Newstar FPMA-D100BLACK
Contents
1. LCD Monitor Arm Parts Check List Code Component 01 Arm 02 Clamp 03 Cable Cover 04 Connector Plate 05 Rubber Cap Base Cover Clamp Pad Fitting Check List Code Description 08 Screw D 09 Bolt EN Caution Regular cleaning with a clean dry cloth is usually sufficient but for stubborn marks wipe over gently with a clean damp cloth Never use strong detergents or abrasive cleaners as these may damage the surface finish of your furniture There are many small components used in the construction of this unit These loose items should be kept away from young children while assembling your unit Before starting Assembly Please spend a short time reading this manual then follow the simple step by step guide to assembly Some panels are viewed differently from the exploded drawing below this is for extra clarity Do not discard any of the packaging until you have checked all the parts and the pack of fittings If you are missing any of the parts contact store where you purchased 7 04 06 R Tools Check List Allen Key NewStar user s Manual LCD Monitor Arm FPMA D100 computerproducts www NewStar nl Phone 31 0 23 547 88 88 Assembly Guide LN 09 x4 288 Clamping system is well assembled in standard packing However user could disassemble this unit and re assemble for thicker desk f2. The panel tilt range is from 90 90 Do not overwork to avoid the case to break Guarantee 6000 turns Don t repeat the operation continuously more than 10 times Movement distance of Arm The maximum radius is 410 mm 11 Safty Notes 1 Do not rotate the arm over the edge of desk to avoid the arm falls Fig 1 2 Do not place the arm in a shaking environment 3 Do not remove any part except handle rubber cap and bolt as illustrated Fig 2 4 Do not put your fingers in the space of knobs to avoid getting hurt Fig 3 5 Please maintain all operation under room temperature 6 Do not place the other stuff on the surface of the arm 7 Do not place the panel weighted over 8 kgs 8 Do not adjust the monitor with single hand Fig 4 9 Be sure to secure the arm to the panel with 4 screws tightly Fig 5 10 Be sure to adjust the arm in a vertical status after the job done to avoid the resiliency exhaustion of gas cylinder Fig 6 11 Cable cover is restricted to hold two 8mm amp
3. according to the instruction Panel weight Counterclockwise direction 4 kgs 4 turns 5 6 kgs 5 7 turns 7 8 kgs 8 10 turns A Standard Befestigungs System B Mounting on wall optional Clamp to the desk with at least 2 screws For Before assembling the arm to the wall make desks 15mm 102mm thick over 30mm is sure to remove the desktop clamp first suggested Hardware screws is not included C Track set System optional Before assembling the track to the arm make sure to remove the desktop clamp first The maximum of track cycle is 600 mm there are 24 stops The pitch between two stops is 25 mm Track is not included and if needed contact the store from which you purchased your product Net Weight 8 5 kgs Arm Operation rey The vertical adjustment range is from 10 90 Do not overwork to avoid the damage of gas spring system Guarantee 10000 turns Don t repeat the operation continuously more than 10 times The panel swivels is from 90 90 Do not overwork to avoid the case to break Guarantee 6000 turns Don t repeat the operation continuously more than 10 times Pitches between every two stops Mm The panel rotation range is from 135 135 Do not overwork to avoid the case to break Guarantee 6000 turns Don t repeat the operation continuously more than 10 times
4. itting by adjusting cranking bar amp clamp position At least two screws should be used for clamping system Remove pad cover and adhere to bottom of larger L bracket Suggested thickness of desk is 15mm 100mm over 30mm is ow 03 x8 Check your LCD panel first to find which VESA standard interface it supports before assembling 75 mm x 75 mm VESA standard interface Secure the arm to the rear of the LCD panel with screws 08 100 mm x 100 mm VESA standard interface Secure 100 x 100 mm plate 04 to the arm with screws 08 then secure the arm to the rear of the The loading weight of universal joint is initially fixed below 6 kgs Consult the store where you purchased about adjusting weight over 6 kgs Press two sides of 06 L lightly and remove 06 R 06 L outwards Let the cables run through the bottom of the arm and then press cable cover 03 to the arm to fix cables steady Assemble 06 L and 06 R back to arm after finish cable managing Remove the rubber cap 05 use the Allen key provided to adjust the weight capacity from 3 to 8 kgs The weight is originally set up at 3 kgs ADJUSTMENT Be sure to adjust the weight in a vertical position as illustrated Twist the Allen key in a clockwise direction for less weight counterclockwise direction more weight Make sure of the LCD panel weight prior to adjusting the weight
Download Pdf Manuals
Related Search