Samsung SyncMaster 2233RZ
Contents
1. 1 Turn off your monitor and unplug its power cord 2 Laythe LCD monitor face down on a flat surface with a cushion beneath it to protect the Screen 3 Remove the stand from the LCD monitor 4 Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm type base wall mount hanger or other base A e Do not use screws longer than the standard dimension as they may dam age the inside of the Monitor For wall mounts that do not comply with VESA standard screw specifica tions the length of the screws may differ depending on their specifications Do not use screws that do not comply with the VESA standard screw specifications Do not fasten the screws too tightly as this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents e Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions A o mount the monitor on a wall you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface Connections Contact the nearest Samsung Service Center for more information Sam sung Electronics will not be responsible for damages caused by using a base other than those specified Please use Wall Mount2. Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does request an a service for the main board of the computer If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution Q amp A Troubleshooting If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter in the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver Note If problems repeatedly occur contact an authorized service center Q How can change the frequency The frequency can be changed by reconfiguring the video card A Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Q How can adjusts the resolution Windows XP Set the resolution in the Control Panel Appearance and Themes Display Set tings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details Q How can I set the Power Saving function Windows XP Set the re
3. Safety Instructions Notational Power Note These safety instructions must be followed to ensure your safety and prevent property dam age Make sure to read the instructions carefully and use the product in the correct manner T Warning Caution Otherwise it may result in death or personal injury Otherwise it may result in personal injury or property damage O Notational Conventions Important to read and under Prohibited stand at all times Disconnect the plug from the outlet NU Do not disassemble Ground to prevent an electric shock eoo eae Do not touch 4 When not used for extended period of time set your computer to DPM If using screen saver set it to active screen mode The images here are for reference only and are not applicable in all cases or countries Shortcut to Anti Afterimage Instructions L3 Do not use a damaged power cord or plug or a damaged or JX Hika loose power outlet Bl o mi Otherwise this may result in electric shock or fire pa L3 Do not touch the power plug with wet hands when removing or Mr plugging the plug into the outlet R Otherwise this may result in electric shock L3 Make sure to connect the power cord to a grounded power out let Otherwise it may result in electric shock or personal injury Safety Instructions L3 Ensure that the power plug is plugged into the power outlet firmly and correctly Otherwise this ma
4. and click Next Seki the dice driver you viai Vo iba es thia handbag A Ta pa Sirahe ird eke pl pour Pain desc ans Pur Ctm Puma Pm Bar a iak faa PI a Mr Samsung ems Wr Sama eres ont haa subo Ad pied your deer sofware A BiTi meee Ti sunm it in pie Pai r Fin Te upto deve I nik Pos Tel dee liae dapa adi ha age faece audi tech Du fh pA muss Ir I Mone Type Menor Jaib Screen refresh raba 50 Hertz V pide modes that the monitor cannot display Clearing thi check box alpa yeu in select dapiry modes that this mont cannot display correctly This may leid te an unable T Thus i5 my mH maoritor Gat itend the desktop onto that montor Microsoft Windows XP Operating System Using the Software 1 Insert CD into the CD ROM drive 2 Click Start Control Panel then click the Appearance and Themes icon a gt Erter E inimene glue w emai Crit look E uper s a HET bon b Mokapad W Paint C Mindoro Podio Misayo HEH Explorer LOW menus Poesias Palo ber FE Rr crane cnm E 3 a domni T Eh EF Ben gore Le r LEE Pe Deu ars ae la ye Berma Dna namana k EE iy Biko e E Pere Passe ig Pep CREER ger m E wt 1 iz ch PIRE Ari Fae Et 2 mep and support Sasrch ET Bun Click Display icon and choose the Q d dS Ds Chan TT T append m b ikr rar cond bee ey E our aa F ie Nara oies
5. http www samsung com lat in http www samsung com lat in http www samsung com lat in http www samsung com lat in http www samsung com lat in http www samsung com lat in http www samsung com lat in http www samsung com at BELGIUM CZECH REPUBLIC 800 DENMARK EIRE FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL SLOVAKIA SPAIN SWEDEN SWITZERLAND U K ESTONIA LATVIA LITHUANIA KAZAKHSTAN KYRGYZSTAN RUSSIA TADJIKISTAN UKRAINE UZBEKISTAN Appendix Europe 02 201 2418 http www samsung com be SAMSUNG http www samsung com cz 800 726786 Distributor pro Ceskou republiku Samsung Zrt esk organiza n slo ka Oasis Florenc Sokolov ska394 17 180 00 Praha 8 8 SAMSUNG 7267864 0818 717 100 30 6227 515 http www samsung com fi 3260 dites SAMSUNG http www samsung com fr 0 15 Min http www samsung com dk http www samsung com ie 0825 08 65 65 0 15 Min 01805 SAMSUNG http www samsung de 7267864 0 14 Min 06 80 SAMSUNG 726 7864 http www samsung com hu 800 SAMSUNG 726 7864 02 261 03 710 http www samsung com lu 0900 SAMSUNG 7267864 http www samsung com nl 0 10 Min 3 SAMSUNG 7267864 Os 801 s 172678 http www samsung com it http www samsung com no 1SAMSUNG http www samsung com pl 022 607 93 33 808 20 7267864 0800 SAMSUNG
6. or pick a Control Panel icon 4 DE GeForce General Adapter Florator Eye mi Pag and Pisy Monitor Foro Im Donen aeteech nata ED Hautz 7 Hide micas that this morte cane cages Cheng thes Check bia alt qus Menara os Th s may kad bo an canas nam der cua damagod Ha 9 an CF MID TIE Cham ue meute ceu Et rab me NUE RE RESI Idus a a i biori io select display modes IF this cheplay DP lay Monitor Proper ties Genma Dirar 9 Dares Proves Chirr s Drake Duis fees cen Digtal Sigrar Bef Pack Drem LI Fe 6 Pag ard Play canton Hicroaolt GASO 512001 0 Micro mo H Pubilabror To came aiai alle Uus hia aa To lya thee chee Hos das dayi a If ihe deag lade alter upahan Hs dies poli Bk bo Iho giamh mbaba inie To uwemo Mec oies jjo Lok Ooa p TP amis pre al ain Beas Pasia cad Len ses Settings tab then click Advanced Grka pasy Higham 127 Ext EE 5 8 DONE CE cancer Flug asd Play Monitor Pio pee tbe ee Cie ps ad Coheed za Phag and Flag Monitor Devise bem Mera ees Mara solace headend maawat Ip Location on 3D Fiap Dime Pais Thus cheeses is tanab pinger nyay ann hasang problems path Iha dees chick Ticubleshoot l last han kwublsahookar Device usage Les iha dara raa Welcome to the Hardware Update Wizard Tiia vazad helpa pou natal solve bor Plug and Play Morac
7. 9 M pour hadassa come with an installation CD EE or Hope disk insert it nom hat do pou vani Hes wad bo do CO ect fee zolteeaner automatically Recorded LE mts bam a lest ca gpescihic locaton Povanced ck Mest lo continue Select Don t search will then click Next and then click Have disk Using the Software Hardware Update Wizard Fieste chocce ous poach and inolallaton nplsons C Besch bos the beat dered in Paas loc star hardware Update Wizard Galet the dovide chives pou wan ba install los this hondware a Soke the rra asctarer are radal of pour haka devis and Hen click Nasi H you Phase a dak that ponian the dresser you vent Ho lal cci Haee Duk Lise tha chak basa baka ka rni ca pard the ded slt teach vobach include cal pathi arrete meek T hes Deci dre lourd wal be natales reves gormpaibla Faederand M costed Af Pig and Page Honto 2 Dont readh yall chesse He drva ho ima Chose the option ko select the desce drea hom a bet Windows does mot guarentee hat Den creer posa chesney ba ha Beret match For your hides E That eirava tt deal igral Talma tre dre coming ii mportan Cie e C Click the Browse button then choose A D Driver and choose your monitor model in the model list and click the Next button Insta il From Disk Hardware Update Wizard Select the device diver you want bo insball For ihiz harden Incest the mul schurer s mstallahon dek and then a Taisi the Pamu del
8. 726 7864 http www samsung com sk 902 1 SAMSUNG 902 172 http www samsung com es 678 075 SAMSUNG 726 78 64 http www samsung com se 0848 SAMSUNG 7267864 http www samsung com ch CHF 0 08 min 0845 SAMSUNG 7267864 SAMSUNG http www samsung com pt http www samsung com uk CIS 800 7267 http www samsung ee 8000 7267 http www samsung com lv 8 800 77777 http www samsung lt 8 10 800 500 55 500 http www samsung com kz ru 00 800 500 55 500 8 800 555 55 55 8 10 800 500 55 500 8 800 502 0000 8 10 800 500 55 500 http www samsung ru http www samsung ua http www samsung com kz ru Terms AUSTRALIA CHINA INDIA INDONESIA JAPAN MALAYSIA NEW ZEALAND PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM SOUTH AFRICA TURKEY U A E Dot Pitch Vertical Frequency 1300 362 603 800 810 5858 Appendix Asia Pacific http www samsung com au http www samsung com cn 400 810 5858 010 6475 1880 HONG KONG 3698 4698 3030 8282 http www samsung com hk http www samsung com in 1800 110011 1 800 3000 8282 0800 112 8888 0120 327 527 1800 88 9999 http www samsung com id http www samsung com jp http www samsung com my 0800 SAMSUNG 0800 726 http www samsung com nz 786 1800 10 SAMSUNG 726 7864 http www samsung com ph 1800 SAMSUNG 726 7864 http www samsung com sg 1800 29 3232 http www samsung com th 02 689 3232
9. If the popup window to install the software for the main screen is not displayed proceed with the installation using the MultiScreen executable file on the CD 3 When the Installation Shield Wizard window appears click Next 4 Select agree to the terms of the license agreement to accept the terms of use 5 Choose a folder to install the MultiScreen program 6 Click Install 7 The Installation Status window appears 8 Click Finish 9 When the installation is complete the Multiscreen executable icon appears on your desktop Double click the icon to start the program Multiscreen execution icon may not appear depending on specification of computer system or monitor If that happens press F5 Key Installation Problems The installation of MultiScreen can be affected by such factors as the video card motherboard and the network environment oystem Requirements OS e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista It is recommended using MultiScreen in Windows 2000 or later Using the Software Hardware e 32 MB Memory above e 60 MB Hard disk space above Uninstall The Multiscreen program can be removed only by using the Add or Remove Programs option of the Windows Control Panel Perform the following steps remove Multiscreen Select Setting Control Panel on the Start menu and then double click Add Delete a pro gram Select Multiscreen from the li
10. by referring to the OSD The screen is out of focus or OSD cannot be adjusted Q A Have you adjusted the resolution or frequency on the monitor Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes LED is blinking but no images on the screen Q A Is the frequency properly adjusted when checking the Display Timing on the menu Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product There are only 16 colors shown on the screen The screen colors have changed after changing the vid Have the Windows colors been set properly Windows XP Set the resolution at the Control Panel Appearance and Themes Display Set tings Windows ME 2000 Set the resolution at the Control Panel Display Settings Has the video card been set properly Set the video card by referring to the video card manual There is a message that reads Unrecognized monitor Plug amp Play VESA DDC monitor found Q A Have you installed the monitor driver Install the monitor driver according to the Driver Installation Instructions See the video card manual to see if the Plug amp Play VESA DDC function can be Supported Install the monitor driver according to the Driver Installation Instructions Check the following items if there is trouble with the monitor
11. every 30 minutes Type 1 Type 1 FLGHT FLGHT TIME 02348 a My 20 30 UA102 21 10 UA102 Avoid using a combination of characters and background color with large difference in luminance Avoid using Grey colors which can cause Image retention easily e Avoid Colors with big difference in luminance Black 4 White Grey Ex SYSTEM 245 Information e Recommended settings Bright colors with little difference in luminance e Change the characters color and background color every 30 minutes Ex SYSTEM 245 SYSTEM 245 STATUS OK STATUS OK Every 30 minutes change the characters with movement Ex PAFAWUVAC Eo PLI UJ KA1710 12 00 KA1710 12 00 m FA 777 14 15 UA0110 13 30 LIAN11N 12 20 AA0002 14 00 FA7777 14 15 e The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it Image retention may not occur when a LCD panel is operated under normal con ditions Normal conditions are defined as continuously changing video patterns When the LCD panel is operated for a long time with a fixed pattern over 12 hours there may be slight difference in voltage between electrodes that work the liquid crystal LC in a pixel The voltage difference between electrodes increases with time forcing the liquid crystal to lean When this occurs the previous image may be seen when the pattern is changed To prevent
12. if there is any foreign material on the cloth make sure to shake it thoroughly before using it L3 When cleaning the product do not spray water directly onto the main body of the product Ensure that water does not enter the product and that it is not wet Otherwise this may result in electric shock fire or a malfunc tion L3 The product is a high voltage product Ensure that users do not disassemble repair or modify the product themselves Otherwise this may result in electric shock or fire If the product needs to be repaired contact a Service Center L3 If there is a strange smell or a strange sound or smoke is coming from the product disconnect the power plug immediately and con tact a Service Center Otherwise this may result in electric shock or fire L3 Do not place this product in a location exposed to moisture dust smoke water or in a car Otherwise this may result in electric shock or fire Safety Instructions f L3 When you drop the product or the case is broken turn the power ESS off and disconnect the power cord Contact a Service Center BA Otherwise this may result in electric shock or fire dd L3 If thunder or lightening is occurring do not touch the power cord ur or antenna cable ch y e 4 8 Otherwise this may result in electric shock or fire L3 Do not try to move the monitor by pulling only the wire or the 3 signal cable o a e Otherwise it may fal
13. login screen which can be seen A Ifthe initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your dealer Q Can you see Not Optimum Mode Recommended Mode 1680 x 1050 120 Hz on the screen A You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly A Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds SXGA or 75 Hz a Not Optimum Mode Recommended Mode 1680 x 1050 120 Hz message is displayed If the display exceeds 85 Hz the Troubleshooting display will work properly but the Not Optimum Mode Recommended Mode 1680 x 1050 120 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The message Is displayed again if the system is rebooted There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the button Then press any key on the keyboard again to activate
14. on Samsung Monitor homepage Click Update Driver in the Driver tab a eee SET ee Mg See rrr ire Manufacture iiir essor Kapa Locator en PACA Gere 6600 LE iaaa Comes Deno aan Fi aiana a iare prog Ta vem Gat nin oui Sa Sia ba To updsis Ea diam ppan Hor a naga fra drvca tah af dara e aver rd heck bo ak piy rale He Dianna Gus mecs dioa Tour Fa deser Ara Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers on my computer E X 1 a SS ia B I Hic dor viu van 20 sedqich dog dereer pee Bros for Creer uofrwang pn yr COSTI ay Paw deen carin anm s Plan moa Far panii dukatai des updabrd deer ferire Ko orale aud pee Boye Aa medi un eed Pos Ger LA fon eee igni dim der deletam Lgs np ed al eat test aa o Lan erap pal bom lips of dee db on ny ccengpurter Tika fied ard icm onc ard fern url aant oper ani Che abren r aral al cm uaga er ar ey gn wem dress a Click Have Disk and select the folder for example D Drive where the driver setup file is located and click OK Using the Software i mga Ha kha cone dies is gelecied baliw Specs the deve driver you ward 1m maba Rer thig handwanr wm CT Cancel Tani Pa aes IL Ld ILLE NL LII LB D dbz LLLI LEN I Ll Aa Gaman Fe Marin 9 Selectthe model that matches your monitor from the list of monitor models on the screen
15. the OSD e Off e On MENU gt gt MENU Display Time The menu will be automatically turned off if no adjustments are made for a certain time period You can set the amount of time the menu will wait before it is turned off e 5sec e 10sec e 20sec e 200 sec MENU a gt 5 MENU Adjusting the Monitor Reverts the product settings to factory defaults No Yes MENU gt 4 gt gt MENU Customized Key You can specify a function which will be activated when the Customized Key Ce is pressed MENU gt a gt wie t MENU Off Timer Adjusting the Monitor The monitors will turn off automatically at the specified time e Off On MENU gt 4 T gt a ri Sa T H Ga MENU Image Size You can change the size of the screen displayed on your monitor Auto e Wide e Auto The screen is displayed in accordance with the screen aspect ratio of the input signals e Wide A full screen is displayed regardless of the screen aspect ratio of the input signals ry Note e Signals not available in the standard mode table are not supported e Ifthe wide screen which is the optimal resolution for the monitor is set on your PC this function is not performed MENU gt a gt wie sa MENU 0 Information Shows a video source display mode on the OSD screen MENU a MENU Troublesho
16. your product for a long period of time put it into sleep mode or use a moving screen saver L3 Set a resolution and frequency appropriate to the product Otherwise your eyesight may be damaged Safety Instructions L3 If you continually move closer to the product screen your eye sight may be failing L3 To ease eye strain take at least a five minute break after every hour of using the monitor O Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations Otherwise it may fall and cause personal injury and or damage the product e Ifyou use the product in a location exposed to vibrations it may damage the product and result in fire L3 When moving the product turn the power off and disconnect the power plug antenna cable and all the cables connected to the product Otherwise it may result in electric shock or fire L3 Ensure that children do not hang onto the product or climb up onto the product e The product may fall and cause personal injury or death L3 If you do not use the product for a long period of time disconnect the power cord from the power outlet e Otherwise this may result in overheating or fire due to dust and may result in fire due to electric shock or leakage L3Do not place any heavy items or toys or confectionery such as cookies etc that may attract the attention of children and to the product e Your c
17. 0800 329 999 1 800 588 889 http www samsung com tw http www samsung com vn Middle East amp Africa 0860 SAMSUNG 726 7864 http www samsung com za 444 77 11 800 SAMSUNG 726 7864 8000 4726 Horizontal Frequency http www samsung com tr http www samsung com ae The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The dis tance between two dots of the same color is called the Dot Pitch Unit mm The screen must be redrawn several times per second in order to create and display an image for the user The fre quency of this repetition per second is called the Vertical Frequency or Refresh Rate Unit Hz Example If the same light repeats itself 60 times per sec ond this is regarded as 60 Hz The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle The inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Interlace and Non Interlace Methods Plug amp Play Resolution Correct Disposal Authority Appendix Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non Interlace method while showing odd lines and then even lines in turn is called the Interlace method The Non Interlace method is used for the majority of monitors to ensure a clear image The Inter lace method is the same as that used in T
18. Detachable Dimensions W x H x D Weight Simple Stand 516 8 x 372 7 x 71 2 mm 20 3 x 14 7 x 2 8 inch Without Stand 516 8 x 421 3 x 208 7 mm 20 3 x 16 6 x 8 2 inch With Stand 5 2 kg 11 5 Ibs VESA Mounting Interface 100 x 100 mm Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 Yo 80 Yo non condensing Specifications Environmental considerations Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system The interac tion of the monitor and the computer systems will provide the best operating conditions and monitor settings In most cases the monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above are used for this product But the pixels of RED GREEN BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen This is not from bad quality and you can use it without any problems For example the number of TFT LCD sub pixels contained in this product are 5 292 000 Note Design and specifications are subject to change without prior notice pa Class B Equipment Information Communication equipment for residential use This pro
19. E Picture Brightness Not available in MagicBright mode of Dynamic Contrast Adjusting the Monitor You can use the on screen menus to change the brightness according to personal prefer ence MENU gt MENU Contrast Not available in MagicBright mode of Dynamic Contrast You can use the on screen menus to change the contrast according to personal preference MENU 1 gt 53 MENU MagicBright Push the t button to circle through available preconfigured modes MagicBright is a new feature providing optimum viewing environment depending on the con tents of the image you are watching Currently seven different modes are available Cus Adjusting the Monitor tom Text Internet Game Sport Movie and Dynamic Contrast Each mode has its own pre configured brightness value You can easily select one of seven settings by simply pressing Customized Key control button Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the brightness and contrast by using the OSD menu Text For documents or works involving heavy text Internet For working with a mixture of images such as texts and graphics Game For watching motion pictures such as a game Sport For watching motion pictures such as a sport Movie For watching motion pict
20. If the screen is not normal change to a different mode lower mode of resolution colors or frequency Note If there is no Mode at All Display Modes select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide Linux Operating System To execute X Window you need to make the X86Config file which is a type of system setting file 1 Press Enter at the first and the second screen after executing the X86Config file 2 The third screen is for setting your mouse 3 Set a mouse for your computer 4 The next screen is for selecting a keyboard 5 Set a Keyboard for your computer 6 The next screen is for setting your monitor 7 First of all set a horizontal frequency for your monitor You can enter the frequency directly 8 Seta vertical frequency for your monitor You can enter the frequency directly 9 Enterthe model name of your monitor This information will not affect the actual execution of X Window Using the Software 10 You have finished setting up your monitor Execute X Window after setting other re quested hardware Natural Color Natural Color Software Program Natural Color Pro color management system Monitor Cal amp Profiling Preference Copright 2003 Samsung Electrenics Ca Ltd One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a d
21. Vs This is a function that provides the best quality screen for the user by allowing the computer and the monitor to ex change information automatically This monitor follows the international standard VESA DDC for the Plug amp Play func tion The number of horizontal and vertical dots used to compose the screen image is called the resolution This number shows the accuracy of the display A high resolution is good for performing multiple tasks as more image information can be shown on the screen Example If the resolution is 1680 x 1050 this means the screen is composed of 1680 horizontal dots horizontal res olution and 1050 vertical lines vertical resolution Correct Disposal of This Product Waste Electrical amp Electronic Equipment Europe only Applicable in the European Union and other Euro pean countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please sep arate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of ma terial resources Household users should contact either the retailer where they purchased this product or their local gov ernment office for details of where and how they can take this item for environme
22. according to the International standards Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver insert the CD ROM included with this monitor Driver installation is slightly different from one operating system to another Follow the directions appropriate for the oper ating system you have Prepare a blank disk and download the driver program file at the Internet web site shown here Internet web site http www samsung com Worldwide Installing the Monitor Driver Automatic 1 Insert CD into the CD ROM drive 2 Click Windows 3 Choose your monitor model in the model list then click the OK button un SAMSUNG monitor installer Select the display edapter on which you vert lo intel he monitor IL ROME ON 9220 Plug and Pine Morice Salad the motor which vou wemi bo install 4 Ifyou can see following message window then click the Continue Anyway button Then click OK button Microsoft Windows XP 2000 Operating System Hardware Installation EN The software you are installing for this hardware Samsung sasa has not passed Windows Logo besting bo wenky its compahkdiy wath Windows XP Tell me wiw the basing is important Continuing your installation of this software may impair or destabilize the comect operation of your system either immediately of in the future Microzolt strongly recommends that pou stop this installation now and contact the hardwa
23. ake sure that Au I the front end of the bottom of the product does not project out Q WHT Otherwise it may fall or cause personal injury e Use a cabinet or rack of a size appropriate to the product Safety Instructions L3 DO NOT PLACE CANDLES MOSQUITO REPELLANT CIG ARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT Otherwise this may result in fire L3 Keep heating appliances as far away from the power cord or the product as possible e Otherwise this may result in electric shock or fire L3 Do not install it in a badly ventilated location such as a bookcase or closet Otherwise this may result in fire due to an increase in the in ternal temperature L3 Put down the monitor carefully e Failing to do so may damage the monitor L3 Do not place the front of the product on the floor Otherwise this may result in damage to the screen display L3 Ensure that an authorized installation company installs the wall mount Otherwise it may fall and cause personal injury Make sure to install the specified wall mount L3 Install your product in a well ventilated location Ensure that there is a clearance of more than 10 cm from the wall Otherwise it may result in fire due to an increase in the internal temperature L3 Ensure that the packaging vinyl is kept away from children e Otherwise it may result in serious harm suffocation if children play with it L3 If the height of your moni
24. ates a highlighted menu item O Customized Ke yit d You can customize key assignment for the Custom button according to your preferences Note You can configure the customized key for a required function via Setup gt Customized Key O Power button ney Use this button for turning the product on and off 7 Power Indicator This light is lit when operating normally and blinks once when your ad justments are saved Note See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Rear Note The configuration at the back of the product may vary from product to product Introduction O POWER port Connect the power cord for your monitor to the POWER port on the back of the product Connect the DVI Cable to the DVI IN port on the back of your monitor Note DVI with HDCP HDCP operates only in Sin gle Link mode 60 Hz It is not supported in Dual Link mode Kensington Lock Cable holding ring Note Introduction The Kensington Lock is a device used to physically fix the system when using it in a public place The locking device has to be purchased separately The appearance and locking method may differ from the illustra tion depending on the manufacturer Refer to the manual provided with the Kensington Lock for proper use The loc
25. del and click the Next button then click Next button 10 Click the Finish button then the Close button If you can see the Digital Signature Not Found window then click the Yes button And click the Finish button then the Close button Microsoft Windows Millennium Operating System 1 Click Start Setting Control Panel 2 Double click the Display icon 3 Select the Settings tab and click Advanced Properties button Using the Software 4 Select the Monitor tab 5 Click the Change button in the Monitor Type area 6 Choose Specify the location of the driver 7 Choose Display a list of all the driver in a specific location then click Next button 8 Click the Have Disk button 9 Specify A D driver then click OK button 10 Select Show all devices and choose the monitor that corresponds to the one you con nected to your computer and click OK 11 Continue choosing Close button and OK button until you close the Display Properties dialogue box Microsoft Windows NT Operating System 1 Click Start Settings Control Panel and then double click Display icon 2 In Display Registration Information window click Settings Tab and then click All Display Modes 3 Selecta mode that you wish to use Resolution Number of colors and Vertical frequency and then click OK 4 Click Apply button if you see the screen working normally after clicking Test
26. duct complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas Class B equipment emits less electromagnetic waves than Class A equipment PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor to low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPM compliant video card installed in your computer Use the software utility installed on your computer to set up this feature State Normal Operation Power saving Power off Power button mode EPA ENERGY 2000 Power Indicator On Blinking Off Power Con 50 watts Less than 1 watts Less than 1 watts sumption This monitor is EPA ENERGY STAR compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality 0 As an ENERGY STAR Partner SAMSUNG has deter ENERGY STAR mined that this product meets the ENERGY STAR guidelines for energy efficiency Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if th
27. e signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjusts the screen as follows Display Mode Horizontal Vertical Fre Pixel Clock Sync Polarity Frequency quency Hz MHz H V KHz VESA 1680 X 1050 64 674 59 883 119 000 VESA 1680 X 1050 133 424 119 986 245 500 1680 X 1050 118 800 110 000 218 592 1680 X 1050 108 000 100 000 198 720 Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Hor izontal Cycle is called the Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called the Vertical Frequency or Refresh Rate Unit Hz Information For Better Display ka Adjust the computer resolution and screen injection rate refresh rate on the computer as described below to enjoy the best picture quality You can have an uneven picture quality on screen if the best picture quality is not provided for TFT LCD e Resolution 1680 x 1050 e Vertical frequency refresh rate 120 Hz e TFT LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm one millionth and above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem t
28. he monitor Troubleshooting Useful Tips A monitor recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1680 x 1050 120 Hz message comes up disconnect the cable from the computer while the monitor is still powered on If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble Check List Note Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistance please call the phone number on the In formation section or contact your dealer No images on the screen cannot turn on the monitor Q Is the power cord connected properly A Check the power cord connection and supply Q Can you see Check Signal Cable on the screen A Check the signal cable connection Connected using the DVI cable Press 4 button to have the monitor double check the input signal source Q Ifthe power is on reboot the computer to see the initial screen the
29. hildren may hang onto the product causing it to fall and this may result in personal injury or death L3 Do not turn the product upside down or move it while holding only the stand Otherwise it may fall and result in personal injury and or dam age to the product L3 Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater This may reduce the lifetime of the product and may result in fire L3 Do not drop any objects onto the product or cause any impact to the product Otherwise this may result in electric shock or fire Safety Instructions L3 Do not use a humidifier or kitchen table near the product e Otherwise this may result in electric shock or fire L3 When there is a gas leak do not touch the product or the power plug but ventilate immediately e Ifa spark occurs it may cause an explosion or fire L3 If the product has been turned on for a long time the display panel becomes hot Do not touch it Keep the small accessories in a location out of the reach of children L3 Be careful when adjusting the angle of the product or the height of the stand e This may result in personal injury as your hand or fingers may become caught e Also if you tilt the product too far it may fall and cause personal injury L3 Do not install the product in a location low enough for children to reach Otherwise it may fall and result in pers
30. ick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables Power Cord DVI Cable Introduction Others Cleaning Cloth Cable holding ring Note Cleaning Cloth is only provided for highly polished black products as a product feature Your Monitor Initial Settings The optimal resolution for this monitor is as follows Follow tne above settings to set the resolution Language Select the language using the up or down key The displayed content will disappear after 40 seconds Turn the Power button off and on It will be displayed again It can be displayed up to three 3 times Make sure to adjust the resolution of your PC before reaching the maximum count Note The resolution displayed on the screen is the optimal resolution for this product Adjust your PC resolution so that it is the same as the optimal resolution for this product Front SAMSUNG TVR Introduction MENU button MENU Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu O Brightness button Ki When OSD is not on the screen push the button to adjust brightness 2 Click here to see an animation clip Contrast W When OSD is not on the screen push the button to adjust Contrast gt gt Click here to see an animation clip 2 3 Adjust buttons k Y These buttons allow you to adjust items in the menu Enter button fe Activ
31. igital camera are not the same as those shown on the monitor The Natural Color S W is the very solution for this problem It is a color administration system developed by Samsung Electronics in association with Korea Elec tronics amp Telecommunications Research Institute ETRI This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images For more information refer to Help F1 in the software program How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD ROM Drive Then the initial screen of the program Natural Color will be executed Click Natural Color on the initial screen to install the Natural Color software To install the program manually insert the CD included with the Samsung monitor into the CD ROM Drive click the Start button of Windows and then select Run Enter D color INC ProSetup exe and then press the Enter key If the drive where the CD is inserted is not D enter the applicable drive How to delete the Natural Color software program Select Setting Control Panel on the Start menu and then double click Add Delete a pro gram Select Natural Color from the list and then click the Add Delete button Using the Software MultiScreen im MultiScreen Installation 1 Insert the installation CD into the CD ROM drive 2 Click the MultiScreen installation file Note
32. king device has to be purchased separately Note The location of the Kensington Lock may be different depending on its model Using the Anti Theft Kensington Lock 1 Insert the locking device into the Ken sington slot on the Monitor and turn it in the locking direction 2 Connect the Kensington Lock cable 3 Fix the Kensington Lock to a desk or a heavy stationary object Fix the cables using the holding ring as shown in the figure See Connecting Cables for further information regarding cable connections Connections Connecting Cables Rear of Monitor Rear of Computer Macintosh O Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet o9 Use a connection appropriate for your computer e Using the DVI Digital connector on the video card Connect the DVI Cable to the DVI IN Port on the back of your Monitor 2 2 Connected to a Macintosh Connect the monitor to the Macintosh computer using the DVI connection cable Note If the monitor and the computer are connected you can turn them on and use them Using the Stand Folding the base Connections Note You can tilt the monitor upwards at an angle of 1 to 20 1 0 Attaching a Base This monitor accepts a 100 mm x 100 mm VESA compliant mounting interface pad e Monitor Mounting interface pad Sold separately
33. l and result in electric shock damage to the product or fire due to damage to the cable L3 Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables Otherwise it may fall and result in electric shock damage to the product or fire due to damage to the cable L3 Make sure that the ventilating opening is not blocked by a table or curtain Otherwise it may result in fire due to an increase in the internal temperature L3 Do not place any containers containing water vases flower pots medicines as well as any metal on the product e If water or a foreign material enters the product disconnect the power cord and contact a Service Center e This may result in a product malfunction electric shock or fire L3 Do not use or keep combustible spray or flammable material near the product S3 MW PI X Otherwise this may result in an explosion or fire pl f L3Do not insert any metal such as chopsticks coins pins and steel or flammable objects such as matches or paper inside the 87 c Wy product through the ventilating openings input and output termi OL nals etc f water or foreign material enters the product disconnect the power cord and contact a Service Center Otherwise this may result in electric shock or fire L3 When using a fixed screen for a long time an afterimage or stain may occur Q s e If you are not using
34. maka of pour hadaa rence andi irn cle Hit P gni make sure thal the correct drive is selected below i have dak that conta Hue diei cni add bo ribal chek Hasse Desk Modd Samsung saa Copy manulachuner s fes Hom df This driver ix mot digitally signed Lel me veh crees Doro i mocrtant n Be J pers Com If you can see following message window then click the Continue Anyway button Then click OK button Hardware Installation The software pou are installing for this hardware Samsung sawa has nal passed werdet Logo be bo wany d compabkdiy wth inahas PP Tidi moo tres thes basing ts importan Continuing your inetallation of this software map impair or destabilize the corect operation of your system ether immediately of m the future Microsoft zbronagly commends thal pou stop this installation now and contact th hardware vendo for software that has passed Windows Logo testing Genius Anges Co Note This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Click the Close button then click OK button continually Hardware Update Wizard Completing the Hardware Update Wizard Tha vazard kar hraiherd ribalirsg the oiera fe E Samsung eee E Samsung sess Diwa Prosdaces Tampir Creaa Dabe 51422001 Dna Ves dcn 1 0 00 Hot gta egies Chigi 5 bgr Oro Do
35. ntally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase con tract This product should not be mixed with other commercial wastes for disposal Information in this document is subject to change without notice 2008 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Elec tronics Co Ltd is strictly forbidden Appendix Samsung Electronics Co Ltd shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this ma terial Samsung is the registered trademark of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of Video Electronics Standard Association the ENERGY STAR name and logo are registered trademarks of the U S Environmental Protection Agency EPA As an ENERGY STAR Partner Samsung Electronics Co Ltd has determined that this product meets the ENERGY STAR guidelines for energy efficiency All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners
36. o be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without any problems e For example the number of TFT LCD sub pixels contained in this product are 5 292 000 When cleaning the monitor and the panel outside please apply the recom mended small amount of cleaner by using a soft cloth to polish Do not force the LCD area but rub softly If excessive force is applied you may stain it ba If you are not satisfied with the picture quality you can get better quality of picture by performing the Auto Adjustment function in display screen that is ap peared as window termination button is pressed If there s still noise after the automatic adjustment use the Fine Coarse adjustment function e When viewing a fixed screen for an extended period of time a residual image or blurriness may appear Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time PRODUCT INFORMATION Image Retention Free LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention ta Warranty Warranty does not cover any damage caused by image retention Burn in is not covered by the warranty o What is Image retenti
37. on Information During normal operation of a LCD panel pixel image retention doesn t occur How ever if the same image is displayed for a long time a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal This may cause the liquid crystal to build up in a certain areas of the display Thus the previous image is retained when switching to a new video image All display products including LCD are subject to image retention This is not a product de fect Please follow the suggestions below to protect your LCD from image retention o Power Off Screen Saver or Power Save Mode Ex Turn the power off when using a stationary pattern Turn the power off for 4 hours after 20 hours in use Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible e Screen saver in one color or a moving image is recommended e Set the Monitor to power off with the PC Display Properties Power Scheme G3 Suggestions for specific applications Ex Airports Transit Stations Stock Markets Banks and Controlling Systems We recommend that you follow set up of your display system program as below D Display Information together with Logo or Moving image cycle Ex Cycle Display Information for 1 hour followed by a Display Logo or moving image for 1 minute 5 Change the Color Information periodically Use 2 different colors Ex Rotate the Color Information with 2 colors
38. onal injury e Since the front part of the product is heavy install the product on a level and stable surface L3 Do not put any heavy objects on the product his may result in personal injury and or damage to the prod uct When using the product use it in the correct posi tion Keep your back straight while looking at the prod uct he distance between your eyes and the screen should be between 45 to 50 cm Look at the screen from a slightly higher location than the height of the screen When using the product use it in the correct posi tion e Adjust the angle so that light is not reflected on the screen Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand Safety Instructions Keep your elbow at 90 degrees Keep your knees at greater than 90 degrees and keep your heels firmly on the floor Keep your arms lower than your heart Introduction Package Contents Note To use the 3D feature the program must be the 3D version and you must wear the 3D glasses provided by nVidia Since the graphics card video card must also support the 3D feature to enjoy 3D make sure to check if your graphics card is compatible by asking nVidia Note Please make sure the following items are included with your monitor If any items are missing contact your dealer Contact a local dealer to buy optional items Unpacking Monitor Manuals Qu
39. oting Self Test Feature Check E Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Mot Optimum Mode Recommended Mode X Hz Environment The location and the position of the monitor may influence the quality and other features of the monitor If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of t
40. re vendor for software that has passed Windows Logo testing STOP aan Using the Software Note This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Installing the Monitor Driver Manual Microsoft Windows Vista Operating System 1 Insert your Manual CD into your CD ROM drive 2 Click CD Start and Control Panel Then double click on Appearance and Personal ization 3 memme mm m mil mba ee oe EEN Sms E GP ee num eum ee ie um oan pee eri r rz gum m oes da Se oe rT i r m Ld 4 Dang or bre bo makeh piu Present I lupe Mini en AA Osce BNG LE elei rss Capas F 5 Click Properties in the Monitor tab If the Properties button is deactivated it means the configuration for your monitor is completed The monitor can be used as is Using the Software If the message Windows needs is displayed as shown in the figure below click Continue Meniier Type A Gran Pre Monitor BY Morvtor fe tinge Sen netnesh rate here z d pje F e Pal PA PC LOL aiy Ding Ei check ix i you 5c ad dispury sedem az Ha mart Cannot dapi crei y This mary leid 5a an urate Japar andir Gares orge p Note This monitor driver is under certifying MS logo and this installation doesn t damage your system The certified driver will be posted
41. solution in the Control Panel Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual A Windows ME 2000 Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual Q How can I clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor Note Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistance please call the phone number on the In formation section or contact your dealer Specifications General General Model Name SyncMaster 2233RZ LCD Panel Size 22 inch 55 cm Display area 473 76 mm H x 296 1 mm V Pixel Pitch 0 282 mm H x 0 282 mm V Synchronization Horizontal 30 135 kHz Vertical 56 75 Hz 120Hz Display Color 16 7 M Resolution Optimum resolution 1680x1050 120 Hz Maximum resolution 1680x1050 120 Hz Input Signal Terminated DVI Digital Visual Interface Compliant Digital RGB 75 Ox 10 Yo Maximum Pixel Clock 245 MHz Digital Power Supply AC 100 240 V 10 96 50 60 Hz 3 Hz Signal Cable DVI D to DVI D connector
42. st and then click the Add Delete button Adjusting the Monitor Direct Functions OSD Lock amp Unlock This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings Lock Hold down the MENU button for more than five 5 seconds to activate the OSD ad justment lock function Unlock Hold down the MENU button for more than five 5 seconds to deactivate the OSD adjustment lock function Note Though the OSD adjustment lock function is activated you can still adjust the brightness and contrast and adjust Customized Key Ct using the Direct button Customized key You can customize key assignment for the Custom button according to your preferences To view the operating screen displayed when pressing the rC button after configuring the customized key for a function click the name of each function MagicBright Image Size Note You can configure the customized key for a required function via Setup gt Customized Key Adjusting the Monitor Brightness When OSD is not on the screen push the Brightness button to adjust brightness Contrast When OSD is not on the screen push the Contrast P button to adjust Contrast OSD Function Brightness Contrast MagicBright Color Tone Color Con Gamma trol Sharpness Language Transparen Display cy Time Reset Customized Off Timer Image Size Key
43. ta Bol Back Driver Coes To vio chebadis about ho dira flow To unciae tus chester los thet device li tha dosa kada after updating then cles nodi bak bo ihe peek mababad hissi CEE Frith lo cbe the visit dl Tauminaali hee crever bihari ce Using the Software 10 Monitor driver installation is completed Microsoft Windows 2000 Operating System When you can see Digital Signature Not Found on your monitor follow these steps 1 Choose OK button on the Insert disk window 2 Click the Browse button on the File Needed window 3 Choose A D Driver then click the Open button and then click OK button How to install 1 Click Start Setting Control Panel 2 Double click the Display icon 3 Select the Settings tab and click Advanced Properties button 4 Choose Monitor Casel If the Properties button is inactive it means your monitor is properly configured Please stop installation Case2 If the Properties button is active click the Properties button then follow next steps continually 5 Click Driver and then click on Update Driver then click on the Next button 6 Choose Display a list of the known drivers for this device so that can choose a specific driver then click Next and then click Have disk 7 Click the Browse button then choose A D Driver 8 Click the Open button then click OK button 9 Choose your monitor mo
44. the monitor and restore the image on the screen Connected using the DVI cable You may get a blank screen if you boot the system before you connect the DVI cable or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system cannot see the On Screen Display Q A Have you locked the On Screen Display OSD Menu to prevent changes Unlock the OSD by pressing the MENU LL button for at least 5 seconds The screen shows strange colors or just black and white Q Is the screen displaying only one color as if looking at the screen through a cellophane paper Check the signal cable connection Make sure the video card is fully inserted in its slot Have the screen colors become strange after running a program or due to a crash between applications Reboot the computer Has the video card been set properly Set the video card by referring to the video card manual The screen suddenly has become unbalanced Q A Q A Have you changed the video card or the driver Adjust screen image position and size using the OSD Have you adjusted the resolution or frequency to the monitor Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes Q Troubleshooting The screen can be unbalanced due to the cycle of the video card signals Readjust Position
45. this the accumulated voltage difference must be decreased Information Common Electrode ITO Black Matrix Color F ilter Data Gate TFT Pixel Electrode Storage Capacitor Bus Line ITO Cs o Our LCD Monitor satisfies ISO13406 2 Pixel fault Class ll Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center U S A CANADA MEXICO ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP DOMINICA TRINIDAD amp TO BAGO VENEZUELA AUSTRIA North America 1 800 SAMSUNG 726 7864 http www samsung com us 1 800 SAMSUNG 726 7864 http www samsung com ca 01 800 SAMSUNG 726 7864 Latin America 0800 333 3733 0800 124 421 4004 0000 800 SAMSUNG 726 7864 01 8000112112 0 800 507 7267 1 800 10 7267 800 6225 1 800 299 0013 800 7919267 1 800 234 7267 00 1800 5077267 800 7267 1 800 682 3180 1 800 751 2676 1 800 SAMSUNG 726 7864 0 800 100 5303 Europe 0810 SAMSUNG 7267864 0 07 min http www samsung com mx http www samsung com ar http www samsung com br http www samsung com cl http www samsung com co http www samsung com lat in http www samsung com lat in http www samsung com lat In http www samsung com lat In http www samsung com lat in
46. tor is adjustable do not place any ob ject or part of your body on the stand when lowering it This may cause damage to the product or the person carrying it Clean When cleaning the monitor case or the surface of the TFT LCD screen A N wipe with a slightly moistened soft fabric L3 Do not spray cleaner directly onto the surface of the product DE uz e Otherwise this may result in the discoloration and distortion of 05 the structure and the screen surface may peel off Others Safety Instructions L3 Clean the product using a soft cloth with a monitor cleaner only If you must use a cleaner other than the monitor cleaner dilute it with water at a ratio of 1 10 L3 When cleaning the power plug pins or dusting the power outlet clean it with a dry cloth e Otherwise it may result in fire L3 When cleaning the product make sure to disconnect the power cord Otherwise it may result in electric shock or fire L3 When cleaning the product disconnect the power cord and clean it softly with a dry cloth e Do not use chemicals such as wax benzene alcohol thinner mosquito repellant lubricant or cleaner These may change the appearance of the product surface and peel off the indica tion labels on the product L3 Since the product housing is easily scratched make sure to use the specified cloth only e Use the specified cloth adding only a little water As the product may be scratched
47. ures such as a DVD or Video CD Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast MENU gt a T gt H Sa MENU Ce Color Not available in MagicBright mode of Dynamic Contrast Color Tone The tone of the color can be changed and one of four modes can be selected Cool Makes whites bluish Adjusting the Monitor Normal Keeps whites white e Warm Makes whites reddish Custom Select this mode when you want to adjust the image according to your prefer ences MENU gt 4 1 MENU Color Control Adjusts individual Red Green Blue color balance MENU gt a gt H sa OH sa 5 sa t MENU Gamma Gamma correction changes the luminance of the colors with intermediate luminance e Mode 1 e Mode 2 ex Mode 3 MENU gt a gt 5 sa MENU Adjusting the Monitor Image Sharpness Changes the clearance of image MENU a 25S amp MENU EI osp Language You can choose one of nine languages English Deutsch Espa ol Fran ais Italiano Svenska PyccKkHA Portugu s T rk e Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer MENU a 25S sa MENU Adjusting the Monitor Transparency Change the transparency of the background of
48. y result in fire L3 Do not forcefully bend or pull the power plug and do not place any heavy material on it e Otherwise this may result in fire L3 Do not connect multiple appliances to the same power outlet Otherwise this may cause fire due to overheating L3 Do not disconnect the power cord while using the product Otherwise this may result in damage to the product due to electric shock L3 To disconnect the apparatus from the mains the plug must be pulled out from the mains socket therefore the mains plug shall be readily operable This may cause electric shock or fire L3 Use only the power cord provided by our company Do not use the provided power cord of another product e Otherwise this may result in fire or electric shock Installation Be sure to contact an authorized Service Center when installing your N monitor in a location with heavy dust high or low temperatures high hu midity and exposed to chemical substances and where it operates for 24 hours such as at airports train stations etc Failure to do so may cause serious damage to your monitor L3 Do not drop the monitor when moving it This may cause damage to the product or the person carrying it MC O Ensure that at least two persons lift and move the product EE c yy Otherwise it may be dropped and cause personal injury and NW or damage the product _ L3 When installing the product in a cabinet or rack m
Download Pdf Manuals
Related Search