Home

SRS-BTM30

1. the and indications on the battery compartment Battery replacement When the batteries are weak the D indicator will start flickering and become faint or the playback sound will become distorted or unstable In such a case replace all the batteries with new ones Battery life 5 mW 5 mW output Battery type Usage time Sony alkaline Approx 15 hours battery LR6 SG Sony manganese Approx 5 hours battery R6 Usage time stated above may vary according to the temperature or conditions of use Installing the Speaker Install this unit on a level surface as illustrated below This unit can be used either laid flat or in an upright position Flat Upright 10 OPERATING THE UNIT Using the BLUETOOTH Connection By using the BLUETOOTH connection you can listen to the sound from a BLUETOOTH stereo audio source device with this unit wirelessly Example hbbbhkbb BLUETOOTH mobile phone or This unit other BLUETOOTH stereo audio source device Note For details on how to operate the device to be connected refer to the operating instructions supplied with the device On pairing What is pairing BLUETOOTH devices need to be paired with each other beforehand Once BLUETOOTH devices are paired there is no need for pairing again except in the following cases Pairing information is deleted after repair etc This unit is paired with 9 or more devices This uni
2. the BLUETOOTH connection refer to the operating instructions supplied with the mobile phone On safety The nameplate indicating operating voltage power consumption etc is located on the rear exterior Before operating the system be sure that the operating voltage of the system is identical with that of your local power supply Where purchased Operating voltage 100 240 V AC 50 60 Hz All countries regions Use only the supplied AC power adaptor After operating the system with the AC power adaptor disconnect the AC power adaptor from the wall outlet if the system is not to be used for an extended period of time Just switching the D button to off does not turn the AC power adaptor off On placement Do not set the speaker in an inclined position Do not leave the system in a location near heat sources or in a place subject to direct sunlight excessive dust moisture rain or mechanical shock On operation Do not open the cabinet Refer servicing to qualified personnel only Should any solid object or liquid fall into the system have the system checked by qualified personnel before operating it any further Although this system is magnetically shielded do not leave recorded tapes watches personal credit cards or floppy disks with magnetic coding in front of the system for an extended period of time On cleaning Do not use alcohol benzine or thinner to clean the cabine
3. the list of detected devices 3 Select SRS BTM30 shown in the display of the BLUETOOTH stereo audio source device 4 If Passcode input is required on the display of the BLUETOOTH stereo audio source device input 0000 Passcode may be called Passkey PIN code PIN number or Password 5 Start the BLUETOOTH connection from the BLUETOOTH device Some BLUETOOTH stereo audio source devices may connect with the unit automatically when pairing is complete When the BLUETOOTH connection is made properly both the D indicator green and Q indicator blue light up indicating that pairing is complete and pairing information is memorized on this unit Note If you turn off this unit or the BLUETOOTH stereo audio source device before the BLUETOOTH connection is complete pairing information is not memorized and pairing will not be completed Continued 11 12 When pairing with a BLUETOOTH stereo audio source device that cannot display a list of detected devices or that has no display You may pair the device by setting both this unit and the BLUETOOTH stereo audio source device to pairing mode For details refer to the operating instructions supplied with the device If pairing is not complete Start over from step 1 Tip To pair with other BLUETOOTH devices repeat steps 1 to 5 for each device Note Passcode of this unit is fixed to 0000 This unit cannot be paired with a BLUETOOTH ste
4. the right speaker In such a case use the optional plug adaptor PC 236MS To connect to a stereo phone type headphones jack Use the optional connecting cord RK G136 and plug adaptor PC 234S or optional connecting cords RK G136 and RK G138 1 4 The above optional accessories are not provided in some areas Listening to the sound VOLUME 5 button VOLUME buttons Check the following before operating the unit If you have been listening to the sound from the BLUETOOTH stereo audio source device stop playing on the device or terminate the BLUETOOTH connection 1 Press the button to turn on this unit The D indicator lights up 2 Start playing on the source device 3 Adjust the volume Set the volume of the source device to moderate level and press the VOLUME buttons on this unit Note A beep sounds when the volume is set to minimum or maximum 4 Press and hold the 5 button to turn off this unit after using The 5 indicator goes off Notes If connecting the speaker to a device with a built in radio or tuner radio broadcasting cannot be received or sensitivity may be reduced significantly If the source device has a bass boost function or equalizer function set them to off If these functions are on sound may be distorted If the source device s headphone output has a line switch better sound will be heard if it is set to on See the operating instructions of the source device
5. If both the BLUETOOTH connected device and the one connected to the INPUT jack are played at the same time both sounds can be heard 15 16 ADDITIONAL INFORMATION Precautions On BLUETOOTH communication BLUETOOTH wireless technology operates within a range of about 10 meters about 30 feet Maximum communication range may vary depending on obstacles person metal wall etc or electromagnetic environment E Optimal performance Limited performance The following conditions may affect the sensitivity of BLUETOOTH communication There is an obstacle such as a person metal or wall between this unit and BLUETOOTH device A device using 2 4 GHz frequency such as a wireless LAN device cordless telephone or microwave oven is in use near this unit This unit is installed on a shelf made of steel Because BLUETOOTH devices and wireless LAN IEEE802 11b g use the same frequency microwave interference may occur and resulting in communication speed deterioration noise or invalid connection if this unit is used near a wireless LAN device In such a case perform the following Use this unit at least 10 m about 30 ft away from the wireless LAN device If this unit is used within 10 m about 30 ft of a wireless LAN device turn off the wireless LAN device Install this unit and BLUETOOTH device as near to each other as possible Microwaves emitting from a BLUETOOTH device may af
6. Q Rated input power 3W Maximum input power 6W Amplifier section Rated output 3 W 3 W 10 T H D 1 kHz 4 Q Bass Boost MEGA BASS Audio input Stereo minijack x 1 Input impedance 4 7 kQ at 1 kHz General Power Three R6 size AA batteries DC 5 2V supplied AC power adaptor Dimensions w h d Approx 280 x 111 x 140 mm 11 4 x 45 5 x 55 5 in Mass Approx 750 g 1 Ib 10 oz including batteries Communication System BLUETOOTH Specification version 2 0 Output BLUETOOTH Specification Power Class 2 Maximum communication range Line of sight approx 10 m 30 ft Frequency band 2 4 GHz band 2 4000 GHz 2 4835 GHz Modulation method FHSS Compatible BLUETOOTH Profiles A2DP Advanced Audio Distribution Profile AVRCP Audio Visual Remote Control Profile Volume UPDOWN Supported Codecs SBC MP3 The actual range will vary depending on factors such as obstacles between devices magnetic fields around a microwave oven static electricity reception sensitivity aerial s performance operating system software application etc BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices 5 Codec Audio signal compression and conversion format Subband Codec S Supplied accessories Mains lead 1 AC power adaptor 1 Operating Instructions 1 Optional accessories Connecting cord RK G136 RK G138 Plug adaptor PC 234S PC 236MS T
7. S O N Y 2 695 065 12 1 Wireless Speaker System Operating Instructions C Bluetooth SRS BTM30 2006 Sony Corporation WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To reduce the risk of electrical shock do not open the cabinet Refer servicing to qualified personnel only Do not install the appliance in a confined space such as a bookcase or built in cabinet To reduce the risk of fire do not cover the ventilation of the apparatus with newspapers tablecloths curtains etc And do not place lighted candles on the apparatus To reduce the risk of fire or electric shock do not place objects filled with liquids such as vases on the apparatus Connect the AC power adaptor to an easily accessible AC outlet Should you notice an abnormality in the AC power adaptor disconnect it from the AC outlet immediately Ce Hereby Sony Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC For details please access the following URL http www compliance sony de Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be han
8. cation and Function of Parts 1 power button indicator 5 DC IN 5 2 V jack Press to turn on the unit Press and Connects the supplied AC power hold to turn off the unit adaptor cc eT d 6 INPUT audio input jack Bivens whee pase 9 Connects to the LINE OUT or to 2 ID SET pairing button headphone jack of a computer For pairing with other BLUETOOTH portable audio device etc device 7 Battery compartment 3 VOLUME buttons Insert three R6 size AA batteries Adjust the volume optional A beep sounds when the volume is set to minimum or maximum 4 Q communication status indicator Power Sources Using on the mains rear to wall outlet 4 AC power adaptor to DC IN 5 2 V jack supplied When the AC power adaptor is connected to the system internal batteries are automatically disconnected Note When connecting or disconnecting the AC power adaptor turn off the system beforehand Otherwise it may cause malfunction Note on the AC power adaptor Use only the supplied AC power adaptor Do not use any other AC power adaptor to avoid damaging the speaker gore Polarity of the plug amp Using with batteries Battery installation 1 Open the battery compartment lid rear 2 Insert three R6 size AA batteries optional Be sure to match the and indications on the batteries with
9. ded over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Sony Corporation is under license Other trademarks and trade names are those of their respective owners MPEG Layer 3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson Table Of Contents Features ees 4 Using the BLUETOOTH connection 5 Unpacking 6 Location and Function of Parts sess 7 Power Sources 8 Using on the mains sss 8 Using with batteries ss 8 Installing the Speaker 9 Using the BLUETOOTH Connection 10 OM pairing oec en es 10 On indicators see 10 Pairing with a source device 11 Listening to the s
10. evice gt Make sure all the connections have been correctly made Low sound level gt Turn up the volume of the source device as high as possible to the extent that sound is not distorted For details on volume adjustment refer to the operating instructions supplied with the device gt Turn up the volume of the unit gt Replace all the batteries with new ones if they are used with this system Distorted sound gt Turn down the volume of the source device to the point where the sound is no longer distorted For details on volume adjustment refer to the operating instructions supplied with the device gt If the source device has a bass boosts function set it to off gt Turn down the volume of the unit gt Replace all the batteries with new ones if they are used with this system There is hum or noise in the speaker output gt Make sure all the connections have been correctly made gt Make sure none of the audio devices are positioned too close to the TV set The brightness of the indicator is unstable gt The brightness of the indicator may become unstable when the volume is turned up This is not malfunction When using the BLUETOOTH connection No sound gt Ensure that this unit is not too far from the BLUETOOTH stereo audio source device or this unit is not receiving interference from a wireless LAN other 2 4 GHz wireless device or microwave oven gt Chec
11. fect the operation of electronic medical devices Turn off this unit and other BLUETOOTH devices in the following locations as it may cause an accident where inflammable gas is present in a hospital train airplane or a petrol station near automatic doors or a fire alarm This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used but security may not be enough depending on the setting Be careful when communicating using BLUETOOTH wireless technology We do not take any responsibility for the leakage of information during BLUETOOTH communication Connection with all BLUETOOTH devices cannot be guaranteed A device featuring BLUETOOTH function is required to conform to the BLUETOOTH standard specified by BLUETOOTH SIG and be authenticated Even if the connected device conforms to the above mentioned BLUETOOTH standard some devices may not be connected or work correctly depending on the features or specifications of the device Depending on the device to be connected it may require some time to start communication Notes when using with a mobile phone You cannot use this unit to talk over the telephone even if the BLUETOOTH connection between this unit and a mobile phone is made For details on operation of your mobile phone when receiving a telephone call while transmitting the sound using
12. he above optional accessories are not provided in some areas Design and specifications are subject to change without notice 21 http www sony net Printed on 7096 or more recycled paper using VOC Volatile Organic Compound free vegetable oil based ink Printed in Malaysia 2695065412
13. k that the BLUETOOTH connection is made properly between this unit and the BLUETOOTH stereo audio source device gt Pair this unit and the BLUETOOTH stereo audio source device again Sound skips or the correspondence distance is short gt If a device that generates electromagnetic radiation such as a wireless LAN other BLUETOOTH device s or a microwave oven is nearby move away from such sources gt Remove any obstacle between this unit and other BLUETOOTH device or move away from the obstacle gt Locate this unit and other BLUETOOTH device s as near as possible gt Re position this unit gt Re position other BLUETOOTH device Pairing cannot be done gt Bring this unit and the BLUETOOTH device closer together Sound is delayed gt If you watch a TV or a DVD through BLUETOOTH connection via this unit sound may lag behind the picture 19 20 Initializing This Unit You can reset this unit to its default and delete all pairing information 1 If this unit is turned on press and hold the 5 button to turn off this unit 2 While holding the D button press the ID SET button for 7 seconds or more The D indicator green and the Q indicator blue flash four times and this unit is reset to the default setting All pairing information is deleted Specifications Speaker section Speaker system 48 mm Full range magnetically shielded Enclosure type Bass reflex Impedance 4
14. ound 12 Using by Connecting with a Cord ierit 14 Hooking up the speaker 14 Listening to the sound 15 Precautions What is BLUETOOTH technology 18 Troubleshooting 19 COMMON desee ergo Hd 19 When using the BLUETOOTH connection esset Initializing This Unit Specifications Features This unit is a wireless speaker system that uses BLUETOOTH wireless technology You can enjoy listening to the sound wirelessly with your mobile phone personal computer portable music player or other BLUETOOTH supported device BLUETOOTH devices to be connected with this unit are required to support A2DP Advanced Audio Distribution Profile Powerful wireless sound Supports BLUETOOTH wireless technology Built in high power 6 W amplifier Super sensitivity neodymium magnets provide high quality sound Versatile use in multiple locations Two way power supply AC power adaptor supplied or batteries not supplied e Compact 1 piece design for easy portability Magnetically shielded design for use in close proximity to your TV set with no adverse effects to its screen Equipped with an analogue input for connection to an audio device not supporting BLUETOOTH wireless technology BLUETOOTH connection This unit can receive stereo audio signal from a BLUETOOTH ste
15. reo audio source device whose Passcode is not 0000 Listening to the sound Check the following before operating the unit The BLUETOOTH stereo audio source device s BLUETOOTH function is on Pairing of this unit and the BLUETOOTH stereo audio source device is complete If you have been listening to the sound from the source device connected to the INPUT jack stop playing on the device or turn off the device 1 Press the button to turn on this unit 2 Start the BLUETOOTH connection from the BLUETOOTH stereo audio Source device 3 Start playing on the BLUETOOTH stereo audio source device Note If the source device has a bass boost function or equalizer function set them to off If these functions are on sound may be distorted 4 Adjust the volume Set the volume of the BLUETOOTH stereo audio source device to moderate level and press the VOLUME buttons on this unit Note A beep sounds when the volume is set to minimum or maximum Notes In the following cases you need to make the BLUETOOTH connection again The power of this unit does not turn on The power of the BLUETOOTH stereo audio source device does not turn on or the BLUETOOTH function is off The BLUETOOTH function of this unit or the BLUETOOTH stereo audio source device is in sleep mode The BLUETOOTH connection is not made If both the BLUETOOTH connected device and the one connected to the INPUT jack are played at
16. reo audio source device mobile phone digital music player etc supporting A2DP By converting the wireless stereo audio signal digital to analogue audio signal you can enjoy listening to the sound with this unit a gt p gt gt gt D gt BLUETOOTH stereo audio source device This unit Connection with a cord You can enjoy listening to the sound from the device connected to the INPUT jack oneg Portable audio device CD MD player computer etc Using the BLUETOOTH connection In the example below we explain how to receive the sound played on a BLUETOOTH mobile phone with the sound playback function and listen to the sound on this unit Pairing Enables a BLUETOOTH mobile phone and this unit to recognize one another Pairi BLUETOOTH EUR mobile phone This unit For more details see pages 10 and 11 BLUETOOTH connection Operate the BLUETOOTH mobile phone to make the BLUETOOTH connection Connection Listening to the sound Enjoy listening to the sound played on the BLUETOOTH mobile phone through this unit j P LbRbbb Stereo audio signal Streaming For more details see page 12 GETTING STARTED Unpacking Check that you have the following items Wireless Speaker System 1 AC power adaptor 1 Mains lead 1 Operating Instructions 1 Lo
17. t If the TV picture or monitor display is magnetically distorted Although this system is magnetically shielded there may be cases that the picture on some TV sets personal computer sets may become magnetically distorted In such a case turn off the power of the TV set personal computer set once and after 15 to 30 minutes turn it on again For the personal computer set take the appropriate measures such as data storage before turning it off When there seems to be no improvement locate the system further away from the TV set personal computer set Furthermore be sure not to place objects in which magnets are attached or used near the TV set personal computer set such as audio racks TV stands toys etc These may cause magnetic distortion to the picture due to their interaction with the system Others If you have any questions or problems concerning this unit that are not covered in this manual please consult your nearest Sony dealer Should any problem persist consult your nearest Sony dealer 17 18 What is BLUETOOTH technology BLUETOOTH wireless technology is a short range wireless technology that enables wireless data communication between digital devices such as a computer or digital camera BLUETOOTH wireless technology operates within a range of about 10 meters about 30 feet Connecting two devices as necessary is common but some devices can be connected to multiple devices at the same time Yo
18. t can be paired with up to 8 BLUETOOTH stereo audio source devices If a new device is paired after 8 devices have been paired the device whose latest connection time is the oldest among the 8 paired devices is replaced by the new one This unit is reset All pairing information is deleted See page 20 See page 11 on how to pair devices On indicators Status 5 indicator green Q indicator blue Power on Lights up Off Pairing mode Flashes Flashes Connecting or Lights up Lights up communicating Pairing with a source device Check the following before operating the unit This unit is connected to a power source and the D indicator green goes off 1 Press and hold the ID SET button for 7 seconds or more When the D indicator green and Q indicator blue start flashing together release the button This unit enters pairing mode Note Pairing mode is cancelled and this unit is turned off after about 5 minutes If this unit is turned off while performing the procedure start over from step 1 2 Perform pairing procedure on the BLUETOOTH stereo audio source device to detect this unit The list of detected devices appear on the display of the BLUETOOTH stereo audio source device This unit is displayed as SRS BTM30 If SRS BTM30 is not displayed repeat from step 1 Notes When pairing be sure to place both the BLUETOOTH devices within 1 m 3 ft of each other Some devices cannot display
19. the same time both sounds can be heard To finish listening Terminate the BLUETOOTH connection by any of the operations below Operate the BLUETOOTH stereo audio source device to terminate the connection For details refer to the operating instructions supplied with the device Turn off the BLUETOOTH stereo audio source device Turn off this unit Tip You can adjust the volume of this unit with the BLUETOOTH stereo audio source device supporting AVRCP Audio Visual Remote Control Profile Volume UP DOWN For details refer to the operating instructions supplied with the device Note The volume of this unit may not be controlled as intended depending on the device 13 Using by Connecting with a Cord You can listen to the sound from a device connected to the INPUT jack Example Portable audio device CD This unit player computer etc Note For details on how to operate the device to be connected refer to the operating instructions supplied with the device Hooking up the speaker RK G136 connecting cord optional To LINE OUT or to rear headphones jack rear to INPUT jack 4 stereo minijack ool gt e de Sub Portable audio device CD MD player computer etc Connect the speaker to the source device When the system is connected to the monaural jack of the source device The sound may not come through
20. u do not need to use a cable for connection since BLUETOOTH technology is a wireless technology nor is it necessary for the devices to face one another such is the case with infrared technology For example you can use such a device in a bag or pocket BLUETOOTH technology is an international standard supported by millions of companies all over the world and employed by various companies worldwide This unit cannot be connected to multiple devices at the same time Communication System and Compatible BLUETOOTH Profiles of this unit Profile is standardization of the function for each BLUETOOTH device specification This unit supports the following BLUETOOTH version and profiles Communication System BLUETOOTH Specification version 2 0 Compatible BLUETOOTH Profiles A2DP Advanced Audio Distribution Profile AVRCP Audio Visual Remote Control Profile Volume UP DOWN Troubleshooting If you run into any problems using this unit use the following checklist Should any problem persist consult your nearest Sony dealer Common No sound gt Check that both this unit and the source device are turned on gt Turn up the volume of the unit gt Replace all the batteries with new ones if they are used with this system gt Turn up the volume of the source device as high as possible to the extent that sound is not distorted For details on volume adjustment refer to the operating instructions supplied with the d

SRS-BTM30

Contents

Download Pdf Manuals

Related Search

Related Contents