Whirlpool AKT 717
Contents
1. 90 396 safety requirements of EEC Directive Low voltage 73 23 protection requirements of EEC Directive EMC 89 336 requirements of EEC Directive 93 68 This hob is suitable for contact with foodstuffs and complies with EEC Directive 89 109 NOTES Improper use of the grids can result in damage to the hob surface Do not position the grids upside down or drag them across the hob e Ifthe hob has a glass ceramic top do not use Cast iron griddles or terracotta pots and pans Heat diffusers e g metallic mesh Two cookers for the same pot e Incase of prolonged use additional ventilation may be needed opening a window or increasing the extraction force of the hood e Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts Warning the protective rubber feet on the grids represent a chocking hazard for young children After removing the grids please ensure that all the feet are correctly fitted e Attention the glass lid if provided may shatter if overheated Before closing it make sure that all the burners are off After use make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER e This product can be embedded in a worktop 20 to 40 mm thick e If there is no oven beneath the hob insert a separator panel that has a surface at least equal to the open2. 7 3 00 214 g h 0 60 PETROLEUM GAS Semi rapid 67 1 65 118 g h 0 35 ap ay a3 Propane G31 Auxiliary 50 1 00 71 gh 0 30 Type of gas Configuration Rated thermal Total rated Air necessary m for the used model flow rate kW consumption combustion of m of gas G20 20 mbar 5 burners 10 8 1028 l h 9 52 G30 28 30 mbar 5 burners 10 8 785 g h 30 94 G31 37 mbar 5 burners 10 8 771 g h 23 80 ELECTRIC SUPPLY 230 V 50 Hz To get full satisfaction from the hob please read these instructions carefully and keep them for future consultation PRECAUTIONS AND GENERAL ADVICE To get full satisfaction from your hob please read these instructions carefully and keep them for future consultation e These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product description sheet and on the hob e Keep the packaging material plastic bags polystyrene parts etc out of the reach of children as they are potentially dangerous e Check whether the hob has been damaged during transport and remove any protective film from the appliance parts e This hob Class 3 is designed solely for household use for cooking food Any other use such as heating rooms is to be considered improper and as a consequence dangerous e Ensure that the installation and gas electrical connections are performed by a qualified technician in compliance with current local safety regulations e This appliance s
3. AKT717 Si s Removable panstand grids Auxiliary burner Semi rapid burner Rapid burner Semi rapid burner 4 ring burner Auxiliary burner control knob Semi rapid burner control knob Rapid burner control knob 0 Semi rapid burner control knob I 4 ring burner control knob SO 100 SOR Wa E P tial SYMBOLS Tap closed fA Maximum flame fi Minimum flame LIGHTING THE BURNERS To ignite one of the burners turn the relative knob anti clockwise to the maximum flame setting A 3 e Press the knob against the control panel to ignite the burner e After the burner has ignited keep the knob pressed for about 5 seconds to allow the thermocouple to warm up This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally because of sudden draught an interruption in the gas delivery boiling over of liquids etc The device must not be pressed for more than I5 sec If after that time has elapsed the burner does not remain lit wait at least one minute before trying to light it again The burner might go out when the knob is released This means that the thermocouple has not warmed up enough In this case repeat the operations described above PRATICAL ADVICE FOR USING THE BURNERS For better burner performance please stick to the following rules Burner Pot ee pots and pans that fit the burners see table on the 4 ring from 24 to 26 cm ight right Rap
4. e appliance must be ordered from After Sales Service e Adjust the minimum setting of the taps Note when liquid petroleum gas is used G30 G31 the minimum gas setting screw must be tightened as far as it will go Should you experience difficulty in turning the burners knobs please contact the After Sales Service for the replacement of the burner tap if found to be faulty REPLACING THE INJECTORS see the injector table in the Product Description Sheet e Remove grids A e Extract burners B e Using a socket spanner of the appropriate size unscrew the injector C e Replace it with the injector suitable for the new type of gas Before installing the hob remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted ae gc Ea a remove the knob and proceed as follows e tighten the screw to reduce the height of the flame e loosen the screw to increase the height of the flame The adjustment must be performed with the tap in minimum gas setting position small flame A e The primary air of the burners does not need to be adjusted e At this stage light up the burners and turn the knobs from max position A to minimum position to check flame stability Upon completion of adjustment reseal using sealing wax or an equi
5. e respective housings on the hob surface In the case of single grids make sure that they fit on the burner cap protuberance e Models equipped with electrical ignition plugs and safety thermocouples require thorough cleaning of the plug end in order to ensure correct operation Check these items frequently and if necessary clean them with a damp cloth Any baked on food should be removed with a toothpick or needle Note to avoid damaging the electric ignition device do not use it when the burners are not in their housing TROUBLESHOOTING GUIDE The hob may not work or work incorrectly Before calling the After Sales Service refer to the Troubleshooting Guide to determine the problem I The burner fails to ignite or the flame is not even Check that e The gas or electrical supplies are not shut off and especially that the gas supply tap is open e The gas cylinder liquid gas is not empty e The burner openings are not clogged e The plug end is not dirty All the burner parts have been positioned correctly e There are no draughts near the hob 2 The burner does not stay lit Check that e When lighting the burner the knob has been pressed for enough time to activate the protection device e The burner openings are not clogged near the thermocouple e The end of the thermocouple is not dirty e The minimum gas setting is correct see relevant paragraph 3 The containers are not stable Check that e The bottom o
6. ed by a qualified technician following the manufacturer s instructions and in compliance with current local safety regulations PROTECTING THE ENVIRONMENT I Packaging The packaging material is entirely recyclable and is marked with the recycling symbol which identifies it as a type of material that must be sent to local waste disposal centres 2 Product This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product qay i The symbol J on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Declaration of conformity CE e This hob has been designed constructed and marketed in compliance with safety requirements of EEC Directive Gas
7. f the container is perfectly flat e The container is centered on the burner e The grids have not been exchanged or positioned incorrectly If after the above checks the fault still occurs get in touch with the nearest After Sales Service AFTER SALES SERVICE Before calling the After Sales Service make sure you can give the following information type of fault or problem exact model written on the Product Description Sheet and Warranty service number that follows the word SERVICE on the rating plate under the hob and on the Warranty your complete address and phone number If any repairs are required please contact an authorised After Sales Service as indicated in the warranty Note Failure to comply with these instructions may compromise the safety and quality of the product SAAK 0000 000 00000 Manufacturer Whirlpool Europe S r l Viale G Borghi 27 21025 Comerio VA ITALY
8. hould only be installed and used in well ventilated rooms in accordance with current regulations Carefully read the instructions before installing and using this appliance e Gas adjustment and supply pressure are indicated on the rating plate located under the hob If the appliance is arranged for a type of gas different from that available refer to the paragraph Ajustment to different types of gas REFERENCE TO LOCAL REGULATIONS aD Regulation for room ventilation Note If the appliance is not equipped with safety devices on the burners thermocouples the air vents must be increased by 100 and must be at least 200 cm in compliance with M D 21 April 1993 Connection to gas supply Before connecting the appliance make sure that the gas supply system complies with standards UNI CIG 7129 and UNI CIG 7131 Gas connection The connection to the mains gas network or gas cylinder must be made using a rigid copper or steel pipe with fittings complying with standards UNI CIG 7129 or using a continuous surface stainless steel hose complying with standards UNI CIG 9891 The maximum length of the hose is 2 m Pressure control valves must comply with standards UNI CIG 7432 Es Gas installations for household cookers must comply with the REGULATIONS ON GAS INSTALLATIONS IN INHABITED BUILDINGS published in the B O E Official State Gazette No 77 of March 30 1974 Ensure that the installation and gas connections are perform
9. id from 24 to 26 cm Only use flat bottomed pots and pans i semi rapid from l6 to 22 cm Use the correct amount of water for cooking foods and keep the pot covered auxiliary from 8 to 14 cm In the case of pans with convex bottoms WOK use the support grille provided which should be positioned only on the 4 ring burner PRODUCT DESCRIPTION SHEET GB AT Es PT DIMENSIONS AND DISTANCES TO BE MAINTAINED mm NOTE If the distance A between the wall cabinets is between 600 mm and 730 mm the height B must be a minimum of 520 mm If the distance A between the wall cabinets is greater than the width of the cooktop the height B must be a minimum of 400 mm In case of installation of a hood above the cooktop please refer to the hood instructions for the correct distance INJECTOR TABLE CATEGORY II2H3 5019 319 5471 1 A Type of gas used Type of burner Injector Rated thermal Rated Reduced heat Gas pressure mbar marking flow rate kW consumption capacity kW F min rat max 4 ring 139 3 50 333 l h 1 50 NATURAL GAS Rapid 128 3 00 286 I h 0 60 17 20 25 Methane G20 Semi rapid 95 1 65 157 V h 0 35 Auxiliary 78 1 00 95 Wh 0 30 LIQUID 4 ring 95 3 50 254 g h 1 50 Rapid 87 3 00 218 g h 0 60 PETROLEUM GAS Semi rapid 67 165 120 g h 035 20 28 30 35 Butane G30 Auxiliary 50 1 00 73 g h 0 30 LIQUID 4 ring 95 3 50 250 g h 1 50 Rapid 8
10. ing in the work surface This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but in no case less than 20 mm from the bottom of the hob In the case that you intend to install an oven beneath the hob make sure that it is manufactured by Whirlpool and equipped with a cooling system The manufacturer declines all liability if another brand oven is installed beneath the hob e Before installation make sure that the local gas delivery conditions nature and pressure are compatible with the settings of the hob see the rating plate and injector table The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations Combustion products are discharged outdoors through specific hoods or wall and or window mounted electrical fans Continuous natural air circulation is ensured through a clear opening in a wall of at least 100 cm2 This wall opening must be a permanent and in a wall to the outside of the room to be vented b made in such a way that it cannot be obstructed from the inside or outside not even accidentally c protected by plastic grids metallic mesh etc taking care not to reduce the air vent effective area mentioned above d located near floor level and positioned so as not to interfere with the operation of the exhaust system INSTALLATION GAS CONNECTION e The gas supply system must comply with local regu
11. lations e You can find specific local regulations for some countries in the paragraph Reference to Local Regulations If no information concerning your Country is given please ask details to your Installer e The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations or by means of a continuous surface stainless steel hose complying with local regulations The maximum length of the hose is 2 linear metres e Before connecting the tube to the elbow fitting A interpose the washer B supplied in compliance with EN 549 Attention if a stainless steel hose is used it must be installed so as not to touch any mobile part of the furniture It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length e After connection to the gas supply check for leaks with soapy water ELECTRICAL CONNECTION e The electrical connections must comply with local regulations e The data relevant to the voltage and power absorption are indicated on the rating plate e The earthing of this appliance is compulsory by law Earth yellow green N The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements e When the hob is installed provide a single pole circuit breaker with a contact separa
12. tion of at least 3 mm If necessary the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer type H0O5V2V2 F T90 C or HOSRR F This operation must be performed by a qualified electrician ASSEMBLY After having cleaned the perimeter surface apply the supplied gasket to the hob as shown in the figure pN Top 40 mm Position the hob in the worktop opening made respecting eh the dimensions indicated in the Product Description i i AA SESE Sheet a re Note the power supply cable must be long enough to ss A Top 30 mm a permit its upward extraction A Metal hobs To secure the hob use the brackets A or B provided ah J with it Fit the brackets into the relevant bores shown by e d the arrow and fasten them by means of their screws in COP accordance with the thickness of the worktop see figures Top20 iie on the right ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and orange sticker applied on the top of the hob change the injectors Remove the orange sticker and keep it with the instructions booklet Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet e The gas nozzles must be changed by After Sales Service or a qualified technician e Nozzles not supplied with th
13. valent material CARE AND MAINTENANCE To maintain your hob in perfect conditions clean it after every use removing any food spills Before any cleaning operation disconnect the hob from the mains and wait for it to cool down CLEANING THE HOB SURFACE All the enamelled and glass parts should be cleaned with warm water and neutral solution e Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long Any food spills water sauce coffee etc should be wiped away before they dry Clean with warm water and neutral detergent and then dry with a soft cloth or chamois Remove baked on dirt with specific cleaners for stainless steel surfaces e Do not use abrasive or corrosive products chlorine based cleaners or pan scourers e Do not use vapour cleaning appliances e Do not use flammable products Do not leave acid or alkaline substances such as vinegar mustard salt sugar or lemon juice on the hob CLEANING THE HOB PARTS e Grids burner caps and burners can be removed to be cleaned e Clean them by hand with warm water and non abrasive detergent carefully removing any food residues and checking that none of the burner openings is clogged e Rinse and dry carefully e Refit burners and burner caps correctly in the respective housings e When replacing the grids make sure that the panstand area is aligned with the burner and that the burner feet are fitted in th
Download Pdf Manuals
Related Search