Home

DSM-T1

1. Item number 43 Item MY ADDR 1 Parameter 0000 0000 FFFF Function Sets an address for the unit itself if the BKSM T101 SDTI Input Board is installed in the IN 1 section of the unit When the address matches the destination address of the input signals the unit receives them 47 IN1 AUDIO CH CH1 CH2 CH3 CH4 ALL CH1 CH4 Selects the audio input signal channels to the IF OUT connector when an optional board is installed in the IN 1 section of the unit CH1 CH2 Inputs audio signals on channel 1 and 2 CH3 CH4 Inputs audio signals on channel 3 and 4 ALL CH1 CH4 Inputs audio signals on all channels When the FEC RATE is set to 7 8 ALL CH1 CH4 is selected automatically When the BKSM T103 Analog Input Board is installed and 3 pin XLR connectors are used CH1 CH2 is selected automatically regardless of the FEC RATE selection 48 IN1V SETUP 0 0 7 5 10 0 Sets the VIDEO SETUP volume to be removed from the input signals when the BKSM T103 Analog Input Board is installed in the IN 1 section of the unit Select from 0 0 to 10 0 in 0 5 steps The parameter should be the same as that of the OUT1 V SETUP of DSM R1 menu This is applicable to NTSC video signals For PAL only 0 0 can be selected 51 IN2 SDI AUDIO SDI AES EBU Selects the digital audio input signals if the BKSM T102 SDI Input Board is installed in the IN 2 section of the unit SDI
2. 2 Select a menu item to be changed using the ITEM t or v button 3 Change the parameters using the A or V button Use the lt or gt button to move a digit to the left or right 10 4 To change the parameters of other items repeat steps 2 and 3 5 Press the ENTER button The changed parameters are saved in the current bank The contents of the current bank are saved even after the power is turned off To cancel changing parameters Press the MENU button before pressing the ENTER button 6 Press the MENU button The back lighting for the MENU button turns off and the unit exits the menu To return the contents of the current bank to the factory setting Follow the procedure below 1 Press the MENU button The back lighting for the MENU button lights up and the menu appears in the display window 2 Select 93 FACTORY SET using the ITEM or button 3 Press the ENTER button The contents of the current bank return to the factory setting To cancel returning to the factory setting Press the MENU ITEM or button before pressing the ENTER button 4 Press the MENU button The back lighting for the MENU button turns off and the unit exits the menu Saving the Parameters in Menu Banks Menu banks are provided with the unit as well as the current bank The menu banks can store the 8 sets of parameters saved in the current bank Follow the procedure below to save the set of parameters i
3. 75 Q Audio characteristics Audio input connectors When the BKSM T101 is installed SDTI SDTI embedded When the BKSM T102 is installed AUDIO AES EBU SDI embedded BNC type x 1 or AES EBU BNC type x 2 selectable When the BKSM T103 is installed 3 pin XLR x 2 female AUDIO CH1 analog audio AUDIO CH2 analog audio 4 dBu High impedance 5 pin XLR x 2 male AUDIO CH1 2 analog audio AUDIO CH3 4 analog audio 4 dBu High impedance 4 R 7 8 2 R 3 4 16 bits 48 kHz Channels source Sampling frequency IF characteristics IF output connectors IF OUT BNC type x 1 75 Q 20 dBm to 0 dBm 70 140 MHz selectable IF MONITOR BNC type x 1 75 Q 10 dB for the IF OUT Supplied accessories Operating Manual 1 Installation Manual 1 Optional boards BKSM T101 SDTI Input Board BKSM T102 SDI Input Board BKSM T103 Analog Input Board Optional accessories RMM 30 Rack Mount Rail CCXA 53 conversion audio cable 5 pin XLR 3 pin XLR x 2 Design and specifications are subject to change without notice 17 IZOZTU RR NTO RAOR EIE I TEI U FHA PIS SRR A ROO GEH E ELA C LIC UE o C SHORE LICE CHREESUILU MAAR GRE 5 amp S CRRSBNCHVIASIEGATSCLESILLET The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual Sony Corporation expressly
4. EEA 8 hine 10 IUE DIS Play NEMPE 10 Changing the Parameters ener 10 Saving the Parameters in Menu Banks sees 11 Recalling the Parameters from Menu Banks sess 11 Menu St e 12 nnde 14 Operation Warninbs ener ee er eorr ettet reason eae Soa e epe store o Pe sese UE rsrsr osas 15 Erro Messages aient tic t P eene n eere radi ees ee oda eae Piin ree 15 Warr ng Messages inen icio ces tert ITE CHE HERR EFE EHE Red 15 Musso 16 The DSM TI Digital Satellite Modulator modulates analog video and audio input signals into digital signals This modulator enables an SNG Satellite News Gathering system in combination with the DSM RI Digital Satellite Demodulator The following are some of the features of the DSM T1 Easy Installation The DSM T1 provides easy connection with an existing SNG system via IF OUT Intermediate Frequency output High quality compression algorithm MPEG 4 2 2 profile at Main Level 4 2 2 PG ML ensures superior picture quality at 18 MHz transmission bandwidth Direct digital transmission at up to twice real time The DSM T1 enables transmission at up to twice real time speed at 36 MHz transmission bandwidth with connection of a DNW A100 A100P digital video cassette recorder through the SDTI Serial Data Transport Interface This feature cont
5. prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation Le mat riel contenu dans ce manuel consiste en informations qui sont la propri t de Sony Corporation et sont destin es exclusivement l usage des acqu reurs de l quipement d crit dans ce manuel Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des op rations ou entretiens de l quipement moins d une permission crite de Sony Corporation Das in dieser Anleitung enthaltene Material besteht aus Informationen die Eigentum der Sony Corporation sind und ausschlieBlich zum Gebrauch durch den K ufer der in dieser Anleitung beschriebenen Ausr stung bestimmt sind Die Sony Corporation untersagt ausdr cklich die Vervielf ltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben f r irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausr stung ohne ausdr ckliche schriftliche Erlaubnis der Sony Corporation Printed in Japan DSM T1 SY 8 So ny Corporation 1998 03 13 3 860 007 01 1 Broadcasting and Professional Systems Company O 1998
6. two pec When using the 3pin XLR connector 4 BKSM T101 BKSM T102 BKSM T103 SDTI SX Input Board SDI Input Board Analog Input Board SD f AUDIO AES EBU LI VIDEO Tx BRO AUDIO CH2 SDTI SDI AUDIO CH1 go to analog to analog composite video audio output audio output to SDTI SX output output channel 1 or 3 channel 2 or 4 DNW A100 A100P Digital Video Hybrid Recorder etc to reference BVW 75 75P Video Cassette signal input Recorder etc to SDI output Rose Sa Sn E es 7 DVW A500 A500P Digital Video Cassette Recorder DNW A100 A100P Digital Video Hybrid Recorder DNW 7 7P Digital Camcorder with the CA 701 SDI Adaptor etc 14 Operation Warnings When using the 5 pin XLR connector Error Messages When a fault is detected by the self diagnosis function that automatically performs after the power is turned on all the indicators flash and an error message ERROR XX appears in the display window The indicators do not turn off until the power is turned off to test signal output For more information about error messages refer to the Maintenance Manual Signal generator Sony Tektronix TSG 170A for the n NTSC broadcasting standard Sony Warning Messages Tektronix TSG 271 for the PAL Prondedsupg standars ele When a fault is detected while the unit is in operation the ALARM indicator lights up and a warning message OX WARNING appears i
7. 25 standard 625 625 standard 08 PASSWORD OFF Turns the password function on or off When ON is selected ON 0000 0001 set the password OFF The DSM R1 outputs normal video audio signals FFFF FFFF regardless of the password of the DSM R1 ON Sets an 8 digits password If the password of the unit does not match that of the DSM R1 no video audio signals will be output from the DSM R1 11 FREQ BW 36 MHz Selects the frequency bandwidth 18 MHz 12 FEC RATE 7 8 Selects the Forward Error Correction rate 3 4 14 IF FREQ 140 MHz Selects the output carrier frequency of the IF OUT connector 70 MHz 15 IF OUT LEVEL OdB 10dB Selects the output level of the IF OUT connector lt 10dB In OdB 10dB mode the level can be set from OdB to 20dB 10dB in 1dB steps In lt 10dB mode the level can be set from 10dB to 20dB but the displayed parameter is lt 10dB 16 CARRIER QPSK Selects whether or not to modulate the IF output signals OFF QPSK Outputs QPSK modulated wave CW OFF Outputs no IF signals CW Outputs continuous non modulated wave 41 IN1 SDI AUDIO SDI Selects the digital audio input signals if the BKSM T102 SDI AES EBU Input Board is installed in the IN 1 section of the unit SDI Digital audio signals in SDI format AES EBU Digital audio signals in AES EBU format 42 IN1 EMPHASIS OFF Turns the audio emphasis function on or off if the BKSM T103 ON Analog Input Board is installed in the IN 1 section of the unit 12
8. DIO SEL indicators IN1 indicators CH1 2 Lights up if input signals from the optional board in the IN 1 section are transmitted when The FEC RATE is 7 8 Or The FEC RATE is 3 4 and INI AUDIO CH is CH1 CH2 CH3 4 Lights up if input signals from the optional board in the IN 1 section are transmitted when The FEC RATE is 7 8 Or The FEC RATE is 3 4 and INI AUDIO CH is CH3 CH4 When the BKSM T103 Analog Input Board is installed and 3 pin XLR connectors are used the indicator does not light regardless of the FEC RATE selection To select the FEC rate select 12 FEC RATE in the menu To select the audio channels for the optional board in the IN 1 section select 47 INT AUDIO CH in the menu For more information see Menu Setup page 10 IN2 indicators CH1 2 Lights up if input signals from the optional board in the IN 2 section are transmitted when The FEC RATE is 7 8 Or The FEC RATE is 3 4 and IN2 AUDIO CH is CHI CH2 CH3 4 Lights up if input signals from the optional board in the IN 2 section are transmitted when The FEC RATE is 7 8 Or The FEC RATE is 3 4 and IN2 AUDIO CH is CH3 CH4 When the BKSM T103 Analog Input Board is installed and 3 pin XLR connectors are used the indicator does not light up regardless of the selection of the FEC RATE To select the FEC rate select 12 FEC RATE in the menu To select the audio channels for the optional board in the IN 2 section s
9. Digital audio signals in SDI format AES EBU Digital audio signals in AES EBU format 52 IN2 EMPHASIS OFF ON Turns the audio emphasis function on or off if the BKSM T103 Analog Input Board is installed in the IN 2 section of the unit 53 MY ADDR 2 0000 0000 FFFF Sets an address for the unit itself if the BKSM T101 SDTI Input Board is installed in the IN 2 section of the unit When the address matches the destination address of the input signals the unit receives them 57 IN2 AUDIO CH CH1 CH2 CH3 CH4 ALL CH1 CH4 Selects the audio input signal channels to the IF OUT connector when an optional board is installed in the IN 2 section of the unit CH1 CH2 Inputs audio signals on channel 1 and 2 CH3 CH4 Inputs audio signals on channel 3 and 4 ALL CH1 CH4 Inputs audio signals on all channels When the FEC RATE is set to 7 8 ALL CH1 CH4 is selected automatically When the BKSM T103 Analog Input Board is installed and 3 pin XLR connectors are used CH1 CH2 is selected automatically regardless of the FEC RATE selection 58 IN2 V SETUP 0 0 7 5 10 0 Sets the VIDEO SETUP volume to be removed from the input signals when the BKSM T103 Analog Input Board is installed in the IN 2 section of the unit Select from 0 0 to 10 0 in 0 5 steps The parameter should be the same as that of the OUT2 V SETUP of DSM R1 menu This is applicable to NTSC vide
10. IO connectors XLR type 5 pin male Input analog audio signals 4 channels from the audio output connectors on the BVW 75 75P Video Cassette Recorder etc CH 1 2 Inputs analog audio signals on channel 1 and 2 CH 3 4 Inputs analog audio signals on channel 3 and 4 The 5 pin XLR type can be converted to the 3 pin XLR 2 channels with the optional CCXA 53 audio cable The ITT CANNON XLR 3 11 11 conversion adapter can be also used to convert to the 3 pin XLR A menu is provided to set up the operating conditions of the unit Menu items include basic items items about the optional boards items about the front panel etc For more information about menu items see Menu List page 12 A current bank and 8 menu banks are provided with the unit The current bank can be used to store current parameters The menu banks can be used to store up to 8 sets of parameters Saving recalling frequently used parameters in from menu banks allows faster setting up of the unit s operating conditions Initial Display Switching the power on causes the selected parameter of 15 IF OUT LEVEL and 16 CARRIER on the menu to appear in the display window Changing the Parameters Follow the procedure below to change the parameters and save them in the current bank 1 Press the MENU button The back lighting for the MENU button lights up and the menu appears in the display window
11. SON Y DIGITAL SATELLITE MODULATOR DSM T1 OPERATION MANUAL 1st Edition Serial No 10001 and Higher WARNING To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules WARNING THIS WARNING IS APPLICABLE FOR USA ONLY If used in USA use the UL LISTED power cord specified below DO NOT USE ANY OTHER PO
12. WER CORD Plug Cap Parallel blade with ground pin NEMA 5 15P Configuration Cord Type SJT three 16 or 18 AWG wires Length Less than 2 5 m 8 ft 3 in Rating Minimum 10A 125 V Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug or both To reduce the risk of fire or electric shock refer servicing to qualified service personnel For the customers in the United Kingdom WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT This wires in this mains lead are coloured in accordance with the following code Green and yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red Table of Contents ly i eo E E AE E E E E E 4 Locations and Functions of Parts and Controls er 5 Front Panel 25 oett eire leta er er erts tide eru 3s FR ERR Ye Ren 5 Rear Panel 54 accent ree catia i TOE
13. asma tz EMEND S TIN VENENUM Rear Panel IN 1 section IN 2 section Q REF IN connector SPARE connector IF OUT connector jack BREAKER button AC IN socket BKSM T101 SDTI SX Input Board OUTI DIGITALJOUTPUT qp SDTI connector Q IF MONITOR connector BKSM T102 SDI Input Board AUDIO AES EBU 6 6 LT DIGTALINPUT 7 AUDIO AES EBU connectors p SDI connector The rear panel on each optional board BKSM T103 Analog Input Board 3 pin XLR Ir o NE CANALOG INPUT AUDIO connectors VIDEO connector mko ye 5 pin XLR CONE ANALOG INPUT XD AUDIO connectors Q IN 1 section Install any one of the optional boards in this section IN 2 section Install any one of the optional boards in this section For more information about installing the optional boards refer to the Installation Manual 8 REF IN reference signal input connector BNC type Inputs the reference video signals from external equipment SPARE connector D sub 25 pin female This connector is for future use IF OUT Intermediate Frequency output connector BNC type Outputs modulated IF signals to an up converter Q IF MONITOR connector BNC type Outputs IF signals to an IF monitor such as a spectrum analyzer Q ground jack Connects to a ground wire BREAKER button Excessiv
14. e ENTER button Press the MENU button The back lighting for the MENU button turns off and the unit exits the menu 11 Menu Setup Menu List Menu items are classified as one of the following categories Basic items 01 and 10 Items about an optional board in the IN 1 section on Items about an optional board in the IN 2 section on the rear panel 50 tems about the front panel 80 tems about the saving and recalling functions 90 the rear panel 40 The parameters in bold print are factory settings Item number Item Parameter Function 01 INPUT SELECT IN1 Selects either or both IN 1 or IN 2 section input signals to be IN2 transmitted from the IF OUT connector IN1 amp IN2 IN1 The input signals from the optional board in the IN 1 section are transmitted IN2 The input signals from the optional board in the IN 2 section are transmitted IN1 amp IN2 The input signals from both optional boards in the IN 1 and IN 2 sections are transmitted 02 REF SELECT EXT Selects the reference signals IN1 EXT Video signals from the REF IN connector IN2 IN1 Video signals from the input connector of the optional board in the INI 1 section IN2 Video signals from the input connector of the optional board in the INI2 section 03 VIDEO STD 525 Selects the broadcasting standard for which the unit is set up 625 525 5
15. e current in the internal circuitry will trip the primary circuit breaker automatically cutting off the power After checking that the problem has been corrected press the BREAKER button to restore the power AC IN socket Connects to an AC power outlet using the optional AC power cord This socket accepts 100 to 240 V AC power D SDTI Serial Data Transport Interface connector BNC type Inputs digital video and audio signals in SDTI SX format from the SDTI output connector on the DNW A100 A100P Digital Video Hybrid Recorder etc SDI Serial Digital Interface connector BNC type Inputs digital video and audio signals in SDI format from the SDI output connector on the DVW A500 ASOOP Digital Video Cassette Recorder etc D AUDIO AES EBU connectors BNC type Input 2 channel digital audio signals in AES EBU format from the AES EBU audio output connectors on external equipment CH 1 2 Inputs AES EBU audio signals on channels 1 and 2 CH 3 4 Inputs AES EBU audio signals on channels 3 and 4 P VIDEO connector BNC type Inputs composite analog video signals from the video output connector on the BVW 75 75P Video Cassette Recorder etc QD AUDIO connectors XLR type 3 pin female Input analog audio signals 2 channels from the audio output connectors on the BVW 75 75P Video Cassette Recorder etc CH 1 Inputs analog audio signals on channel 1 CH 2 Inputs analog audio signals on channel 2 D AUD
16. elect 57 IN2 AUDIO CH in the menu For more information see Menu Setup page 10 Q REF reference signal indicators INI Lights up when the reference signals are video signals from the input connectors of the optional board in the IN 1 section IN2 Lights up when the reference signals are video signals from the input connector of the optional board in the IN 2 section EXT Lights up when the reference signals are video signals from the REF IN connector With no signal supplied to the selected input connectors the indicator flashes To select the reference signals select 02 REF SELECT in the menu For more information see Menu Setup page 10 VIDEO STD video standard indicators 525 Lights up when the unit is set up in the 525 standard 625 Lights up when the unit is set up in the 625 standard To select the broadcasting standard select 03 VIDEO STD in the menu For more information see Menu Setup page 10 Q FREQ BW frequency bandwidth indicators 36M Lights up when the frequency bandwidth is 36 MHz 18M Lights up when the frequency bandwidth is 18 MHz To select the frequency bandwidth select 11 FREQ BW in the menu For more information see Menu Setup page 10 FEC RATE Forward Error Correction rate indicators 7 8 Lights up when the FEC rate is 7 8 3 4 Lights up when the FEC rate is 3 4 To select the FEC rate select 12 FEC RATE in the
17. menu For more information see Menu Setup page 10 D ALARM indicator When a fault is detected while the unit is in operation the ALARM indicator lights up In this case a warning message OX WARNING appears in the display window The ALARM indicator turns off when the operation returns to normal For more information about warning messages see Operation Warnings page 15 Display window Normally displays the output carrier frequency When you press the MENU button the menu appears When all the indicators flash an error message ERROR XX appears When the ALARM indicator lights up a warning message 0X WARNING appears D MENU button Displays the menu in the display window When you press the MENU button its back lighting lights up Press again to clear the menu When the menu is cleared the back lighting for the MENU button turns off For more information about the menu see Menu Setup page 10 ENTER button Saves the parameters in the current bank or memory banks QD ITEM 1 4 buttons Select the menu item when the menu is displayed in the display window D Cursor A Y 4 F buttons Use the A or V button to change the parameters Use the lt or gt button to move a digit to the left or right D RESET button Resets the unit to the status present when the power has been turned on Use a sharp pointed object to press this button Locations and Functions of Parts and Controls
18. n menu banks Recalling the Parameters from Menu Banks Follow the procedure below to recall the set of parameters from the menu banks 1 5 2 m So armen o 60 om om OH owon o SMe a b o o o Jom 1 Press the MENU button The back lighting for the MENU button lights up and the menu appears in the display window 2 Select 91 SAVE BANK using the ITEM or button 3 Select the number of the menu bank in which the contents of the current bank to be saved using the A or V button 4 Press the ENTER button The contents of the current bank are saved in the selected menu bank The contents of the menu bank are saved even after the power is turned off To cancel saving in the menu bank Press the MENU ITEM or button before pressing the ENTER button 5 Press the MENU button The back lighting for the MENU button turns off and the unit exits the menu Press the MENU button The back lighting for the MENU button lights up and the menu appears in the display window Select 92 RECALL BANK using the ITEM or button Select the number of the desired menu bank to recall the contents into the current bank using the A or V button Press the ENTER button The contents of the selected menu bank are recalled to the current bank To cancel recalling from the menu bank Press the MENU ITEM or button before pressing th
19. n the display window When the operation returns to normal the ALARM indicator turns off to signal output BKSM T103 Analog Input Board AUDIO CH3 4 VIDEO JI AUDIO el 6 NDA ANALOG INPUT VIDEO Use the list below to check the meaning of the warning AUDIO messages CH1 2 1 F inanod d Message Meaning composite to analog to analog LL EC video audio output audio output 01 FAN REAR The rear fan has stopped output channel 1 and 2 channel 3 and 4 STOP running 02 FAN The internal fan has stopped BVW 75 75P Video Cassette poe fate SWREG running gnal input Recorder etc STOP 03 REF This unit is not synchronized f f UNLOCK with the reference signal 1 With the 5 pin XLR connector use the optional CCXA 53 selected with REF SELECT in conversion audio cable or the conversion adapter the menu 04 IN1DATA Inputted signals from the OVERFLOW BKSM T101 SDTI Input Board in the IN 1 section have Setting a password oveflowed and are not being transmitted If the PASSWORD is set to ON in the menu set a 05 IN2 DATA Inputted signals from the password for the unit so that it matches that of the OVERFLOW m mI NII cet ne ea DSM RI1 If the password of the unit does not match oveflowed and are not being that of the DSM R1 the PASSWORD transmitted INCORRECT warning message appears in the display window of the DSM R1 and no audio
20. o signals For PAL only 0 096 can be selected 81 LCD CONTRAST Adjusts the contrast of the display window 82 LCD BACKLIGHT Adjusts the brightness of the display window back lighting 91 SAVE BANK Selects the menu bank in which the parameters in the current bank are to be saved 92 RECALL BANK Selects the menu bank in which the parameters to be recalled are saved 93 FACTORY SET Resets the parameters in the current bank to the factory setting 13 Connection The illustration below shows a typical connection of When using the 5 pin XLR connector see also the next the unit for digital Satellite News Gathering page There are two kinds of connectors on the BKSM T103 For more information about connecting external Analog Input Board 3 pin XLR or 5 pin XLR connector equipment refer to the equipment operation manuals SDTI SX SDI Analog equipment equipment equipment Satellite link BKSM R101 BKSM R102 BKSM R103 SDTI SX Output SDI Output Board Board DSM R1 Digital Satellite Demodulator High power amplifier Signal generator Sony Tektronix TSG 170A for the NTSC broadcasting standard Sony Tektronix TSG 271 for the PAL broadcasting standard etc to test signal output to signal output AC power cord Rear IF OUT REF IN vAC IN to a wall outlet b hp Be OTe __ mm IF MONITOR to monitor input Spectrum analyser Any
21. rd is installed in the IN 1 section of the unit ANALOG Lights up when the BKSM T103 Analog Input Board is installed in the IN 1 section of the unit IN2 indicators SDTI Lights up when the BKSM T101 SDTI Input Board is installed in the IN 2 section of the unit SDI Lights up when the BKSM T102 SDI Input Board is installed in the IN 2 section of the unit ANALOG Lights up when the BKSM T103 Analog Input Board is installed in the IN 2 section of the unit Continued 5 Locations and Functions of Parts and Controls INPUT SEL input selection indicators IN1 Lights up when input signals from the optional board in the IN 1 section are transmitted from the IF OUT connector IN2 Lights up when input signals from the optional board in the IN 2 section are transmitted from the IF OUT connector When input signals from both optional boards are simultaneously transmitted both indicators light up To select from which optional board section input signals are transmitted select 01 INPUT SELECT in the menu When no signals are supplied to the selected board slots the indicator flashes If the destination address of the input signals and the address selected in the menu are different when the BKSM T101 SDTI Input Board is installed the indicator also flashes To select the address of this unit select 43 My ADDR 1 53 MY ADDR 2 in the menu For more information see Menu Setup page 10 Q AU
22. ributes to increase of news gathering productivity Optional interface boards available The BKSM T101 SDTI Input Board the BKSM T102 SDI Input Board and the BKSM T103 Analog Input Board provide flexible choices of installing one or two boards to this unit Two program Transmission Two multiplexed video and audio signals can be transmitted simultaneously at 36 MHz transmission bandwidth This contributes to lower transmission costs 1 SDTI is defined as SMPTE 305M 4 Locations and Functions of Parts and Controls Front Panel POWER switch O PANEL INH indicator and switch OPTION indicators INPUT SEL indicators AUDIO SEL indicators Q REF indicators Q VIDEO STD indicators FREQ BW indicators FEC RATE indicators ALARM indicator QD Display window MENU button ENTER button QD ITEM buttons B Cursor A lt gt buttons D RESET button POWER switch Turns the power on and off PANEL INH inhibiting panel buttons indicator and switch Set the PANEL INH switch to ON to deactivate the MENU ENTER ITEM and cursor A W lt 4 gt buttons When the PANEL INH switch is set to ON the PANEL INH indicator lights up OPTION optional boards indicators IN1 indicators SDTI Lights up when the BKSM T101 SDTI Input Board is installed in the IN 1 section of the unit SDI Lights up when the BKSM T102 SDI Input Boa
23. video signals are output from the DSM R1 If the PASSWORD is set to OFF in the menu the DSM RI outputs the audio video signals regardless of the password of the DSM R1 For more information see Menu Setup page 10 15 Specifications General AC 100 to 240 V 50 60 Hz 1 2 A to 0 6 A 0 C to 40 C 32 F to 104 F 10 to 90 non condensing 20 C to 60 C 4 F to 140 F Power voltage Current consumption Operating temperature Operating humidity Storage temperature Dimensions 424 x 43 6 x 525 mm w h d 16 5 4 x 1 3 4 x 20 3 4 inches Mass 8 kg 17 Ibs 10 oz when two BKSM T102 are installed IF bandwidth 18 MHz 1 channel real time IF bandwidth 36 MHz 1 channel twice real time when the BKSM T101 is installed or 2 channels real time IF bandwidth 18 MHz 18 MHz at 40 dB point IF bandwidth 36 MHz 36 MHz at 40 dB point Modulation QPSK IF Intermediate Frequency 70 or 140 MHz selectable Reed solomon convolution R 7 8 3 4 Transmission mode Carrier bandwidth Error correction Video characteristics Compression MPEG2 4 2 2P ML Video input connectors When the BKSM T101 is installed SDTI SX BNC type x 1 75 Q SMPTE 305M When the BKSM T102 is installed SDI BNC type x 1 75 Q SMPTE 259M ITU R BT 656 3 16 When the BKSM T103 is installed VIDEO composite analog BNC type x 1 1 0 V p p 75 Q REF IN composite analog BNC type x 1 1 0 V p p

DSM-T1

Contents

Download Pdf Manuals

Related Search

Related Contents