Installation Guide: TST-600 and TST-602 Accessories
Contents
1. IR window facing up a Screws 4 a 06 32 x 3 16 with Nylon Washers Secure the bezel to the metal chassis box using the supplies screws and washers 8 Use the four supplied 06 32 x 3 16 screws with washers two on the left side and two on the right side to attach the bezel 9 Dock the TST 600 or TST 602 Refer to Docking the Touch Screen for details Uninstalling the TST 600 DSW If it is necessary to remove the TST 600 DSW after it has been installed complete the following steps in the order provided The only tool required is a 2 Phillips screwdriver 1 Undock the touch screen Refer to Undocking the Touch Screen for details 2 Push the TST 600 DSW mechanism backward into the box until it locks in place exposing the screws securing the bezel on the left and right sides 3 Remove the screws and washers two from the left side and two from right side which secure the bezel and gently remove the bezel from the TST 600 DSW 4 Remove the screws two from the top and two from the bottom which secure the TST 600 DSW to the back box 5 If necessary secure and label the attached cables before disconnecting them from the TST 600 DSW Hardware Hookup Make the necessary connections as called out in the illustration that follows this paragraph Apply power after all connections have been made When making connections to the TST 600 DSW use C2. 2 Slide the emergency latch release tool upward to engage the release latch The TST 600 DSW mechanism slides forward and the tab on the bottom of the docking fixture slides clear of the recess on the rear of the touch screen 3 The touch screen can now be removed from the TST 600 DSW by first pulling the bottom of the touch screen slightly forward and then lifting the touch screen upward off the tab on the top of the docking mechanism TST 600 FP AND TST 600 FP NB INSTALLATION Perform the following procedure to remove the existing bezel and install the new bezel onto the touch screen A 1 Phillips screwdriver is required Refer to the illustration below 1 Turn off the touch screen and then slide the battery switch on the rear to the off down position 2 Place the touch screen face down on a clean padded work surface 3 Remove the four screws that secure the front bezel to the touch screen and return the unit to its normal face up position Use care and hold the bezel against the touch screen If the bezel separates from the rest of the touch screen while rotating the unit to its normal position the internal parts of the touch screen may spill out Rear View Showing the Battery Switch and Screw Locations Screws Screws 4 When the touch screen is in its normal face up position unsnap the bezel and lift it from the touch screen 5 Position the new bezel over the exposed touch screen en
3. 600 DSW PMK TST 600 DSW MMK TST 600 DSW TMK Mud Mount Kit Accessory Trim Mount Kit Accessory Pre construction refers to framed walls prior to hanging drywall Post Construction Mounting Options for the TST 600 DSW and TST 600 or TST 602 1 aah MODEL DOCUMENT NUMBER Wall Mount Kit Mud TST 600 DSW WMKM 7457 Wall Mount Kit Trim TST 600 DSW WMKT 7456 1 Post construction refers to framed walls with drywall hung 2 Since the TST 600 DSW contains moving parts mounting it to a stud offers more support and is therefore highly recommended Although Crestron offers the post construction TST 600 DSW WMKM and TST 600 DSW WMKT mounting options a mouning option that is secured to a stud such as the TST 600 DSW BB or TST 600 DSW PMK is highly recommended NOTE There is also an international back box kit TST 600 DSW BBI available for the TST 600 DSW for installation in concrete and masonry Refer to the TST 600 DSW BBI Installation Guide Doc 7454 at www crestron com manuals If the TST 600 DSW BB or TST 600 DSW PMK is to be used and a TSW 600 DSW Docking Station is not available the installer can either leave the hole in the mounting surface open if permitted by local building codes or attach the cover plate supplied with the mounting kit to the mounting hole Installation To install the TST 600 DSW complete the following procedure in the order provided The only tool required is a 2 P
4. Crestron TST 600 and TST 602 Accessories Installation Guide amp CRESTRON Further Inquiries To locate specific information or resolve questions after reviewing this guide contact Crestron s True Blue Support at 1 888 CRESTRON 1 888 273 7876 or for assistance within a particular geographic region refer to the listing of Crestron worldwide offices at www crestron com offices To post a question about Crestron products log onto Crestron s Online Help at www crestron com onlinehelp First time users must establish a user account to fully benefit from all available features Future Updates As Crestron improves functions adds new features and extends the capabilities of the TST 602 DS TST 602 DSW TST 600 FP TST 600 FP NB and TST 600 IMCW additional information may be made available as manual updates These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision Check the Crestron website periodically for manual update availability and its relevance Updates are identified as an Addendum in the Download column Installation Guide DOC 7687A 2041540 12 14 Specifications subject to As of the date of manufacture the TST 600 DS TST 600 DSW and TST 600 IMCW have been tested and found to comply with specifications for CE marking change without notice Federal Communications Commission FCC Compliance Statement This device c
5. W is listed in the following table Supplied Hardware for the TST 600 DSW PART DESCRIPTION NUMBER Assembly Bezel with IR Wall Dock Black Assembly Bezel with IR Wall Dock Textured Black Assembly Bezel with IR Wall Dock White Silkscreen Assembly Metal Plate Aesthetic Black Silkscreen Assembly Metal Plate Aesthetic White Screw 04 40 x 3 16 Steel Flat Phil Black Screw 04 40 x 3 16 Steel Flat Phil Zinc Screw 06 32 x 1 1 2 Steel Pan Phil Mounting Screw 06 32 x 3 16 with Nylon Washer Emergency Latch Release 4504777 4507641 4507241 4505195 4507217 2007145 2007150 2007254 4509330 4507211 I oe DOR S Ree ee 1 These parts come with the TST 600 DSW B S Smooth Black 2 These parts come with the TST 600 DSW B T Textured Black 3 These parts come with the TST 600 DSW W S Smooth White Mounting Options The TST 600 DSW Docking Station and TST 600 or TST 602 Touch Screen install simply and cleanly into existing or newly constructed wall with an assortment of pre and post construction mounting options All mounting options are sold separately from the touch screen Refer to the following table for a complete list of mounting options and respective installation guides Pre Construction Mounting Options for the TST 600 DSW and TST 600 or TST 602 PRE CONSTRUCTION OPTION MODEL DOCUMENT NUMBER Back Box Kit Pre Construction Mount Kit TST 600 DSW BB TST
6. e mounted in a rack with other equipment using the four mounting holes on the corners of the interface module as shown in the following illustration TST 600 IMCW Rack Mount Exploded View Rack Rail AS S 1 Gang Electrical Box Not Included TST 600 IMCW Screws 2 06 32 x 1 Wall Plate with Hardware Not Included Assy Insert R g TST 600 IMCW Assy Insert Rack Mount Screws Not Included WARNING To prevent bodily injury when mounting or servicing this unit in a rack observe the following guidelines e When mounting this unit in a partially filled rack load the rack from the bottom to the top with the heaviest component at the bottom of the rack e Ifthe rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack Installing on a Level Surface To prepare the TST 600 IMCW to be mounted onto a level surface ensure the unit is attached to the surface mount bracket as shown in the following illustration TST 600 IMCW Bracket Mount Exploded View TST 600 IMCW Mounting Bracket Screws 2 06 32 x 3 16 Assy Insert o To lt P y P y M Y SS Hardware Hookup Make the necessary connections as called out in the following illustration Apply power after all connections have been made When making connection
7. he display screen until the TST 600 DSW mechanism locks into place and the touch screen is flush with the TST 600 DSW bezel When the mechanism locks into place the tab on the bottom of the docking fixture slides into the recess on the rear of the touch screen to secure it in place Undocking the Touch Screen In normal operation the TST 600 DSW unlatches the touch screen electrically via the control system program The control system program defines the particular touch screen button that will be used for unlatching When the touch screen is unlatched the docking mechanism slides forward and the tab on the bottom of the docking fixture slides clear of the recess on the rear of the touch screen The touch screen may then be removed from the TST 600 DSW by first pulling the bottom of the touch screen slightly forward and then lifting the touch screen upward off the tab on the top of the docking mechanism If the touch screen cannot release from the TST 600 DSW use the supplied emergency latch release tool to undock the touch screen with the following procedure 1 While standing directly in front of the TST 600 DSW insert the emergency latch release tool into the space between the right side of the touch screen and the TST 600 DSW bezel about 1 25 mm up from the bottom right corner all the way to the line marked on the tool Refer to the following illustration Using the Supplied Emergency Latch Release Tool
8. hillips screwdriver CAUTION Allow an air gap of at least 12 inches 305 mm in the wall cavity above and below the touch screen for heat dissipation NOTE The TST 600 DSW has been optimized for mounting in 5 8 16 mm drywall A thickness of 1 2 to 1 13 to 25 mm can be used without issue Thinner or thicker drywall causes issues with the installation of the product NOTE The following steps are performed only after the TST 600 DSW BB or TST 600 DSW PMK has been installed It is assumed the TST 600 DSW BB or TST 600 DSW PMK has been secured to the stud according to the instruction in the latest installation guides Doc 7455 and Doc 7453 respectively It is assumed that drywall is in place and a cutout for the TST 600 DSW and touch screen is made in the drywall The TST 600 DSW is shipped with the docking mechanism locked in its back position In order to make cable connections the mechanism must first be unlocked so it slides to the forward position To do this slide the release latch on the right side of the TST 600 DSW upward to release the mechanism The mechanism slides forward To locate the release latch refer to Undocking the Touch Screen 1 Remove the four screws holding the cover plate in place to gain access to the connectors on the TST 600 DSW TST 600 DSW Installation Cover Plate Removal Before
9. into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Industry Canada IC Compliance Statement CAN ICES 3 B NMB 3 B INTRODUCTION This document provides installation instructions for accessories that ship with either the TST 600 and TST 602 Wireless Touch Screens or the TST 600 WALL and TST 602 WALL Wall Mount Wireless Touch Screens For installation instructions refer to the section for each of the following accessories e TST 600 DS e TST 600 DSW e TST 600 FP and TST 600 FP NB e TST 600 IMCW TST 600 DS INSTALLATION The only connection to the TST 600 DS is via the fixed cable which is connected to the TO PANEL port on the included TST 600 IMCW Interface Module When connecting the TST 600 DS to the TST 600 IMCW consider the following e Use Crestron power supplies for Crestron equipment e The included cable cannot be extended Hardware Connection from the TST 600 IMCW to the TST 600 DS To TO PANEL Port on TST 600 IMCW NOTE The length of the connecting cable on the TST 600 DS is 9 feet 2 3 4 meters The length of the cable has been shortened for illustrative purposes in the diagram above NOTE The included cable mount ferrite bead FBTH 2 should be placed on the cable near the connector end TST 600 DSW INSTALLATION Supplied Hardware The hardware supplied with the TST 600 DS
10. mounting the unit into the wall remove the cover plate to access the connectors Once all cables are connected replace the cover plate 2 Hold the TST 600 DSW near the back box and connect the NET and LAN cables from the back box to the ports on the back of the unit 3 Replace the cover plate using the four screws from step 1 4 Place the TST 600 DSW into the back box or against the TST 600 DSW PMkK if using this instead of the back box and using the four supplied 06 32 x 1 1 2 screws two at the top and two at the bottom to attach the TST 600 DSW to the back box as shown in the following illustration TST 600 DSW Installation Secure to the Mounting Option NOTE Either the TST 600 DSW BB or TST 600 DSW PMK must be installed before installing the TST 600 DSW into the wall Secure the aesthetic plate to the docking station assembly with the four 4 included 04 40 x 3 16 screws Screws 4 06 32 x 1 1 2 5 Use the four supplied 04 40 x 3 16 flat head screws to attach the aesthetic plate to the front of the TST 600 DSW mechanism 6 Push the mechanism backward into the box until it locks in place exposing the screw holes on the left and right sides Refer to the following illustration 7 Install the bezel being careful to orient it with the IR window facing up Refer to the following illustration TS 600 DSW Bezel Installation Install the bezel with the
11. omplies with part 15 of the FCC Rules Operation is subject to the following conditions Crestron Electronics Inc 15 Volvo Drive Rockleigh NJ 07647 Tel 888 CRESTRON Fax 201 767 7576 www crestron com 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment
12. restron power supplies for Crestron equipment Hardware Connections for the TST 600 DSW 3 T3 f 5 aa e q lg NET gt 24 Vdc Power Input BES fk oO oO y LAN 10 BASE T 100 BASE TX Ethernet to LAN Docking the Touch Screen To dock the TST 600 or TST 602 perform the following procedure 1 Press the OPEN button located on the front of the TST 600 DSW to the right of the docking fixture The mechanism slides forward 2 Position the touch screen onto the TST 600 DSW at a slight angle to latch the top portion of the touch screen to the tab on the top of the docking fixture When the top portion is latched move the bottom of the touch screen backwards so the touch screen is flat against the docking fixture Magnets on the docking fixture contact the metal plates installed on the touch screen to secure the touch screen in place 3 Push the touch screen backward being careful not to touch t
13. s to the TST 600 IMCW use Crestron power supplies for Crestron equipment Hardware Connections for the TST 600 IMCW Front OS 0 a TO PANEL Connect to TST 600 DS TO PANEL Docking Station via 10 Pin RJ 50 Cable Provided with Docking Station PWR gt C PWR From DC Power Pack 24VDC 75A p O Kop Hardware Connections for the TST 600 IMCW Rear O GRISSTIRION LAN 10BASE T 100BASE TX e Ethernet to LAN 24 G 24 Vdc Power Input Product warranty can be found at www crestron com warranty The specific patents that cover Crestron products are listed at patents crestron com Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics Inc in the United States and or other countries Other trademarks registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Crestron disclaims any proprietary interest in the marks and names of others Crestron is not responsible for errors in typography or photography This document was written by the Technical Publications department at Crestron 2014 Crestron Electronics Inc
14. suring the bosses line up and mate with the enclosure 6 Gently snap the tabs next to the screen near the volume control and the 5 way thumbpad Refer to the following illustration Snap the Tabs Near Volume Control and the 5 Way Thumbpad 7 Hold the bezel against the touch screen and carefully rotate the entire touch screen onto its face once more 8 Reinstall the four screws to secure the bezel to the touch screen Tighten the screws being careful not to strip the threads 9 Reconnect the power and then slide the battery switch on the rear to the on up position TST 600 IMCW INSTALLATION The TST 600 IMCW can be installed in a 1 gang box it can be rack mounted or it can be mounted on any flat surface using the included mounting bracket Supplied Hardware The hardware supplied with the TST 600 IMCW is listed in the following table Supplied Hardware for the TST 600 IMCW PART DESCRIPTION NUMBER Assembly Insert Black 4509271 4509273 2016054 2003574 2013235 2007203 Assembly Insert White Metal Bracket 16 GA CRS Conn Plug 2 Pin SKT Single Row Screw 06 32 x 1 Flat Slot Screw 06 32 x 3 16 Pan Phil Installing in a 1 Gang Box To install the TST 600 IMCW in a 1 gang box mount the unit into the box as shown in the following illustration TST 600 IMCW in a 1 Gang Box Exploded View Mounting Surface t Rack Mounting The TST 600 IMCW can b
Download Pdf Manuals
Related Search