Sun Blade T6300 Server Module Installation Guide
Contents
1. Powering On the Server Module on page 10 Installing an Operating System on a Hard Drive on page 10 Handling the Module Electronic equipment is susceptible to damage by static electricity Use a grounded antistatic wriststrap footstrap or equivalent safety equipment to prevent electrostatic damage ESD when you install the Sun Blade T6300 server module Caution To protect electronic components from electrostatic damage which can permanently disable the system or require repair by Sun service technicians place components on an antistatic surface such as an antistatic discharge mat an antistatic bag or a disposable antistatic mat Wear an antistatic grounding strap connected to a metal surface on the chassis when you work on system components Installing the Module Into the Chassis This section contains instructions for installing the module into the chassis Note The following instructions assume that you have connected a terminal to a terminal server connected the terminal server to the chassis and set up the network management port on the chassis If not refer to the Sun Blade T6000 Chassis Installation Guide for instructions on how to set up the network management port w To Install the Module 1 Ensure that you have the MAC address and serial number from the labels on the shipping container and server module 2 Locate the desired slot in the chassis 3 Remove the filler panel if applicabl2. 2007 Front Panel Features This section contains an illustration of the front panel along with descriptions of the features Locator LED Ready to Remove LED Service Action Required LED OK LED Power button Reset button nonfunctional c HOO me GO t i Universal connector port Drive Readv to Remove LED Fault LED not used Drive OK LED FIGURE 1 1 Sun Blade T6300 Server Module Front Panel Chapter 1 Before You Begin the Installation 3 Dongle Cable You can order a dongle cable with the Sun Blade T6300 server module or you can use the dongle cable that shipped with the Sun Blade T6000 chassis FIGURE 1 2 shows the connections on the dongle cable Virtual console DB9 serial Video not supported FIGURE 1 2 Dongle Cable Connections 4 Sun Blade T6300 Server Module Installation Guide April 2007 Remote Manageability With ALOM CMT The Sun Advanced Lights Out Management ALOM CMT feature is a system controller that enables you to remotely manage and administer the Sun Blade T6300 server module The ALOM CMT software is preinstalled as firmware and initializes as soon as you apply power to the system You can customize ALOM CMT to work with your particular installation ALOM CMT enables you to monitor and control your server over a network or by using a dedicated serial port for connection to a terminal or terminal server ALOM CMT provides a
3. February 2005 m Building a JumpStart Infrastructure by Alex Noordergraaf Enterprise Engineering Sun BluePrints OnLine April 2001 You can obtain these documents from the following site http www sun com blueprints 12 Sun Blade T6300 Server Module Installation Guide 7 April 2007
4. command line interface that you can use to remotely administer geographically distributed or physically inaccessible machines In addition ALOM CMT enables you to run diagnostics such as POST remotely that would otherwise require physical proximity to the server s serial port You can configure ALOM CMT to send email alerts of hardware failures hardware warnings and other events related to the server or to ALOM CMT The ALOM CMT circuitry runs independently of the server using the server s standby power Therefore ALOM CMT firmware and software continue to function when the server operating system goes offline or when the server is powered off ALOM CMT monitors the following Sun Blade T6300 server module components CPU temperature conditions Disk drive status Fan speed and status Voltage conditions For information about configuring and using the ALOM system controller refer to the Advanced Lights Out Management ALOM CMT v1 3 Guide 819 7981 Chapter 1 Before You Begin the Installation 5 6 Sun Blade T6300 Server Module Installation Guide April 2007 CHAPTER 2 Installation and Configuration After you have familiarized yourself with the features and components of the Sun Blade T6300 server module use the instructions in this chapter to install the server into the chassis This chapter contains the following topics Handling the Module on page 7 Installing the Module Into the Chassis on page 8
5. d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface utilisateur graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconnait les efforts de pionniers de Xerox dans la recherche et le derelo pement du concept des interfaces utilisateur visuelles ou graphiques pour l industrie informatique Sun d tient une license non exclusive de Xerox sur l interface utilisateur graphique Xerox cette licence couvrant galement les licenci s de Sun impl mentant les interfaces utilisateur graphiques OPEN LOOK et se conforment en outre aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA LIMITE DE LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALIT MARCHANDE L APTITUDE UNE UTILISATION PARTICULI RE OU L ABSENCE DE CONTREFA ON LD com CA Adobe PostScript Contents Preface v Before You Begin the Installation 1 Hardware Overview 1 Physical Specifications 2 Environmental Requirements 2 Front Panel Features 3 Dongle Cable 4 Remote Manageabili
6. s Sun Microsystems Inc poss de les droits de propri t intellectuels relatifs la technologie d crite dans ce document En particulier et sans limitation ces droits de propri t intellectuels peuvent inclure un ou plusieurs des brevets am ricains list s sur le site B http www sun com patents un ou les plusieurs brevets suppl mentaires ainsi que les demandes de brevet en attente aux les tats Unis et dans d autres pays Ce document et le produit auquel il se rapporte sont prot g s par un copyright et distribu s sous licences celles ci en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Tout logiciel tiers sa technologie relative aux polices de caract res comprise est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit peuvent d river des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux tats Unis et dans d autres pays licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun docs sun com OpenBoot Java Sun Blade J2EE JumpStart Sun BluePrints et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans
7. NS R SUN microsystems Sun Blade T6300 Server Module Installation Guide Sun Microsystems Inc www sun com Part No 820 0275 10 April 2007 Revision A Submit comments about this document at http www sun com hwdocs feedback Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology fiat is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at http www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the s produtt may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo docs sun com r Java Sun Blade J2EE JumpStart Sun BluePrints and S
8. e 4 Attach the dongle cable to the server module 5 Attach an serial cable from the terminal server to the virtual console connector on the dongle cable You must connect the terminal server to the dongle cable before you insert the server module so that you can see the boot messages for the ALOM CMT software 6 Position the server module vertically so that the ejectors are on the right The following illustration shows the server module being inserted into the chassis 8 Sun Blade T6300 Server Module Installation Guide April 2007 FIGURE 2 1 Inserting the Sun Blade T6300 Server Module Into the Chassis 7 Push the server module into the slot until the module is about two inches from the chassis front 8 Push the ejectors down until they snap into place The server module goes into standby mode and the ALOM CMT system controller initializes as soon as you insert the server module into the chassis Chapter 2 Installation and Configuration 9 Powering On the Server Module After the system controller boots the system controller login prompt is displayed on the serial console Use the instructions in this section to log in to the system controller and to power on the server module v To Power On the Server Module 1 Log in to the system controller as the default admin user 2 Press Enter at the password promt By default the server module is shipped with no password for the admin account Before you power
9. gigabit Ethernet controller One SAS SATA controller One to four SAS SATA drives optional Two USB ports connected to dongle cable the dongle cable is optional One DB9 port connected to the dongle cable One RJ 45 serial virtual console port connected to the dongle cable Physical Specifications The Sun Blade T6300 server module is approximately 12 6 x 19 5 inches in a 1U form factor The server module plugs in to a 10U chassis The chassis provides cooling through six redundant fans and 12V power to each module In addition to 12V power the chassis provides 3 3 VAUX to each module to power the local FRU ID EEPROM This power enables the chassis management module CMM to query each module slot prior to 12V and fan application to validate that there is sufficient power and cooling to support the number and type of modules installed in the chassis Environmental Requirements TABLE 1 1 includes the environmental requirements that are specific to the Sun Blade T6300 server module TABLE 1 1 Sun Blade T6300 Server Module Environmental Requirements Condition Requirement Operating temperature 5 C to 35 C noncondensing Nonoperating temperature 40 C to 65 C Operating humidity 10 to 90 noncondensing 27 C max wet bulb Nonoperating humidity 93 noncondensing 38 C max wet bulb Operating altitude 3000 meters at 35 C Nonoperating altitude 12 000 meters 2 Sun Blade T6300 Server Module Installation Guide April
10. les new words or terms Read Chapter 6 in the User s Guide words to be emphasized Replace command line variables with real names or values These are called class options You must be superuser to do this To delete a file type rm filename The settings on your browser might differ from these settings Sun Blade T6300 Server Module Installation Guide April 2007 Related Documentation The documents listed as online are available at http www sun com documentation Application Title Part Number Late breaking news Sun Blade T6300 Server 820 0278 Module Product Notes Administration Sun Blade T6300 Server 820 0277 Module Administration Guide Service Sun Blade T6300 Server 820 0276 Module Service Manual Safety and Sun Blade T6300 Server 820 0279 compliance Module Safety and Compliance Manual ALOM Advanced Lights Out 819 7981 Management ALOM CMT v1 3 Guide Format HTML and PDF HTML and PDF HTML and PDF HTML and PDF HTML and PDF Location Online Online Online Online Online Preface vii Documentation Support and Training Sun Function URL Documentation http www sun com documentation Support http www sun com support Training http www sun com training Third Party Web Sites Sun is not responsible for the availability of third party web sites mentioned in this document Sun does not endorse and is not responsible or liable for any conte
11. nt advertising products or other materials that are available on or through such sites or resources Sun will not be responsible or liable for any actual or alleged damage or loss caused by or in connection with the use of or reliance on any such content goods or services that are available on or through such sites or resources Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions You can submit your comments by going to http www sun com hwdocs feedback Please include the title and part number of your document with your feedback Sun Blade T6300 Server Module Installation Guide part number 820 0275 10 viii Sun Blade T6300 Server Module Installation Guide April 2007 CHAPTER 1 Before You Begin the Installation This chapter includes general information to help you become familiar with the hardware and software features of the Sun Blade T6300 server module This chapter contains the following topics Hardware Overview on page 1 Physical Specifications on page 2 Environmental Requirements on page 2 Front Panel Features on page 3 Dongle Cable on page 4 Remote Manageability With ALOM CMT on page 5 Hardware Overview The Sun Blade T6300 server module includes the following hardware features One 6 or 8 core 32 thread CPU up to 1 4 GHz Eight DIMM slots that support up to 32 Gbytes of memory One dual
12. olaris are trademarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees viho implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements U S Government Rights Commercial use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara Californie 95054 Etats Unis Tous droits r serv
13. on the server module you should set the password with the password command 3 Use the password command to set the admin password sc gt password new password 4 Issue the poweron c command You see an sc gt alert message on the system console This indicates that the system has reset After you issue the poweron command the CPU and memory controllers initialize and eventually the OpenBoot PROM firmware initializes After a number of system messages you will see the ok prompt Installing an Operating System on a Hard Drive The basic configuration of the Sun Blade T6300 server module ships with or without empty hard drives If you ordered an optional hard drive and want to install the Solaris OS on the hard drive in slot 0 you must install the operating system from your network 10 Sun Blade T6300 Server Module Installation Guide 7 April 2007 For instructions on how to install the operating system from the network refer to the Solaris 10 6 06 Installation Guide Network Based Installations You can obtain this guide at http docs sun com JumpStart Server Installation You can use a JumpStart server to install the OS A JumpStart server consists of several components m Install client The target system to be installed or upgraded m Boot server The network providing a failsafe operating system to the installing client The boot image is architecture independent providing basic operating system
14. services to all hardware supported by that operating system release The Boot Server provides RARP TFTP and bootparam services Configuration server A system that helps client systems determine unique profile information Partition sizes lists of software components to install begin and finish scripts and more are specified in a profile served by the configuration server m Install server The source of the software packages to be installed on the client Note The boot server configuration server and install server can be one server They do not need to be physically separate servers JumpStart Server Configuration Specific instructions on how to configure a JumpStart server are out of the scope of this document However configuring the JumpStart server consists of the following tasks 1 Load the Solaris OS Create the configuration server Create the configuration files me ON Verify the configuration file syntax 5 Share the installation directory Chapter 2 Installation and Configuration 11 6 Start the NFS server 7 Configure the client access The configuration and use of the JumpStart server depends on the configuration of your network For a full explanation of these steps and instructions on how to configure the JumpStart server refer to the following documents m Configuring JumpStart Servers to Provision Sun x86 64 Systems by Pierre Reynes Network Systems Group Sun BluePrints OnLine
15. ty With ALOM CMT 5 Installation and Configuration 7 Handling the Module 7 Installing the Module Into the Chassis 8 v To Install the Module 8 Powering On the Server Module 10 w To Power On the Server Module 10 Installing an Operating System on a Hard Drive 10 JumpStart Server Installation 11 JumpStart Server Configuration 11 iv Sun Blade T6300 Server Module Installation Guide April 2007 Preface This guide includes general information about the Sun Blade T6300 server module and instructions for installing the server module into the Sun Blade T6000 chassis Using UNIX Commands This document might not contain information about basic UNIX commands and procedures such as coping files listing directories and configuring devices Refer to the following for this information m Software documentation that you received with your system m Solaris Operating System documentation which is at http docs sun com Shell Prompts Shell Prompt C shell C shell superuser Bourne shell and Korn shell Bourne shell and Korn shell superuser machine name machine name vi Typographic Conventions Typeface Meaning Examples AaBbCc123 The names of commands files Edit your login file and directories on screen Use 1s a to list all files computer output You have mail AaBbCc123 What you type when contrasted su with on screen computer output password AaBbCc123 Book tit
Download Pdf Manuals
Related Search