DT-X71C/H/F Operation manual
Contents
1.2. User Manual Model DT X71F HDSDI amp HDMI Waveform Audio meter Focus assist DT X71H HDSDI amp HDMI DT X71C HDMI Please read this User Manual throughout before using Preface Congratulations on your purchase of this product Please read this user manual carefully 1 All internal technologies of this product are protected including device software and trademark Reproduction in whole or in part without written permission is prohibited 2 All brands and trademarks are protected and other relative trademarks in this user manual are the properties of their respective owners 3 Due to constant effort of product development Swit Electronics reserves the right to make changes and improvements to the product described in this manual without prior notice 4 This product is covered by 2 years conditional warranty and misuse abnormal handling alterations or modifications in design or construction will void this warranty It is considered normal that the LCD bright dot defects are not to exceed three 5 For any suggestions and requirements on this product please contact us through phone fax Email etc SWIT Electronics Co Ltd SWIT Electronics USA LLC Address 4300 Stevens Creek Blvd Suite 230 San Jose CA 95129 Toll free 1 866 986 SWIT 7948 Tel 408 260 8258 Fax 408 228 8438 Email info swit us Website www swit us Maintenance Monitor 1 Please keep the signal terminals and the cooling vent aw
3. ELT Rear view W J oOo o Ir Oo si I O 6 A 2 ay I oO 6 a jae GEES Fs gt NCD I M N i i oe aod P Set Ee Q Y og Ti ili ry DY ie AS AAN Y D N ty 4 7 X a eA E S _ EF a UA a 1 2 3 4 5 9 8X7 6 1 DC 12V IN Connect with DC12V 4 pin XLR power adapter 2 TALLY Light Red Green and Yellow 3 color TALLY indicator 3 Battery mount Connect with JVC battery BN VF823 or SWIT battery BN S8823 to power the monitor 4 HDSDIIN1 2 HD SD SDI input BNC connector 5 HDSDI OUT HD SD SDI loop through output BNC connector 6 HDSDI LOOP1 2 HD SD SDI loop through output BNC connector 7 VIDEO IN Composite video input BNC connector 8 TALLY controlling port RJ45 9 HDMI HDMI input Input formats Input Supported formats CVBS PAL NTSC 4801 5761 480P 576P 1080i 60 59 94 50 720p 60 59 94 50 1080p 60 59 94 50 30 29 97 25 24 23 98 1080i 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 23 98 SDI SMPTE 296M _ 720p 60 59 94 50 SMPTE 125M _ 480i 59 94 ITU R BT 656 576i 50 HDMI DT X71H Front view 1 2 1 2 a a a3 13 PHONE Earphone jack POWER Power on off Connect with power cable or mount ba
4. people in front of the camera as well as the camera operator behind DT X71C New high resolution 7 LCD Panel 16 9 1024x600 16 77 million colors 900 1 contrast and H160 V160 viewing angle Multiple inputs 1 HDMI 1 Composite input and L R stereo audio input Loop through outputs 1 Composite loop through output DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor Image Flip Set image to rotate by 180 2 Panel Instruction User definable function keys There are 2 function keys on the monitor front panel and users could define the functions to the keys to achieve shortcut User editable video title User can edit a video title for the current camera and the title will display on the top of screen Front and Rear 3 color TALLY light 2 TALLY lights design to give live signals to people in front of the camera as well as the camera operator behind DT X71F Front view 1 2 3 9 10 11 12 13 1 PHONE Earphone jack 2 POWER Power on off Connect with power cable or mount battery press the POWER and the power indicator is turned on and after 10 seconds the monitor will be switched on and get into normal working status Press the POWER again the indicator is turned off and monitor is switched off Disconnect with power cable or take off the battery if the monito
5. 02 SCAN Underscan Overscan switch 03 ZOOM Picture Zoom in 04 PIC MODE Preset picture mode switch 05 B W Color Black amp white switch 06 BLUE ONLY Blue only mode switch on off 07 ZEBRA Zebra over exposure switch on off 08 VECTOR Vector scope switch on off 09 PATTERN Internal colorbar switch on off 10 RGB HIST R G B Histogram switch on off 11 TIMECODE SDI timecode display switch on off 12 F COLOR False color mode switch on off 13 AUDIO BAR Audio meter display switch on off 14 FOCUS Peaking focus assist switch on off and red blue selection 10 TALLY Light Operation EATI 01 RATIO Aspect ratio switch 02 SCAN Underscan Overscan switch 03 ZOOM Picture Zoom in 04 CLR TEMP Color temperature switch 05 PIC MODE Preset picture mode switch 06 B W Color Black amp white switch 07 REVERSE Image flip 01 RATIO Aspect ratio switch 02 SCAN Underscan Overscan switch 03 ZOOM Picture Zoom in 04 CLR TEMP Color temperature switch 05 PIC MODE Preset picture mode switch 06 B W Color Black amp white switch 07 REVERSE Image flip There are front and rear TALLY lights on the monitor which can display RED GREEN and YELLOW signals The TALLY light controlling port is the RJ45 socket at the rear panel and terminal description is as follows Terminal 1 2 3 4 5 6 7 8 Description Y G GND R The RED light is on when connecting the terminal R with GND and goes out
6. LCD 4 For first time use please tear off the factory LCD film To protect the LCD screen please post the LCD protection film offered in the package 1 Features DT X71F New high resolution 7 LCD Panel 16 9 1024x600 16 77 million colors 900 1 contrast and H160 V160 viewing angle Multiple inputs 2 HD SD SDI 1 HDMI and 1 Composite input Loop through outputs Each of the 2 input HD SD SDI has loop through output HDMI converted to SDI output Supported HDMI formats 480i 576i 720p 50 59 94 60 1080i 50 59 94 60 1080P 23 98 24 25 29 97 30 and the output SDI will embed the audio 48KHz from HDMI Waveform Y Cb Cr R G B and full scale There are totally 6 kinds of waveform display available under both SDI and HDMI to check the Luminance Y Blue difference Cb Red difference Cr Red R Green G Blue B and the Y Cb Cr can be simultaneously displayed R G B can be simultaneously displayed and each of the waveforms can be set to full scale display Vector scope The displayed vector scope pattern is available under both SDI and HDMI represents saturation as distance from the center of the circle and hue as the angle in standard position around it Histogram R G B The histogram is a bar graph that shows the distribution of luminance values in the picture There re R G B histograms that individually displayed simultaneously available under both SDI a
7. when disconnecting The GREEN light is on when connecting the terminal G with GND and goes out when disconnecting The YELLOW light is on when connecting the terminal Y with GND and goes out when disconnecting 11 Specifications LCD Performance Size 7 0 inches 1024 X RGB x 600 16 9 4 3 NTSC PAL 400cd m 900 1 16 77 million colors H V 160 160 Resolution Aspect ratio Color system Brightness Contrast Color Viewing angle Video Format 1080 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 23 98 SDI SMPTE 296M 720p 60 59 94 50 SMPTE 125M 480i 59 94 ITU R BT 656 576i 50 4801 5761 480P 576P 1080i 60 59 94 50 720p 60 59 94 50 1080p 60 59 94 50 30 29 97 25 24 23 98 DT X71C doesn t support SDI input HDMI 12 Packing List 1 Monitor x 2 User Manual x 1 3 Power adaptor x 1 4 Power cable x 5 Sun hood x1 6 Screw ball head x1 7 LCD protection film x1 This model is manufactured warranted and supported by SWIT Electronics Co Ltd SWIT Electronics USA LLC and distributed in North America by JVC Professional Video Products To obtain service or for further information please contact SWIT Electronics USA LLC Address 4300 Stevens Creek Blvd Suite 230 San Jose CA 95129 Toll free 1 866 986 SWIT 7948 Tel 408 260 8258 Fax 408 228 8438 Email info swit us e Website www swit us
8. 59 94 50 30 29 97 25 24 23 98 oO Menu Operation Press MENU and it will display menu system Revolve OK to select an item The selected item will be highlighted display Press OK to enter the selected item Under menu system press MENU to back to previous menu The menu will automatically save and quit if it remains idle V VV V 4 Picture Settings Submenu The Picture Settings Submenu includes 1 CONTRAST 0 100 value adjustment 2 BRIGHTNESS 0 100 value adjustment 3 HUE 0 100 value adjustment Only available under Composite input 4 SATURATION 0 100 value adjustment 5 SHARPNESS 0 100 value adjustment 6 PIC MODE User defined and preset picture modes standard soft and vivid selection PICTURE ADJ OK gt EXIT 5 System Configuration Submenu The System Configuration Submenu includes 1 RATIO Select 16 9 or 4 3 to adjust the aspect ratio 2 SCAN UNDERSCAN OVERSCAN selection 3 ZOOM OFF ZOOM1 and ZOOM selection ZOOM1 Canon DSLR scale zoom in ZOOM2 Pixel to Pixel zoom in 4 MARKER Select and set the safety mark scale from 80 85 90 and 95 5 FLIP Select YES to enable G sensor auto flip 6 RESET Revolve OK to RESET and press to recover all to factory setting ADJ OK OK MENU EXIT 6 OSD Settings Submenu The OSD Settings Submenu includes 1 LANGUAGE M
9. C battery BN VF823 or SWIT battery BN S8823 to power the monitor 4 HDSDIIN1 2 HD SD SDI input BNC connector 5 HDSDI OUT HD SD SDI loop through output BNC connector 6 VIDEO IN Composite video input BNC connector 7 AUDIO L R Stereo audio L R input RCA connector 8 TALLY controlling port 9 HDMI HDMI input Input formats Input Supported formats CVBS PAL NTSC 4801 5761 480P 576P 1080i 60 59 94 50 720p 60 59 94 50 1080p 60 59 94 50 30 29 97 25 24 23 98 1080i 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 23 98 SDI SMPTE 296M _ 720p 60 59 94 50 SMPTE 125M _ 480i 59 94 ITU R BT 656 576i 50 HDMI DT X71C Front view 14 Pao 3 4 5 6 7 aa f O fey A YIDEO HDMI B W OVERSCAN MENU f PHONE POWER Wh E RA om DISPLAY f 1 2 a a a3 13 1 PHONE Earphone jack 2 3 4 9 6 7 8 9 10 11 12 13 14 POWER Power on off Connect with power cable or mount battery press the POWER and the power indicator is turned on and after 10 seconds the monitor will be switched on and get into normal working status Press the POWER again the indicator is turned off and monitor is switched off Remark Disconnect with power cable or take off the battery if the monitor will not be used for a period of time VIDEO Press to switch the input signal to Composite video HDMI
10. Press to switch the input signal to HDMI B W Black and White mode OVERSCAN Overscan Underscan switch MENU Press to enter Menu F1 User definable function key 1 F2 User definable function key 2 RATIO 16 9 and 4 3 switch ZOOM Picture Zoom in Press ZOOM to switch ZOOM1 Canon DSLR scale zoom in and ZOOM2 pixel to pixel zoom in DISPLAY Display current settings Press Display to display safety mark title and the current input signal information OK Select and Apply Under menu system revolve OK to adjust settings and press to apply and out of menu system directly revolve OK to adjust volume TALLY Light Red Green and Yellow 3 color TALLY indicator Rear view 5 aa aO N i PENN IDEO on v Deon gt VAN f N r NAN IKO a Se OO SY 00i004 pp A 8 2 3 4 d DC 12V IN Connect with DC12V 4 pin XLR power adapter 2 Battery mount Connect with JVC battery BN VF823 or SWIT battery BN S8823 to power the monitor 3 VIDEO OUT Composite video loop through output BNC connector 4 AUDIO L R Stereo audio L R input RCA connector 5 VIDEO IN Composite video input BNC connector 6 HDMI HDMI input 7 TALLY controlling port 8 TALLY Light Red Green and Yellow 3 color TALLY indicator Input formats Input CVBS HDMI Supported formats PAL NTSC 4801 5761 480P 576P 1080i 60 59 94 50 720p 60 59 94 50 1080p 60
11. ay from knife edge metal or liquid in order to avoid short circuit and damage 2 Please don t try to disassemble any parts of the monitor by yourself which would probably damage the monitor and do harm to human body and it will cause the invalidation of product warranty 3 Please don t touch the screen with your fingers which would probably deface the screen 4 Please don t press the screen the LCD is extremely exquisite and flimsy The power Please use the provided power adapter or the battery recommended by the manufacturer in order to avoid damage Please never use the light connector 2 pin female in right front of camera handle to power the monitor otherwise it will damage the circuit of the monitor Please disconnect the power cable or take off the battery under the following situations 1 If you do not operate this monitor for a period of time 2 If the power cable or power adaptor is damaged 3 If you operate this monitor by the methods different from this User Manual and cause unknown problems 4 If the monitor housing is broken Working Environment 1 Please don t lay this product on the unstable place 2 Please don t lay this product in hot cold or wet location Cleaning 1 Please clean the screen with dry and downy cloth or special LCD cleanser 2 Please do not press hard when cleaning the screen 3 Please do not use water or other chemical cleanser to clean the screen The chemical may damage the
12. enu language English Chinese selection 2 H POSITION Menu horizontal position 0 100 adjustment real time preview default value 50 center 3 V POSITION Menu vertical position 0 100 adjustment real time preview default value 50 center 4 DURATION Menu timeout setting Set a time in seconds in which the menu a eee will automatically quit if remains idle Default 10 seconds Range 5 seconds to 60 seconds OSD ADI OK EXIT 7 Title Settings Submenu Revolve OK button to select the letters and press OK to input Select SPACE to input space and DEL to delete the left letter Max 10 letters are supported After setting press MENU the system will save data to current user and quit menu The menu will automatically save and quit if it remains idle ADJ OK EXIT 8 Display Settings Submenu The DISPLAY settings submenu is to select the items to be displayed on screen when DISPLAY button is pressed Revolve OK to turn on off the items 1 INFO Including Input format aspect ratio underscan overscan zoom status 2 MARKER Safety mark 3 TITLE User edited title ADJ OK EXIT 9 FUNCTION KEY Settings Submenu The F KEY Settings Submenu is to define Function Keys on the front keyboard The DT X71F has 3 function keys F1 F2 and F3 The DT X71H and DT X71C has 2 function keys F1 and F2 The available function items of each model are 01 RATIO Aspect ratio switch
13. nd HDMI 16 ch audio meter Under HDSDI it displays 16 channels audio bars with mark and under SDSDI or HDMI it displays 2 channels audio bars with mark The audio bar is green and will turn yellow when audio exceeds 20dB and turn red when exceeds 10dB SDI timecode Under SDI input it can display the SMPTE timecode which is used extensively for synchronization and for logging and identifying material in recorded media Peaking focus assist red blue switch The Peaking focus assist function is to mark the sharpest edges of the image with red or blue color for users to check if the subjects are focused Zebra stripes Zebra Stripes are used to check if the image is over exposed or not by showing black and white lines on the monitor It is considered over exposed when luminance value exceeds 90 False color The false color is used to aid in the setting of camera exposure Under false color mode there s a false color key on the bottom of screen for reference The over exposed subjects above 101 IRE on the monitor will display as RED and the underexposed subjects will display as BLUE For correct exposed subjects it will display as green and pink Blue Only Under the Blue Only Mode only the blue pixels are used to generate the image because hue and saturation can be adjusted quicker and more accurately DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make
14. r will not be used for a period of time 3 IN Input signal selection Press IN and revolve the OK to select the input video signal 4 F1 User definable function key 1 5 FOCUS Peaking Focus Assist Press FOCUS once it will display the current peaking on off status Press FOCUS again to switch on RED line focus assist switch on BLUE line focus assist and switch off in turn 6 F COLOR False color Press F COLOR once it will display the current false color on off status Press F COLOR again to switch on off the false color mode 7 DISPLAY Display current settings Press Display to display safety mark title and the current input signal information 8 F2 User definable function key 2 9 F3 User definable function key 3 WAVEFORM 10 11 12 13 14 OFF OFF OFF OFF OFF WAVEFORM Display waveform Press WAVEFORM once it will display the waveform menu as Revolve OK to select a waveform display mode and turn it on The selected waveform will display on the screen VECTOR Display vector scope Press VECTOR to switched on off the Vector scope MENU Press to enter Menu OK Select and Apply Under menu system revolve OK to adjust settings and press to apply and out of menu system directly revolve OK to adjust volume TALLY Light Red Green and Yellow 3 color TALLY indicator Toy VW FB Fy Fy lt lt lt lt lt lt lt
15. the effective image scale full screen on the monitor G sensor auto flip Enable the G sensor auto flip the image will rotate automatically when monitor is bottom up User definable function keys There are 3 function keys on the monitor front panel and users could define the functions to the keys to achieve shortcut User editable video title User can edit a video title for the current camera and the title will display on the top of screen Front and Rear 3 color TALLY light 2 TALLY lights design to give live signals to people in front of the camera as well as the camera operator behind DT X71H New high resolution 7 LCD Panel 16 9 1024x600 16 77 million colors 900 1 contrast and H160 V160 viewing angle Multiple inputs 2 HD SD SDI 1 HDMI 1 Composite input and L R stereo audio Loop through outputs 1 HD SD SDI loop through output DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor Image Flip Set image to rotate by 180 User definable function keys There are 2 function keys on the monitor front panel that permit users to define shortcuts for the various functions User editable video title User can edit a video title for the current camera and the title will display on the top of screen Front and Rear 3 color TALLY light 2 TALLY lights design to give live signals to
16. ttery press the POWER and the power indicator is turned on and after 10 seconds the monitor will be switched on and get into normal working status Press the POWER again the indicator is turned off and monitor is switched off Remark Disconnect with power cable or take off the battery if the monitor will not be used for a period of time 3 4 5 6 7 8 9 10 11 12 13 VIDEO Press to switch the input signal to Composite video HDMI Press to switch the input signal to HDMI HD SDI1 Press to switch the input signal to the first HD SDI channel HD SDI2 Press to switch the input signal to the second HD SDI channel MENU Press to enter Menu F1 User definable function key 1 F2 User definable function key 2 RATIO 16 9 and 4 3 switch ZOOM Picture Zoom in Press ZOOM to switch ZOOM1 Canon DSLR scale zoom in and ZOOM2 pixel to pixel zoom in DISPLAY Display current settings Press Display to display safety mark title and the current input signal information OK Select and Apply Under menu system revolve OK to adjust settings and press to apply and out of menu system directly revolve OK to adjust volume 4 TALLY Light Red Green and Yellow 3 color TALLY indicator Rear view 1 2 3 4 5 9 8 7 6 1 DC 12V IN Connect with DC12V 4 pin XLR power adapter 2 TALLY Light Red Green and Yellow 3 color TALLY indicator 3 Battery mount Connect with JV
Download Pdf Manuals
Related Search