16” OUTDOOR MISTING FAN Model: SF
Contents
1. S T 16 OUTDOOR MISTING FAN Ki N OJ L ZN A y a N M EW 5sssess i w GM UN 73s eo l l w Kx SK W KG SS SPT ACHT Lh gt oO amp Model SF 1670M READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following WARNING this fan is supplied with a grounded plug and GFCI To reduce the risk of electrical shock make sure it is connected only to a PROPERLY grounded outlet DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUND PRONG OR GROUND FAULT UNIT For your personal safety the fan must be grounded The fan is equipped with a power supply with ground fault circuit interrupting device Removal or tampering of the power cord will void warranty Electric shock hazards may cause severe personal injury or death For your safety turn off the electrical power supply before installing moving or servicing your fan to avoid any possible electrical shock hazards Never make adjustments to the fan when power is on UNPLUG THE FAN WHEN NOT IN USE To reduce the risk of fire or electrical shock do not use this fan with any solid state speed control device This appliance has a 3 prong plug To reduce the risk of electrical shock this plug is intended to fit in an outlet only one way If2. When switched on fan will operate at speed 3 high for three seconds then return to preset speed of the remote OFF Press to turn unit off SPEED Press to select desired fan speed 1 Low 2 Medium and 3 High MODE Press to select fan mode Normal Natural and Sleep See page 7 for details o Normal mode o Natural mode unit automatically cycles between the three fan speeds o Sleep mode depending on the fan speed when mode is engaged unit will drop down one speed every 30 minutes until it reaches Low speed 1 Fan will remain operating at low until timer up manually turned off or settings changed SWING Press to select oscillation mode left right up down figure 8 or no oscillation TIMER Press to set timer in 30 minute increments up to 7 5 hours Using the Control Panel The same functions keys found on the remote can be found on the unit s control panel ON SPEED o Press to turn unit on Fan will start in Normal mode on speed 3 and switch to speed 1 after 3 seconds o Press again to select the desired fan speed 1 Low 2 Medium and 3 High The corresponding Speed indicator light will illuminate OFF Press to turn unit off MODE Press to select fan mode Normal Natural and Sleep Corresponding indicator light will illuminate see page 7 for details o Normal mode you can set desired fan speed o Natural mode unit automatically cycles between the three fan speeds o Sleep mode depending on the fan speed w
3. indoors WITHOUT THE MISTING FEATURE l RULES FOR SAFE OPERATION Never insert fingers or any other objects through the grill guard when fan is in operation Disconnect the fan when moving from one location to another Disconnect the fan when removing guards for cleaning Be sure fan is on a stable and flat surface when in operation DO NOT use when raining Rain may create electrical hazard READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire or electrical shock and injury to persons DO NOT use in a window GROUNDING INSTRUCTIONS This product must be grounded If it should malfunction or breakdown grounding provides a path with the least resistance of electric current to reduce the risk of electric shock This product is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of the equipment grounding conductor can result in a risk of electrocution Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the product If it does not fit the outlet have a proper outlet installed by a qualified electrician Do not use any type of adaptor with this product GROUND FAULT CIRCUIT INTERRUPTER GFCI PROTECTION T
4. This fan is equipped with an inline Ground Fault Circuit Interrupter built into the power we me supply cord This device provides additional protection from the risk of electric shock Se A Should replacement of the plug or cord become necessary use only identical replacement parts that include GFCI protection OSHA Required Safety Product INSTRUCTIONS Plug GFCI into a 120V power outlet Verify that the red LED indicator turns on This indicates power to the GFCI receptacles Press the TEST button and verify that the red LED indicator turns off Press and release the RESET button and verify that the red LED indicator turns on The GFCI is now ready to use Te WARNING e Ifthe GFCI fails to trip turn off when the TEST button is pressed or fails to reset turn on the device is defective and should be replaced e Ifthe GFCI tests properly without a load applied but trips each time a load is connected then the load has a ground fault condition and needs to be repaired DO NOT BYPASS THE GFCI IF THIS CONDITION OCCURS AN ELECTRICAL SHOCK MAY OCCUR CAUTION e This device is to be used on normal distribution systems 120V 15 amps 60Hz maximum e This GFCI is a safety device Do not use the test and reset buttons as on off switch e All Ground Fault Circuit Interrupters GFCI do not protect against electrical shock resulting from contact with both current carrying conductors of an electrical circuit e Do not connect any extens
5. and Check that filter is evenly seated in cap and re install Washer may be damaged and needs replacement Sediment rough hose edges or over tightening may damage the washer Leak at tube attachment In locations with hard water the use of a polyphosphate filter is recommended to remove sediment and lessen the effects of hard water Areas with hard water deposits The filter is to be attached directly to your hose bib before the swivel adaptor Polyphosphate filters should be replaced approximately after six months of use 10 Spl Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase it will be repaired free of charge This guarantee is subject to the following terms Sunpentown must be notified of the fault Proof of purchase must be presented to Sunpentown s nominated representative The warranty will be void if the product if modified misused or repaired by an unauthorized person The warranty after repair will not be extended beyond the original one year period All replacement parts will be new or reconditioned Parts which are replaced become the property of Sunpentown The warranty applies for the use of the product in the USA only What is NOT COVERED Warranty does not include freight charges Incidental or consequential damage caused by possible defects with this product Damage to product caused by improper po
6. dditional scrubbing of the nozzles with a stiff non metallic brush e After soaking shake the nozzles you should hear a rattling sound If none is heard gently tap the nozzle against a solid surface to loosen any obstruction If still no sound is heard the nozzle should be replaced IMPORTANT Never attempt to clear nozzles with pins nails or other metal objects as this can damage the misting orifice CAUTION There are no consumer serviceable parts inside this fan If you experience a problem please see warranty for information Please do not attempt to open the motor housing of the fan doing so may cause damage to the fan or personal injury as well as voiding your warranty To purchase replacement nozzles contact Sunpentown Customer Service at 800 330 0388 CARE amp STORAGE Turn off power and unplug unit before cleaning Use only a soft moistened cloth with a mild soap solution to clean the fan Do not immerse fan in water Do not use gasoline thinners or other chemicals to clean fan To dismantle for cleaning or long term storage follow the assembly instructions in reverse order The fan blade may be washed in warm water with a mild detergent Alternatively it may be wiped clean with a soft damp cloth Be sure it is completely dry before re fitting The front and rear grills stand and base can be cleaned with a soft brush or soft damp cloth For storage clean fan carefully as instructed and store in its original box o
7. hen mode is engaged unit will drop down one speed every 30 minutes until it reaches Low speed 1 Fan will remain operating at low until timer up manually turned off or settings changed SWING Press to select oscillation mode left right up down figure 8 or no oscillation Corresponding indicator light s will illuminate TIMER Press to set timer in 30 minute increments up to 7 5 hours Corresponding indicator light s will illuminate NOTE e Settings made by the remote are reflected on the unit s control panel However settings or changes made on the control panel will not reflect on the remote e lf fan is turned on with the remote fan will resume to last settings recorded by the remote If changes were made on the unit s control panel and fan was turned off Those changes will not reflect when unit is turned on again with the remote e If fan is turned on via the control panel fan will operate at factory default Normal mode speed 3 then speed 1 after 3 seconds NATURAL MODE PATTERN Natural Mode with High Speed 3 natural wind high speed high speed 6s 3s 6s 6s 6s 3s 6s 6s 386s 9s 6s 6s 6s 6s 6s 6s medium speed low speed off me an T 0s W lt gt ot T 96s 3s Gs 9s Natural Mode with Med Speed 2 natural wind medium speed ws 6 95 3s 383s 6s 6s 6s 3s 6s 9s 353s 6s 6s 6s 3s 6s 65 high speed a Ds medium speed low speed off Natural Mode with Low Speed 1 __ natura
8. ion cord longer than 100 feet to the GFCI output to avoid the possibility of nuisance tripping Test frequently and before each use to ensure proper operation by following operating instructions 1 to 5 DO NOT use where water may enter GFCI case DO NOT modify or immerse this device DO NO exceed electrical rating PARTS IDENTIFICATION _ pws ae GUARD NUT i eos E decorate reg UP _ poe decoratve plaste patiFRONN Ranai L Pi SWITCH tH uguse TAREN catiBACR i a i iii t EL on ___ BASE DECORATION RING CONTROL BODYIFRONT PT oeae ong DOWN j am E cms 8 ASSEMBLY INSTRUCTIONS 1 On the lower shaft pole locate and remove the screw from the top end of the shaft Insert shaft to main body align the screw openings on the main body to the one on the shaft Re fasten the screw E Main body ii Pole Pole lower shaft ower shar Sower Sher 2 Place the base on sturdy ground and set decorative base into the circular indentation lt Decorative base ring EE T A aioi _ i n EE a _ _ _ a _ 3 Place aluminum tube over lower shaft and insert shaft into base Gently lay unit on its side and secure the shaft to base with lock nut turn clockwise lt Main body Ti i4 Pole a TI lower shaft z ii i Aluminium ii tube pn y Loek nut e Grill and Blade A
9. l wind low speed high speed Gs 3s 6s 9s 6s 3s3s 9s 6s 6s 35 68 6s Gs 3s3s 6s 6s medium speed m im low speed off ma ae Ge OO T SLEEP MODE PATTERN In Sleep Mode the wind pattern duplicates that of Natural mode The only difference is that the unit will automatically drop one speed every 30 minutes until it reaches Low and remain there For example if unit is on High speed and enters Sleep mode fan will run on High Natural mode for 30 minutes drop to Medium Natural mode for the next 30 minutes and drop again to Low natural mode until turned off or timer up MISTING FEATURE Hose Installation e Insert screen washer into the hose adapter e Attach adapter to any standard garden hose or spigot The misting function on off will be controlled by your main water source e For your convenience you have the option to install the included on off valve which allows independent control to the misting function WARNING DO NOT USE MISTING FEATURE INDOORS Cleaning Clogged Nozzles e Turn fan off and unplug unit from power source e Gently tap the nozzles to loosen any sediments that may have accumulated e lf tapping does not clear the nozzle unscrew each nozzle and place in a container of vinegar or a household lime and scale remover for approximate 30 seconds Make sure to stir or shake the solution every few minutes to help loosen debris Heavier deposits may require longer soaking time and or a
10. r cover with plastic cloth Store in a clean dry place REPLACING THE FUSE WARNING Handle with care when replacing the fuse Be cautious of broken glass or metal te 4 5 The fuse is located on the side of the plug Use a tapered flat tipped tool such as a small screw driver to slide open the fuse cover Remove fuse carefully Insert the tip of your tool into fuse slot and pry on the fuse slowly and gradually do not over exert Replace only with fuse type 5A 125V Insert fuse into slot and use tool to gently press on each end Do not press on the glass tube but the copper cap at each end Push cover back in place DO NOT OPERATE APPLIANCE IF THE POWER CORD SHOWS ANY DAMAGE OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS WORKING ENTIRELY Important During the first few minutes of initial use you may notice a slight odor this is normal and will quickly disappear TECHNICAL SPECIFICATIONS SF 1670M Input voltage AC 120V 60Hz ee 65W 2223cfm max 16 5 base diameter x 45 high TROUBLESHOOTING NO DOWER Make sure unit is plugged into a live socket p Press RESET button on the GFCI plug Make sure threaded extension pole is firmly Fan is unstable secured into base do not use tools to tighten Make sure hose adapter is connected to garden hose or spigot and the valve is open Nozzles require cleaning replacement Please refer to page 8 Fan is not missing Unscrew the swivel adapter by h
11. ssembly A On the motor housing unscrew and remove the guard lock nut turn counter clockwise B Mount the rear grill to the motor housing with the handle in the upright position align the openings on the grill to the two pins on the motor at 12 o clock and 6 o clock position Replace and gently tighten the guard lock nut turn clockwise ia T C Insert blade onto motor shaft align the indentation to the cross bar on the motor shaft D Secure blade by screwing on the blade cap turn counter clockwise E Attach the front grill with the water hose at 6 o clock position first hook the top clip to the rear grill then snap bottom into place The screw and clip located at the bottom of the front grill may have come loose please check and re fasten if necessary CAUTION All assembly and adjustments must be made when fan is turned off and unplugged from the electrical socket Place fan on a level surface before plugging into electrical socket This product is not for commercial use OPERATING INSTRUCTIONS Using the Remote Memory function The remote will remember your last settings after power off and resume fan to those settings when turned on again fan speed wind mode and oscillation mode for the exception of timer setting which will be cleared The LED display will go into sleep mode after 30 seconds of inactivity Press any button to reactivate LED display ON Press to turn unit on Note
12. t contact a qualified electrician Do not attempt to defeat this safety feature If replacement of the plug is needed use only identical replacement parts 17 Only use a 14 AWG 3 prong grounded extension cord with this fan 18 Use the fan only for the specific purpose outlined in this instruction information 19 Do not operate fan until fully assembled 20 Ensure the correct voltage is being used prior to plugging in your fan 120V AC electrical outlet 21 Do not immerse fan or expose fan to any form of liquid 22 Avoid contact with all moving parts Never insert your fingers pencils or other objects through the fan grill during operation 23 Place your fan on a stable and level surface to avoid tipping or being knocked over accidentally 24 Do not operate the fan directly adjacent to curtains plants window covering etc to avoid accidental entanglement 25 While your fan is tolerant to exposure of most weather situations we recommend that you bring the fan indoors or to a covered location during periods of extreme cold snow or rain 26 Always keep your fan covered when not in use to prevent excessive exposure to moisture and sun 27 Do not submerge your fan under water and keep a safe distance from pools outside water features or irrigation sprinklers 28 To avoid potential fire hazards never place your fan or its electrical cord under rugs or carpeting DORNO le a This fan is intended for outdoor use but may be used
13. the plug does not fit in the outlet contact a qualified electrician Do not attempt to bypass this procedure 1 Use this fan only as described in this manual Other uses not recommended may cause fire electric shock or injury to persons This product is intended for household use ONLY and not for commercial industrial or outdoor use The fan must be grounded To protect against electric shock do not immerse unit plug or cord in water or spray with liquids Close supervision is necessary when any appliance is used by or near children Unplug fan from outlet when not in use when moving from one location to another or before cleaning Avoid contact with moving parts Do not operate in the presence of explosives and or flammable fumes Do not place fan or any parts near an open flame cooking or heating appliance 0 Do not operate fan with a damaged cord plug or after the fan malfunctions or has been dropped or damaged in any manner 11 Do not let cord hang over the edge of a table or counter or let it touch hot surfaces 12 To disconnect grip plug and pull from wall outlet Never yank on cord 13 Always use on a level surface 14 Do not hang or mount fan on a wall or ceiling 15 Do not operate without fan grills properly in place 16 This appliance has a GFCI plug with ground pin To reduce the risk of electric shock this plug is intended to fit in a grounded outlet only one way If the plug does not fit fully in the outle
14. wer supply voltage accident fire floods or acts of nature Failure of product resulting from unauthorized modifications to the product Improper installation or failure to perform the necessary maintenance This GUARANTEE is in addition to your Statutory Rights SUNPENTOWN INTERNATIONAL INC 14625 Clark Avenue City of Industry CA 91745 Tel 626 336 2299 Fax 626 336 7116 service sunpentown com www sunpentown com 11
Download Pdf Manuals
Related Search