Sun Enterprise 450 Server Internal RAID Storage Option Installation
Contents
1. Caution UltraSCSI data cables are fragile and should be handled with care 1 Connect the C cable Chapter2 Installing the Internal RAID Storage Option 15 If you are installing the lower 8 disk backplane connect the PC cable to connector P0500 on the 4 slot backplane and to connector P0600 on the 8 disk backplane 16 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 If you are installing the upper 8 disk backplane connect the cable to connector P0601 on the lower 8 disk backplane and to connector P0600 on the upper 8 disk backplane Chapter 2 Installing the Internal RAID Storage Option 17 2 Connect the 8 slot UltraSCSI power cable to the backplane at connector J0101 Make sure that the tab on the bottom of the connector snaps into place N Bj m 4 7 Im f 7 UT 7 47 3 Connect the other end of the 8 disk UltraSCSI power cable to the power distribution board m If you are installing the lower 8 disk backplane use connector J0304 on the power distribution board m If you are installing the upper 8 disk backplane use connector J0303 on the power distributio2. See Reconfiguring and Rebooting the System on page 24 What Next m If this is the first SRC P Controller that you installed in your server the next step is to install the software necessary to run the SRC P Controller See the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide and the documentation supplied with your controller software m If you have already installed the software for a different SRC P Controller you are ready to configure drive arrays See How to Create an Array in the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide Note When you install a new SRC P Controller the controller will automatically initiate the initial calibration cycle for the battery The calibration cycle requires approximately 24 hours to complete During the calibration cycle the SRC P Controller cache is operating in Write through mode and should not be used for performance testing When the process is completed the battery module will be ready to provide backup protection and the controller will automatically switch to Write back mode See the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide for more information 28 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 APPENDIX A Specifications This appendix provides a functional description and a reference for physical performance electrical and environmental specifications Func
3. and other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements Federal Acquisitions Commercial Software Government Users Subject to Standard License Terms and Conditions DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2000 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 Etats Unis Tous droits r serv s Ce produit ou document est distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bai
4. 64 bit PCI 63 0 32 bit 64 bit PCI 10 pf maximum 16 bit single ended SCSI Yes No Yes Appendix A Specifications 31 Environmental Specifications TABLE A 4 Environmental Specifications Condition Operating Specification Storage Specification Temperature 10 C to 40 C 0 C to 40 C Relative humidity 10 90 non condensing 1096 9096 non condensing Altitude 3000 meters 10 000 feet 32 Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000
5. Storage Option Installation 9 10 First Time Installation Information Installing the Sun Enterprise 450 Server Internal RAID Storage option is one step in the SRC P Controller installation process You need to complete all of the steps in TABLE 1 5 to fully install your storage option TABLE 1 5 First Time Installation Steps Task 1 Review the features of the SRC P Controller and read the general information 2 Verify that you have received all of the parts you have ordered 3 Back up the data on the disks if necessary 4 Install the SRC P Controller card into the server 5 Install the software and configure RAID arrays 6 Restore data to disks if necessary For Information See This chapter Kit Contents on page 4 of this guide AnswerBook2 online documentation for the Solaris software environment Installing the SRC P Controller Card on page 12 of this guide or Upgrading an 8 Bay Storage Expansion Option on page 27 if you are upgrading from an 8 bay storage option The installation document included with the SRC P Controller software and the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide AnswerBook2 online documentation for the Solaris software environment Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 CHAPTER 2 Installing the Internal RAID Storage Option This chapter describes how to install the i
6. and configuring devices See one or more of the following for this information m Solaris Handbook for Sun Peripherals m AnswerBook2 online documentation for the Solaris operating environment m Other software documentation that you received with your system vii Typographic Conventions Typeface AaBbCc123 AaBbCc123 AaBbCc123 Meaning The names of commands files and directories on screen computer output What you type when contrasted with on screen computer output Book titles new words or terms words to be emphasized Command line variable replace with a real name or value Examples Edit your login file Use 1s a to list all files You have mail oo su Password Read Chapter 6 in the User s Guide These are called class options You must be superuser to do this To delete a file type rm filename Shell Prompts Shell C shell C shell superuser Bourne shell and Korn shell Bourne shell and Korn shell superuser Prompt machine names machine names viii Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 Related Documentation The following documents contain topics that relate to information in this guide TABLE P 1 Related Documentation Title Part Number Ultra Enterprise 450 Server Owner s Guide 805 0429 Sun StorEdge SRC P Intelligent SCSI RAID Controller 806 4148 User s Gui
7. the Solaris software environment Note You will need to refer to the Ultra Enterprise 450 Server Owner s Guide to complete the following tasks 2 Power off the system See How to Power Off the System 3 Tum off any peripheral devices attached to the server 4 Remove the right side panel See How to Remove the Right Side Panel 5 Remove the left side panel See How to Remove the Left Side Panel 6 Attach the antistatic wrist strap to your wrist and to a metal component on the server chassis 12 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 7 Remove the disk fan tray assembly See How to Remove the Disk Fan Tray Assembly 8 Unpack the SRC P Controller and place it on an antistatic surface 9 Insert the SRC P Controller into the appropriate slot on the main logic board You can install the SRC P Controller in PCI slots 1 through 7 only The SRC P Controller requires a 64 bit PCI slot a Remove the filler panel for the PCI slot you intend to use Remove the Phillips screw that secures the PCI filler panel to the rear panel b Align the left side of the card with the appropriate opening on the back panel At the same time insert the bracket on the right side of the card into the corresponding groove on the CPU cage c Push the card securely into the slot d Secure the SRC P Controller faceplate to the back pane
8. SS amp SUN microsystems oun Enterprise 450 Server Internal RAID Storage Option Installation Guide Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 U S A 650 960 1300 Part No 805 6765 11 September 2000 Revision A Send comments about this document to docfeedback sun co Copyright 2000 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 U S A All rights reserved This product or document is distributed under licenses restricting its use copying distribution and decompilation No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the product may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo AnswerBook2 docs sun com Sun Enterprise Sun Enterprise SYMON Sun StorEdge SRC P Intelligent SCSI RAID Controller Solstice DiskSuite OpenBoot SunVTS OpenWindows and Solaris are trademarks registered trademarks or service marks of Sun Microsystems Inc in the U S and other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S
9. Sun Enterprise 450 host server meets the following hardware and software requirements TABLE 1 2 System Requirements Component Description Software The operating environments supported are Solaris 2 6 Solaris 7 and later compatible operating environments Host system Sun Enterprise 450 server Maximum SRC P Six cards Controller cards PCI slot selection The SRC P Controller requires a 64 bit PCI slot On a Sun Enterprise 450 server use PCI slots 1 through 7 only Power requirements Two power supply units must be installed in the server General Information The next table provides hardware configuration information See Appendix A for specification information Chapter 1 Sun Enterprise 450 Server Internal RAID Storage Option Installation 7 TABLE 1 3 General Information Component Description Target devices Internal Disk Drives Each internal channel supports four internal disk drives One SRC P Controller card can support 12 internal disk drives Two 8 disk storage options are required to support the maximum internal disk drives External Devices Each card has three external connectors that can be used to support up to 36 external devices For each external storage device you need a 2m cable ordered separately The controller can support the following external drives if internal disks are not connected to that internal channel Sun StorEdge MultiPack 6 Sun StorEdge MultiPack 12 SCSI IDs and I
10. ance calibration Features All SRC P Controllers include the following features PCI Local Bus Rev 2 1 compliant 12 28 inch 31 19 cm long card 64 bit PCI bus 33 MHz clock speed High performance RISC processor Universal dual voltage signaling 3 3V and 5V Three external and three internal 68 pin SCSI connectors that are Fast Wide and Ultra Wide capable and that can support external single ended UltraSCSI disks SCSI data transfer rates of up to 40 Mbytes sec peak throughput per channel at a 20 MHz bus clock rate One 64 Mbyte onboard ECC write cache memory module Replaceable battery module that provides a backup time of 48 hours for 64 Mbyte cache Support for RAID levels 0 1 5 1 0 and 5 0 Support for hot spares hot plug disks and transparent drive rebuild Tunable cache parameters Self test capability Controller firmware that resides onboard in flash PROM and that can be upgraded without replacing any hardware chips Graphical and command line management interface Chapter 1 Sun Enterprise 450 Server Internal RAID Storage Option Installation 3 4 Kit Contents Your system may be configured to order with a RAID storage option already installed at the factory or you may order one of the option kits listed below Check that you ve received all of the parts you ordered Contact Sun Microsystems or your distributor reseller if you are missing anything TABLE 1 1 Option Kit Contents Option Kit and Related Op
11. cal 3 channel configuration Voltage 3 3V 5 Ripple and noise 50 mv peak to peak max Physical Dimensions TABLE A 2 Physical Dimensions Dimension Measurement Length of SRC P Controller with expansion card and 12 28 in 31 19 cm battery backup unit Width of SRC P Controller card 4 2 in 10 67 cm Length of basic SRC P Controller card 10 25 in 26 03 cm measurement does not include length of expansion card and battery backup unit Component height not including PCB Primary component side 0 570 in 14 48 mm Back side 0 105 in 2 67 mm 30 Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 TABLE A 2 Dimension Physical Dimensions Continued Measurement Length of expansion card daughter card Width of expansion card Length of battery module Width of battery module 5 575 in 141 6 mm 3 46 in 81 3 mm 4 475 in 113 7 mm 3 875 in 98 4 mm Performance Specifications TABLE A 3 Feature PCI clock PCI data burst transfer rate SCSI synchronous transfer rate SCSI asynchronous transfer rate SCSI transfer size PCI data address lines PCI modes Capacitance per PCI signal line SCSI interface SCSI bus parity SCSI 8 bit devices SCSI 16 bit devices Performance Specifications Specification 16 33 MHz 132 Mbytes sec 32 bit PCI 264 Mbytes sec 64 bit PCI 40 Mbytes sec Ultra Device dependent 64K blocks
12. de Sun StorEdge MultiPack Installation 805 3953 Sun StorEdge MultiPack Storage Guide 805 3955 Sun StorEdge MultiPack User s Guide 805 3954 Accessing Sun Documentation Online The web site enables you to access a select group of Sun technical documentation on the Web You can browse the docs sun com archive or search for a specific book title or subject at http docs sun com Ordering Sun Documentation Fatbrain com an Internet professional bookstore stocks select product documentation from Sun Microsystems Inc For a list of documents and how to order them visit the Sun Documentation Center on Fatbrain com at http www fatbrain com documentation sun Preface ix Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions You can email your comments to Sun at docfeedback sun com Please include the part number 805 6765 11 of your document in the subject line of your email x Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 CHAPTER 1 Sun Enterprise 450 Server Internal RAID Storage Option Installation The Sun Enterprise 450 internal RAID storage option consists of a Sun StorEdge SRC P Intelligent SCSI RAID Controller an 8 disk backplane and the internal cables necessary to connect the SRC P Controller to the 8 disk backplane This guide describes how to m Install th
13. e internal RAID storage option into a Sun Enterprise 450 server m Upgrade an 8 bay storage expansion option to an internal RAID storage option After you have completed the procedures in this guide see the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide for information about software installation and array configuration See First Time Installation Information on page 10 for a list of the tasks required to completely install the SRC P Controller About the SRC P Controller The SRC P Controller is a host based three channel UltraSCSI RAID controller card with a 64 bit PCI system interface and a dedicated processor The idea of RAID redundant array of independent disks is to combine multiple disk drives into an array of drives that provides better performance and more data protection than a single large drive The server sees the array as a single logical storage unit The SRC P Controller improves performance over software based RAID because it off loads RAID processing from the server CPU to the processor on the SRC P Controller card Fault tolerance for data protection is provided by different types of RAID architecture RAID levels 1 5 1 0 and 5 0 provide disk fault tolerance methods to protect data from being lost in the event of a hardware failure Each RAID level offers different trade offs in fault tolerance features and performance In addition RAID 0 offers no fault tolerance but it does provide
14. e system can properly recognize the new SRC P Controller you must verify that the card is installed correctly reconfigure the system and reboot the system 1 Power on the system See How to Power On the System in the Ultra Enterprise 450 Server Owner s Guide 2 When the system banner is displayed on the monitor immediately enter the Stop a sequence on the Sun keyboard If you are using an alphanumeric terminal instead of a monitor press the Break key on the terminal s keyboard 3 Use the show devs command to verify that the SRC P Controller is included in the list of system devices When the ok prompt is displayed enter the following command scsis identifies the SRC P Controller The listing should include a line similar to the following pci84 4000 pciQ84 scsisQ4 scsiQO If the SRC P Controller is not listed check that the card is properly seated Reinstall the card if necessary 24 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 4 Enter the following command to perform a reconfiguration boot ok boot r This command rebuilds the device trees for the system incorporating any newly installed options so that they can be recognized by the system After the reconfiguration boot has successfully completed the system prompt should be displayed What Next m If this is the first SRC P Controller that you installed in your server the next step is to install the software nece
15. high I O performance For additional data protection hot spare drives are supported Should an active drive fail the hot spare drive assigned to the array replaces it and the data is automatically redirected to the hot spare drive The SRC P Storage Manager which is a graphical user interface GUI and a command line management interface are included for RAID configuration diagnostics and event reporting The SRC P Controller automatically determines a RAID level and stripe size for your array based on your requirements for capacity security and performance You can also manually select a specific RAID level through the GUI The SRC P Controller uses read ahead caching to reduce disk access time and improve performance The controller automatically tallies I O operations in cache RAM for analysis of storage subsystem I O loading You can view these numbers through the SRC P Storage Manager The controller analyzes these statistics to optimize the array architecture cache and stripe size for your system You can tune and set cache parameters through the SRC P Storage Manager The SRC P Controller provides three independent single ended channels with three high density 68 pin external SCSI connectors that are Fast Wide and Ultra Wide capable and three 68 pin internal SCSI connectors that are Ultra Wide capable Each channel supports either internal disk drives where applicable or external storage devices but not both Each SRC P Contr
16. ing a cable backplane or PCI card particularly when two Sun Enterprise 450 server internal RAID options are installed a On the left side of the system fill in the two labels on the 8 disk UltraSCSI data cable for the appropriate connectors Fill in the number of the PCI slot used and check the box to indicate either the upper backplane or lower backplane b On the right side of the system fill in the two labels on the 8 disk UltraSCSI data cable for the appropriate connectors Check the box to indicate either the upper backplane or lower backplane Installing External Devices You need an UltraSCSI 2m cable for each external storage device that you connect to the SRC P Controller 1 If necessary power off the server See How to Power Off the System in your server owner s guide for instructions 2 Turn off any peripheral devices attached to the server 3 Connect any external storage devices to the SRC P Controller Use the external 2m cables supplied with the SRC P Controller The cable connectors are keyed so that they can only connect one way See Internal RAID Option Components on page 5 to view the location of the channels Note Do not connect external SCSI devices to a SCSI channel that is used to support internal disk drives Note External ports A and B are close together and will not accommodate non Sun external 2m cables 22 Enterprise 450 Server Internal RAID Storage Option Installa
17. l with the Phillips screw 10 If you are installing an external device only go to Installing External Devices on page 22 Otherwise go to Installing the 8 Disk Backplane on page 14 Chapter 2 Installing the Internal RAID Storage Option 13 14 Installing the 8 Disk Backplane Note If you are installing two Sun Enterprise 450 Server Internal RAID Storage Option Kits install the SRC P Controller for the upper 8 disk backplane in a PCI slot located above the SRC P Controller used for the lower 8 disk backplane Remove the disk fan tray assembly if you have not already done so See How to Remove a Disk Fan Tray Assembly in your server owner s guide On the right side of the enclosure remove the two screws that secure the 8 disk backplane filler panel to the disk cage and remove the filler panel Remove both backplane filler panels if you are installing the lower 8 disk backplane Insert the 8 disk backplane down into the 12 mounting hooks at the rear of the disk cage Use the lowest available set of hooks do not mount a backplane at the top of the disk cage if the center portion of the cage has no backplane Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 4 Secure the backplane to the disk cage using the two Phillips screws provided in the option kit Installing the Internal Cables
18. ling two storage option kits the 8 slot UltraSCSI data cable on the outside on top in the access port must connect to the SRC P Controller in the lower slot 9 If the 8 slot UltraSCSI data cable has excess slack carefully fold the cable and secure the fold using the cable clip attached to the CPU card cage Do not crease the cable when you fold it 20 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 10 Connect the other end of the cable to the 8 disk backplane Connect P2 B to the upper connector J0402 and connect P2 A to the lower connector J0102 Note If you are installing two expansion option kits the UltraSCSI data cable on the outside on top in the access port must connect to the lower 8 disk backplane 11 If the 8 disk UltraSCSI data cable has excess slack carefully fold the cable and secure the fold using the cable clip attached to the disk fan tray assembly Do not crease the cable when you fold it 12 Replace the cable access panel on top of the system chassis Align the three tabs on the edge of the panel with the corresponding slots in the system chassis 13 Secure the access panel with the three Phillips screws Chapter 2 Installing the Internal RAID Storage Option 21 14 Fill in information on the four labels at the ends of the 8 disk UltraSCSI data cable This identification is important when replac
19. lleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun AnswerBook2 docs sun com Sun Enterprise Sun Enterprise SYMON Sun StorEdge SRC P Intelligent SCSI RAID Controller Solstice DiskSuite OpenBoot SunVTS OpenWindows et Solaris sont des marques de fabrique ou des marques d pos es ou marques de service de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une licence non exclusive de Xerox sur l i
20. n If there are two UltraSCSI controller cards installed in the system and you are using the SRC P Controller to support an 8 disk storage option you need to remove one of the UltraSCSI controller cards a Disconnect the two 8 disk UltraSCSI data cable connectors from the front of the UltraSCSI controller PCI card you are removing The cables are labeled P1 A and P1 B Take note of where each connector attaches to the PCI card b Disconnect all external cables from the faceplate of the PCI card c Remove the Phillips screw that secures the faceplate of the PCI card to the back panel of the system d Pull the UltraSCSI PCI card all the way out of the slot Hold the PCI card by the edges 27 2 Install the SRC P Controller See Installing the SRC P Controller Card on page 12 3 If necessary remove the existing 8 slot UltraSCSI backplane and install the new 8 disk backplane To remove the 8 slot UltraSCSI backplane see How to Remove an 8 slot UltraSCSI Backplane in the Ultra Enterprise 450 Server Owner s Guide To install the 8 disk backplane see Installing the 8 Disk Backplane on page 14 4 If necessary install the internal SCSI data cables See Installing the Internal Cables on page 15 5 Connect any external devices See Installing External Devices on page 22 6 Reassemble the system See Reassembling the System on page 23 7 Reconfigure and reboot the system
21. n board Be sure that the tab on the right side of the connector snaps into place 18 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 4 Remove the three small Phillips screws that secure the cable access panel to the top of the system chassis T WN SK TE 5 Tilt the front edge of the access panel upward and lift it free from the chassis 19 Installing the Internal RAID Storage Option Chapter 2 6 Insert the 8 disk UltraSCSI data cable into the cable access port on the top of the system chassis Position the cable in the access port with connectors P1 A and P1 B toward the left side of the enclosure where the main logic board is located If you are installing the upper 8 disk backplane you must position the cable between the two existing data cables in the access port 7 On the left side of the enclosure carefully route the cable so that it rests on top of the shelf located directly above the top CPU module Take care to avoid damaging the cable on any sharp sheet metal edges 8 On the left side of the enclosure connect the two cable connectors to the SRC P Controller Note Channel 0 is for the 4 slot data cable Use channels 1 and 2 See Internal RAID Option Components on page 5 to view the location of the channels If necessary remove the brackets from the ends of each connector Note If you are instal
22. nterface d utilisation graphique Xerox cette licence couvrant galement les licenci s de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L ETAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFACON 5 55 4 Adobe PostScript DECLARATION OF CONFORMITY FCC Compliance Information Statement blnnuEactaret i Nagie Diiira Preoorsring Techaotagy Carporasan bianzfiscnurer s Adde 40 Conde Diese Mailand Firid 32751 BIELI Declar wader ihe sale responsibility muat die folle producti Type of Equipment BUS Cards aad Fer heul equipment Model Member PRESAHU FMCELAELTW POO PW PM15 SLI FM2SS4LDW PRLS PML PR ESAUT PMV PHOTESUE SX4058U2 SSP ele A HE4OSO LADD SFd4055 4 SMBODSO DE SM CMA Dit LE 51 amp DPT RETW fo whieh whe declaration ir im with the Tute 47 oy Mae LU Code of Federal Regulation Part 15 cavenlng Class perronal computers and peripherals Li subject to the allaeing tro conditions I this device may mod conse huer
23. nternal Disk Devices termination The SCSI target address SCSI ID of each disk drive is determined by the slot location where the drive is connected to the 8 disk backplane The backplane also provides the SCSI termination for each drive Do not use jumpers on the drive to select a specific SCSI ID Target address SCSI ID 7 is reserved for the SRC P Controller External Devices Your hardware configuration determines the number and distribution of SCSI addresses available For the Sun StorEdge MultiPack devices SCSI IDs are hardcoded You do not need to set jumpers You can view SCSI IDs through the GUI for the SRC P Controller PCI slot selection The SRC P Controller requires a 64 bit PCI slot You may install the SRC P Controller in slots 1 through 7 only For maximum performance configure the system if possible with no more than one card on each PCI bus If you are installing two 8 disk storage options install the SRC P Controller for the upper 8 disk backplane into a PCI slot located above the card used for the lower 8 disk backplane DC power The DC power requirement is 5V 5 at 3 5 amps 8 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 External Cabling Guidelines Use the following cabling guidelines to ensure proper device termination m 2m cable is required for each external device Sun part number 3832A m A maximum of 12 disks one 6 drive or one 12 drive MultiPack i
24. nternal RAID storage option into a new Sun Enterprise 450 server To upgrade a Sun Enterprise 450 server that has a SRC P Controller already installed see Chapter 3 To install the internal RAID storage option you will need to complete the following tasks m Prepare the Sun Enterprise 450 server m Install the SRC P Controller card m Install the 8 disk backplane m Install the internal SCSI cables m Connect any external devices m Reassemble the system m Reconfigure and reboot the system m Verify the installation Before You Begin Caution Persons who access this equipment must observe all safety precautions described in Appendix C of the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide m Verify that you have received all of the parts you ordered see Kit Contents on page 4 m Locate the following tools m Screwdriver Phillips 1 m Screwdriver Phillips 2 a Electrostatic discharge ESD mat Sun part number 250 1088 or equivalent Grounding wrist or foot strap m Locate the following manuals Ultra Enterprise 450 Server Owner s Guide Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide w Sun StorEdge MultiPack Installation Manual Installing the SRC P Controller Card Caution You need two power supplies in the Sun Enterprise 450 server to support the internal RAID storage option 1 Back up any data on the disks if necessary See the AnswerBook online documentation for
25. oller supports 36 disk drives per card The SRC P Controller supports disk hot plugging so that you can replace drives while the system is operational For information about hot plug disk replacement see the Sun StorEdge Multipack Storage Guide for external devices for internal disk drives see the product notes or owner s guide for your server ECC error checking and correcting memory detects and corrects data errors in the entire data path through the controller cache and other controller hardware With ECC you generate redundant information that you can use to detect and correct errors in stored or transmitted data If you are using a software RAID package such as Veritas or Solstice DiskSuite along with the SRC P Controller the software RAID package will recognize the logical devices created using the SRC P Controller Onboard temperature and voltage sensors pass critical hardware management data to the SRC P Storage Manager information windows for logging and for notifying you GUI windows also display status conditions with status flags on the drive or array icons 2 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 The onboard battery backup module supports the cache It protects data not yet written to the drives from being lost when the power is lost Using the SRC P Storage Manager you can view the battery charge status the date of initial calibration and the date of the last mainten
26. s supported per external port for up to 36 disk drives per SRC P Controller m The SCSI bus must be correctly terminated Most Sun devices use autotermination See the documentation supplied with the device m Non Sun devices are not supported Installation Scenarios The Sun Enterprise 450 server internal RAID storage option can support up to 16 internal disk drives two option kits and 36 external disk drives additional cables required TABLE 1 4 below lists installation scenarios for a new Sun Enterprise 450 server If you are upgrading an 8 bay storage expansion option to an internal RAID storage option see Upgrading an 8 Bay Storage Expansion Option on page 27 TABLE 1 4 Disk Drive Installation Scenarios for a Sun Enterprise 450 Server Number of Disk Drives Internal RAID Option Required First eight internal disk drives One Sun Enterprise 450 Server Internal RAID Storage Option Kit Last eight internal disk drives One additional Sun Enterprise 450 Server Internal RAID Storage Option Kit Eight internal disk drives and One Sun Enterprise 450 Server external storage Internal RAID Storage Option Kit Two 2m cables ordered separately Two external storage devices Sun StorEdge SRC P Intelligent SCSI RAID Controller Kit Two 2m cables ordered separately Three external storage devices Sun StorEdge SRC P Intelligent SCSI RAID Controller Kit One additional 2m cable Chapter 1 Sun Enterprise 450 Server Internal RAID
27. siful laterferegon and p thin device must accept any interference received Incleding luierlenence that mia cist andre operation 1 the annigaia hereby declare thal the equipmeal ipecitted above condarme In the ao Standard Place Maitland FI USA Date li Ha cd Position D2O 0357 004 DPT DECLARATION 0F CONFORMITY Application of Council Directive RMAEEC EMC Directive TWEIWEEC Lew Voltage Directive Standard to which Conformity is Dedared ENS5022 Class B ENZOHIHZ 1 Banane s Mame Eluriniiuiod Procex ng Teclaoiagy Cerpocation Manwbyctarms n Acre 140 Candace Drie kiling Florida 32751 AT MI 5 22 European Contrat Walienbargereir M Premier Suites D E1677 Manich amp 34 Modsusumer Blvd Germans 43 5392 ed 6 5 Casio Los E Eyes MES 2 i4 1 90 amp 231 35 Asstralan Contact 187 Phillip Averwe Anian Supplier Code Mi ss ACT 20601 Australia lA CHM Type of Equigesced SCSI Boards RAID Model Member PhOOT2 PINO PROLES PHEIL PM21222 PROD PR PROS PRESI PR FMO HIW PRM PL PACE FCO PRETISTW PMI PRO PMI RIAN PMESIGALTTHW MAO DRAGOI SS SOW SOORTMILIW RICADAT 3 Bay RAETH On Pre SALT PRETGSSLE ENCESSAU PML PRM POTS PM SUSE SXAD54LTH SXAODSU SX4055F class A BERIE BASIS SAMOS SM4D50 16 SMR CHA Dione L tbe undersi gaed bercby declare that tbe cquipenent specified abo
28. ssary to run the SRC P Controller See the installation document supplied with the controller software m If you have already installed the software for a different SRC P Controller you are ready to configure drive arrays See How to Create an Array in the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide Note When you install a new SRC P Controller the controller will automatically initiate the initial calibration cycle for the battery The calibration cycle requires approximately 24 hours to complete During the calibration cycle the SRC P Controller cache is operating in Write through mode and should not be used for performance testing When the process is completed the battery module will be ready to provide backup protection and the controller will automatically switch to Write back mode See the Sun StorEdge SRC P Intelligent SCSI RAID Controller User s Guide for more information Chapter 2 Installing the Internal RAID Storage Option 25 26 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 CHAPTER 3 Upgrading an Internal 8 Bay Storage Expansion Option to an Internal RAID Storage Option This chapter describes how to upgrade an installed 8 bay storage expansion option to an internal RAID storage option Upgrading an 8 Bay Storage Expansion Option Perform the following steps to upgrade an 8 bay storage expansion option to an internal RAID storage optio
29. tion Guide September 2000 m If you are connecting an external storage device to the upper port A on the SRC P Controller insert the connector with the flat side facing down m If you are connecting an external storage device to either port B or port C on the SRC P Controller insert the connector with the flat side facing up Reassembling the System Note After reassembling the system be sure to perform the steps in the next section Reconfiguring and Rebooting the System on page 24 to reconfigure and reboot your system so that it can use the SRC P Controller Chapter 2 Installing the Internal RAID Storage Option 23 Complete these tasks to reassemble the system Refer to the Ultra Enterprise 450 Server Owner s Guide for the information to complete each task m How to Install the Disk Fan Tray Assembly m How to Install the Left Side Panel m How to Install the Right Side Panel To install disk drives for the new backplane s complete this task m How to Install a Disk Drive in the Ultra Enterprise 450 Server Owner s Guide Reconfiguring and Rebooting the System Before th
30. tional Description TABLE A 1 Component Processor Firmware PCI SCSI Functional Description Description High performance RISC processor Operational firmware is stored in flash memory and can be updated using host utilities without requiring component replacements PCI Version 2 1 compliant 64 bit 33 MHz PCI bus up to 264 Mbytes sec transfer rate Universal PCI compliant Clock Rate 20 MHz Three internal 68 pin connectors Three external 68 pin VHDCI connectors Support of ANSI X3 131 1994 SCSI 2 specification Support of ANSI X3 277 1996 FAST 20 specification UltraSCSI synchronous wide 16 bit data transfers up to 40 Mbytes sec UltraSCSI synchronous narrow 8 bit data transfers up to 20 Mbytes sec UltraSCSI low voltage differential or single ended bus operation 29 TABLE A 1 Functional Description Continued Component Description Memory Battery DC power requirements 64 Mbyte DIMM DIMMs to be installed in the controller must conform to the following specifications Speed 60 ns EDO Size 64 Mbytes Width 32 bit Configuration 72 pin small outline Voltage 3 3V Type Nickel Metal Hydride Capacity 3800 mAH Backup time 48 hours with 64 Mbyte cache installed 65 hours with 16 Mbyte cache installed Charge time 3 hours Operating Temp 10 C to 40 C Measurement 5V 5 3 3V 0 3V Voltage 5V 5 Ripple and noise 50 mv peak to peak max Current 3 27A typi
31. tions Sun Enterprise 450 Server Internal RAID Storage Option Kit External SCSI data cable option Description The option kit includes the following parts SRC P Controller 8 disk backplane 8 slot SCSI data cable 8 slot SCSI power cable cable Electrostatic discharge strap SRC P Controller CD 2m cable for use with external storage devices Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 Internal RAID Option Components The following figures show the SRC P Controller and internal cables Channel 0 Channel 2 Channel 1 FIGURE 1 1 Sun StorEdge SRC P Intelligent SCSI RAID Controller Card Note The internal connectors for Channel 0 Channel 1 and Channel 2 correspond to the external connectors A B and C on the SRC P Controller Each channel supports either internal or external devices but not both Chapter 1 Sun Enterprise 450 Server Internal RAID Storage Option Installation 5 lt 8 Slot data cable J gt 8 Slot power cable FIGURE 1 2 Internal Cables and 8 Disk Backplane 6 Sun Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 Host System Requirements Before installing the SRC P Controller make sure that the
32. ve coniprms im the aboyer Directive and Standard Place beariand FL USA Die _ 0 Mu P _ DO caa23 010 Contents Sun Enterprise 450 Server Internal RAID Storage Option Installation About the SRC P Controller 1 Kit Contents 4 Host System Requirements 7 General Information 7 First Time Installation Information 10 Installing the Internal RAID Storage Option 11 Before You Begin 11 Installing the SRC P Controller Card 12 Installing the 8 Disk Backplane 14 Installing the Internal Cables 15 Installing External Devices 22 Reassembling the System 23 Reconfiguring and Rebooting the System 24 1 Upgrading an Internal 8 Bay Storage Expansion Option to an Internal RAID Storage Option 27 Upgrading an 8 Bay Storage Expansion Option 27 Functional Description 29 vi Enterprise 450 Server Internal RAID Storage Option Installation Guide September 2000 Preface This guide describes how to install a Sun Enterprise 450 internal RAID storage option into a Sun Enterprise 450 server It includes instructions for installing a Sun StorEdge SRC P Intelligent SCSI RAID Controller card into a Sun Enterprise 450 server and connecting internal and external devices to the card These instructions are designed for an experienced workgroup server administrator Using UNIX Commands This document may not contain information on basic UNIX commands and procedures such as shutting down the system booting the system
Download Pdf Manuals
Related Search