Newstar PLASMA-M1800
Contents
1. Installation Guide 1 Assembling the Mobile Stand 9 Left Pivot Arm Assembly Right Pivot Arm Assembly 2 Placing and Fixing the Plasma Unit A N Please refer to the documentation that comes with the plasma display unit to ensure that the correct size of screw is used A fe Installation Guide 2 Placing and Fixing the Plasma Unit Using the Block Part 18 Position and place the block along the groove provided in the package to fasten the Plasma on the Plasma Hook and tighten with the Hook onto the bottom mounting holes of the Truss Head Screw display unit Three 3 blocks to be used on each Plasma Hook if necessary Lift the display unit to the Cross Bar of the WallPlate and then lower the unit info place until the Hooks are fully seated in the groove ofthe U plate assembly AN To prevent interruption when placing the unit use cable ties to secure the power cord and signal cables behind the unit Check the viewing angle If the viewing angle is not in desired position adjust the Angle Adjustable Plate by loosening the Pivot Arm Assembly 12 Note2. Truss Head Screw M4X15 M4X20 M4X30 6pcs each M5X15 M5X20 M5X30 6pcs each M6X15 M6X20 M6X30 6pcs each M8X15 M8X495 6pcs each Part 12 Button Head Cap Screw Mola epcs Part 14 Washer Q4 4pcs 4 2pcs Part 16 Adjustable pad 4pcs 3 Co qu Part 18 Square Washer 6pcs Part 20 Spacer e 6pcs Package Contents Part 21 Spacer Il E Installation Guide 1 Assembling the Mobile Stand Zini 2pcs O8WASHER 2pcs SUPPORT ANGLE COVER tes Tope Installation Guide 1 Assembling the Mobile Stand _ dD4WASHER 25068 9 0 0 0 0 0 0 SLIDING PLATE Il 1pc O4WASHER Square Wosher DOS 8 Truss Head Screw 6pcs each Left Wall Plate and U Plate Assembly iset Right
3. Doconsult our qualified and authorized service technicians should you encounter any technical difficulties We are not liable for any damage or injury arising from any improper installation or mishandling Enjoy your plasma display unit
4. Installation Guide www newstar nl IVERSAL PLASMA LCD PLAY MOBILE STAND _ T 4 4 lar a ri V f W i W iva V 2 y b s cre n et Pisa sa ns zn m wa k all T Model PLASMA M1800 Important Notes Thank you for purchasing the Mobile Stand This Mobile Stand is feasible for most models of 42 and 50 wide plasma display units To ensure correct usage please read this instruction manual thoroughly Keep this manual for future reference BRACKETS SHOULD BE MOUNTED ONLY BY A QUALIFIED INSTALLER User will be responsible for any injuries and damages that may arise from improper installation and mishandling of Mobile Stand Ensure all mounting screws are appropriately positioned and properly tightened fastened Installers are to ensure customer s safety when installing We reserve the right to amend or undertake any necessary changes without prior notice N WARNING This symbol indicates the incorrect handling Ignoring this symbol can result in the possibility of personal injury or even death N CAUTION This symbol indicates the incorrect handling Ignoring this symbol can result in the possibility of personal injury and physical damage N This symbol indicates additional cautions including warnings N This symbol indicates forbidden actions n This symbol indicates required actions ERAN RO Caution Forbidden Required general gene
5. d smoke as tire could arise trom these SOUFCes Do not place on sloping surface Strictly install ona vertical surface only Lock the brake ot the wheels after position is decided side view Keep the room well ventilated to prevent room temperature rising and possibilities resulting in fire CAUTION Do not place in location where room temperature and humidity are excessively high To prevent tire avoid contact with water Do not apply unnecessary stress or load on the installed unit Do not place where there is direct sunlight or strong light to prevent eye fatigue when using the unit Package Contents 1 Angle Adjustable Plate and Hook Module Part 1 Part 2 Base plate and Wheel Assembly 1set Fixed Pole 1pcs Part 3 Castor Wheel Brake 2 pcs Part 4 Castor Wheel Swivel 2 pcs Wall Plate amp U Plate Assembly 1set VA Part 5 lt Y Part6 Left Pivot Arm Assembly 1set Right Pivot Arm Assembly 1set Part 7 Part8 Plasma Profile Assembly 1set Support Angle Cover 1pcs E Part 9 Part 10 Glass Plate Assembly 1set Sheiving Bracket 1pcs Package Contents Part 11 Rubber Support 2pcs D Part 13 Truss Head Screw M4X7 4pcs a Allan Wrench AS pc Q3 1pc Dire 1pc 5 1pc Part 19
6. ral general Parts Specifications Post Height 6ft 7ft Profile Module ft Profile Module 7ft Base Plate Module IN BA e i 98mm 3 4 5 WARNING Assembling without the use of bolts and screws at designated points may result in injury and damage to properties or the unit collapsing from its installed position Should a malfunction occur disconnect the power trom the main socket and surround the area with ropes to prevent others from getting near it Do not push the top of the Mobile Stand It is strongly recommended that the plasma is removed when shifting the Mobile Stand from one place to the other It is strongly recommended that two persons carry out the installation When adjusting angles or carrying out maintenance disconnect the power supply to avoid electrical shock CAUTION Do not remove any bolts and screws trom the Mobile Stand or do any changes to the Mobile Stand Do not install near an air conditioner Do not place at a place where there are excessive dust an
Download Pdf Manuals
Related Search