speaker If you are mounting on a side wall the with our mounting plate ll Ball Shaft Ceilin OmniMount over the threaded insertsand tightening the screws Fig D ere 20 0 Part List mounting plate will be affixed to the side of the e Sturdy wood frame that can be safely drilled into and Using the 9 16 open end wrench or small crescent wrench tighten ker The 20 0 sole bali shat Iso b d securely attached to our mounting plate with the 14 course the jam nut securely against the top of the mounting plate Peg me straig oe j all CANA SO sa a thread screws provided OPTION Ill for a ceiling application by affixing the mo
8. r Mounting The Wall Mount Ball Shaft may also be used to mount a speaker from the ceiling For installation placement see Fig I 2 The clamp assembly should be positioned so that the clamp plate with the OmniMount logo faces in the same direction as the front of the speaker you are mounting The jaw and the tension screw will face in the Position the clamp assembly onto the wall ceiling or floor at the mounting location you ATTACHING CLAMP ASSEMBLY Using the clamp plate as a template mark the two holes with a pencil Remove the clamp plate before drilling into your mounting surface CAUTION It may be necessary to check that the surface prepara tion and the fasteners will not interfere with electrical wiring plumbing etc behind the mounting surface wall ceiling or floor Your OmniMount Speaker Mount is designed to be mounted on a variety of wall and ceiling constructions Please follow all safety precautions listed here before installing the Clamp and Jaw Assembly CAUTION Drilling holes into masonry or concrete material requires the use of a carbide tipped 5 16 8mm diameter masonry drill and or hammer drill Always wear eye protection Mounting Onto Solid Wood or Masonry Insert a 5 16 8mm diameter drill bit not provided Set depth of drill at a minimum 2 1 2 63 5mm protruding from the end of your STEP 3 ATTACHING CLAMP ASSEMBLY the anchors Insert
9. unting plate to the top of the speaker e 20 0 Ceiling Mount To mount to the ceiling the mounting plate will be affixed to the back of the speaker The 20 0 bent ball shaft can also be used for a wall application by affixing the mounting plate to the top or bottom of the speaker Before You Start Read This Section Carefully To use the 20 0 Speaker Mount Kit your speaker must meet ONE o the following criteria e 916 11mm open wrench or small crescent wrench CAUTION If you have any questions or concerns regarding the mounting of your speaker contact a professional installer or the auton i e You must affix the mounting plate to the ball shaft before attaching al imi the mounting plate to the speaker Hrm Wench KIT COMPONENTS AND THEIR USE n Pick up the ball shaft and mounting plate Insert the threaded end of the ball shaft into the top of the mounting plate until it butts up against the bottom of the jam nut speaker manufacturer as necessary The Clamp Assembly The clamp assembly consists of the clamp plate and jaw and attaches to ia FO u i your mounting surface wall a sean 12 a r Fermas ceiling etc The clamp assembly ental E provides the clamping action that surrounds the ball and locks in the fe a r chosen angle of adjustment fig A The Ball Shaft The ball shaft attaches to the speaker in the following ways Insert the b
Download Pdf Manuals
Related Search