Data Express® Ultra320 DE200
Contents
1. Table 2 Option Pins 13 16 Drive Motor Control NOTICE This User s Guide is subject to periodic updates without notice While reason able efforts have been made to ensure the accuracy of this document Stor Case Technology Inc assumes no liability resulting from errors or omissions in this publication or from the use of the information contained herein Please check the StorCase web site at http www storcase com or contact your StorCase representative for the latest revision of this document StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Introduction 1 INTRODUCTION Packaging Information The StorCase Technology Data Express system is shipped in a container designed to provide protection and prevent damage during shipment The Data Express unit was carefully in spected before and during the packing procedure at the factory Bent or broken connectors or evidence of other damage to the Data Express should be reported to the shipper immediately Refer to Figure 1 for the package contents If the wrong Data Express model has been received please call your reseller or StorCase at 800 435 0642 to arrange for a Return Material Authorization RMA StorCase cannot accept returns which do not display an RMA number on the outside of the package Return the unit with all the original packing materials Before removing any component from its packaging discharge any static electricity by touching a pro2. Your Name Address Telephone To mail this page carefully remove it from the manual fold it staple or tape it shut and drop itin the mail To FAXthis page carefully remove it from the manual or make a photocopy and FAX it to us at 714 438 1847 Thank you for taking the time to help us make our products better Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc FOLD ALONG THIS LINE AND STAPLE SHUT NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 10686 SANTA ANA CA POSTAGE WILL BE PAID BY ADDRESSEE Kingston Technology Affiliate Fs Storcase TECHNOLOGY Safest Place for Your Data 9 17600 NEWHOPE STREET FOUNTAIN VALLEY CA 92708 9885
3. A01 StorCase Technology Inc 4 Introduction Receiving Frame Front Panel Figure 3 Key Lock Drive Power Switch This key switch assures proper seating of the drive carrier within the receiving frame turns power to the drive carrier ON and OFF and prevents unauthorized removal or installation of the carrier For the computer to access data on the disk drive the key must be turned counterclockwise to the locked position The key can be permanently attached to the locking mechanism as shown in Appen dix C Unit ID Number Indicator Figure 4 This BLUE LED displays the physical address of the Ultra320 DE200 drive carrier if the carrier is Installed and Locked in the receiving frame or if the carrier is Removed from the receiving frame If the carrier is Installed but Not Locked in the receiving frame a u will be displayed to indicate an unlocked condition The unit ID number is selected by means of the unit ID select switch inside the receiving frame using a special alignment tool supplied with the DE200 Activity Indicator A small BLUE dot next to the Unit ID Number which illuminates to show when the host computer is accessing the data on the DE200 carrier This dot will flash during communication with the host computer High Insertion Count Mating Carrier Guide Connector All Steel Receiving Frame Device Spin Down Up Timer Switch BLUE Unit ID Number Indicator BLUE Activity In
4. which are not stated herein including to the extent permitted by applicable law any implied warranty of merchantability or fitness for a particular purpose In no event will StorCase be liable to the purchaser or to any user of a StorCase product for any damages expenses lost revenues lost savings lost profits or any other incidental or consequential damages arising from the purchase use or inability to use a StorCase product even if StorCase has been advised of the possibility of such damages Copyright 2006 StorCase Technology All rights reserved All registered trademarks are the property of StorCase Technology All other logos and trademarks s are properties of their respective companies Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc iv Kingston Technology Affiliate Fs Storcase TECHNOLOGY Safest Place for Your Data Declaration of Conformity Company Name StorCase Technology Inc Corporate Office Address 17600 Newhope Street Fountain Valley CA 92708 Manufacturing Address 17600 Newhope Street Fountain Valley CA 92708 Product Name Data Express Ultra320 DE200 Model Number S20A177 S20A178 Conforms to the following standards ITE Emission EMC Directives EN 55022 1998 89 336 EEC EN 61000 3 2 Harmonic Current EN 61000 3 3 Voltage Fluctuations and Flicker EN 55024 1998 ITE Immunity EN 61000 4 2 EN 61000 4 6 EN 61000 4 3 EN 61000 4 8 EN 61000
5. 4 4 EN 61000 4 11 EN 61000 4 5 Safety Standards CSA NRTL C CAN CSA C22 2 No 950 95 UL 1950 TUV EN 60950 2000 FCC Part 15 Class A EMI Standards AS NZS 3548 Information Technology Equipment EMC Standards 2006 Year of Manufacture Signature Full name Position StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Table of Contents NTRODUCTION 1 Packaging Information essent nennen nennen nnne 1 Serial Numbers essesesesesseeseeeenee nennen tnter etre nne kk AK kk ka HAAA KAK AKA kk AA AA nennen nnn 1 Package GORnlerts emen n entm ene MA ATL General Description Receiving Frame Front Panel Receiving Frame Rear Panel INS TAEEA THONG Lco cas ot tas c tte re ee ie t dete Debet Preparations stro d Eyan 2i tate e e e E aaiae Sadr nek ie DD de dire eue InistallatiOIL e 10 eroe E A ene dede dete pese ee rmt rene a e DN AA LE sd Installing the Receiving Frame Selecting the Unit ID Number eseeeeeeeneeeneennenennnenneeneenre nennen Adjusting the Spin Down Up Timer iiii keke keke kek ke kk KAK ARAS 14 APPENDIGES ath esc ets s d b koh toe oasis deh RR Appendix A Specifications Dimensions Appendix B Factory Installed Options Solenoid Drive Lock eene is Appendix C Attaching the ON OFF Key to Non Solenoid Units 19 A
6. prominently displayed on the outside of the return package Shipments must be freight prepaid and insured and must include the product serial number a detailed description of the problem experienced and proof of the original retail purchase date Products must be properly packaged to prevent damage in transit Damage resulting from improper packaging will not be covered by this warranty The StorCase factory service center is located at 17650 Newhope Street Receiving Dock Gate 4 Fountain Valley CA 92780 U S A Free Technical Support StorCase provides free technical support If you experience any difficulty during the installation or subsequent use of a StorCase product please contact StorCase s Technical Support Department prior to servicing your system This warranty covers only repair or replacement of defective StorCase products as described above StorCase is not liable for and does not cover under warranty any costs associated with servicing and or installation of StorCase products StorCase Technical Support can be reached in the U S at 714 438 1858 or toll free at 888 435 5460 U S and Canada only StorCase European Technical Support can be reached in the U K at 44 0 1932 738900 Disclaimers The foregoing is the complete warranty for the products identified above and supersedes all other warranties and representations whether oral or written StorCase expressly disclaims all warranties for the identified products
7. 5 SECONDS A 60 SECONDS B 65 SECONDS C 70 SECONDS D 75 SECONDS E 80 SECONDS F 85 SECONDS Front of Receiving Frame 0143 Figure 10 Device Spin Down Up Timer Switch StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 15 APPENDICES Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 16 Appendix A Specifications Dimensions Appendix A Specifications Dimensions SCSI Data Express subsystems conform to the Small Computer Systems Interface SCSI Standard set by the American National Standards Institute ANSI Environmental Specifications Ambient Temperature 0 C to 50 C 45 C to 75 C Relative Humidity 10 to 80 10 to 90 Altitude 1000 to 50 000 ft 1000 to 50 000 ft 304m to 15240m 304m to 15240m Shock 10g 60g Non condensing with maximum gradient of 10 per hour 211 msec pulse width 1 2 sine wave Physical Specifications Carrier Receiving Frame 1 68 42 7mm 1 70 43 2mm 4 67 118 6mm 5 75 146 1mm 7 38 187 5mm 8 18 207 8mm 1 2Ib 0 55kg 1 3lb 0 59kg With carrier removed Chassis Reliability Maintainability MTBF 500 000 Hours MTTR 5 Minutes Preventive Maintenance None Electrical Specifications Input 45V 34mA 12V 660HA StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Appendix A Specifications Dimensions 17 Receiving oes 3 13 Fra
8. StorCase Technology Data Express Ultra320 DE200 Removable SCSI Wide Ultra320 Drive Enclosure User s Guide StorCase Technology Data Express Ultra320 DE200 Removable SCSI Wide Ultra320 Drive Enclosure User s Guide Part No P89 0000 0311A01 August 2006 Kingston Technology Affiliate ra Storcase T E Cw N oO LO G Y Safest Place for Your Data 9 StorCase Technology Inc 17600 Newhope Street Fountain Valley CA 92708 9885 Phone 714 438 1850 Fax 714 438 1847 Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc LIMITED WARRANTY STORCASE TECHNOLOGY Incorporated StorCase warrants that its products will be free from defects in material and workmanship subject to the conditions and limitations set forth below StorCase will at its option either repair or replace any part of its product that proves defective by reason of improper workmanship or materials Repair parts or replacement products will be provided by StorCase on an exchange basis and will be either new or reconditioned to be functionally equivalent to new This warranty does not cover any product damage that results from accident abuse misuse natural or personal disaster external power surge or failure or any unauthorized disassem bly repair or modification StorCase will not be responsible for any software firmware or other customer data stored within or interfacing with a StorCase product Duration of
9. Warranty Twelve Year Warranty The following StorCase products are covered by this warranty for a period of twelve 12 years from the original date of purchase from StorCase or its authorized resellers all Data Express Profile model types DX removable device enclosures Seven Year Warranty The following StorCase products are covered by this warranty for a period of seven 7 years from the original date of purchase from StorCase or its authorized resellers all Data Express Classic model types DE removable device enclosures and all Data Silo Data Stacker and InfoStation external expansion chassis except for those components integrated into or purchased separately for use with these products which are identified and covered by the three year or hard drive warranties described below All StorCase interface cables and other accessories specifically intended for use with the StorCase products identified above are also covered by this 7 year warranty Three Year Warranty The following components integrated into or purchased separately for use with StorCase Data Express Data Silo Data Stacker and or InfoStation products are subject to warranty for a period of three 3 years from the original date of purchase from StorCase or its authorized resellers all RAID controllers power supplies fans and blowers Two Year Warranty The following StorCase products are covered by this warranty for a period of two 2 years from the original d
10. anism Rotating Pawl 0286 Figure B 1 Solenoid Mechanism StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Appendix C Attaching the ON OFF Key 19 Appendix C Attaching the ON OFF Key to Non Solenoid Units The following information will provide the necessary steps to attach the ON OFF key to the key lock mechanism so that it is non removable preventing accidental key loss The procedure can be reversed to revert back to a removable key if so desired Access Hole Pawl Key Lock 0156u Make certain power is OFF to the receiving frame Locate the rectangular shaped key lock mecha nism access hole on the inside of the receiving frame Note that the pawl is in an upright position Insert the key into the key lock Rotate the key 90 degrees counterclockwise so that the pawl is visible in the access hole as shown in the figure at left Using the provided alignment tool unscrew and remove the pawl from the access hole Rotate the key 180 degrees clockwise Reinstall the pawl into the access hole with the alignment tool The key is now attached to the key lock mecha nism Figure C 1 Attaching the ON OFF Key Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 20 Appendix D Optional Accessories Appendix D Optional Accessories Carrying Case Drive Carrier DX100 DE C d Carrying Case 0014 Figure D 1 Carrying Case The optio
11. ate of purchase from StorCase or its authorized resellers all Rhino UR fixed external expansion chassis model types FJR and all RhinoJH removable device enclosures model types RJR One Year Warranty All StorCase products identified as Reconditioned or Special Inventory are covered by this warranty for a period of one 1 year from the original date of purchase from StorCase or its authorized resellers Reconditioned products may only be exchanged for reconditioned products Hard Disk Drive Warranty All hard disk drives purchased from StorCase or through its authorized resellers whether purchased separately or integrated into StorCase products are subject to the warranty terms and conditions provided by the drive manufacturer Third Party Software Warranty All third party software purchased from StorCase for use with and or as part of StorCase products is subject to the warranty terms and conditions provided by the software manufacturer StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Warranty Claim Requirements To obtain warranty service the defective product must be returned to your local authorized StorCase dealer or distributor or with prior StorCase approval to the StorCase factory service center For defective products returned directly to StorCase a Return Material Authorization RMA number must be obtained by calling StorCase Customer Service at 714 445 3455 The RMA number must be
12. ation difficult 3 Toselectthe DE200 unit ID remotely through the computer system or external expansion chassis the appropriate cable from the system must be connected to the Option Pin Connector W1 on the rear of the receiving frame as shown in Table 1 and Figure 7 Table 1 Option Pin Connector W1 Signal Descriptions Function SCSIID Ground SCSIID Ground SCSIID Ground SCSIID Ground Reserved Reserved Drive Synchronous Signal Ground Remote Start see Table 2 Ground Delay Start see Table 2 Ground Reserved Reserved Reserved Reserved Reserved Reserved OANDOOARWNDY Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 10 Installation IDO Pin1 Pin 2 ID1 Pin3 Pin 4 ID2 Pin5 Pin 6 ID3 Pin 7 Pin 8 RESERVED Pin 9 Pin 10 SYNC Pin 11 Pin 12 RMST Pin 13 Pin 14 DYST Pin 15 Pin 16 RESERVED Pin 17 Pin 18 Factory Installed Jumpers Do Not Remove RESERVED Pin 19 UI Pin 20 RESERVED Pin 21 ML Pin 22 0439h Figure 7 Receiving Frame Motherboard Option Pins W1 With the drive carrier locked in place inside the receiving frame install the DE200 into the 5 25 drive opening in the computer or expansion chassis Use the appropriate guides to position the DE200 and fasten it into place with the four 4 6 32 Phillips screws provided Figure 8 illustrates the location of the mounting holes Mount
13. dicator Receiving Frame Front 0231C a Key Lock Drive Power Switch Figure 3 Receiving Frame Front Panel StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Introduction 5 Activity Indicator Carrier Removed Carrier Installed Carrier Installed from Receiving Frame unlocked locked The number 2 shown above is for illustration purposes only It can be any valid unit ID number The letter u above middle will appear as illustrated 0064 Figure 4 Receiving Frame Unit ID Number and Activity Display Receiving Frame Rear Panel Figure 5 I O Connector J2 The input output connector provides a standard interface for 16 bit wide SCSI signals DC Power Connector P1 The Data Express uses a standard 4 pin DC power connec tor to accept DC power Option Pin Connector W1 Remote Unit ID Selection Pins 1 8 of this connector are provided for remote unit SCSI ID selection through the computer system Remote ID selection requires that the unit ID switch located on the inside of the receiving frame be set to 0 Onboard ID selection is set with a switch located on the inside of the receiving frame as shown in Figure 9 See Table 1 for pin assignments Factory Installed Jumpers There are three 3 jumpers factory installed on W1 These jumpers are located on Pins 9 amp 10 19 amp 20 and Pins 21 amp 22 NOTE Do not remove these jumpers Ultra320 DE200 Us
14. er s Guide Rev A01 StorCase Technology Inc 6 Introduction Rear Panel cont d Enable Termination Power J4 This jumper is installed at the factory and enables termination power to from the SCSI bus NOTE Do not remove this jumper Factory Installed Jumpers J3 There are two 2 jumpers factory installed on J3 One jumper is located on Pins 7 amp 8 the other on Pins 9 amp 10 68 Pin I O DC Power Connector Connector J2 P1 Option Pin Connector W1 J3 Agez J3 Jumpers pa f Factory Installed on m Pin1 Pins 7 amp 8 and Pins 9 amp 10 Do Not Remove J4 Jumper Factory Installed Do Not Remove Remote ID iDo B2 Select ID2 oo ID3 oo 9 E10 oo zi B Factory Installed Jumpers oo Do Not Remove 19 C20 Figure 5 Receiving Frame Rear View StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Installation 7 INSTALLATION NOTE A 2 Phillips screwdriver will be required during this procedure Preparation While performing the steps in this section work on a soft surface to prevent excessive shock to the drive being installed Also refer to the manufacturer s documentation provided with the drive 1 Remove the drive from its protective packaging 2 SCSI Drive Termination The DE200 does not provide onboard termination External termination must be provided Refer to the documentation provided by the drive manu facturer f
15. ing holes are provided on each side and the bottom of the receiving frame to accommodate a variety of mounting configurations Use the mounting holes which best suit the com puter or expansion chassis configuration Front of Unit m SANNAA SS A NN NN Mounting gt 7 LT Holes Left Mount 0496a Noles Sight Mounting Holes Bottom Figure 8 Receiving Frame Mounting Holes StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Installation 11 Table 2 Option Pins 13 16 Drive Motor Control RMST Function Open Open Motor spins up on Power On Open Closed Motor spins up only if SCSI Start command is received Closed Open Drive motor starts spinning up approximately 12 seconds x the SCSI ID number for each target drive 12 second minimum Closed Closed Reserved Closed Jumper installed Open Jumper removed NOTE Option Pins 13 16 Table 2 are used to remotely access the disk drive s motor control options Refer to the documentation provided by the drive manufacturer for further information 5 Adjust the front of the receiving frame so the carrier slides freely in and out on the receiving frame guides The position of adjoining peripheral units may require ad justment Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 12 Installation 6 To connect the drive to a Remote Activity LED in the computer system or expansion chassis connect the appr
16. ized prior to use with the operating System and applications software Refer to the drive and or computer manufacturer s documentation for formatting information Unit ID Number Display ID Select Rotating Switch Drive Carrier Guide Receiving Frame Drive Carrier removed Figure 9 Unit ID Select Switch Location Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 14 Installation Adjusting the Spin Down Up Timer The timer for device spin down is controlled by a small selector located in a cutout on the side of the DE200 receiving frame as shown in Figure 10 When the key is turned to the OFF position and when the timer receives a NO SCSI Activity signal from the Isolator Board it waits the specified delay time before displaying a u on the front panel of the receiving frame The amount of time required for a disk drive to spin down is approximately 15 seconds or more This number can vary depending on the type of SCSI device and manufacturer e g a Seagate Barracuda may require 45 seconds The factory configuration is set for 20 seconds A different delay time may be selected with the provided alignment tool Refer to the SCSI device manufacturer s manual for more information on required device spin down time Spin Down Up Time 0 10 SECONDS 1215 SECONDS 2 20 SECONDS 3 25 SECONDS 4 30 SECONDS 5 35 SECONDS 6 40 SECONDS 7 45 SECONDS 8 50 SECONDS 9 5
17. me i ae ne with Carrier 27mm aad ER SERERD a of T Ted 6 32 x 8 4mm e ee isolator Board DE200 Isolator Board Board m 5 75 146 1m us i 79 5mm 632 x4 oo Bottom Carrier Only i I 0 64 16 3mm L Unfastened 0 44 11 2mm Fastened Figure A 1 Ultra320 DE200 Physical Dimensions Dimensions are for reference only Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 18 Appendix B Factory Installed Options Appendix B Factory Installed Options Solenoid Drive Lock The factory installed solenoid option prevents premature removal of the carrier and drive unit until the target drive has fully spun down For most disk drives this period of time can range from 15 40 seconds depending on the type of drive being used e g Seagate Barracuda drives require up to 45 seconds Refer to the drive manufacturer s documentation for specific drive information The solenoid lock is controlled by a timing switch located on the side of the receiving frame Refer to section Adjusting the Spin Down Up Timer for further information The solenoid option provides an extra step in drive protection by preventing the removal and movement of the drive until the drive motor has fully stopped Shown with Outer Shell of Receiving Frame Removed Spin Down Timer Solenoid Control Pivoting Lock Mech
18. mentation for formatting information Selecting the Unit ID Number 1 Verify that power is turned ON to the DE200 receiving frame by turning on the computer or external expansion chassis A number should appear in the unit ID display window if the carrier is locked in place 2 Unlock the DE200 drive carrier and remove it from the receiving frame A u will be displayed initially when the unit is unlocked but will return to a number when the carrier is removed from the receiving frame StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Installation 13 WARNING Unlocking the carrier unit switches DC power off to the drive Since disk drives require a short amount of time to spin down allow about 15 seconds before pulling the carrier unit out of the receiving frame to avoid possible damage to the drive 3 Use the alignment tool supplied with the DE200 to select the unit ID number of the disk drive Refer to Figure 9 for the location of the Unit ID select switch inside the receiving frame 4 After selecting an appropriate unit ID number replace the DE200 carrier in the receiving frame and LOCK IT IN PLACE NOTE The lock on the DE200 receiving frame serves two functions 1 as a lock to secure the drive and 2 as a DC power switch for the carrier unit The lock must be engaged turned counterclockwise in order to supply power to the drive carrier 5 The new drive may need to be formatted or initial
19. nal molded plastic carrying case is designed to transport one 1 Ultra320 DE200 carrier from one site to another in a safe impact and moisture resistant environment Its compact dimensions 7 long x 9 wide x 4 high make it easy to carry and to store The foam lining is contoured to fit a single Data Express carrier Contact your StorCase dealer for further details and ordering information StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Appendix D Optional Accessories 21 Drive Cover NOTE The full drive cover may not be compatible with all 3 5 half height drives Exact drive height and fit within the Ultra320 DE100 frame can vary between drive manufacturers Please contact StorCase for technical assistance before or dering the full drive cover D Slip Drive Cover Lip into Top Rear camer E 3 Slide Drive Cover Will Fit Between Forward Making Certain the Drive and the Front Cover Lip is Inside Carrier Mounting Carrier Fasten Screws Holes Must be Drive N Towards Rear of Cover Carrier el 2 Swing Drive Cover Down Covering the Drive Make Mounting Certain You Do Holes Not Damage qp Connector Pins or Cables Disk Carrier 0067 Full Drive Cover optional Figure D 2 Full Drive Cover The full drive cover P N DX100 COV is an attractive metal cover which can provide additional protection for 3 5 half height drives preventing foreign material from coming in contact with the dri
20. opriate cable s to W1 Pins 9 amp 10 on the receiving frame motherboard as shown in Figure 5 7 Connectthe I O cable from the host adapter to the receiving frame The Pin 1 indicator on the cable must be properly aligned Refer to Figure 5 for the correct Pin 1 location NOTE No onboard termination is provided on the DE200 External termination must be provided 8 Connect the power cable from the DC power supply in the computer or expansion chassis to the power connector on the DE200 receiving frame Refer to Figure 5 for the DE200 receiving frame power connector location 9 Replace any expansion boards that may have been removed earlier Replace the System cover according to the manufacturer s instructions 10 Reconnect any system or peripheral cables removed earlier 11 Turn ON power to the computer If the installation has been successful and all cables have been properly attached the system should boot normally Although the computer may not recognize the DE200 yet the appropriate front panel LED indicators should illuminate NOTE The lock on the DE200 receiving frame functions as a lock and a DC power switch for the carrier unit The lock must be engaged turned counterclockwise in order to supply power to the carrier and installed drive unit 12 The new drive may need to be formatted or initialized prior to use with the operating System and applications software Refer to the drive and or com puter manufacturer s docu
21. or termination information 3 ID Select Jumpers Locate the ID select jumper positions on the drive and remove any jumper plugs in this area the drive carrier board will plug into this section of the drive Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 8 Installation Installation 1 Carefully insert the drive into the carrier Slide the drive towards the Drive Carrier Board so that the I O DC power and ID select connectors on the drive mate with their respective connectors on the drive carrier board Figure 6 2 Fasten the drive into place with four 4 46 32 Phillips Flat Hd screws Figure 6 Drive Not Included Drive Carrier Board Drive Carrier S 6 32 x 1 4 Phillips Flat Head Screw 4 each Figure 6 Drive Installation Assembly StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Installation 9 Installing the Receiving Frame NOTES For SCSI Ultra320 operation the Ultra320 DE200 requires Ultra320 drives Ultra320 HBA and Ultra320 compliant cabling internal and external Use a 2 Phillips screwdriver during this procedure The drive should be installed into the carrier before installing the receiving frame into the mounting bay of a computer or expansion chassis 1 Turn OFF power to the computer 2 Open the computer system according to the manufacturer s instructions If necessary temporarily remove any expansion boards that may make install
22. perly grounded metal object Serial Numbers Both the Data Express DE200 receiving frame and carrier are labeled with serial numbers These numbers must be reported to the StorCase Customer Service Representative in order to receive a Return Material Authorization RMA for warranty claims Locate the serial number labels and record the numbers in the spaces provided below Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 2 Introduction Package Contents NOTE Package contents may vary depending on model The DE200 package contents include the following items If any item is missing or damaged contact your StorCase dealer for a replacement 1 Alignment Tool 5 InsertSheet 2 Drive Lock Keys 6 6 32 Phillips Machine Hd 3 Receiving Frame Mounting Screws 4 Drive Carrier 7 6 32 Phillips F H Mounting Screws Figure 1 Package Contents StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Introduction 3 General Description NOTES For SCSI Ultra320 operation the Ultra320 DE200 requires Ultra320 drives Ultra320 HBA and Ultra320 compliant cabling internal and external Ultra320 DE200 can support Ultra320 implementations with a maximum of fifteen 15 Ultra320 drives Ultra320 repeater may be required Ultra320 DE200 receiving frames are indicated by their BLUE LED while the Ultra320 DE200 carriers are indicated by the Ultra320 logo The StorCase Technology Data Expres
23. ppendix D Optional Accessories ssseeneenennnn 20 Carrying Case EU 20 Drive Cover 21 Drive salio RD 22 Reader s COmment S i keke kek Ek KEK KK KAKA KAKA KA KA KAKA KA KAK KAK KAK KK A 23 Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc vi List of Figures Figure 1 Package Contents 00 cceeeceeceesseseeseeseeeeecsceeeeeseeaeeaeeaecseesaesaeeaesaesaesseseeseeeeseateas Figure 2 Ultra320 DE200 Receiving Frame and Carrier Figure 3 Receiving Frame Front Panel eese Figure 4 Receiving Frame Unit ID Number and Activity Display Figure 5 Receiving Frame Rear View UUUU UUUUj Figure 6 Drive Installation Assembly Figure 7 Receiving Frame Motherboard Option Pins ssa Figure 8 Receiving Frame Mounting Holes 10 Figure 9 Unit ID Select Switch Location Figure 10 Device Spin Down Up Timer Switch 14 Figure A 1 Ultra320 DE200 Physical Dimensions esee 17 Figure B 1 Solenoid Mechanism 18 Figure C 1 Attaching the ON OFF Key we 19 Figure D 1 Carrying Case 20 Figure D 2 Full Drive Cover 21 Figure DS A Drive PUG 1er ER ert ETERNI RUD Bet aE Fringe Da meds 22 List of Tables Table 1 Option Pin Signal Descriptions
24. s Ultra320 DE200 is composed of a receiving frame which supports SCSI Ultra320 interfaces and fits within a 5 25 half height peripheral slot Figure 2 This 16 bit I O can support up to 320MByte sec transfer rates The receiving frame contains one 1 removable drive carrier designed to provide durable and reliable mounting for one 1 3 5 form factor SCSI Wide Wide Ultra Wide Ultra2 Wide Ultra160 or Wide Ultra320 drive The Ultra320 DE200 allows a drive to be removed and transported to another Ultra320 DE200 equipped computer or expansion chassis and also provides the ability to secure sensitive data by removing and storing the drive safely for future use Up to fifteen 15 Ultra320 DE200 units can be attached to one host adapter The DE200 was specifically designed for use in high shock and vibration environments e g aircraft which may also have non PVC material requirements The DE200 is equipped with manual lockdown thumbscrews to secure the drive carrier within the receiving frame N Receiving Frame Drive Carrier Figure 2 Ultra320 DE200 Receiving Frame and Carrier This User s Guide describes the steps required to install the StorCase Data Express Ultra320 DE200 removable enclosure inside of a computer peripheral bay or external chassis This guide supplements documentation provided with the host computer system operating system and the drive to be installed within the carrier Ultra320 DE200 User s Guide Rev
25. ve and cables The full drive cover is similar to the cable cover provided with the Ultra320 DE200 except the full drive cover protects the drive as well as the cables It is easily installed with two 2 6 32 Phillips Flat Hd screws as shown in the illustration above Ultra320 DE200 User s Guide Rev A01 StorCase Technology Inc 22 Appendix D Optional Accessories Drive Plug Figure D 3 Drive Plug The drive plug P N DX100 PLUG is designed to fill system or external enclosure bays that are occupied by receiving frames that have no carrier units installed The purpose of the plug is to provide an attractive and functional method of directing proper air flow to the other installed devices in the system or external enclosure StorCase Technology Inc Ultra320 DE200 User s Guide Rev A01 Reader s Comments 23 Reader s Comments Please take a few moments when your computer system is up and running to send us your ideas and suggestions for improving our products and documentation Did the installation go smoothly for you Are there any changes you would like us to make either with the hardware itself or with the installation instructions Everyone at StorCase Technology is working toward the goal of providing you with the highest quality most cost effective products available on the market and we need your comments to guide our efforts We look forward to hearing from you soon Date
Download Pdf Manuals
Related Search