ENCORE ENLGA-1320
Contents
1. e One 3 5 inch 1 44MB diskette drive e The following cables Port Type Media Max Distance 10BASE T Cat 3 4 or 5 UTP 100 meter 100 1000BASE T Cat 5 or 5e UTP__ 100 meter NOTE 1000BASE T signaling requires four twisted pairs of Category 5 balanced cabling as specified in ISO IEC 11801 1995 and ANSI EIA TIA 568 A 1995 and tested for additional performance using testing procedures defined in TIA EIA TSB95 2 Unpack and Inspect Caution Under ordinary circumstances this adapter card will not be affected by static charge as may be received through your body during handling of the unit In special circumstances where you may carry an extraordinarily high static charge it had better reduce the charge by touching a ground before handling the adapter card Open the shipping gift box and carefully remove all items Please check the following items e One Gigabit Ethernet PCI Adapter e One 3 5 drivers diskette e This user s Manual Note If any of the listed items are missing please contact your distributor or reseller Install the Adapter Turn off the computer Remove the computer s cover in accordance to its manual Insert the contact edge of the adapter card into the connector of any available PCI Bus master expansion slot Press the card firmly into the connector to PCI slot Please make sure that the card s contacts are fully seated in the PCI2. FCC Statement This device compiles with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures All Trademarks and trade names are the properties of their respective owners Copyright 2003 All right Reserved Document Version 2 0 1 Introduction Thanks for the purchasing of your new Gigabit Ethernet PCI adapter This document describes the Installation of network adapter This adapter supports 10BASE T 100BASE TX and 1000BASE T Ether
3. case of PC to turn it on Windows XP will prompt Ethernet Controller in Found New Hardware Wizard dialog box insert driver disk bundled with Gigabit Ethernet Network Adapter Select Install the software automatically and then click 5 lt NEXT gt button Windows XP will prompt Gigabit Ethernet Network Adapter in Hardware Installation dialog box click lt Continue Anyway gt button Windows XP will display The wizard has finished installing the software for Gigabit Ethernet Network Adapter Fiber Gigabit Ethernet Network Adapter in Found New Hardware Wizard dialog box click lt Finish gt to complete the installation Linux kernel 2 2 x 1 Compiling rtl8169 c gcc DMODULE Wall Wstrict prototypes O6 c rtl8169 c Move the object code rtl8169 0 to the directory lib modules 2 2 14 5 0 net cp rtl8169 0 lib modules 2 2 14 5 0 net Insert module to kernel insmod rtl8169 Check driver status dmesg The media can be forced to one of the 5 modes as follows The link speed and duplex mode can be forced in 5 modes Command insmod rtl8169 media SET_MEDIA Ex insmod rtl8169 media 0x04 will force link mode to be 100Mpbs Half duplex SET_MEDIA can be _10_Half 0x01 _10_Full 0x02 _100_Half 0x04 _100_Full 0x08 _1000_Full 0x10 Linux kernel 2 4 x 1 Compiling r8169 c using Makefile make lt NOTE gt Please remember to ASSIGN NEW_INCLUDE_PATH in Makefile accordin
4. complete driver installation 7 Novell Netware System 5 X 6 X Run NetWare Server System When the Server prompt appears load the NetWare Server Installation Utility gt LOAD NWCONFIG Select Driver options from the Installation Options menu Select Configure network drivers from the Driver Options menu Select Select a driver from the Additional Driver Actions menu Press lt Ins gt to install an unlisted driver and then press lt F3 gt to specify a different path Insert Driver Diskette in your PC s floppy drive and specify the path A NWServer Select Gigabit Ethernet Network Adapter from the Select a driver to install menu If necessary select Select Modify driver parameters and protocols menu 10 Follow instructions to complete driver installation 61NB 1325D 200 C
5. elect the connection type in the Gigabit Ethernet Network Adapter and click lt OK gt Follow the screen instructions and finish the rest of installation procedures Restart your computer Microsoft Windows 2000 Plug the adapter into the PCI slot Press the power button on the case of PC to turn it on Windows 2000 will prompt Welcome to the Found New Hardware Wizard in Found New Hardware Wizard dialog box click lt NEXT gt button Windows 2000 will prompt Ethernet Controller in Found New Hardware Wizard dialog box select Search for a suitable driver for my device and then click lt NEXT gt button Select Specify a location from Optional search locations of Found New Hardware Wizard dialog box then click lt NEXT gt button Insert driver disk bundled with Gigabit Ethernet Network Adapter Enter the driver pathname A then click the lt OK gt button from Found New Hardware Wizard dialog box Windows 2000 will display The wizard found a driver for the following device Ethernet Controller in Found New Hardware Wizard dialog box click lt NEXT gt button Windows 2000 will display Completing the Found New Hardware Wizard Gigabit Ethernet Network Adapter Windows has finished installing the software for this device in Found New Hardware Wizard dialog box click lt Finish gt to complete the installation Microsoft Windows XP Plug the adapter into the PCI slot Press the power button on the
6. g to linux kernel 2 Move r8169 0 to the directory lib modules lt kernel gt kernel drivers net 6 cp r8169 0 lib modules lt kernel gt kernel drivers net where lt kernel gt represents the kernel version say 2 4 18 3 in Red Hat 7 3 3 Insert module by insmod r8169 4 Check driver status dmesg 5 The media can be forced to one of the 5 modes as follows Cmd insmod r8169 media SET_MEDIA For example insmod r8169 media 0x04 will force PHY to operate in 100Mpbs Half duplex SET_MEDIA can be _10_Half 0x01 _10_Full 0x02 _100_Half 0x04 _100_Full 0x08 _1000_Full 0x10 Novell Netware System 4 X Update Netware Server to 4 2 If don t update to 4 2 use diskette update file MSM NLM ETHERTSM NLM Run NetWare Server System When the Server prompt appears load the NetWare Server Installation Utility gt LOAD INSTALL Select Driver options from the Installation Options menu Select Configure network drivers from the Driver Options menu Select Select a driver from the Additional Driver Actions menu Press lt Ins gt to install an unlisted driver and then press lt F3 gt to specify a different path Insert Driver Diskette in your PC s floppy drive and specify the path A NWServer Select Gigabit Ethernet Network Adapter from the Select a driver to install menu If necessary select Select Modify driver parameters and protocols menu Follow instructions to
7. iver pathname A then click the lt NEXT gt button from Add New Hardware Wizard dialog box Select your installed adapter Gigabit Ethernet Network Adapter then click the lt NEXT gt button from the dialog box To complete the process please follow the instructions on the screen Restart your computer Microsoft Windows ME Plug the adapter into the PCI slot Press the power button on the case of PC to turn it on Windows ME will prompt PCI Ethernet Controller in Add New Hardware Wizard dialog box insert driver disk bundled with Gigabit Ethernet Network Adapter Select Install the software automatically and then click lt NEXT gt button Windows ME will prompt Gigabit Ethernet Network Adapter in Add New Hardware Wizard dialog box click lt FINISH gt button to complete the installation Restart the computer Microsoft Windows NT 4 0 he My Computers icon double click the Control nel icon he Control Panel icon group double click the Network icon In the Network Settings dialog box select the Adapter Tab then click Add button There will be a list of network adapters Click Have Disk for selecting one network adapter Insert this driver disk in drive A enter drive and pathname A Winnt4 then click the lt OK gt button You will see that the Gigabit Ethernet Network Adapter string appears in the Select OEM Option dialog box and click the lt OK gt button S
8. net copper interface Moreover the PCI interface on the Gigabit Ethernet NIC complies with PCI Local Bus is compatible with 32 bit PCI bus As a bus master the NIC requests access to the PCI bus instead of waiting to be polled 1 1 Features The Gigabit Ethernet PCI adapter is a cost effective high performance network interface card It operates in 10BASE T 100BASE TX and 1000BASE T modes and integrates easily with Fast Ethernet hub and Gigabit hub and switch Complies with IEEE 802 3 10BASE T standard Complies with IEEE 802 3u 100BASE TX standard Complies with IEEE 802 3ab 1000BASE T standard Complies with PCI specifications Supports 32 bit bus master for high throughput and low CPU utilization Supports both half and full duplex operation Supports 10 100 1000Mbps auto sensing capability Supports Wake On LAN depend on model and user s motherboard function Rich diagnostic LED mounted on bracket for easily viewing and troubleshooting LED Function 10M Link Act _ Green Blinking Green 100M Link Act_ Green Blinking Green 1000M Link Act Green Blinking Green Plug and Play Installation Network drivers on the diskette for Windows 98SE NT4 0 2000 XP ME Netware 4 5 6 X and Linux driver FCC CE class B certification 1 2 System Requirements To use the adapter you need the following components e One 32 or 64 bit PCI master mode expansion slot that is compliant with PCI bus specifications
9. slot Install the bracket screw that secures the card to the Computer chassis Replace the computer s cover Connect the CAT3 or CAT5 UTP cable to the RJ 45 network connector Remove driver diskette from the PC diskette drive Turn on the computer If the BIOS section of your computer s boot program is Plug and Play compliant then at power up the BIOS will configure any newly installed adapter automatically Note Due to some Plug n Play BIOS programs problem it happens occasionally that a newly installed adapter is assigned an interrupt number that is already used by another device adapter In such a case the conflict of interrupt number will cause faults in the behavior of both devices Then it is necessary to run the CMOS Setup utility and manually assign a non conflict Interrupt Number 4 Driver Diskette The divers diskette contains all the popular operating system drivers Windows 98SE ME NT4 0 2000 XP Linux Netware 4 5 6 X 5 Software Installation Microsoft Windows 98SE Plug the adapter into the PCI slot Press the power button on the case of PC to turn it on Windows 98 will prompt PCI Ethernet Controller in Add New Hardware Wizard dialog box click lt NEXT gt button Select Search for the best driver for your device from Add New Hardware Wizard dialog box then click lt NEXT gt button Insert driver disk bundled with Gigabit Ethernet Network Adapter Enter the dr
Download Pdf Manuals
Related Search