EM60 Dual Differential Thermometer
Contents
1. measurement is held Press the key again to cancel the hold function Press the key for more than 2seconds and the back light will be turned on The icon will be displayed Press the key again for more than 2 seconds and the backlight will be turned off The icon will disappear 9 5 UNIT key TYPE Press the UNIT key to select temperature units in F or To select thermocouple type When SHIFT is enabled press the TYPE key to select K type and J type thermocouple MODE 6 Hi Lo key Press the MODE key to alternate between maximum minimum measurement readout Hi Lo key The alarm Hi Lo temperature setting When the temperature is exceeds the Hi temperature setting or goes lower than the Lo temperature setting the alarm will continue to sound Set Hi Lo Limits When SHIFT is enabled press the Hi Lo key to enter the Hi Lo temperature setting A Use SHIFT key to select Hi or Lo setting B Use MODE or HOLD key to change alarm 10 setting C Use TI T2 or UNIT key to set temperature D Use SHIFT key to complete the setting NORMAL SHIFT Hi Lo Hi SHIFT Lo DISPLAY SETTING SETTING SHIFT ma ww Esc TE EA The Hi Lo temperature setting TYPE Hi Lo K 1300 2372F 200 C 328 F J 12007 21927 200 C 328 F 7 AUTO POWER OFF SETTING The instrument is factory set for Auto Power Off The meter will power itself off after 20 min2. T2 MAX MIN HOLD mode and K or J type thermocouple set Hi Lo alarm and store data refer to function keys 4 Press thalOLD key for more than 2 seconds to turn the back light on or off 5 Press the key for more than 2 seconds to turn the power OFF More operations are described in the Function Key directions below Function keys 4 SHIFT ON OFF ON OFF power ON OFF key Press once to turn the key power ON Press the key for more than 2 seconds to turn the power OFF SHIFT second function key Press the key to enable the second function of any key and a SHIFT icon will display on the LCD The function of key SHIFT disable MEM MODE UNIT SHIFT enable LIMIT Hi Lo TYPE 2 T1 T2 key Press the key to enable the T1 T2 function The T1 T2 icon will display on the LCD 3 MEM LIMIT MEM function Press the key to store the present key reading of T1 and T2 Up to five groups of data can be stored In the MEM mode press the T1 T2 or UNIT keys to view the recorded data up and down and press the 8 MODE or HOLD keys to select T1 or T2 When data is full 5 sets the OU icon will be displayed To clear memory press the MEM key for more than 2 seconds the CLER icon will be displayed Press LIMIT To enable the Hi Lo alarm function Press SHIFT then press the LIMIT key to turn the Hi Lo alarm ON or OFF HOLD 4 Light key When pressed icon will be displayed and the
3. 40 F 20 C to 60 C 0 to 80 RH 10 Dimensions 4 76 L x 2 36 W x 1 18 H 121mm L x 60mm W x 30mm H 11 Weight 6 35 oz app 180 g app 11 Accessories K type thermocouple wire 2 Lanyard 1 AAA Batteries 3 Users manual lilinstrument Description 1 Sensor cover 2 Thermocouple input jacks 3 LCD display 4 Function key Double ways thermocouple meter LCD Display 9 9 LIMIT SH HTN M CK f e 1 11 12 6 1 4 Symbol Designations 1 ON M Data Hold Indicator Indicates the high or low temperature setting Indicates the second function key Indicates type of thermocouple Measurement Display area Measurement Display area T1 T2 Maximum Minimum Indicator Indicates backlight ON Temperature units 10 Low Battery Indicator Operating Instructions NOTE After abrupt ambient temperature changes allow instrument temperature to stabilize for 20 minutes for accurate measurements 1 2 Press the ON OFF key to turn the unit on Plug one or both thermocouples into the inputs at the top of the instrument If there are no thermocouples 6 installed the instrument will display OL Otherwise the display will show T1 and or T2 identifying which thermocouple s is are installed 3 Press the function key to change temperature units select T1
4. EM60 DUAL INPUT THERMOMETER Sipe Users Manual 1 lilintroduction Thank you for purchasing the SUPCO Dual Input thermometer thermocouple Please take a few minutes to browse through this user manual before you begin to operate the meter to ensure that you are fully familiarized with how best to operate the meter as accurately and safely as possible This meter can match any standard K type or J type thermocouple sensor 1 1 Precautions safety measures To get the best performance from this meter please read this user s manual carefully and observe the detailed safety precautions 1 1 1 Maintaining the product Do not measure in high temperature high humidity locations When not using the instrument for a long time please remove the battery and avoid storing in high 2 temperature and high humidity Features 1 2 c 54 29 0 Display 4 digit LCD Display Resolution 0 1 F 0 1 C below 1832 1 1 above 1832 F Range K type 328 F to 2372 F 200 to 1300 C J type 328 F to 2192 F 200 C to 1200 C Accuracy 0 2 reading 2 F for 328 to 148 F 0 1 reading 1 4 F for 148 to 2372 F 0 2 reading 1 C for 200 to 100 C 0 1 reading 0 7 for 100 to 1300 Sample rate 1 time sec Auto power off 20 minutes app Low battery indicator Operating environment 32 F to 122 F 0 C to 50 C 0 to 80 RH 3 9 Storage environment 4 F to1
5. either expressed implied or statutory and is the only 13 warranty being issued herein Sealed Unit Parts Co Inc s liability in connection with its products is expressly limited to the repair or replacement of defective parts All other damages and warranties statutory or otherwise are being expressly excluded No representative of Sealed Unit Parts Co Inc has authority to change this warranty in any manner whatsoever No attempt to repair or promise to repair or improve any part covered by this warranty by any representative of this company shall be effective unless signed by a properly authorized officer of Sealed Unit Parts Co Inc Sealed Unit Parts Company Inc SUPCO 2230 Landmark Place Allenwood NJ 08720 USA WWW SUpco com info supco com
6. utes if no key is pressed 11 To cancel auto power off press the HOLD key until the LCD displays all icons and the buzzer sounds continuously Maintenance 1 CLEANING INSTRUCTIONS The meter may be wiped down with a wet sponge or cloth using a mild water based detergent NOTE This unit is not designed for complete submersion or washing in water 2 BATTERY REPLACEMENT Use the following procedure When the battery voltage drops below proper operation range the symbol will appear on the LCD display and the battery needs to be replaced Press the battery cover towards the arrowhead to open the battery cover co Replace the battery with three new AAA 1 5V 12 batteries Replace the battery cover WARRANTY Sealed Unit Parts Co Inc warrants that it will repair or furnish without charge a similar product to replace any product which within the specified warranty term after the date of sale by the Wholesaler is proved to the satisfaction of Sealed Unit Parts Co Inc to have been defective at the time it was sold Said warranty is in effect only when said item is used in accordance with the instructions and recommendations of Sealed Unit Parts Co Inc This warranty applies only to products which after shipment from the factory have not been altered changed repaired or treated in any manner whatsoever This warranty to repair or replace is the only warranty
Download Pdf Manuals
Related Search