Atdec TH-3060-SAU flat panel wall mount
Contents
1. Installation Instructions se telehook Fit two M8x45mm Locking screws Flat Screen Wall Mount Swing Arm 5 to 25 brackets behind lay Ad into brackets behind Display Adjust Tilt the Tilt angle of the Display Tighten two locking screws with the Long Washer 6mm Allen Key provided G Fix the Tilt angle of the Display Component Checklist Telehook Flat Screen Wall Mount Swing Arm IMPORTANT supports a maximum Ensure you have received all parts against the component checklist prior to installing weight of 65kgs 143lbs NOTE ail i eee OL The manufacturer does Wall Mount Bracket Right Clinch Nuts q not aktapi responsibility Slider x2 ah for incorrect installation Tighten WARNING Do not attempt to adjust tilt angle without firstly loosening locking screws Doing so may damage product SS CS eee Wall Mount o gt oJ Wall Mount Bracket Lett Cover fo 0 TOOLS REQUIRED CA S e Power Drill Pivot Head e 12mm 1 2 Drill Bit Wall Mount Horizontal Bar e 7mm 9 32 Drill Bit e Adjustable wrench Bit Box Re z som E QB M10 Steel M10 Coach Wall Plug x4 M8 x45mm M8 Small M8 x45mm Washer x4 Screw x4 Locking Screws x2 Washer x2 Button Screws x2 Allen Key o o 1 Security Option For added security you may choose to attach a padlock to one or both brackets to prevent theft of the display It is recommended that the padlock should have2. a shackle diameter of 5mm 3 16 A ea EA 6 l M12 x80mm M12 Steel M12 Plastic M12 Cable Manager Multi Screw Washer Washer x2 Locking Nut Clip x4 Washer x6 C q mD m mD gm 8mm Long 6mm 5mm ME x lemn M x16mm M5 x16mm_ M4 xl mm Allen Key Allen Key Allen Key Mounting Mounting Mounting Mounting Screws x6 Screws x6 Screws x6 Screws x6 5mm 8 16 diameter shackle A Attach Telehook Swing Arm Unit to the Wall If necessary once the display is mounted adjust the horizontal Padlock angle as shown not supplied Masonry Wall Timber Stud Wall yw 1 2 hole 7mm 9 32 hole 7 M10 Coach Screw M10 Coach Screw A Tip Use a Spirit Level to ensure this surface is vertical Tip Use a Spirit Level to ensure this surface is atdec aan M10 Steel Washer ee No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 29 08 08 Attach Pivot Head to Swing Arm Step 1 Slide the Wall Mount Cover along the Swing Arm until it snap fits onto the wall plate Sn Wall Mount Cover Wall Plate Attaching the Brackets to the Display Step 1 p Attach left and right wall mount brackets to the rear of your display Select M4 M5 M6 or M8 mounting screws to suit your di
3. ets should rest on the horizontal bar with the slider between the bracket Note make sure the threaded nut faces inwards attached and hook the Brackets over the Sliders Step 2 Use the supplied Multi Washer as shown above Ensure that the tightest fiting hole in the washer is used for the specific sized screw Note distance X for use in the following steps
4. splay Step 2 Assemble the Pivot Head onto the Swing Arm as shown M12 Plastic Washer M12 Steel Washer 8mm Allen Key To M12 Screw ce M12 Locking Nut Ensure a minimum of two mounting screws are used per wall mount bracket Clinch nuts must be positioned as shown internally Clinch Nuts M8 Screw Hole M6 Screw Hole 5 Multi Washer M5 amp M4 Screw Hole D Positioning Sliders Step 1 Accurately position sliders at distance X as recorded in Section A Ensure the Sliders are equally spaced along the centre Horizontal Bar Screws x2 Distance X Horizontal Bar Attach the Horizontal Bar to Pivot Head Pivot Head 5mm Allen Key X wee i all M8x45mm 4 lt Button Screws Horizontal Bar 7 F Mounting the Display Step 1 Note This operation requires two persons Now that the horizontal bar is attached to the Swing Arm with the Sliders in place lift the Display with brackets Swing Arm Manager Clips Step 2 Secure slider in position and tighten firmly with supplied Allen Key Ensure that it locates into the slot on the horizontal bar The grub screw should tighten flush to surface Tighten Step 1 Attach the Horizontal Bar and tighten screws as shown Step 2 Attach the four Cable Manager Clips to the Swing Arm by inserting the clips into the holes Ensure that the clips are held firmly in place Note The brack
Download Pdf Manuals
Related Search