User Handbook
Contents
1. A Introduction NOILJINGOYLNI 8 ALNVHHVM The SignalLED Sign is a new elegant approach to illuminated displays and signage Using the latest technology and components the SignalLED sign can be simply configured onsite for colour and mode Choose from white green red blue yellow orange cyan and magenta Choose from a large range of different sign text Four illumination modes constant flashing pulsing and off Two control pull low inputs Single or twin signs with separate controls DC input power supply provided Flush mounted to the wall or end mounted Double sided end mounting available for use in corridors Simple to install Custom signs can be made to order Safety Information This equipment has been designed to meet the safety regulations currently advised in the country of purchase and it conforms to the safety regulations specified by use of CE the CE Mark This equipment operates in a horizontal position Handling Notes The SignalLED sign should be installed in an area which is not subject to excessive heat or cold Also you should avoid installing it in atmospheric conditions which are dusty smoky or dirty or where there is moisture or vibration The sign is for internal use only The unit is not sealed and cannot be used outside or in very damp or humid environments Do not use any solvents to clean the sign Use a soft dry brush or a clean cloth moistened with2. LD 40F2ONA MCL ON AIR MIC LIVE the sign off ui T solid red LD 40F2ONA SIL ONAIR SILENCE Turns the sign off E e EA E LD 40F2TX REH TX REH Turns the sign off solid blue 18 SONIFEX SignalLED User Handbook APPENDICES 5 SignalLED Preconfigurations continued inal Top Level Part Number Both Inputs LD 20F1MCL Turns the whole sign solid green when connected to 0V urns the sign off LD 20F10NA Turns the whole sign solid red when connected to 0V ise dien LD 20F1REC Turns the whole sign solid green when connected to 0V urns the sign off LD 40E1MCL Turns the whole sign solid green when connected to 0V LD 40E10NA Turns the whole sign solid red when connected to 0V urns the signoff LD 40E1REC Turns the whole sign solid green when connected to 0V ste gt v m 2 m LD 40F1ADB Turns the whole sign solid green when connected to 0V uris the sign oft LD 40F1DOR Turns the whole sign solid red when connected to 0V miss distincti Turns the whole sign solid red when connected to 0V LD 40F1EXIT urns the sign off LD 40F1INT Turns the whole sign solid green when connected to 0V wise desinet LD 40F1MCL Turns the whole sign solid green when connected to 0V urns the sign off LD 40F1MET Turns the whole sign solid green when connected to 0V wise dice deme LD 40F1NOE Turns the whole sign solid green when
3. so notify da of the detalle of the modifications for imora application for modificamos farm i ben Dia office M yoo have supplied a merpie of the produet for examination please arange to collect the sample thirty deys of the de of this letter 10 the semple bas mot bees cotiectad by this date It wil be of nocordunce with section Lf of the Electrical Sadety Regulation 2002 Yon are reminded that It la mandatory for all plage mamufectured or imported t Incorporate hnsabatad live plas from 3 April 2005 M ts required that all electrical equipment with ut Unwed pmpn he vd froen points od sudo by 3 April 2006 Your sincerely Fig 1 1 Australia Certificate of Approval TEST CERTIFICATE CERTIFICAT D ESSAI OC 59 Mo Deere Co ue NN See Bogen NR estan Peary Tace Patan UM D 20 Se Mg IU etm ni Terum Un TIAM Daraar ting Dectane Co LM Onna Nur Orne Ind Ls Bec Sewn Farg Samar Sararen PEOPLES POWER SUPPLY APPROVAL DOCUMENTS ta voae vee ea doe p Toate t y Mosa at TOC om te 1 08 er 24 om bw U vow m d eee o Papot pn Vea sna Rear Bey deme OC ow Orar de Carr om un TOV Podat Serves Dody Mete 0
4. SignalLED User Handbook This handbook is for use with the following stock codes LD 20F1REC LD 20F10NA LD 20F1MCL LD 40F1REC LD 40F10NA LD 40F1MCL LD 40F1PHN LD 40F1TRF LD 40F1ADB LD 40F1REH LD 40F1DOR LD 40F10BT LD 40F1NOE LD 40F1EXIT LD 40F1SIL LD 40F1MET LD 40F1INT LD 40F2TX REH LD 40F20NA MCL LD 40F20NA SIL LD 40E1REC LD 40E10NA LD 40E1MCL LD 40E2 LD KE1 LD KC1 LD IT LED Single Flush Mounting 20cm RECORD sign LED Single Flush Mounting 20cm ON AIR sign LED Single Flush Mounting 20cm MIC LIVE sign LED Single Flush Mounting 40cm RECORD sign LED Single Flush Mounting 40cm ON AIR sign LED Single Flush Mounting 40cm MIC LIVE sign LED Single Flush Mounting 40cm PHONE sign LED Single Flush Mounting 40cm TRAFFIC FLAG sign LED Single Flush Mounting 40cm AD BREAK sign LED Single Flush Mounting 40cm REHEARSAL sign LED Single Flush Mounting 40cm DOOR sign LED Single Flush Mounting 40cm OBIT sign LED Single Flush Mounting 40cm NO ENTRY sign LED Single Flush Mounting 40cm EXIT sign LED Single Flush Mounting 40cm SILENCE sign LED Single Flush Mounting 40cm MEETING IN PROGRESS sign LED Single Flush Mounting 40cm INTERVIEW IN PROGRESS sign Twin Flush Mounting Signs 2x20cm Twin TX amp REH sign Twin Flush Mounting Signs 2x20cm Twin ON AIR amp MIC LIVE sign Twin Flush Mounting Signs 2x20cm Twin ON AIR amp SILENCE sign SignalLED double sided end mounting 40cm RECORD sign
5. Please note do not to use excessive force when opening the cover LD 20F1 amp LD 40F1 Flush Sign Mounting Requirements This sign is to be mounted flush to a wall Minimum clearances from the sign to an adjacent wall or ceiling are shown below 30mm minimum clearance between ceiling and mounting hole Wall Ceiling LD 40F1 520 mm m LD 20F1 316 mm ia 200mm i Minimum clearance to an adjacent wall using 2 small 1 Pozi drive screwdriver e Mounting hole Fig 2 1 LD 20F1 amp LD 40F1 Flush Sign Mounting Requirements An absolute minimum of 60mm is required for the opened end cap a right angled screwdriver would be needed to screw unscrew the end cap retaining screw SONIFEX SignalLED User Handbook INSTALLATION 2 LD 40E1 amp LD 40E2 End Mounting Requirements Ceiling d TOR Wall Mounting Plate shown in red Z 38mm minimum jsi Y 0 Wall Mounting Holes 5 j Hanger Slots f 44mm To create an attractive invisible fixing finish i the SignalLED assembly is clipped into a wall mount plate The wall mount plate must be Emm securely fitted to a smooth solid surface before minimum attempting to fit the SignalLED assembly Drill 2 Clearance to open the holes approximately 34mm deep using a 6mm Erin diameter masonry drill and attach the wall
6. SignalLED double sided end mounting 40cm ON AIR sign SignalLED double sided end mounting 40cm MIC LIVE sign SignalLED twin double sided end mounting 2 x 20cm sign SignalLED conversion kit single flush mount to end mount Ceiling Mounting For 40cm Or 20cm Flush Mounting Signs SignalLED end mount sign installation tool STGNALLED STUDIO ILLUMINATED SIGNS HANDBOOK This handbook is for use with the following stock codes LD 20F1REC LED Single Flush Mounting 20cm RECORD sign LD 20F1ONA LED Single Flush Mounting 20cm ON AIR sign LD 20F1MCL LED Single Flush Mounting 20cm MIC LIVE sign LD 40F1REC LED Single Flush Mounting 40cm RECORD sign LD 40F10NA LED Single Flush Mounting 40cm ON AIR sign LD 40F1MCL LED Single Flush Mounting 40cm MIC LIVE sign LD 40F1PHN LED Single Flush Mounting 40cm PHONE sign LD 40F1TRF LED Single Flush Mounting 40cm TRAFFIC FLAG sign LD 40F1ADB LED Single Flush Mounting 40cm AD BREAK sign LD 40F1REH LED Single Flush Mounting 40cm REHEARSAL sign LD 40F1DOR LED Single Flush Mounting 40cm DOOR sign LD 40F10BT LED Single Flush Mounting 40cm OBIT sign LD 40F1NOE LED Single Flush Mounting 40cm NO ENTRY sign LD 40F1EXIT LED Single Flush Mounting 40cm EXIT sign LD 40F1SIL LED Single Flush Mounting 40cm SILENCE sign LD 40F1MET LED Single Flush Mounting 40cm MEETING IN PROGRESS sign LD 40F1INT LED Single Flush Mounting 40cm INTERVIEW IN PROGRESS sign LD 40E1MCL SignalLED double sided end mounting 40cm MIC LIVE sign
7. a ten page document 3 Fig 1 4 UL Certificate of Approval this is a one page document Fig 2 1 LD 20F1 amp LD 40F1 Flush Sign Mounting Requirements Fig 2 2 LD 40E1 amp LD 40E2 End Mounting Requirements Fig 2 3 LD KC1 Ceiling Mounting Kit Fig 2 4 Cable Routing Cut Outs Fig 2 5 Opening The Access Door Fig 2 6 Mode Settings amp Connection Bloc Fig 2 7 LD IT End Mount Sign Installation Tool Fig 2 8 Opening The Access Door Fig 2 9 Wire Link For Power Supply Fig 5 1 Sign Components to be Converted 14 Fig 5 2 Kit Components Used for the Conversion 15 Fig 5 3 Removing the Left Hand Assembly 15 Fig 5 4 Removing the Right Hand Flush Wall Moulding 16 Fig 5 5 Right Hand Conversion Re Assembly 16 Fig 5 6 Left Hand Conversion Re Assembly 17 NN 01 OQ Ui MN Wu FIGURES ii SONIFEX SignalLED User Handbook WARRANTY amp INTRODUCTION 1 Warranty Information This product is supplied with a 12 month back to base warranty For further details please refer to the Sonifex website http www sonifex co uk company terms index shtml gnal b LLL In order to register the date of purchase so that we can keep you informed of any design improvements or modifications it is important to complete the warranty registration document that is enclosed and return it to Sonifex Ltd in the UK For your own records you should write down the serial number of the SignalLED sign Serial Number
8. checked and the cables have been routed through the cable clamps close the end cover by reversing the opening procedure taking care not to overtighten the retaining screw SONIFEX SignalLED User Handbook PROGRAMMING Programming Colour amp Illumination Modes Although the SignalLED is delivered as standard to indicate a certain colour when a pull low to OV input signal is applied the sign is programmable to allow a number of different display modes and uses For example the sign can be made to switch between 4 colours one for each of the input conditions below The sign can also illuminate a certain colour when no input signal is connected i e it can be permanently illuminating or it can be made to switch from one colour to another on application of an input signal Setting The Colour amp Display Mode s of The Sign The sign can be set to illuminate in 4 different states according to the combination of the 2 x pull low signalling inputs present at the connector For each state the colour the illumination mode and the segments to be illuminated can be programmed To change the settings for any or all the signalling modes use the following instructions 1 Select Input Conditions There are four states of signalling inputs each of which may have different display modes To start the setup procedure select the signalling input state you wish to set as follows Set switches 2 and 3 to select the relevant input state e g if y
9. solely to document the use of Sonifex product SONIFEX SignalLED User Handbook CONTENTS Warranty Information Introduction Safety Information Handling Notes 4 Ir ny Power Supply Approval Documents Installation 4 Mounting The Sign 4 Opening The End Covers 4 LD 20F1 amp LD 40F1 Flush Sign Mounting Requirements 4 LD 40E1 amp LD 40E2 End Mounting Requirements 5 LD KC1 Ceiling Mounting Kit 5 A Connecting The Power and Signal Connections For Flush Mounted Signs 6 O Connecting The Power amp Signal Connections For End Mounted Signs 7 2 Power Supply 7 Programming Colour amp Illumination Modes E m Setting The Colour amp Display Mode s of The Sign 9 1 Select Input Conditions 9 a 2 Colour 10 2 1 Load Colour Settings 11 3 Setting Which Side Segment of Your Sign Illuminates 11 3 1 Load Segment Selection Setting 11 4 Setting the Illumination Mode 12 4 1 Load Illumination Mode Setting 12 Technical Specifications 13 Appendix 1 14 LD KE1 SignalLED Conversion Kit Single Flush Mount to End Mount 14 Right Hand Side Fitting of the Conversion Kit 14 Left Hand Side Fitting of the Conversion Kit 16 Appendix 2 18 SignalLED Preconfigurations 18 SignalLED User Handbook SONIFEX FIGURES Fig 1 1 Australia Certificate of Approval this is a three page document Fig 1 2 CB Certificate of Approval this is a two page document Fig 1 3 CE Certificate of Approval this is
10. ver mount plate coloured red in the illustration above to the wall At this point the LD IT end Fig 2 2 LD 40E1 amp LD 40E2 End Mounting mount installation tool can be used to hold the Requirements sign in place while you connect the power and signal cables The cable retention clips can be used to hold the cables in the sign See page 4 for information on connecting the Power and Signal cables The sign is fitted by locating the four internal hanger plate hooks into the four slots in the wall mount plate Once located hold the sign around the end moulding of the SignalLED assembly where the door is fitted and press down into its final position The sign retaining pins will clip into the indentations on the side of the wall mount plate and this should result in a click as the plastic pins move into their final position Note a reasonable amount of force is needed to fully connect the LED sign assembly to the wall plate LD KC1 Ceiling Mounting Kit Open the end covers of the sign Take the 5mm screw out of each of the PN LD KC1 brackets and use the screws to attach the sign covers to them Y where indicated on the drawing below Ensure that the sign cover 65mm Bomm sits comfortably against the metal plates on each of the bracket Q li H The LD KC1 ceiling mounting kit can be used for mounting a 40cm or pe ll 20cm flush mounting sign either down from the ceiling _ pU E Y or up from a surface e g table top M 33
11. water or mild detergent Avoid using the SignalLED sign close to strong sources of electromagnetic radiation such as video monitors or high power electric cabling In all cases the SignalLED sign should be installed and serviced by qualified personnel SignalLED User Handbook SONIFEX 1 POWER SUPPLY APPROVAL DOCUMENTS Power Supply Approval Documents The power supply used with the SignalLEDs is UL EC and CC TW ans Queensland Government SEE approved For a more detailed view ELIT MN of the certificates please check 2005 ta online at http www sonifex co uk N A i e i are signalled index shtml Citt Hosen amp Tbe Deep Dies Deu Me Qi CERTIFICATE OF APPROVAL OF PRESCRIBED ELECTRICAL EQUIPMENT EXTRA LOW VOLTAGE POWER SUPPLY UNIT POWER ADAPTOR MODEL NO 34 065 WFXXA Lars pleased to wdvise that your application for approval ef the above mentioned electrical been approved Tho regumviton masher vo de equipement is 005363 number wat be maria on all epee Qa emidesed Aeenatvely you may the Compliance Mark RCM ieu of a manier advise if yon mess ha RCM in es of mambar Tienes mate tat it la requirement of the Electrical Safety Act Raguiesons 2002 that if you modify the electrical equipement wey you are
12. 0 40220 Maruti Fig 1 2 CB Certificate of Approval Tamil 2 SONIFEX SignalLED User Handbook POWER SUPPLY APPROVAL DOCUMENTS 3 Ir CERTIFICATE No 21 05 06 17627 124 Holder of Certificate ENG Electric Co Ltd SNe 536 Sec NAS Taoyan wan e CERTIFICADO e CERTIFICAT akii sa mee BUZ dius o E o gt N NW Pedes oues Qui Vr eee Dnus ee NIMM Brem Fig 1 3 CE Certificate of Approval Mm et doemme pedet po aiia LL Ma eren m pd Sli of Unis absens nc LL oem pot prin Bos buen complot undo aua prope mand ond da soni ssim er C Fat Serva Prey oad ror e ec ap i UL La en Ae UL hare Up hovers Regum te mi pedes Va em S1LN1Wn 50Od 1VAOHUddV AlddNS H3MOd See singe ting ANP Ps A A AA Ta premda la wet the meen lt LL MA the addons dl ca ay Not E sanhas manai 1 meg w omy mand m Fin LT Va Xi etario on 4 den Ni sd Bu pd cd ir o do he Pelo Up Servi Pc Be prac sum hong und wd ha a a nm tg Voss son Rus Pc ty utm ht Apes M Piet Ba UL Mai dui Vo into to es cid vy UL d to immi UL ro Hangs caretes deer eres erem v Ve has bo pude nt cular dh v rerum etu m id ha LL Mah
13. EN E EH 12345078 then 123345601008 SignalLED User Handbook SONIFEX 3 v DNIWINVHDOSd 11 v z z lt x o o 12 PROGRAMMING 4 Setting the Illumination Mode E 1 1 1 ON OFF AS DIPSwitches Off On Off of of Hg ERE Constantly A DIPSwitches 0 5 sec off Si 9n On gn Du A a Oo continuous 1293 24 5 OTE Pulsing DIPSwitches 4 x on off in 0 5 sec Off On Off On Off E 0 5 sec off continuous DIPSwitches Alternate of on on on of gat unas Flash Mode UN DIPSwitches Follow Mode Off On On On On A a A a A A a AAA OTS Note Alternate Flash amp Follow modes can only be assigned when both pull low inputs are active so DIPSwitches 2 amp 3 must both be set to On They will illuminate the two halves of the sign according to the modes set for input 1 and input 2 These modes are designed for 40cm signs that have segments independently set by signalling modes 2 amp 3 4 1 Load Illumination Mode Setting Once the DIPSwitches are set in the required state toggle SW1 ie switch SW1 on and then off DIPSwitches DIPSwitches Eg then E lg La S25 2S 2 Fe 5 Next Steps Now repeat steps 1 4 for all remaining input conditions to be changed and then return all switches to the off state Note Remember if you re using both inputs to control the sign you need t
14. ES 3 Align the 4 pins of the extrusion end cover with the screw holes in the exposed end ofthe aluminium tube Note the orientation of the cut out with the clear sign board and press fit the end cover fully onto the aluminium tube 4 Openthe end cover on the right hand flush mount assembly by removing the self tapping screw with a No 1 pozi drive screwdriver CE 5 Remove the flush wall mount moulding from the end moulding by unscrewing the 4 screws visible under the cover See Fig 5 4 6 Fittheinternal hanger plate into the end wall mount moulding Align the semi circular cut out in the hanger plate with the raised section above the serial number label which indicates the bottom of the assembly Also make sure that the hanger plate fits into the slots in the wall mount moulding 7 This combination is then fixed to the right hand flush mount assembly end moulding with the 4 supplied No 4 x 34 self tap screws See Fig 5 5 Do not substitute any other screws in these positions and do not reuse the screws removed from these positions because they will not support the sign correctly S32IaNaddv 8 Please refer to the installation notes for the LD 40E style signs to complete the final fitting and colour configuration set up Remove these screws to take off the left hand flush mount End wall mount assembly moulding Ormmumm No 4 x 74 selftap 7 LI screws x 4 Extrusion end cover Fig 5 2 Kit Co
15. It is recommended that the LD IT SignalLED end mount sign installation tool is used to assist the termination of the power and signal connections The tool is designed to hold the sign on the pre fitted wall mount plate leaving both hands free to make the connections as shown in Fig 2 7 LD IT SignalLED Wall End mount sign mount installation tool plate 1 Align tool hooks with the slots in 2 Align sign hooks tne wall mount plate Cable connection with the slots in the tool plate d block Fig 2 7 LD IT End Mount Sign Installation Tool To get access to the cable connection block and the mode switches which are on the PCB inside the sign the door on the underside of the end plastic moulding must be opened To open the door push the clip towards the sign and pull down on the small lip See Fig 2 8 Do not attempt to remove the door from the end moulding Access to the connection block and the mode switches is possible with the door fully open To open the door push the clip and pull on the small lip Fig 2 8 Opening The Access Door Power Supply The sign can be connected and powered either with the supplied DC power supply or with a regulated DC supply rated 5V to 7V DC 0 5mA minimum On the supplied DC power supply the 6V is indicated with a dashed white line on one of the cables Pin 1 Signalling Input 1 Pin2 6V I Wire Link Pin3 0V Pin4 Signallin
16. LD 40E1ONA SignalLED double sided end mounting 40cm ON AIR sign LD 40E1REC SignalLED double sided end mounting 40cm RECORD sign LD 40E2 SignalLED twin double sided end mounting 2 x 20cm sign LD IT SignalLED end mount sign installation tool LD KC1 Ceiling Mounting For 40cm Or 20cm Flush Mounting Signs LD KE1 SignalLED conversion kit single flush mount to end mount OSonifex Ltd 2009 2010 All Rights Reserved Revision 1 07 June 2010 This version combines the LD F1 and the LD E1 handbooks Sonifex Ltd 61 Station Road Irthlingborough Northants NN9 5QE England Tel 44 0 1933 650 700 Fax 44 0 1933 650 726 Email sales sonifex co uk Website http www sonifex co uk Information in this document is subject to change without notice and does not represent a commitment on the part of the vendor Sonifex Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual SIGNALLED STUDIO ILLUMINATED SIGNS HANDBOOK No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying recording information storage and retrieval systems for any purpose other than the purchaser s personal use without the express written permission of Sonifex Ltd Unless otherwise noted all names of companies products and persons contained herein are part of a completely fictitious adaptation and are designed
17. S Mode On On On On On Dual Colour E 1 Note Dual Colour Mode can only be assigned when both inputs are active it will illuminate the two halves of the sign according to the colours set for input 1 and input 2 individually 10 SONIFEX SignalLED User Handbook PROGRAMMING 2 1 Load Colour Settings Once the DIPSwitches are set the required state toggle SW1 i e DIPSwitch SW1 On and then Off to set the colour DIPSwitches DIPSwitches then O B DO Wu De UU Wu Gut 1 1 1 ON OFF As Previous 3 Setting Which Side Segment of Your Sign Illuminates For 40cm signs the two sides of the sign can be controlled independently i e different colours and flashing modes can be controlled on each side Side Segment SWT4 SWT5 SWTG6 SWT7 SWT8 of DIPSwitches 1 the sign o rT TTT nearest the Off Off Off Off Off connection block dim of DIPSwitches the sign MET Off Off On Off Off E E O o B from the 1293 245 ESE connection block DIPSwitches Whole Sign EEE o 8 NO EO NOTAS Note The slave segment is not valid for 20cm signs and so selecting this option with a 20cm sign will mean that the sign will appear to be switched off 3 1 Load Segment Selection Setting Once the DIPSwitches are set in the required state toggle SW1 i e DIPSwitch 1 On and then Off to set the segment selection DIPSwitches DIPSwitches
18. connected to 0V urns the sign off LD 40F10BT Turns the whole sign solid white when connected to 0V amd LD 40F10NA Turns the whole sign solid red when connected to 0V urns the sign off LD 40F1PHN Turns the whole sign solid white when connected to 0V mdd LD 40F1REC Turns the whole sign solid green when connected to 0V urns the signoff LD 40F1REH Turns the whole sign solid red when connected to 0V use diesincli LD 40F1SIL Turns the whole sign solid orange when connected to 0V urns the signoff LD 40F1TRF Turns the whole sign solid green when connected to 0V ste LD 40F20NA MCL Turns the ON AIR segment solid green urns the MIC LIVE segment solid red and the ON when connected to 0V AIR segment solid green when connected OV Turns the ON AIR segment solid red Turns the SILENCE segment solid orange and the LD 40F20NA SIL when connected to 0V ON AIR segment solid red when connected to OV LD 40F2TX REH Turns the TX segment solid red Alternates REH in solid blue TX in solid red when connected to 0V SignalLED User Handbook SONIFEX 19 SONIFEX www sonifex co uk t 44 0 1933 650 700 f 44 0 1933 650 726 sales sonifex co uk
19. g Input 2 Fig 2 9 Wire Link For Power Supply SignalLED User Handbook SONIFEX CE NOILVTIVISNI INSTALLATION INSTALLATION The signalling inputs are used to control the sign and are pulled low to OV pin 3 to activate Please note pins 3 OV and 1 input 1 are linked by default so that the sign will illuminate in its default mode when first powered up The power supply OV is then inserted into pin 3 along with the link and the 6V supply into pin 2 The positive voltage is normally marked by a white stripe on the relevant wire test this with a voltmeter if you are unsure If the sign needs to be controlled externally remove the link and fit a switch or other contact closure If you wish to use the sign in its alternate mode remove this link and link pin 4 to pin 3 instead Use a small flat blade screwdriver to undo the connection block screw terminals and also to adjust the mode switches see following for information on this Do not fully remove the screws from the terminals they only need 2 or 3 full turns to accept the wire ends Also take care not to apply too much force to the connection block when fitting the wire ends as this could damage the PCB When the power and signalling connections have been made and the mode switches set up close the access door by pressing the clip back to its original position It will click into place when it is fully home After all of the terminations have been
20. g the self tapping screw with a No 1 pozi drive screwdriver 6 Remove the flush wall mount moulding from the end moulding by unscrewing the 4 screws visible under the cover 7 Replace the PCB into the left hand end moulding aligning the PCB edge with the guide tracks in the aluminium extrusion Refit the 2 small screws that hold the PCB taking care not to over tighten and strip the plastic 8 Fitthe internal hanger plate into the end wall mount moulding Align the semi circular cut out in the hanger plate with the raised section above the serial number label which indicates the bottom of the assembly Also make sure that the hanger plate fits into the slots in the wall mount moulding 16 SONIFEX SignalLED User Handbook APPENDICES 5 9 This combination is then fixed to the left hand flush mount assembly end moulding with the 4 supplied No 4 x 34 self tap screws Do not substitute any other screws in these positions and do not reuse the screws removed from these positions because they will not support the sign correctly 10 Please refer to the installation notes for the LD 40E style signs to complete the final fitting and colour configuration set up LED PCB fixing screws gt v v m 2 A m Uu Internal Hanger plate semi circular location cut out Fig 5 6 Left Hand Conversion Re Assembly SignalLED User Handbook SONIFEX 17 5 APPENDICES Appendix 2 SignalLED Preconfigurat
21. ign Twin Flush Mounting Signs 2x 20cm LD 40F2TX REH 2 x 20cm TX amp REH Sign LD 40F20NA MCL 2 x 20cm ON AIR amp MIC LIVE Sign Double Sided End Mounting Signs 40cm LD 40E1REC 40cm RECORD Sign LD 40E1ONA 40cm ON AIR Sign LD 40E1MCL 40cm MIC LIVE Sign Mounting Kits 00000 LD KE1 End Mounting Kit For 40cm Or 20cm Flush Mounting Signs LD IT LED Sign End Mounting Installation Tool LD KC1 SignalLED Ceiling or Desk Mount Bracket Pair Weights amp Boxed Dimensions Sign Type Width cm Depth cm Height cm Gross Weight cm Net Weight kg LD 20F1 style signs 39 20 11 1 0 0 65 LD 40E1 style signs 60 20 11 11 0 75 LD 40E2 style signs 60 20 11 1 1 0 75 LD 40F1 style signs 60 20 11 11 0 75 LD 40F2 style signs 60 20 11 TA 0 75 Note Weights are approximate and based on a sign supplied with the PSU SignalLED User Handbook SONIFEX 13 APPENDICES Appendix 1 LD KE1 SignalLED Conversion Kit Single Flush Mount to End Mount To convert the LD 20F amp LD 40F style flush mount single sided signs into single sided end mount signs you will need to fit the LD KE1 conversion kit Please follow these instructions carefully Ir n Note You ll need the following tools to use the conversion kit a No 0 and No 1 Pozi drive screwdriver Take care not to damage the clear surface of the sign board The surface will be marked by swarf or rough surfaces so please use a clean cloth to hold the
22. ions Top Level Part Number Master 1 Side with connections No Input Please note that your SignalLED sign has been preconfigured for the following operation oe depending on the sign chosen Input 1 Default link between pins 1 and3 on the power connector LD 20F1MCL MIC LIVE Turns the sign off beet dun id red Y LD 20F10NA ON AIR Turns the sign off pewno us id green F LD 20F1REC RECORD Turns the sign off ed id red a LD 40E1MCL MIC LIVE Turns the sign off Mou S apa idived arc v LD 40E1REC RECORD LD 40F1ADB AD BREAK Turns the sign off bui pda id red voor Tr the hale on bl Lo oriexit _ Furs thesign ott Tums the wnole tons green LD 40F1INT pipa LD 40F1MCL MIC LIVE Turns the sign off Tuns id red LD 40F1MET did unser okle LD 40F1NOE NO ENTRY Turns the sign off bos id red om Tunsthesgn LO 4OFIONA onan ns the sign ott Tums the wnole tons oreen LO 4OFIPHN phone siono Tams the whole sign soid yelow LO 4OFIREC coro fums the Tuma the whol ion sold rd LD 40F1REH REHEARSAL LD 40F1SIL SILENCE Turns the sign off Um Pewne aano id red LD 40F1TRF TRAFFIC FLAG
23. mm _ or top of a rack Metal Plate 5mm screw goes here Fig 2 3 LD KC1 Ceiling Mounting Kit SignalLED User Handbook SONIFEX TER eu n NOILVTIVISNI ins fs INSTALLATION INSTALLATION Connecting The Power and Signal Connections For Flush Mounted Signs To get access to the cable connection block and the mode switches which are on the PCB inside the sign the door on the underside of the end plastic moulding must be opened To open the door push the clip towards the sign and pull down on the small lip see Fig 2 5 Do not attempt to remove the door from the end moulding Access to the connection block and the mode switches is possible with the door fully open Three cable cut out points in the wall mount face of the plastic moulding To open the door push the clip and pull on the small lip Fig 2 4 Cable Routing Cut Outs Fig 2 5 Opening The Access Door Settings Switch Connection ON Block SONIFEX This product is RoHS 12345678 manufactured after 13th August 2005 www co uk o a i For activation short inputs meu H E 2 JHBBBHHH to 0V Fig 2 6 Mode Settings 8 Connection Bloc SONIFEX SignalLED User Handbook INSTALLATION Connecting The Power amp Signal Connections For End Mounted Signs
24. mponents Used for the Conversion Fig 5 3 Removing the Left Hand Assembly SignalLED User Handbook SONIFEX 15 APPENDICES Remove these screws to take e End wall mount E moulding Internal plate 7 semi circular from the assembly location cut out Fig 5 4 Removing the Right Hand Flush Wall Moulding Fig 5 5 Right Hand Conversion Re Assembly Left Hand Side Fitting of the Conversion Kit Note With this conversion you will be removing the PCB from the sign so full anti static precautions must be taken to protect the PCB from damage Failure to do so may result in the sign not working and invalidating the warranty APPENDICES 1 Open the end cover on the right hand flush mount assembly by removing the self tapping screw with a No 1 pozi drive screwdriver 2 Remove the 2 small screws that hold the PCB into the right hand flush mount assembly and withdraw the PCB Place the PCB on an antistatic surface 3 Remove the right hand flush mount assembly by unscrewing the 4 screws that fix the end moulding to the aluminium tube These are located inside at the bottom of the end moulding 4 Align the 4 pins of the extrusion end cover with the screw holes in the exposed end of the aluminium tube Note the orientation of the cut out with the clear sign board and press fit the end cover fully onto the aluminium tube 5 Openthe end cover on the left hand flush mount assembly by removin
25. my be ola Brin H A LI EIE iic estas ERE EE mM d eir dae m Fig 1 4 UL Certificate of Approval SignalLED User Handbook SONIFEX 3 2 3 INSTALLATION INSTALLATION Installation Mounting The Sign Route the signal and power supply cables before finalising the mounting of the sign These cables can be routed either through the aperture or through the cable cut outs in the back of the wall mount moulding The LED sign should be mounted on a firm solid surface The sign is supplied with a mounting kit comprising 2 x wall plugs and 2 x large flange screws Note You ll need the following tools to mount the sign an electric drill fitted with a 6mm diameter masonry drill bit a No 1 Pozi drive screwdriver and a spirit level 5 Drill 2 holes approximately 34mm deep using a 6mm diameter masonry drill at the pitch shown on the drawings Insert the wall plugs flush with the surface Use a spirit level on the aluminium tube section to set the sign level before fully tightening The screws can also be used for fixing into wood For correct fitting drill a small pilot hole into the wood before fitting the screw Opening The End Covers To get access to the sign mounting points the side covers need to be opened Use a No 1 Pozi drive screwdriver to unscrew the side cover and gently slide the cover forward approximately 8mm until it reaches the stops Pivot open the cover
26. o configure the case when both inputs are active as well as when each individual input is active Dual Colour Mode page 8 may be useful in this application SONIFEX SignalLED User Handbook S D TECHNICAL SPECIFICATION 4 Technical Specifications Power Supply Plug top power supply providing 6V at 1A with 4 international wall adapters UK EU US and AUS and 5m lead to bare ends Power Input 5 7V DC 40cm Sign 500mA max Input Connector 4 way screw terminal block Control Inputs 2x pull down to Perspex Dimensions Single 40cm W x 8cm H Overall Sign Dimensions LD 20F1 333mm x 129mm x 60mm LD 40E1 493mm x 149mm x 71mm LD 40E2 493mm x 149mm x 71mm LD40 F1 527mm x 129mm x 60mm LD 40F2 527mm x 129mm x 60mm m A Z LD 20F1REC 20cm RECORD Sign LD 20F10NA 20cm ON AIR Sign A LD 20F1MCL 20cm MIC LIVE Sign Single Flush Mounting Signs 40 LD 40F1REC 40cm RECORD Sign LD 40F1ONA 40cm ON AIR Sign LD 40F1MCL 40cm MIC LIVE Sign A LD 40F1PHN 40cm PHONE Sign LD 40F1TRF 40cm TRAFFIC FLAG ON Sign LD 40F1ADB 40cm AD BREAK Sign n LD 40F 1REH 40cm REHEARSAL Sign gt LD 40F1DOR 40cm DOOR Sign LD 40F10BT 40cm OBIT Sign LD 40F1NOE 40cm ENTRY Sign LD 40F1EXIT 40cm EXIT Sign Z LD 40F1SIL 40cm SILENCE PLEASE Sign LD 40F1MET 40cm MEETING IN PROGRESS Sign LD 40F1INT 40cm INTERVIEW IN PROGRESS S
27. ou want to use Signalling input 1 to control the sign then set SWT2 to On and SWT3 to Off 1 1 1 ON OFF As Previous DIPSwitches Program resting when no 1 Off Off E a A E A E signalling inputs active Input State signalling swT3 ZO y DIPSwitches Signalling Input 1 active 2 On Off E A A A p E A E LHS Zeg 675 DIPSwitches Signalling Input 2 active 3 Off On E A A E A El A LATAS wd DIPSwitches Signalling Input 1 amp Input 2 active Egg ERN i BP DO YO Now select the colour that you want the sign to show when the input state above is used SignalLED User Handbook SONIFEX 3 1 MET DNIWIAVHDOHUd 3 PROGRAMMING 2 Colour To choose the colour of the sign set the switches as follows A 7 1 mal y Colour SWTA SWT5 SWT6 SWT7 SWT8 ON OFF As t Previous 1 1 ote DIPSwitches QE OHXUS ox DIPSwitches E LADA G7 DIPSwitches E gQEgEH LAS eo DIPSwitches E gl VASO E DIPSwitches E IE RENNES DIPSwitches Magenta On On Off On Off EH A E QE v Eq A DIPSwitches Yellow On Off On On of B H E EN E 10925053 084 e DIPSwitches White On On On On of M ggggE 1 DEGEANDNORUSS PROGRAMMING DIPSwitches Orange On Off Off Off On EEE O 1 2S Oe DIPSwitches Brick Red On On Off Off On E ggg TAR AB OTE DIPSwitches PEELE Tey ey H
28. sign Because the sign is single sided the text will only be correctly viewable from one side If the text must be viewed from one particular side this must be chosen initially as it will affect the disassembly and subsequent re assembly of the sign As standard the SignalLED PCB is fitted into the right hand end of the LD 20F amp LD 40F see Fig 5 1 If you would like the sign to be viewable with the right hand side of the sign mounted onto the wall please use the Right Hand Side fitting instructions APPENDICES If you would like the sign to be viewable with the left hand side of the sign mounted onto the wall please use the Left Hand Side fitting instructions Flush wall mount moulding End moulding Top View Left hand flush ight hand mount assembly HE E flush mount assembly Flush wall Aluminium tube mount end cover Front View Fig 5 1 Sign Components to be Converted Right Hand Side Fitting of the Conversion Kit 1 Open the end cover on the left hand flush mount assembly by removing the self tapping screw with a No 1 pozi drive screwdriver 2 Remove the left hand flush mount assembly by unscrewing the 4 screws that fix the end moulding to the aluminium tube These are located inside at the bottom of the end moulding See Fig 5 3 14 SONIFEX SignalLED User Handbook APPENDIC
Download Pdf Manuals
Related Search